Fix be_find_vfs() to check for matching bus number as well along with devfn
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/qmi_wwan.c
net/batman-adv/translation-table.c
net/ipv6/route.c
qmi_wwan.c resolution provided by Bjørn Mork.
batman-adv conflict is dealing merely with the changes
of global function names to have a proper subsystem
prefix.
ipv6's route.c conflict is merely two side-by-side additions
of network namespace methods.
Signed-off-by: David S. Miller <davem@davemloft.net>
Increasing the hardware statistics structure to accomodate statistics for skyhawk.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify IOCTL error message to print subsystem also.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum size of packet that can be handled by controller including ethernet
header is 65535. Reducing gso_max_size accordingly.
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
drivers/net/wireless/iwlwifi/pcie/trans.c
The iwlwifi conflict was resolved by keeping the code added
in 'net' that turns off the buggy chip feature.
The MAINTAINERS conflict was merely overlapping changes, one
change updated all the wireless web site URLs and the other
changed some GIT trees to be Johannes's instead of John's.
Signed-off-by: David S. Miller <davem@davemloft.net>
As soon as hardware is notified of a transmit, we no longer can assume
skb can be dereferenced, as TX completion might have freed the packet.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Permanent MAC is wrongly supplied in create iface command. Call the
command with no MAC address and then MAC address should be later queried
and applied.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CUST_SCRATCHPAD_CSR register is used for marking if FW cleanup is
needed. This is used in a crash kernel scenario. Do no use this register as
it is not available for some functions. Instead, always issue an FLR when
a function is probed *except* when VFs are preset (enabled in the previous
PF load).
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting the PCI MRRS to a value of 4096 (overriding the system decided
value) had provided perf improvement in TX.
But, IBM has provided feedback that on POWER platforms, this value is set
by the system firmware, and drivers modifying this value can cause
unpredictable results (like EEH errors.) So, backing off this change.
On POWER7 platforms most slots, it seems, do get a MRRS of 4096.
This patch reverts the following commit:
"be2net: Modified PCI MaxReadReq size to 4096 bytes"
commit 5a56eb10ba.
Suggested-by: Brian King <bjking1@us.ibm.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- get rid of 2 unused arguments to the routine and some unused code
- don't use the term "vlan_tag" in place of "vid" as they are different
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
be_vid_config() is called from be_setup() to replay config cmds after
a card reset. Skip calling it when no vlans are configured.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add ocrdma hardware driver for Emulex IB-over-Ethernet adapters
- Add generic and mlx4 support for "raw" QPs: allow suitably privileged
applications to send and receive arbitrary packets directly to/from
the hardware
- Add "doorbell drop" handling to the cxgb4 driver
- A fairly large batch of qib hardware driver changes
- A few fixes for lockdep-detected issues
- A few other miscellaneous fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=yWfr
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA changes from Roland Dreier:
- Add ocrdma hardware driver for Emulex IB-over-Ethernet adapters
- Add generic and mlx4 support for "raw" QPs: allow suitably privileged
applications to send and receive arbitrary packets directly to/from
the hardware
- Add "doorbell drop" handling to the cxgb4 driver
- A fairly large batch of qib hardware driver changes
- A few fixes for lockdep-detected issues
- A few other miscellaneous fixes and cleanups
Fix up trivial conflict in drivers/net/ethernet/emulex/benet/be.h.
* tag 'rdma-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (53 commits)
RDMA/cxgb4: Include vmalloc.h for vmalloc and vfree
IB/mlx4: Fix mlx4_ib_add() error flow
IB/core: Fix IB_SA_COMP_MASK macro
IB/iser: Fix error flow in iser ep connection establishment
IB/mlx4: Increase the number of vectors (EQs) available for ULPs
RDMA/cxgb4: Add query_qp support
RDMA/cxgb4: Remove kfifo usage
RDMA/cxgb4: Use vmalloc() for debugfs QP dump
RDMA/cxgb4: DB Drop Recovery for RDMA and LLD queues
RDMA/cxgb4: Disable interrupts in c4iw_ev_dispatch()
RDMA/cxgb4: Add DB Overflow Avoidance
RDMA/cxgb4: Add debugfs RDMA memory stats
cxgb4: DB Drop Recovery for RDMA and LLD queues
cxgb4: Common platform specific changes for DB Drop Recovery
cxgb4: Detect DB FULL events and notify RDMA ULD
RDMA/cxgb4: Drop peer_abort when no endpoint found
RDMA/cxgb4: Always wake up waiters in c4iw_peer_abort_intr()
mlx4_core: Change bitmap allocator to work in round-robin fashion
RDMA/nes: Don't call event handler if pointer is NULL
RDMA/nes: Fix for the ORD value of the connecting peer
...
Patch re-spin.
Incorporated review comments by Ben Hutchings.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling pci_disable_sriov() while VFs are assigned to VMs causes
kernel panic. This patch uses PCI_DEV_FLAGS_ASSIGNED bit state of the
VF's pci_dev to avoid this. Also, the unconditional function reset cmd
issued on a PF probe can delete the VF configuration for the
previously enabled VFs. A scratchpad register is now used to issue a
function reset only when needed (i.e., in a crash dump scenario.)
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Increase MSI-X vectors by 5 for RoCE traffic.
- Add macro to check roce support on a device.
- Add device-specific doorbell and MSI-X vector fields shared with NIC
functionality.
- Provide RoCE driver registration and deregistration functions.
- Add support functions which will be invoked on adapter add/remove
and port up/down events.
- Traverse through the list of adapters to invoke callback functions.
Signed-off-by: Parav Pandit <parav.pandit@emulex.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Roland Dreier <roland@purestorage.com>
- Add generic function to issue mailbox cmd on MQ as export function.
- RoCE driver will use this before it setups its own MQ.
Signed-off-by: Parav Pandit <parav.pandit@emulex.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Roland Dreier <roland@purestorage.com>
An EEH error can cause the FW to trigger a flash debug dump.
Resetting the card while flash dump is in progress can cause it not to recover.
Wait for it to finish before letting EEH flow to reset the card.
Signed-off-by: Sathya Perla <Sathya.Perla@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sarveshwar Bandi <Sarveshwar.Bandi@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suggested-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This renders the interface view somewhat inconsistent from the Host OS POV
considering the rest of the interfaces are showing their respective speeds
based on the bandwidth assigned to them.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
logical speed returned by link_status_query needs to be multiplied by 10.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Skip flashing a FW component if that component is not present in a
particular FW UFI image.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MCC Response CQEs are processed as part of NAPI poll routine and
also synchronously. If MCC completions are consumed by NAPI poll
routine, wrong status is returned to synchronously waiting routine.
Fix this by getting status of MCC command from command response
instead of response CQEs.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix port num sent in command to get stats. Also skip unnecessary
parsing of stats for Lancer.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EQ is getting armed wrongly in INTx mode as INTx interrupt is taking
some time to deassert. This can cause another interrupt while NAPI is
scheduled and scheduling a NAPI in interrupt does not take effect.
This causes interrupt to be missed and traffic stalls. Fixing this by
preventing wrong arming of EQ.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lancer does not support DDR self test. Fix ethtool self test by
skipping this test for Lancer.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase time given by driver to adapter for completing FW download
to 30 seconds. Also return correct status when FW download times out.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN and multicast hardware filters are limited and can get
exhausted in adapters with many PCI functions. If setting
a VLAN or multicast filter fails due to lack of sufficient
hardware resources, these packets get dropped. Fix this by
switching to VLAN or multicast promiscous mode so that these
packets are not dropped.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool get settings was not displaying all the settings correctly.
use the get_phy_info to get more information about the PHY to fix this.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In flex10 mode the number of vlan slots supported is halved.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will prevent double free in some cases where be_clear() is called
for cleanup when be_setup() fails half-way.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a part of be_close(), instead of waiting for a max of 200ms for each TXQ,
wait for a total of 200ms for completions from all TXQs to arrive.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EEH recovery involves ring cleanup and re-creation. The worker
thread must not run during EEH cleanup/resume.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: Fixed up the bad typecasting pointed out by David...
In the current design 8 TXQs are serviced by 1 EQ, while each RSS queue
is serviced by a separate EQ. This is being changed as follows:
- Upto 8 EQs will be used (based on the availabilty of msix vectors).
Each EQ will handle 1 RSS and 1 TX ring. The default non-RSS RX queue and
MCC queue are handled by the last EQ.
- On cards which provide support, upto 8 RSS rings will be used, instead
of the current limit of 4.
The new design allows spreading the TX multi-queue completion processing
across multiple CPUs unlike the previous design.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VFs use get mac list command to get their mac address. The format of
this command has changed. Update driver to use the new format.
Signed-off-by: Mammatha Edhala <mammatha.edhala@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Version number in query link status command is getting overwritten in
be_wrb_cmd_hdr_prepare() routine. Move the initialization to fix this
issue. Also initialize the domain field.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The parameters for ETHTOOL_FLASHDEV include a filename, which ought to
be null-terminated. Currently the only driver that implements
ethtool_ops::flash_device attempts to add a null terminator if
necessary, but does it wrongly. Do it in the ethtool core instead.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also rename a few counters appropritely and delete 2 counters that are not
implemented in HW.
vlan_mismatch_drops does not exist in BE3 and is accounted for in
address_mismatch_drops. Do the same thing for BE2 and Lancer.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocation of 64 bytes in skb headroom is not enough if we have to pull
ethernet + ipv6 + tcp headers, and/or extra tunneling header.
Its currently not noticed because netdev_alloc_skb_ip_align(64) give us
more room, thanks to power-of-two kmalloc() roundups.
Make sure we ask for 128 bytes so that side effects of upcoming patches
from Ian Campbell dont decrease benet rx performance, because of extra
skb head reallocations.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ian Campbell <Ian.Campbell@citrix.com>
Cc: Vasundhara Volam <vasundhara.volam@emulex.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently RSS rings are not created in a multi-channel config.
RSS rings can be created on one (out of four) interfaces per port in a
multi-channel config. Doing this insulates the driver from a FW bug wherin
multi-channel config is wrongly reported even when not enabled. This also
helps performance in a multi-channel config, as one interface per port gets
RSS rings.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
More drivers where net_device_ops should be const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
be2net gets an async link status notification from the FW when it creates
an MCC queue. There are some cases in which this gratuitous notification
is not received from FW. To cover this explicitly query the link status
in be_open().
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) fix be_vlan_add/rem_vid to return proper status
2) perform appropriate housekeeping if firmware command succeeds.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lancer does not have HW registers to indicate the EQ causing the INTx
interrupt. As a result EQE entries of one EQ may be consumed when interrupt
is caused by another EQ. Fix this by arming CQs at the end of NAPI poll
routine to regenerate the EQEs.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- use adapter->num_vfs (and not the module param) to store the actual
number of vfs created. Use the same variable to reflect SRIOV
enable/disable state. So, drop the adapter->sriov_enabled field.
- use for_all_vfs() macro in VF configuration code
- drop the "vf_" prefix for the fields of be_vf_cfg; the prefix is
redundant and removing it helps reduce line wrap
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool "-g" option is supposed to report the max queue length and
user modified queue length for RX and TX queues. be2net doesn't support
user modification of queue lengths. So, the correct values for these
would be the max numbers.
be2net incorrectly reports the queue used values for these fields.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
disable Tx vlan offloading in certain cases.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
update pmem_fifo_overflow_drop, rx_priority_pause_frames counters.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let caller know the result of adding/removing vlan id to/from vlan
filter.
In some drivers I make those functions to just return 0. But in those
where there is able to see if hw setup went correctly, return value is
set appropriately.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When non power of two MSIX vectors are given to driver, some RX queues
are not utilized. Program RSS table in such a way that all queues
are utilized.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new hash key gives better distribution of packets across RX
queues.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detect error in Lancer by polling a HW register and
recover from this error if it is recoverable.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When TX queues are created again after error recovery,
netif_set_real_num_tx_queues() is invoked to update number of real
TX queues created. rtnl lock needs to be held when invoking this routine.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SR-IOV implementation is Lancer has changed in following ways -
1)PF driver assigns one MAC addresses for VF using COMMON_SET_IFACE_MAC_LIST.
2)VF driver queries its MAC address using COMMON_GET_IFACE_MAC_LIST command
and assigns it to its interface.
Signed-off-by: Mammatha Edhala <mammatha.edhala@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use V1 version of query link status command for Lancer.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To enable VLAN promiscous mode, the HW interface should be created
with VLAN promiscous capability in Lancer. Add this capability during
creation of the HW interface.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implemented eeprom dump using ethtool feature for Lancer.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement register dump using ethtool for Lancer.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lancer uses V1 version of TXQ create. This command needs interface
id for TX queue creation. Rearrange code such that tx queue create
is after interface create. As TXQ create is now called after MCC
ring create use MCC instead of MBOX.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A FW cmd timeout (with a sufficiently large timeout value in the
order of tens of seconds) indicates an unresponsive FW. In this state
issuing further cmds and waiting for a completion will only stall the process.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we're spamming error messages each time a FW cmd call is made
while in EEH/UE error state. One log msg on error detection is enough.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize if_handle, vf_if_handle and vf_pmac_id with "-1" so that in
failure cases when be_clear() is called, we can skip over
if_destroy/pmac_del cmds if they have not been created.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per the mention made by Ben Hutchings that strlcpy is now the preferred
string copy routine for a .get_drvinfo routine, do a bit of floor
sweeping and convert some of the as-yet unconverted ethernet drivers to
it.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
Add code to detect UE in case of Lancer.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indicate to HW that the CQ is cleaned up before posting new RX buffers.
This prevents the HW to go into CQ full error condition.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If user tries to disable multicast promiscous mode, the adapter remains
in this mode as resetting the multicast promiscous mode was missing
in RX filter command. Fixed this.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use cpu_to_le32() for mcast_num field in RX filter command as this
field is of type u32.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device.h header was including module.h, making it present for
most of these drivers. But we want to clean that up. Call out the
include of module.h in the modular network drivers.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Allow for MAC Address change of VF(SR-IOV case) on the fly- First add and then
delete MAC Address to allow for 'out of pool' errors.
When MAC Addr configured from a VM, the MAC on the NIC will aleady have
the supplied MAC,so just copy the supplied MAC to the netdev structure
before returning success to the stack
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moved the .sge. field's population inside be_cmd_hdr_prepare.
Populating wrb->tag0 and tag1 inside be_cmd_hdr_prepare
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the HW is in multi-channel mode based on the skew/IPL, there are
4 functions per port and so not enough resources to create multiple
RX/TX rings for each function.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple TXQ support is partially broken in BE2. It is fully
supported BE3 onwards and in Lancer.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the code for VF setup/teardown done by a PF (if_create,
mac_add_config, link_status_query etc) is scattered; this patch
refactors this code into be_vf_setup() and be_vf_clear(). The
if_create/if_destroy/mac_addr_query cmds are now called after the MCCQ
is created; so these cmds are now modified to use the MCCQ instead of
MBOX.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a card is reset due to EEH error recovery or due to a suspend,
rx-mode config (promisc/mc) is not being sent to the FW. be_setup() is
called in these flows and is the best place for such config/re-config
cmds. Hence include rx-mode, vlan and flow-control config in
be_setup().
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To ease skb->truesize sanitization, its better to be able to localize
all references to skb frags size.
Define accessors : skb_frag_size() to fetch frag size, and
skb_frag_size_{set|add|sub}() to manipulate it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix skb truesize underestimations of this driver.
Each frag truesize is exactly rx_frag_size bytes. (2048 bytes per
default)
A driver should not use "sizeof(struct sk_buff)" at all.
Signed-off-by: Eric Dumazet <eric.dumazet>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also changing it's frequency to once every 64s instead of existing 32s as
it was shown to affect performance
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was manifesting as a crash when FAT Dump extraction was attempted on a PPC machine.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was showing up as junk value on PPC /Big endian machines since
it was marked as a byte.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 60s delay before timeout on polling Bit 31 so that FAT dump can
complete when reset occurs.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fix provides a newly flashed FW version (appended, in braces)
along with the currently running FW version via ethtool. The newly
flashed version runs only after a system reset.
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-posting with subject fixed!
Multicast programming has been broken since commit 5b8821b7. Setting the
MULTICAST flag while sending the cmd to the FW was missing. Fixed this.
Also fixed-up some indentation in the adjacent lines.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flashing some of the PHYs can take longer thus increasing the total flash
update time to a max of 40s.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx_drops_no_frags HW counter for RSS rings is 16bits in HW and can
wraparound often. Maintain a 32-bit accumulator in the driver to prevent
frequent wraparound.
Also, incorporated Eric's feedback to use ACCESS_ONCE() for the accumulator
write.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of adapter->pcicfg and its use. Use pci_config_read/write_dword()
instead.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a possibility of be_post_rx_frags() being called simultaneously from
both be_worker() (when rx_post_starved) and be_poll_rx() (when rxq->used is 0).
This can be avoided by posting rx buffers only when some completions have been
reaped.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error comes from commit ac124ff973
(be2net: cleanup and refactor stats code)
ERROR: "__udivdi3" [drivers/net/benet/be2net.ko] undefined!
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moves the Emulex driver into drivers/net/ethernet/emulex/ and
make the necessary Kconfig and Makefile changes.
CC: Sathya Perla <sathya.perla@emulex.com>
CC: Subbu Seetharaman <subbu.seetharaman@emulex.com>
CC: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
