The default driver sets anchor led bit to 0 when link down,
actually, the anchor bit should be set to 1, so fixes it when
link status is down.
Secondly, change the return value of cpld_set_led_id to 0, which
means leave the cpld to control led blink frequece other than the
driver itself.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When network interface is enabled, the ring enable operation is
conducted twice. This patch deletes the redundancy code of ring enable,
and integrates hnae_ae_ops.toggle_queue_status other functions to
hns_ae_start.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds get_coalesce_range api for hns, it shows
range of coalesce usecs and frames that can be set on
this interface.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver stores the high bit value of tcam data register
to the tcam data low element, stores the low bit value of tcam data
register to tcam data high element, this patch fixes this bug.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds spin lock for tcam table operation,
there maybe a race condition happens when more than
one thread try to change the tcam talbe entries.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For SoC hip06, PFC pause handled in dsaf, while hip05 in XGMAC,
so change the statistics of pfc pause in dsaf and remove the old
pfc pause frame statistics.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For debug-ports,there are two non-synchronized processes:
Speed-Auto-Negotiation and Link-Update-Status. The two
processes are towed by two different state machines.
Bond reads the speed when link up, but the speed maybe
not update the right value at that time.That make for bond's
wrong speed. Thus only one state machine should be used and
if phy_state_machine is used, it does not need to do
hns_nic_update_link_status().
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When run ethtool cmd(ethtool -t ethx) again and again for a long
time, it will be probabilistically fail. The PHYs' registers may
be on different pages, so it must be switch to the right page
before setting PHYs' registers.
And __lb_up() calls phy_start() to startup the PHYs device, but
this function may change Copper Control Register(Page 0, Register 0)
to an other value. It would cause phy loopback test fail. if we
remove phy_start(), we have to remove the relative phy_stop(),
phy_disconnect() when doing phy loopback to keep the phy stay in
right status.
Reported-by: hejun <hjat2005@huawei.com>
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Hilink3 and Hilink4 use the same xge training and xge u adaptor for
HNSv2, it needs to select which Hilink to be set before relative serdes
being configed. The hilink_access_sel is the register to do that.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error info should be printed as "set mask to 64bit fail!" instead of
"set mask to 32bit fail!" in dma_set_mask_and_coherent().
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver uses devm_ioremap_resource, it will unmap the map
automatically, remove the unnecessary the resource free.
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The annotation info for hns_nic_reset_subtask() should be
"for resetting subtask" instead of "for resetting suntask".
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS receives a packet without doing anything, but it should call
skb_reset_mac_header() to initialize the header before using
eth_hdr().
Fixes: 0d6b425a37
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For service port, hns dsaf v1 support to close tx_pause.
However, the port will be invalid when it run command
ethtool to close tx_pause. This patch will fix it.
Signed-off-by: Qianqian Xie <xieqiaqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bit fileds of PPE reset register are different between HNS v1 and
HNS v2, but the current procedure just only match HNS v1. Here is a
patch to fix it.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the patchset about adding support of ACPI (commit id is 6343488)
being applied, HNS does not depend on OF. It depends on OF or ACPI, so
the Kconfig file needs to be updated.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enet needs to get configration parameter by acpi. This patch
adds support of ACPI for enet. The configuration parameter will
be configed in BIOS.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The miscellaneous operation is implemented in BIOS, the kernel can call
_DSM method help to call the implementation in ACPI case. Here is a patch
to do that.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ACPI case, there is no interface to register phy device to mdio-bus.
Phy device has to be registered itself to mdio-bus, and then enet can
get the phy device's info so that it can config the phy-device to help
to trasmit and receive data.
HNS hardware topology is as below. The MDIO controller may control several
PHY-devices, and each PHY-device connects to a MAC device. PHY-devices
will register when each mac find PHY device in initial sequence.
cpu
|
|
-------------------------------------------
| | |
| | |
| dsaf |
MDIO | MDIO
| --------------------------- |
| | | | | |
| | | | | |
| MAC MAC MAC MAC |
| | | | | |
---- |-------- |-------- | | --------
|| || || ||
PHY PHY PHY PHY
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dsaf needs to get configuration parameter by ACPI, so this patch add
support of ACPI.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The misc operation for different hw platform may be different, if using
current implementation, it will add a new branch on each function for
every new hw platform, so we add a method for this operation.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As device_node is only used by DT case, HNS needs to treat the other
cases including ACPI. It needs to use uniform ways to handle both of
DT and ACPI. This patch chooses phy_device, and of_phy_connect and
of_phy_attach are only used by DT case. It needs to use uniform interface
to handle that sequence by both DT and ACPI.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As device_node is only used by DT case, it is expected to find uniform
ways. So fwnode_handle is the suitable method.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As irq_of_parse_and_map is only used by DT case, it is excepted to use
a uniform interface. So it is used platform_get_irq() instead.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OF series functions can be used only for DT case. Use unified
device property function instead to support both DT and ACPI.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hns-mdio needs to register itself to mii-bus. The info of the device can
be read by both DT and ACPI.
HNS tries to call Linux PHY driver to help access PHY-devices, the HNS
hardware topology is as below. The MDIO controller may control several
PHY-devices, and each PHY-device connects to a MAC device. The MDIO will
be registered to mdiobus, then PHY-devices will register when each mac
find PHY device.
cpu
|
|
-------------------------------------------
| | |
| | |
| dsaf |
MDIO | MDIO
| --------------------------- |
| | | | | |
| | | | | |
| MAC MAC MAC MAC |
| | | | | |
---- |-------- |-------- | | --------
|| || || ||
PHY PHY PHY PHY
And the driver can handle reset sequence by _RST method in DSDT in ACPI
case.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hns-mdio only supports DT case now. do some cleanup to prepare
for introducing other cases later, no functional change.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the statement
assert(priv || priv->ae_handle);
the right side of || is only evaluated if priv is null.
v2:
As suggested by David Leight and David Miller the assert
statements are removed.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indexes should generally be avoided. So we use reg rather than port-id to
index ports.
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because cpld-ctrl-reg property is offset base on cpld-syscon property,
we make it as a cell in the cpld-syscon property.
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port mode offset for each dsaf port is different. The current code is not
so readability. This patch adds configuration named port-mode-offset to
make the code simple and more readability. If port-mode-offset isn't
exists, default value 0 will be used.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reset offset for each port in a dsaf is different. The current code is
not so readability. This patch adds configuration named port-rst-offset to
make the code simple and more readability. If this attribute doesn't exist,
default value of this attribute is equal to its port index.
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds attribute cpld_ctrl for dsaf port node, parses the syscon
for mac_cb from dts, and changes the method of access the cpld related
registers through syscon.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two kinds of dsaf device in hns, one is for service ports,
contains crossbar in it, can work under different mode. Another is for
debug port, only can work under "single-port" mode. The current code only
declared a dsaf device for both service ports and debug ports. This patch
separate it to three platform devices.
Here is the diagram of all port in one platform device(old):
CPU
|
| DSAF(one platform device)
-------------------------------------------------------------- /
| | | | | /
| PPE PPE PPE | /
| | | | | /
| | | | | /
| crossbar | | | /
| | | | |/
| ----------------------------------- | | |
| | | | | | | | | |
| | | | | | | | | |
| MAC MAC MAC MAC MAC MAC MAC MAC |
| | | | | | | | | |
--------------------------------------------------------------
| | | | | | | |
PHY PHY PHY PHY PHY PHY PHY PHY
Here is the diagram of separate all ports to three platform(new):
CPU
|
-----------------------------------
| | |
---------------------------------------------- --------- ---------
| | | | | | | |
| PPE | | PPE | | PPE |
| | | | | | | | |
| | | | | | | | |
| crossbar | | | | | | |
| | | | | | | | |
| ---------------------------------- | | | | | | |
| | | | | | | | | | | | | |
| | | | | | | | | | | | | |
| MAC MAC MAC MAC MAC MAC | | MAC | | MAC |
| | | | | | | | | | | | | |
---------------------------------------------- --------- ---------
| | | | | | \ / | / |
PHY PHY PHY PHY PHY PHY \ / PHY / PHY
\ / /
\ / /
DSAF(three platform device)
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch tunes the header file by the alphabetical order.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides the read/write function for dsaf to
access the registers through syscon methods.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the subctrl reset offset for dsaf, this property is used to reset
xge/ge ports for different dsaf. If this attribute is not present,
default value 0 will be used.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch parse port-idx-in-ae in enet node. In NIC mode of DSAF, all 6
PHYs of service DSAF are taken as ethernet ports to the CPU. The
port-idx-in-ae can be 0 to 5. Here is the diagram:
+-----+---------------+
| CPU |
+-+-+-+---+-+-+-+-+-+-+
| | | | | | | |
debug debug service
port port port
(0) (0) (0-5)
In Switch mode of DSAF, all 6 PHYs of service DSAF are taken as physical
ports connect to a LAN Switch while the CPU side assume itself have one
single NIC connect to this switch. In this case, the port-idx-in-ae will
be 0 only.
+-----+-----+------+------+
| CPU |
+-+-+-+-+-+-+-+-+-+-+-+-+-+
| | service| port(0)
debug debug +------------+
port port | switch |
(0) (0) +-+-+-+-+-+-++
| | | | | |
external port
when port-idx-in-ae is not exists, old attribute port-id will be used
(only for compatible purpose, not recommended to use port-id in new code).
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As debug ports are moved from service dsaf to debug dsaf,
the interrupts offset should start from 0, So this patch
re-defines the offset index of debug ports.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new dsaf mode named "single-port" mode for debug port.
This mode only contains one debug port. This patch also changes the
method of distinguishing the port type.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds support of pause ctrl for HNS V2, and this feature is lost
by HNS V1:
1) service ports can disable rx pause frame,
2) debug ports can open tx/rx pause frame.
And this patch updates the REGs about the pause ctrl when updated
status function called by upper layer routine.
Signed-off-by: Lisheng <lisheng011@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Missing device reference in IPSEC input path results in crashes
during device unregistration. From Subash Abhinov Kasiviswanathan.
2) Per-queue ISR register writes not being done properly in macb
driver, from Cyrille Pitchen.
3) Stats accounting bugs in bcmgenet, from Patri Gynther.
4) Lightweight tunnel's TTL and TOS were swapped in netlink dumps, from
Quentin Armitage.
5) SXGBE driver has off-by-one in probe error paths, from Rasmus
Villemoes.
6) Fix race in save/swap/delete options in netfilter ipset, from
Vishwanath Pai.
7) Ageing time of bridge not set properly when not operating over a
switchdev device. Fix from Haishuang Yan.
8) Fix GRO regression wrt nested FOU/GUE based tunnels, from Alexander
Duyck.
9) IPV6 UDP code bumps wrong stats, from Eric Dumazet.
10) FEC driver should only access registers that actually exist on the
given chipset, fix from Fabio Estevam.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (73 commits)
net: mvneta: fix changing MTU when using per-cpu processing
stmmac: fix MDIO settings
Revert "stmmac: Fix 'eth0: No PHY found' regression"
stmmac: fix TX normal DESC
net: mvneta: use cache_line_size() to get cacheline size
net: mvpp2: use cache_line_size() to get cacheline size
net: mvpp2: fix maybe-uninitialized warning
tun, bpf: fix suspicious RCU usage in tun_{attach, detach}_filter
net: usb: cdc_ncm: adding Telit LE910 V2 mobile broadband card
rtnl: fix msg size calculation in if_nlmsg_size()
fec: Do not access unexisting register in Coldfire
net: mvneta: replace MVNETA_CPU_D_CACHE_LINE_SIZE with L1_CACHE_BYTES
net: mvpp2: replace MVPP2_CPU_D_CACHE_LINE_SIZE with L1_CACHE_BYTES
net: dsa: mv88e6xxx: Clear the PDOWN bit on setup
net: dsa: mv88e6xxx: Introduce _mv88e6xxx_phy_page_{read, write}
bpf: make padding in bpf_tunnel_key explicit
ipv6: udp: fix UDP_MIB_IGNOREDMULTI updates
bnxt_en: Fix ethtool -a reporting.
bnxt_en: Fix typo in bnxt_hwrm_set_pause_common().
bnxt_en: Implement proper firmware message padding.
...
It may fail to set coalesce usecs to HW, and Ethtool needs to know if it
is successful to cfg the parameter or not. So it needs return the errno by
dsaf.ko.
Signed-off-by: Lisheng <lisheng011@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The overtime setting and getting REGs in HNS V2 is defferent from HNS V1.
It needs to be distinguished between them if getting or setting the REGs.
Signed-off-by: Lisheng <lisheng011@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are only three patches this time, most other changes to
files in include/asm-generic tend to go through the tree of whoever
depends on the change.
Two patches are cleanups for stuff that is no longer needed,
the main change is to adapt the generic version of BUG_ON()
for CONFIG_BUG=n to make it behave consistently with BUG().
This avoids undefined behavior along with a number of warnings
about that undefined behavior in randconfig builds when
we keep going on after hitting a BUG_ON().
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8tPL
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"There are only three patches this time, most other changes to files in
include/asm-generic tend to go through the tree of whoever depends on
the change.
Two patches are cleanups for stuff that is no longer needed, the main
change is to adapt the generic version of BUG_ON() for CONFIG_BUG=n to
make it behave consistently with BUG().
This avoids undefined behavior along with a number of warnings about
that undefined behavior in randconfig builds when we keep going on
after hitting a BUG_ON()"
* tag 'asm-generic-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: remove old nonatomic-io wrapper files
asm-generic: default BUG_ON(x) to if(x)BUG()
asm-generic: page.h: Remove useless get_user_page and free_user_page
The hilink status reg in HNS V2 is different from HNS v1. In HNS V2, It
distinguishes differnt lane status according to the bit-field of the reg.
As is shown below:
[0:0] ---> lane0
[1:1] ---> lane1
...
But the current driver reads the reg to get the hilink status ONLY
concidering HNS V1 situation. Here is a patch to support both of them.
Signed-off-by: Sheng Li <lisheng011@huawei.com>
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a misuse of PTR as shown below:
ae_node = (void *)of_parse_phandle(dev->of_node,
"ae-handle",
0);
if (IS_ERR_OR_NULL(ae_node)) {
ret = PTR_ERR(ae_node);
dev_err(dev, "not find ae-handle\n");
goto out_read_prop_fail;
}
if the ae_node is NULL, PTR_ERR(ae_node) means it returns success. And the
return value should be -ENODEV.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hns V1, common_poll should check and clean fbd pkts, because it
can not pend irq to clean them if there is no new pkt comes in.
But hns V2 hw fixes this bug, and will pend irq itself to do this.
So, for hns V2, we set ring_data->fini_process to NULL.
Signed-off-by: Sheng Li <lisheng011@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable head in hns_nic_tx_fini_pro has read a value, but it is
obviously no use. The patch will fix it.
And the comment is nothing to do with the routine, so it has to be removed
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return values in the first two functions mdiobus_write()
are ignored. The patch will fix it.
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It misses string format in function snprintf(), as below:
snprintf(buff, ETH_GSTRING_LEN, g_gmac_stats_string[i].desc);
It needs to add "%s" to fix it as below:
snprintf(buff, ETH_GSTRING_LEN, "%s", g_gmac_stats_string[i].desc);
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cycle index should be varied while the variable j is a fixed value.
The patch will fix this bug.
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When set MTU to the minimum value 68, there are increasing number
of error packets occur, which is caused by the overflowed value of
mss. This patch fix the bug.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If mtu for debug port is set more than 1500, it may cause that packets
are dropped by ppe. So maximum value for debug port should be 1500.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In chip V1, the maximum mtu value is 9600. But in chip V2, it is 9728.
And it is always configurates as 9600 before this patch.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If trying to get receive flow hash indirection table by ethtool, it needs
to call .get_rxnfc to get ring number first. So this patch implements the
.get_rxnfc of ethtool. And the data type of rss_indir_table is u32, it has
to be multiply by the width of data type when using memcpy.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both .get_rxfh and .set_rxfh are always return 0, it should return result
from hardware when getting or setting rss. And the rss function should
return the correct data type.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the user manual of HNS V2 describs, XGE_DFX_CTRL_CFG.xge_dfx_ctrl_cfg
should be configed as zero if we want xge statistic reg to be read only.
But HNS V1 gets the other meanings. It needs to be identified the process
and then config it rightly.
Signed-off-by: Qianqian Xie <xieqianqian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending a pause frame out from GMACs, the packets' source MAC address
does not match the GMACs' MAC address. It causes by the condition before
the mac address setting routine for GMACs, the mac address cannot be set
into loacal mac table for service ports. It obviously the condition needs
to be deleted.
Signed-off-by: Sheng Li <lisheng011@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Debug ports receives lots of packets with dest mac addr does not match
local mac addr, because the filter is close, and it does not drop the
useless packets. This patch adds ON/OFF switch of filtering the packets
whose dest mac addr do not match the local addr in mac table. And the
switch is ON in initialization.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In chip V2, the default value of port id in tx BD is Zero. If it is not
configurated to the other value, all management packets will be sent out
from port0. So port_id in the tx BD needs to be updated when sending a
management packet.
In V2 chip, when sending mamagement packets, the driver should
config the port id to BD descs.
Signed-off-by: Sheng Li <lisheng011@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current upstreaming code fails to ping other IPv6 net device, because
the enet receives the multicast packets with the src mac addr which is the
same as its mac addr. These packets need to be dropped.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It will always be passed if the soc is tested the loopback cases. This
patch will fix this bug.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MFD_SYSCON depends on HAS_IOMEM so when selecting it avoid unmet
direct dependencies.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The two header files got moved to include/linux, and most
users were already converted, this changes the remaining drivers
and removes the files.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Yisen Zhuang <yisen.zhuang@huawei.com>
This patch replace the assoication between dsaf and enet from string
matching to object reference. It requires the DTS to be updated within
BIOS. Thanks god it can be done for all released boards.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current upstreaming code fails to set the tso_mode register
when initilizes, when processes large size packets, the default 4 bd is
not enough, so this patch initilizes it and set the default value to 8 bds
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As dtsi files use the normal naming conventions using '-' instead of '_'
inside of property names, the driver needs to update the phandle name
strings of the of_parse_phandle func.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when build_skb failed, we should goto refill the buffer.
Signed-off-by: Weidong Wang <wangweidong1@huawei.com>
Acked-by: Ding Tainhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into the phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have mdio_alloc() create the array of interrupt numbers, and
initialize it to POLLING. This is what most MDIO drivers want, so
allowing code to be removed from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we have a phydev, make use of it and the phy_read() function.
This will help with later refactoring.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc fails to see that the use of the 'last_offset' variable
in hns_nic_reuse_page() is used correctly and issues a bogus
warning:
drivers/net/ethernet/hisilicon/hns/hns_enet.c: In function 'hns_nic_reuse_page':
drivers/net/ethernet/hisilicon/hns/hns_enet.c:541:6: warning: 'last_offset' may be used uninitialized in this function [-Wmaybe-uninitialized]
This simplifies the function to make it more obvious what is
going on to both readers and compilers, which makes the warning
go away.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use to_platform_device() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
printf() has a dedicated specifier to print MAC addresses. Use it instead of
pushing each byte via stack.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark address pointer with __iomem in the IO accessors.
Otherwise we will get a sparse complain like following
.../hns/hns_dsaf_reg.h:991:36: warning: incorrect type in argument 1 (different address spaces)
.../hns/hns_dsaf_reg.h:991:36: expected unsigned char [noderef] [usertype] <asn:2>*base
.../hns/hns_dsaf_reg.h:991:36: got void *base
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
here is the patch raising the performance of XGE by:
1)changes the way page management method for enet momery, and
2)reduces the count of rmb, and
3)adds Memory prefetching
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the initializzation code to disable the hardware
vlan support for VLAN Tag stripping by default for now.
Proper support of "hardware VLAN assitance" feature would
soon come in the next coming patches.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of ethtool TSO option to support
Hip06 SoC to HNS
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lisheng <lisheng011@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of "TSO (TCP Segment Offload)" feature
provided by the Hip06 ethernet hardware to the HNS ethernet
driver.
Enabling this feature would help offload the TCP Segmentation
process to the Hip06 ethernet hardware. This eventually would help
in saving precious cpu cycles.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lisheng <lisheng011@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of "RSS (Receive Side Scaling)" feature
provided by the Hip06 ethernet hardware to the HNS ethernet
driver.
This feature helps in distributing the different flows (mapped as
hash by hardware using Toeplitz Hash) to different Queues asssociated
with the processor cores. The mapping of flow-hash values to the
different queues is stored in indirection table (which is per Packet-
parse-Engine/PPE). This patch also provides the changes to re-program
the (flow-hash<->Qid) mapping using the ethtool.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Reviewed-by: Kenneth Lee <liguozhu@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patchset adds support of Hisilicon Hip06 SoC to the existing HNS
ethernet driver.
The changes in the driver are mainly due to changes in the DMA
descriptor provided by the Hip06 ethernet hardware. These changes
need to co-exist with already present Hip05 DMA descriptor and its
operating functions. The decision to choose the correct type of DMA
descriptor is taken dynamically depending upon the version of the
hardware (i.e. V1/hip05 or V2/hip06, see already existing
hisilicon-hns-nic.txt binding file for detailed description). other
changes includes in SBM, DSAF and PPE modules as well. Changes
affecting the driver related to the newly added ethernet hardware
features in Hip06 would be added as separate patch over this and
subsequent patches.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: lisheng <lisheng011@huawei.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_driver doesn't need to set .owner, because
platform_driver_register() will set it.
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
delete action of ETHTOOL_ID_ON/ETHTOOL_ID_OFF in XGE ethtool -p,
so Hardware control the LED state instead of software.
Signed-off-by: Li Peng <lipeng321@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the global Soc configuration is treated by syscon, and sub ctrl bus is
Soc bus. it has to be treated by syscon.
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: lisheng <lisheng011@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/hisilicon/hns/hnae.c:442:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
CC: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BITS_RX_EN is an 'unsigned long' constant, so the ones complement of that
has bits set that do not fit into a 32-bit variable on 64-bit architectures,
which causes a harmless gcc warning:
drivers/net/ethernet/hisilicon/hix5hd2_gmac.c: In function 'hix5hd2_port_disable':
drivers/net/ethernet/hisilicon/hix5hd2_gmac.c:374:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
writel_relaxed(~(BITS_RX_EN | BITS_TX_EN), priv->base + PORT_EN);
This adds a cast to (u32) to tell gcc that the code is indeed fine.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HNS MDIO driver fails to build on older ARM machines that are not
yet converted to CONFIG_OF:
drivers/net/ethernet/hisilicon/hns_mdio.c: In function 'hns_mdio_bus_name':
drivers/net/ethernet/hisilicon/hns_mdio.c:405:14: error: 'OF_BAD_ADDR' undeclared (first use in this function)
u64 taddr = OF_BAD_ADDR;
^
drivers/net/ethernet/hisilicon/hns_mdio.c:405:14: note: each undeclared identifier is reported only once for each function it appears in
drivers/net/ethernet/hisilicon/hns_mdio.c:409:11: error: implicit declaration of function 'of_translate_address' [-Werror=implicit-function-declaration]
taddr = of_translate_address(np, addr);
^
This clarifies the dependency to ensure we don't attempt to build these
drivers without CONFIG_OF, but also adds a COMPILE_TEST alternative to
give us better build coverage testing.
Build-tested on x86 as well to ensure this actually works.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some configurations fail to build the hns dsaf code because of
a missing header file:
ethernet/hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_init':
ethernet/hisilicon/hns/hns_dsaf_main.c:1096:2: error: implicit declaration of function 'vzalloc' [-Werror=implicit-function-declaration]
priv->soft_mac_tbl = vzalloc(sizeof(*priv->soft_mac_tbl)
This adds the correct #include.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch fixes the bug triggered timeout sequence. when the connective
ports cannot accept the packets with higher speed, they will send out the
pause frame to the Soc's mac. At that time, the driver resets the relevant
of the Soc, then it causes the packets cannot be sent out immediately.
this patch fixes the issue.
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: lisheng <lisheng011@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
before this patch, hns driver only permits user to set the net device
by using ethtool -s when the device is link up. it is obviously not so
good. it needs to be set no matter it is link up or down. so this patch
fixes this issue.
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: lisheng <lisheng011@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: Chenny Xu <chenny.xu@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the wrong judgement of mac_id when get port num.
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the hns driver hnae sysfs interface according to
Arnd's review comments.
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().
v2: removed unused variable
v3: removed another unused variable
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch fixes a bug in hns driver. when we want to get statistic info
by using ethtool -S, it shows us there are 3 wrong counters info. because
the strings related to the registers are wrong. it needs to modify the
strings which give us wrong info.
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch fixes a bug in hns driver. the link led is on at the beginning,
but at this time the ethernet port is on down status. it needs to reset
the led status on init sequence.
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch adds support to set promisc mode. it configs the queue on
init seq when it is on promisc mode.and being enabled or disabled promisc
mode by upper level user.
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the building error reported by Jiri Pirko <jiri@resnulli.us>
drivers/net/ethernet/hisilicon/hns/hnae.h:465:2: error: unknown type
name 'phy_interface_t'
phy_interface_t phy_if;
^
the full build log is on https://lists.01.org/pipermail/kbuild-all.
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: yankejian <yankejian@huawei.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newly introduced HNS_MDIO Kconfig symbol selects 'MDIO', but
that is the wrong symbol as the code used by this driver is
provided by PHYLIB rather than the MDIO driver. Also, there is
no need to make this driver user selectable, because it is already
selected by all drivers that need it.
This changes the Kconfig file to select the correct library, and
to make the option silent.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 5b904d3940 ("net: add Hisilicon Network Subsystem MDIO support")
Signed-off-by: David S. Miller <davem@davemloft.net>
The recently added hns driver causes a build warning in ARM
allmodconfig builds:
drivers/net/ethernet/hisilicon/hns/hnae.c: In function 'handles_show':
drivers/net/ethernet/hisilicon/hns/hnae.c:452:13: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
j, (u64)h->qs[i]->io_base);
^
This removes the pointless cast and prints the pointer address using
the "%p" format string in all three locations.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the compilation error with arm allmodconfig, this error
generated due to unavailability of readq() on 32-bit platform which was
found during net-next daily compilation. In the same time, fix all the
hns drivers compilation warnings.
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: zhaungyuzeng <Yisen.zhuang@huawei.com>
Signed-off-by: kenneth Lee <liguozhu@hisilicon.com>
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function can return negative value.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to add basic ethernet support for HNS. It is one of the way to
use the HNS acceleration engine. But most of the decoding/encoding
capability of the AE cannot be used in this way.
This submit contains the basic feature as a ethernet driver. More will
be added later.
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: Kenneth Lee <liguozhu@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSAF, namely Distributed System Area Fabric, is one of the HNS
acceleration engine implementation. This patch add DSAF driver to the
system.
hns_ae_adapt: the adaptor for registering the driver to HNAE framework
hns_dsaf_mac: MAC cover interface for GE and XGE
hns_dsaf_gmac: GE (10/100/1000G Ethernet) MAC function
hns_dsaf_xgmac: XGE (10000+G Ethernet) MAC function
hns_dsaf_main: the platform device driver for the whole hardware
hns_dsaf_misc: some misc helper function, such as LED support
hns_dsaf_ppe: packet process engine function
hns_dsaf_rcb: ring buffer function
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: Kenneth Lee <liguozhu@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNAE (Hisilicon Network Acceleration Engine) is a framework to provide a
unified ring buffer interface for Hisilicon Network Acceleration
Engines.
With the interface, upper layer can work as ethernet driver, ODP driver
or other service driver on purpose.
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: Kenneth Lee <liguozhu@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO support for Hisilicon Network Subsystem. It is used in Hislicon
hip04, hip05 and Hi1610 SoC to control the external PHY
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: Kenneth Lee <liguozhu@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it. And there is
no value in anyone else taking over updating it either.
However the references to it continue to spread as boiler plate text
from one Kconfig file into the next. We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.
No code is changed in this commit, just Kconfig help text.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
None of those drivers uses last_rx for its own needs.
See 4dc89133f4 ("net: add a comment on
netdev->last_rx") for reference.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Zhangfei Gao <zhangfei.gao@linaro.org>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code sets the expiry value of the timer to a relative value and
starts it with hrtimer_start_expires. That's fine, but that only works
once. The timer is started in relative mode, so the expiry value gets
overwritten with the absolut expiry time (now + expiry).
So once the timer expired, a new call to hrtimer_start_expires results
in an immidiately expired timer, because the expiry value is
already in the past.
Use the proper mechanisms to (re)start the timer in the intended way.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: dingtianhong <dingtianhong@huawei.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Zhangfei Gao <zhangfei.gao@linaro.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: netdev@vger.kernel.org
Acked-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hip04 ethernet driver causes a new compile-time warning
when built as a loadable module:
WARNING: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/hisilicon/hip04_eth.o
see include/linux/module.h for more information
This adds the license as "GPL", which matches the header of the file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The if block was supposed to have curly braces. In the current code we
complain about dropped rx packets when we shouldn't.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support Hisilicon hip04 ethernet driver, including 100M / 1000M controller.
The controller has no tx done interrupt, reclaim xmitted buffer in the poll.
v13: Fix the problem of alignment parameters for function and checkpatch warming.
v12: According Alex's suggestion, modify the changelog and add MODULE_DEVICE_TABLE
for hip04 ethernet.
v11: Add ethtool support for tx coalecse getting and setting, the xmit_more
is not supported for this patch, but I think it could work for hip04,
will support it later after some tests for performance better.
Here are some performance test results by ping and iperf(add tx_coalesce_frames/users),
it looks that the performance and latency is more better by tx_coalesce_frames/usecs.
- Before:
$ ping 192.168.1.1 ...
=== 192.168.1.1 ping statistics ===
24 packets transmitted, 24 received, 0% packet loss, time 22999ms
rtt min/avg/max/mdev = 0.180/0.202/0.403/0.043 ms
$ iperf -c 192.168.1.1 ...
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 1.0 sec 115 MBytes 945 Mbits/sec
- After:
$ ping 192.168.1.1 ...
=== 192.168.1.1 ping statistics ===
24 packets transmitted, 24 received, 0% packet loss, time 22999ms
rtt min/avg/max/mdev = 0.178/0.190/0.380/0.041 ms
$ iperf -c 192.168.1.1 ...
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 1.0 sec 115 MBytes 965 Mbits/sec
v10: According David Miller and Arnd Bergmann's suggestion, add some modification
for v9 version
- drop the workqueue
- batch cleanup based on tx_coalesce_frames/usecs for better throughput
- use a reasonable default tx timeout (200us, could be shorted
based on measurements) with a range timer
- fix napi poll function return value
- use a lockless queue for cleanup
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the hix5hd2 XGMAC 1Gb ethernet device.
The controller requires two queues for tx and two queues for rx.
Controller fetch buffer from free queue and then push to used queue.
Diver should prepare free queue and free buffer from used queue.
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
