Fields t_bidi_data_sg and t_bidi_data_nents are set only in the presence
of BIDI commands. This means that the underlying code (for example TCMU)
cannot inspect them when the SCSI command is not a BIDI one.
Ensure the code always initializes these fields with the given values,
even when the SCSI command is not a BIDI one. Set t_bidi_data_sg to
sgl_bidi (which should be NULL for non-BIDI commands) and
t_bidi_data_nents to sgl_bidi_count (which should be 0 for non-BIDI
commands). This allows the underlying code to use these fields
unconditionally.
Signed-off-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Vangelis Koukis <vkoukis@arrikto.com>
Reviewed-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Field shost->max_cmd_len is used to inform Linux / the SCSI midlayer of
the maximum CDB size an LLD is capable of handling. Set this field to
SCSI_MAX_VARLEN_CDB_SIZE for target, to enable support for
variable-sized CDBs (0x7E).
Also remove the definition of TL_SCSI_MAX_CMD_LEN since it is now
redundant.
Signed-off-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Vangelis Koukis <vkoukis@arrikto.com>
Reviewed-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Some SCSI commands (for example the TEST UNIT READY command) do not
carry data and so data_direction is DMA_NONE. Patch TCMU to not print a
warning message about unknown data direction, when it is DMA_NONE.
Signed-off-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Vangelis Koukis <vkoukis@arrikto.com>
Reviewed-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Drivers may override the WCE flag, in which case the DPOFUA flag in
MODE SENSE might differ from the check used to reject invalid FUA
bits in sbc_check_dpofua. Also now that we reject invalid FUA
bits early there is no need to duplicate the same buggy check
down in the fileio code.
As the DPOFUA flag controls th support for FUA bits on read and
write commands as well as DPO key off all the checks off a single
helper, and deprecate the emulate_dpo and emulate_fua_read attributs.
This fixes various failures in the libiscsi testsuite.
Personally I'd prefer to also remove the emulate_fua_write attribute
as there is no good reason to disable it, but I'll leave that for
a separate discussion.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Support for markers is currently broken because of a bug in
iscsi_enforce_integrity_rules(): the "IFMarkInt_Reject" and
"OFMarkInt_Reject" variables are always equal to 1 in
iscsi_enforce_integrity_rules().
Moreover, fixed interval markers keys (IFMarker, OFMarker, IFMarkInt
and OFMarkInt) are obsolete according to iSCSI RFC 7143:
>From http://tools.ietf.org/html/rfc7143#section-13.25:
13.25. Obsoleted Keys
This document obsoletes the following keys defined in [RFC3720]:
IFMarker, OFMarker, OFMarkInt, and IFMarkInt. However, iSCSI
implementations compliant to this document may still receive these
obsoleted keys -- i.e., in a responder role -- in a text negotiation.
When an IFMarker or OFMarker key is received, a compliant iSCSI
implementation SHOULD respond with the constant "Reject" value. The
implementation MAY alternatively respond with a "No" value.
However, the implementation MUST NOT respond with a "NotUnderstood"
value for either of these keys.
When an IFMarkInt or OFMarkInt key is received, a compliant iSCSI
implementation MUST respond with the constant "Reject" value. The
implementation MUST NOT respond with a "NotUnderstood" value for
either of these keys.
This patch disables markers by turning the corresponding parameters to
read-only. The default value of IFMarker and OFMarker remains "No" but
the user cannot change it to "Yes" anymore. The new value of IFMarkInt
and OFMarkInt is "Reject".
(Drop left-over iscsi_get_value_from_number_range + make configfs
parameters attrs R/W nops - nab)
Signed-off-by: Christophe Vu-Brugier <cvubrugier@fastmail.fm>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fix map/unmap consistency and get rid of a redundant
local variable psg.
Reported-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The reason this bounce buffer exists is to allow code
reuse between rd_mcp and fileio in DIF mode. But the fact is,
that this bounce is really not needed at all, we can simply call
sbc_dif_verify on cmd->t_prot_sg and use it for file IO.
This also removes fd_do_prot_rw as fd_do_rw was generalised
to receive file pointer, block size (8 bytes for DIF data) and
total data length.
(Fix apply breakage from commit c836777 - nab)
Tested-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of providing DIF verify routines for read/write
that are almost identical and conditionally copy protection
information, just let the caller do the right thing.
Have a single sbc_dif_verify that handles an sgl (that
does NOT copy any data) and a protection information copy
routine used by rd_mcp and fileio backend.
In the WRITE case, call sbc_dif_verify with cmd->t_prot_sg
and then do the copy from it to local sgl (assuming the verify
succeeded of course). In the READ case, call sbc_dif_verify
with the local sgl and if it succeeds, copy it to t_prot_sg (or
not if we are stripping it).
(Fix apply breakage from commit c836777 - nab)
Tested-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
It seems like we only care if a transport is passthrough or not. Convert
transport_type to a flags field and replace TRANSPORT_PLUGIN_* with a
flag, TRANSPORT_FLAG_PASSTHROUGH.
Signed-off-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Aside from whether they handle BIDI ops or not, parsing of the CDB by
kernel and user SCSI passthrough modules should be identical. Move this
into a new passthrough_parse_cdb() and call it from tcm-pscsi and tcm-user.
Reported-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
After much discussion, give up on only passing a subset of SCSI commands
to userspace and pass them all. Based on what pscsi is doing, make sure
to set SCF_SCSI_DATA_CDB for I/O ops, and define attributes identical to
pscsi.
Make hw_block_size configurable via dev param.
Remove mention of command filtering from tcmu-design.txt.
Signed-off-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
See https://bugzilla.redhat.com/show_bug.cgi?id=1025672
We need to put() the reference to the scsi host that we got in
pscsi_configure_device(). In VIRTUAL_HOST mode it is associated with
the dev_virt, not the hba_virt.
Signed-off-by: Andy Grover <agrover@redhat.com>
Cc: stable@vger.kernel.org # 2.6.38+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
There is just one configfs subsystem in the target code, so we might as
well add two helpers to reference / unreference it from the core code
instead of passing pointers to it around.
This fixes a regression introduced for v4.1-rc1 with commit 9ac8928e6,
where configfs_depend_item() callers using se_tpg_tfo->tf_subsys would
fail, because the assignment from the original target_core_subsystem[]
is no longer happening at target_register_template() time.
(Fix target_core_exit_configfs pointer dereference - Sagi)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
All of these files were only building on non-x86 because of
the indirect of inclusion of vmalloc.h by, of all things,
"net/inet_hashtables.h"
None of this got caught during build testing, because on x86
there is an implicit vmalloc.h include via on of the arch asm/
headers.
This fixes all of these
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once upon a time, iscsit_get_tpg() was using an un-interruptible
lock. The signal_pending() usage was a check to allow userspace
to break out of the operation with SIGINT.
AFAICT, there's no reason why this is necessary anymore, and as
reported by Alexey can be potentially dangerous. Also, go ahead
and drop the other two problematic cases within iscsit_access_np()
and sbc_compare_and_write() as well.
Found by Linux Driver Verification project (linuxtesting.org).
Reported-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Code like " &= ~CMD_T_BUSY | ..." only clears CMD_T_BUSY but not
the other flag. Modify these statements such that both flags are
cleared.
(Fix fuzz for target_write_prot_action code in mainline - nab)
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The function transport_complete_qf() must call either
queue_data_in() or queue_status() but not both.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
TCMU requires more work to correctly handle both user handlers that want
all SCSI commands (pass_level=0) for a se_device, and also handlers that
just want I/O commands and let the others be emulated by the kernel
(pass_level=1). Only support the latter for now.
For full passthrough, we will need to support a second se_subsystem_api
template, due to configfs attributes being different between the two modes.
Thus pass_level is extraneous, and we can remove it.
The ABI break for TCMU v2 is already applied for this release, so it's
best to do this now to avoid another ABI break in the future.
Signed-off-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a missing kfree for sess->sess_ops memory upon
transport_init_session() failure.
Signed-off-by: Evgenii Lepikhin <johnlepikhin@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"Lots of activity in target land the last months.
The highlights include:
- Convert fabric drivers tree-wide to target_register_template() (hch
+ bart)
- iser-target hardening fixes + v1.0 improvements (sagi)
- Convert iscsi_thread_set usage to kthread.h + kill
iscsi_target_tq.c (sagi + nab)
- Add support for T10-PI WRITE_STRIP + READ_INSERT operation (mkp +
sagi + nab)
- DIF fixes for CONFIG_DEBUG_SG=y + UNMAP file emulation (akinobu +
sagi + mkp)
- Extended TCMU ABI v2 for future BIDI + DIF support (andy + ilias)
- Fix COMPARE_AND_WRITE handling for NO_ALLLOC drivers (hch + nab)
Thanks to everyone who contributed this round with new features,
bug-reports, fixes, cleanups and improvements.
Looking forward, it's currently shaping up to be a busy v4.2 as well"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (69 commits)
target: Put TCMU under a new config option
target: Version 2 of TCMU ABI
target: fix tcm_mod_builder.py
target/file: Fix UNMAP with DIF protection support
target/file: Fix SG table for prot_buf initialization
target/file: Fix BUG() when CONFIG_DEBUG_SG=y and DIF protection enabled
target: Make core_tmr_abort_task() skip TMFs
target/sbc: Update sbc_dif_generate pr_debug output
target/sbc: Make internal DIF emulation honor ->prot_checks
target/sbc: Return INVALID_CDB_FIELD if DIF + sess_prot_type disabled
target: Ensure sess_prot_type is saved across session restart
target/rd: Don't pass incomplete scatterlist entries to sbc_dif_verify_*
target: Remove the unused flag SCF_ACK_KREF
target: Fix two sparse warnings
target: Fix COMPARE_AND_WRITE with SG_TO_MEM_NOALLOC handling
target: simplify the target template registration API
target: simplify target_xcopy_init_pt_lun
target: remove the unused SCF_CMD_XCOPY_PASSTHROUGH flag
target/rd: reduce code duplication in rd_execute_rw()
tcm_loop: fixup tpgt string to integer conversion
...
Conceptually version 2 should be viewed as an entirely new, incompatible
version of TCMU, so emphasize this by changing the config option and
Kconfig text.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The initial version of TCMU (in 3.18) does not properly handle
bidirectional SCSI commands -- those with both an in and out buffer. In
looking to fix this it also became clear that TCMU's support for adding
new types of entries (opcodes) to the command ring was broken. We need
to fix this now, so that future issues can be handled properly by adding
new opcodes.
We make the most of this ABI break by enabling bidi cmd handling within
TCMP_OP_CMD opcode. Add an iov_bidi_cnt field to tcmu_cmd_entry.req.
This enables TCMU to describe bidi commands, but further kernel work is
needed for full bidi support.
Enlarge tcmu_cmd_entry_hdr by 32 bits by pulling in cmd_id and __pad1. Turn
__pad1 into two 8 bit flags fields, for kernel-set and userspace-set flags,
"kflags" and "uflags" respectively.
Update version fields so userspace can tell the interface is changed.
Update tcmu-design.txt with details of how new stuff works:
- Specify an additional requirement for userspace to set UNKNOWN_OP
(bit 0) in hdr.uflags for unknown/unhandled opcodes.
- Define how Data-In and Data-Out fields are described in req.iov[]
Changed in v2:
- Change name of SKIPPED bit to UNKNOWN bit
- PAD op does not set the bit any more
- Change len_op helper functions to take just len_op, not the whole struct
- Change version to 2 in missed spots, and use defines
- Add 16 unused bytes to cmd_entry.req, in case additional SAM cmd
parameters need to be included
- Add iov_dif_cnt field to specify buffers used for DIF info in iov[]
- Rearrange fields to naturally align cdb_off
- Handle if userspace sets UNKNOWN_OP by indicating failure of the cmd
- Wrap some overly long UPDATE_HEAD lines
(Add missing req.iov_bidi_cnt + req.iov_dif_cnt zeroing - Ilias)
Signed-off-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When UNMAP command is issued with DIF protection support enabled,
the protection info for the unmapped region is remain unchanged.
So READ command for the region causes data integrity failure.
This fixes it by invalidating protection info for the unmapped region
by filling with 0xff pattern. This change also adds helper function
fd_do_prot_fill() in order to reduce code duplication with existing
fd_format_prot().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In fd_do_prot_rw(), it allocates prot_buf which is used to copy from
se_cmd->t_prot_sg by sbc_dif_copy_prot(). The SG table for prot_buf
is also initialized by allocating 'se_cmd->t_prot_nents' entries of
scatterlist and setting the data length of each entry to PAGE_SIZE
at most.
However if se_cmd->t_prot_sg contains a clustered entry (i.e.
sg->length > PAGE_SIZE), the SG table for prot_buf can't be
initialized correctly and sbc_dif_copy_prot() can't copy to prot_buf.
(This actually happened with TCM loopback fabric module)
As prot_buf is allocated by kzalloc() and it's physically contiguous,
we only need a single scatterlist entry.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When CONFIG_DEBUG_SG=y and DIF protection support enabled, kernel
BUG()s are triggered due to the following two issues:
1) prot_sg is not initialized by sg_init_table().
When CONFIG_DEBUG_SG=y, scatterlist helpers check sg entry has a
correct magic value.
2) vmalloc'ed buffer is passed to sg_set_buf().
sg_set_buf() uses virt_to_page() to convert virtual address to struct
page, but it doesn't work with vmalloc address. vmalloc_to_page()
should be used instead. As prot_buf isn't usually too large, so
fix it by allocating prot_buf by kmalloc instead of vmalloc.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The loop in core_tmr_abort_task() iterates over sess_cmd_list.
That list is a list of regular commands and task management
functions (TMFs). Skip TMFs in this loop instead of letting
the target drivers filter out TMFs in their get_task_tag()
callback function.
(Drop bogus check removal in tcm_qla2xxx_get_task_tag - nab)
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: <qla2xxx-upstream@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that sbc_dif_generate can also be called for READ_INSERT, update
the debugging message accordingly.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The internal DIF emulation was not honoring se_cmd->prot_checks for
the WRPROTECT/RDPROTECT == 0x3 case, so sbc_dif_v1_verify() has been
updated to follow which checks have been calculated based on
WRPROTECT/RDPROTECT in sbc_set_prot_op_checks().
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In sbc_check_prot(), if PROTECT is non-zero for a backend device with
DIF disabled, and sess_prot_type is not set go ahead and return
INVALID_CDB_FIELD.
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The following incremental patch saves the current sess_prot_type into
se_node_acl, and will always reset sess_prot_type if a previous saved
value exists. So the PI setting for the fabric's session with backend
devices not supporting PI is persistent across session restart.
(Fix se_node_acl dereference for discovery sessions - DanCarpenter)
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The scatterlist for protection information which is passed to
sbc_dif_verify_read() or sbc_dif_verify_write() requires that
neighboring scatterlist entries are contiguous or chained so that they
can be iterated by sg_next().
However, the protection information for RD-MCP backends could be located
in the multiple scatterlist arrays when the ramdisk space is too large.
So if the read/write request straddles this boundary, sbc_dif_verify_read()
or sbc_dif_verify_write() can't iterate all scatterlist entries.
This problem can be fixed by chaining protection information scatterlist
at creation time. For the architectures which don't support sg chaining
(i.e. !CONFIG_ARCH_HAS_SG_CHAIN), fix it by allocating temporary
scatterlist if needed.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Sagi Grimberg <sagig@dev.mellanox.co.il>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: target-devel@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The flag SCF_ACK_KREF is only set but never tested. Hence remove
this flag.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Avoid that sparse complains about context imbalances.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug for COMPARE_AND_WRITE handling with
fabrics using SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC.
It adds the missing allocation for cmd->t_bidi_data_sg within
transport_generic_new_cmd() that is used by COMPARE_AND_WRITE
for the initial READ payload, even if the fabric is already
providing a pre-allocated buffer for cmd->t_data_sg.
Also, fix zero-length COMPARE_AND_WRITE handling within the
compare_and_write_callback() and target_complete_ok_work()
to queue the response, skipping the initial READ.
This fixes COMPARE_AND_WRITE emulation with loopback, vhost,
and xen-backend fabric drivers using SG_TO_MEM_NOALLOC.
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of calling target_fabric_configfs_init() +
target_fabric_configfs_register() / target_fabric_configfs_deregister()
target_fabric_configfs_free() from every target driver, rewrite the API
so that we have simple register/unregister functions that operate on
a const operations vector.
This patch also fixes a memory leak in several target drivers. Several
target drivers namely called target_fabric_configfs_deregister()
without calling target_fabric_configfs_free().
A large part of this patch is based on earlier changes from
Bart Van Assche <bart.vanassche@sandisk.com>.
(v2: Add a new TF_CIT_SETUP_DRV macro so that the core configfs code
can declare attributes as either core only or for drivers)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This fixes a oops due to a double list add when adding a reject PDU for
iscsit_allocate_iovecs allocation failures. The cmd has already been
added to the conn_cmd_list in iscsit_setup_scsi_cmd, so this has us call
iscsit_reject_cmd.
Note that for ERL0 the reject PDU is not actually sent, so this patch
is not completely tested. Just verified we do not oops. The problem is the
add reject functions return -1 which is returned all the way up to
iscsi_target_rx_thread which for ERL0 will drop the connection.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Drop unused argument & return value and consolidate a duplicate assignment.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Factor out code duplication in rd_execute_rw() into a helper function
rd_do_prot_rw(). This change is required to minimize the forthcoming
fix in rd_do_prot_rw().
(Fix up v4.1 for-next fuzz - nab)
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Sagi Grimberg <sagig@dev.mellanox.co.il>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: target-devel@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Currently, for example, mkdir "tpgt_xyz" doesn't return error.
mkdir /sys/kernel/config/target/loopback/naa.60014055f195952b/tpgt_xyz
Replace obsoleted simple_strtoul with kstrtoul and check the conversion.
Signed-off-by: Ming Lin <mlin@kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch updates iscsi/iser-target to add a new fabric_prot_type
TPG attribute for iser-target, used for controlling LLD level
protection into LIO when the backend device does not support T10-PI.
This is required for ib_isert to enable WRITE_STRIP + READ_INSERT
hardware offloads.
It's disabled by default and controls which se_sesion->sess_prot_type
are set at iscsi_target_locate_portal() session registration time.
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Martin Petersen <martin.petersen@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch updates loopback to add a new fabric_prot_type TPG attribute,
used for controlling LLD level protection into LIO when the backend
device does not support T10-PI.
Also, go ahead and set DIN_PASS + DOUT_PASS so target-core knows that
it will be doing any WRITE_STRIP and READ_INSERT operations.
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Make sure that RAMDISK only attempts to use backend DIF emulation
when it's actually enabled at device level.
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Make sure that IBLOCK only attempts to use backend DIF emulation
when it's actually enabled at device level.
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Make sure that FILEIO only attempts to use backend DIF emulation
when it's actually enabled at device level.
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds READ_INSERT support in target_read_prot_action() that
invokes sbc_dif_generate() when LIO is responsible for generating the
outgoing T10-PI.
Required for supporting fabrics that exchange protection information,
and would like to function with un-protected devices.
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch moves the existing target_complete_ok_work() check for
cmd->prot_op into it's own function, so it's easier to add future
support for READ INSERT.
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds WRITE_STRIP support in target_write_prot_action() that
invokes sbc_dif_verify_write() for checking T10-PI metadata before
submitting the I/O to a backend driver.
Upon verify failure, the specific sense code is propigated up the
failure path up to transport_generic_request_failure().
Also, update sbc_dif_verify_write() to only perform the subsequent
protection metadata copy when a valid *sg is passed.
(Use ilog2 instead of division and unlikely for pi_err - Sagi)
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch moves the existing target_execute_cmd() check for
cmd->prot_op into it's own function, so it's easier to add
future support for WRITE STRIP.
(Use better target_write_prot_action name - Sagi)
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch updates standard INQUIRY, INQUIRY EVPD=0x86, READ_CAPACITY_16
and control mode pages to use se_sess->sess_prot_type when determing which
type of T10-PI related feature bits can be exposed.
This is required for fabric sessions supporting T10-PI metadata to
backend devices that don't have protection enabled.
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Doug Gilbert <dgilbert@interlog.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a new target_core_fabric_ops callback for allowing fabric
drivers to expose a TPG attribute for signaling when a T10-PI protected
fabric wants to function with an un-protected device without T10-PI.
This specifically is to allow LIO to perform WRITE_STRIP + READ_INSERT
operations when functioning with non T10-PI enabled devices, seperate
from any available hw offloads the fabric supports.
This is done using a new se_sess->sess_prot_type that is set at fabric
session creation time based upon the TPG attribute. It currently cannot
be changed for individual sessions after initial creation.
Also, update existing target_core_sbc.c code to honor sess_prot_type when
setting up cmd->prot_op + cmd->prot_type assignments.
(Add unlikely and !! boolean conversion in sbc_check_prot - Sagi)
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Doug Gilbert <dgilbert@interlog.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes existing DIF emulation to check the command descriptor's
prot_type, instead of what the backend device is exposing in pi_prot_type.
Since this value is already set in sbc_check_prot(), go ahead and use it to
allow protected fabrics to function with unprotected devices.
Reviewed-by: Martin Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
"The domainname can be specified as either a DNS host name, a
dotted-decimal IPv4 address, or a bracketed IPv6 address as specified
in [RFC2732]."
See https://bugzilla.redhat.com/show_bug.cgi?id=1206868
Reported-by: Kyle Brantley <kyle@averageurl.com>
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Before 4.0, reading attrib/emulate_fua_write has returned 1. Saved
configs created on a pre-4.0 kernel will try to write that back when
restoring LIO configuration. This should succeed with no effect,
and issue a warning.
See https://bugzilla.redhat.com/show_bug.cgi?id=1206184
Reported-by: Yanko Kaneti <yaneti@declera.com>
Reported-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We should not declare extrnal .c symbols in C files to make sure they
match the actual prototype, and sparse correctly warns about this.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fix AllRegistrants reservations in register_and_move() function where
the code didn't handle all of the registered devices as reservation
holders, resulting in the wrong warning message being displayed.
At the same time, introduce a helper function named
'is_reservation_holder()' that properly checks if a device is a
reservation holder, taking into account the reservation type. This
function cleans up the code and improves readability.
Signed-off-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Vangelis Koukis <vkoukis@arrikto.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that iscsi_conn allocates new [rx,tx] threads using kthread.h
primitives on the fly, and kthread_stop() is called directly during
connection shutdown, it's time to go ahead and drop iscsi_target_tq.c
legacy code.
The use of multiple struct completion in iscsi_activate_thread_set()
has been proven to cause issues during repeated iser login/logout.
Tested-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Slava Shwartsman <valyushash@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts iscsi-target code to use modern kthread.h API
callers for creating RX/TX threads for each new iscsi_conn descriptor,
and releasing associated RX/TX threads during connection shutdown.
This is done using iscsit_start_kthreads() -> kthread_run() to start
new kthreads from within iscsi_post_login_handler(), and invoking
kthread_stop() from existing iscsit_close_connection() code.
Also, convert iscsit_logout_post_handler_closesession() code to use
cmpxchg when determing when iscsit_cause_connection_reinstatement()
needs to sleep waiting for completion.
Reported-by: Sagi Grimberg <sagig@mellanox.com>
Tested-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Slava Shwartsman <valyushash@gmail.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
type T;
identifier f;
@@
static T f (...) { ... }
@@
identifier r.f;
declarer name EXPORT_SYMBOL;
@@
-EXPORT_SYMBOL(f);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts the fabric module autoload failures from
pr_err to pr_debug in target_core_register_fabric() code, to
reduce the amount of noise during normal operation.
Reported-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
A check that rejects a CDB with FUA bit set if no write cache is
emulated was added by the following commit:
fde9f50 target: Add sanity checks for DPO/FUA bit usage
The condition is as follows:
if (!dev->dev_attrib.emulate_fua_write ||
!dev->dev_attrib.emulate_write_cache)
However, this check is wrong if the backend device supports WCE but
"emulate_write_cache" is disabled.
This patch uses se_dev_check_wce() (previously named
spc_check_dev_wce) to invoke transport->get_write_cache() if the
device has a write cache or check the "emulate_write_cache" attribute
otherwise.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christophe Vu-Brugier <cvubrugier@fastmail.fm>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a NULL pointer dereference triggered by a late
target_configure_device() -> alloc_workqueue() failure that results
in target_free_device() being called with DF_CONFIGURED already set,
which subsequently OOPses in destroy_workqueue() code.
Currently this only happens at modprobe target_core_mod time when
core_dev_setup_virtual_lun0() -> target_configure_device() fails,
and the explicit target_free_device() gets called.
To address this bug originally introduced by commit 0fd97ccf45, go
ahead and move DF_CONFIGURED to end of target_configure_device()
code to handle this special failure case.
Reported-by: Claudio Fleiner <cmf@daterainc.com>
Cc: Claudio Fleiner <cmf@daterainc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org> # v3.7+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a NULL pointer dereference OOPs with pSCSI backends
within target_core_stat.c code. The bug is caused by a configfs attr
read if no pscsi_dev_virt->pdv_sd has been configured.
Reported-by: Olaf Hering <olaf@aepfle.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a missing set of conditional check braces in
ft_invl_hw_context() originally introduced by commit dcd998ccd
when handling DDP failures in ft_recv_write_data() code.
commit dcd998ccdb
Author: Kiran Patil <kiran.patil@intel.com>
Date: Wed Aug 3 09:20:01 2011 +0000
tcm_fc: Handle DDP/SW fc_frame_payload_get failures in ft_recv_write_data
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Kiran Patil <kiran.patil@intel.com>
Cc: <stable@vger.kernel.org> # 3.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a se_cmd->cmd_kref leak buf when se_sess->sess_tearing_down
is true within target_get_sess_cmd() submission path code.
This se_cmd reference leak can occur during active session shutdown when
ack_kref=1 is passed by target_submit_cmd_[map_sgls,tmr]() callers.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: <stable@vger.kernel.org> # 3.6+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes loopback, usb-gadget, vhost-scsi and xen-scsiback
fabric code to invoke transport_register_session() instead of the
unprotected flavour, to ensure se_tpg->session_lock is taken when
adding new session list nodes to se_tpg->tpg_sess_list.
Note that since these four fabric drivers already hold their own
internal TPG mutexes when accessing se_tpg->tpg_sess_list, and
consist of a single se_session created through configfs attribute
access, no list corruption can currently occur.
So for correctness sake, go ahead and use the se_tpg->session_lock
protected version for these four fabric drivers.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a iser specific logout bug where early complete()
of conn->conn_logout_comp in iscsit_close_connection() was causing
isert_wait4logout() to complete too soon, triggering a use after
free NULL pointer dereference of iscsi_conn memory.
The complete() was originally added for traditional iscsi-target
when a ISCSI_LOGOUT_OP failed in iscsi_target_rx_opcode(), but given
iser-target does not wait in logout failure, this special case needs
to be avoided.
Reported-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Slava Shwartsman <valyushash@gmail.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This reverts commit 72859d91d9.
The original patch was wrong, iscsit_close_connection() still needs
to release iscsi_conn during both normal + exception IN_LOGOUT status
with ib_isert enabled.
The original OOPs is due to completing conn_logout_comp early within
iscsit_close_connection(), causing isert_wait4logout() to complete
instead of waiting for iscsit_logout_post_handler_*() to be called.
Reported-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Slava Shwartsman <valyushash@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that incoming FUA=1 bit check is enforced for backends with FUA or
WCE disabled, go ahead and disallow the changing of related backend
attributes when active fabric exports exist.
This is required to avoid potential failures with existing initiator
LUN registrations that have been previously created with FUA=1.
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch exposes a new ../iscsi/$IQN/$TPGT/dynamic_sessions attribute
to dump the currently active sessions by iSCSI InitiatorName that have
been created with dynamically generated se_node_acls.
This information is useful so that user-space can optionally perform
dynamic -> explicit NodeACL conversion based on $INITIATOR_WWPN.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a new helper function that can be used by fabric driver
TPG attributes for dumping the list of active sessions with a dynamically
generated se_node_acl. (generate_node_acl=1).
It prints one se_node_acl->initiatorname per line, up to PAGE_SIZE which
is due to the current limitiation of single page attribute output within
sysfs and configfs code.
Note that if a session is referencing a explicit NodeACL, the InitiatorName
will not appear within dynamic_sessions output.
Reported-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
With the new bio_vec backed iov_iter helpers we can simply set up
on bio_vec per LBA, all pointing to the same initiator-supplied
buffer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- Update vhost-scsi to support F_ANY_LAYOUT using mm/iov_iter.c
logic, and signal VERSION_1 support (MST + Viro + nab)
- Fix iscsi/iser-target to remove problematic active_ts_set usage
(Gavin Guo)
- Update iscsi/iser-target to support multi-sequence sendtargets
(Sagi)
- Fix original PR_APTPL_BUF_LEN 8k size limitation (Martin Svec)
- Add missing WRITE_SAME end-of-device sanity check (Bart)
- Check for LBA + sectors wrap-around in sbc_parse_cdb() (nab)
- Other various minor SPC/SBC compliance fixes based upon Ronnie
Sahlberg test suite (nab)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (32 commits)
target: Set LBPWS10 bit in Logical Block Provisioning EVPD
target: Fail UNMAP when emulate_tpu=0
target: Fail WRITE_SAME w/ UNMAP=1 when emulate_tpws=0
target: Add sanity checks for DPO/FUA bit usage
target: Perform PROTECT sanity checks for WRITE_SAME
target: Fail I/O with PROTECT bit when protection is unsupported
target: Check for LBA + sectors wrap-around in sbc_parse_cdb
target: Add missing WRITE_SAME end-of-device sanity check
iscsi-target: Avoid IN_LOGOUT failure case for iser-target
target: Fix PR_APTPL_BUF_LEN buffer size limitation
iscsi-target: Drop problematic active_ts_list usage
iscsi/iser-target: Support multi-sequence sendtargets text response
iser-target: Remove duplicate function names
vhost/scsi: potential memory corruption
vhost/scsi: Global tcm_vhost -> vhost_scsi rename
vhost/scsi: Drop left-over scsi_tcq.h include
vhost/scsi: Set VIRTIO_F_ANY_LAYOUT + VIRTIO_F_VERSION_1 feature bits
vhost/scsi: Add ANY_LAYOUT support in vhost_scsi_handle_vq
vhost/scsi: Add ANY_LAYOUT iov -> sgl mapping prerequisites
vhost/scsi: Change vhost_scsi_map_to_sgl to accept iov ptr + len
...
This patch sets the missing LBPWS10 bit within spc_emulate_evpd_b2()
in order to signal WRITE_SAME (10) w/ UNMAP support, following the
existing LBPWS bit to signal WRITE_SAME (16) w/ UNMAP support.
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a check within sbc_parse_cdb() to fail a UNMAP op,
if the backend device has emulate_tpu disabled.
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a check within sbc_setup_write_same() to fail a
WRITE_SAME w/ UNMAP=1 op, if the backend device has emulate_tpws
disabled.
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a sbc_check_dpofua() function that performs sanity
checks for DPO/FUA command bits.
It introduces checks to fail when either bit is set, but the backend
device is not advertising support for them.
It also moves the existing cmd->se_cmd_flags |= SCF_FUA assignement
into the new helper function.
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a call to sbc_check_prot() within sbc_setup_write_same()
code to perform the various protection releated sanity checks, including
failing if WRPROTECT or RDPROTECT is set for a backend device that has
not advertised support for T10-PI.
Also, since WRITE_SAME + T10-PI is currently not supported by IBLOCK +
FILEIO backends, go ahead and fail if ->execute_write_same() is invoked
with a non zero cmd->prot_op.
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds an explicit check for WRPROTECT + RDPROTECT bit usage
within sbc_check_prot(), and fails with TCM_INVALID_CDB_FIELD if the
backend device does not have protection enabled.
Also, update sbc_check_prot() to return sense_reason_t in order to
propigate up the correct sense ASQ.
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a check to sbc_parse_cdb() in order to detect when
an LBA + sector vs. end-of-device calculation wraps when the LBA is
sufficently large enough (eg: 0xFFFFFFFFFFFFFFFF).
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a check to sbc_setup_write_same() to verify
the incoming WRITE_SAME LBA + number of blocks does not exceed
past the end-of-device.
Also check for potential LBA wrap-around as well.
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Martin Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org # 3.8+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses the original PR_APTPL_BUF_LEN = 8k limitiation
for write-out of PR APTPL metadata that Martin has recently been
running into.
It changes core_scsi3_update_and_write_aptpl() to use vzalloc'ed
memory instead of kzalloc, and increases the default hardcoded
length to 256k.
It also adds logic in core_scsi3_update_and_write_aptpl() to double
the original length upon core_scsi3_update_aptpl_buf() failure, and
retries until the vzalloc'ed buffer is large enough to accommodate
the outgoing APTPL metadata.
Reported-by: Martin Svec <martin.svec@zoner.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In case sendtargets response is larger than initiator MRDSL, we
send a partial sendtargets response (setting F=0, C=1, TTT!=0xffffffff),
accept a consecutive empty text message and send the rest of the payload.
In case we are done, we set F=1, C=0, TTT=0xffffffff.
We do that by storing the sendtargets response bytes done under
the session.
This patch also makes iscsit_find_cmd_from_itt public for isert.
(Re-add cmd->maxcmdsn_inc and clear in iscsit_build_text_rsp - nab)
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
No reason to allocate a buffer of size bigger than initiator
MaxRecvDataSegmentLength. Moreover, we need to respect initiator
MRDSL and not send a larger payload.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Seems strange to see in include/target/iscsi/iscsi_transport.h:
include "../../../drivers/target/iscsi/iscsi_target_core.h"
Move it to it's natural location.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Contrary to common expectations for an "int" return, these functions
return only a positive value -- if used correctly they cannot even
return 0 because the message header will necessarily be in the skb.
This makes the very common pattern of
if (genlmsg_end(...) < 0) { ... }
be a whole bunch of dead code. Many places also simply do
return nlmsg_end(...);
and the caller is expected to deal with it.
This also commonly (at least for me) causes errors, because it is very
common to write
if (my_function(...))
/* error condition */
and if my_function() does "return nlmsg_end()" this is of course wrong.
Additionally, there's not a single place in the kernel that actually
needs the message length returned, and if anyone needs it later then
it'll be very easy to just use skb->len there.
Remove this, and make the functions void. This removes a bunch of dead
code as described above. The patch adds lines because I did
- return nlmsg_end(...);
+ nlmsg_end(...);
+ return 0;
I could have preserved all the function's return values by returning
skb->len, but instead I've audited all the places calling the affected
functions and found that none cared. A few places actually compared
the return value with <= 0 in dump functionality, but that could just
be changed to < 0 with no change in behaviour, so I opted for the more
efficient version.
One instance of the error I've made numerous times now is also present
in net/phonet/pn_netlink.c in the route_dumpit() function - it didn't
check for <0 or <=0 and thus broke out of the loop every single time.
I've preserved this since it will (I think) have caused the messages to
userspace to be formatted differently with just a single message for
every SKB returned to userspace. It's possible that this isn't needed
for the tools that actually use this, but I don't even know what they
are so couldn't test that changing this behaviour would be acceptable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of pushing each byte via stack the %*ph specifier allows to supply just
a pointer and length of the buffer. The patch converts code to use the
specifier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Everything else starts with ICF so the last two should as well.
Fix places they are used to match.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
For PGR reservation of type Write Exclusive Access, allow all non
reservation holding I_T nexuses with active registrations to READ
from the device.
This addresses a bug where active registrations that attempted
to READ would result in an reservation conflict.
Signed-off-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that fabric_max_sectors is no longer used to enforce the maximum
I/O size, go ahead and drop it's left-over usage in target-core and
associated backend drivers.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch drops the arbitrary maximum I/O size limit in sbc_parse_cdb(),
which currently for fabric_max_sectors is hardcoded to 8192 (4 MB for 512
byte sector devices), and for hw_max_sectors is a backend driver dependent
value.
This limit is problematic because Linux initiators have only recently
started to honor block limits MAXIMUM TRANSFER LENGTH, and other non-Linux
based initiators (eg: MSFT Fibre Channel) can also generate I/Os larger
than 4 MB in size.
Currently when this happens, the following message will appear on the
target resulting in I/Os being returned with non recoverable status:
SCSI OP 28h with too big sectors 16384 exceeds fabric_max_sectors: 8192
Instead, drop both [fabric,hw]_max_sector checks in sbc_parse_cdb(),
and convert the existing hw_max_sectors into a purely informational
attribute used to represent the granuality that backend driver and/or
subsystem code is splitting I/Os upon.
Also, update FILEIO with an explicit FD_MAX_BYTES check in fd_execute_rw()
to deal with the one special iovec limitiation case.
v2 changes:
- Drop hw_max_sectors check in sbc_parse_cdb()
Reported-by: Lance Gropper <lance.gropper@qosserver.com>
Reported-by: Stefan Priebe <s.priebe@profihost.ag>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: stable@vger.kernel.org # 3.4
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This is a much shorter set of patches that were on the go but didn't make it
in to the early pull request for the merge window. It's really a set of bug
fixes plus some final cleanup work on the new tag queue API.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJUlaYEAAoJEDeqqVYsXL0MmXAH/2UUcE11p0KBHMR4cAn76xrG
9093ZT9VZ4LH/Z7PbgwIWC4YHDqVpwA1+Trj1mh8PxiZz2SopWe27O2lQMRS5VUc
MN28kbmK3L0jQj+OUez10Da6k0hU/KL8TlWT765MxFDKCaAuPZ4u541tyZEIGmLL
olOQrn/fSlu+18QqqZ+D2rMaK7kGH6ZgbOadnRfYGkLjU4YeAMEC9L7UgnDxHiaN
gZozoARkGeAnDJERVETRTtAiOXGRH8sGCpue0yYlhZXpAQ9cFUkS/hMqDWnaVC2S
0x0w34RvbxSqO0gPT0K5XLoMiFyg04vnZ2xBVFBsANQTSEjQJO8USNAa4r74hf8=
=D3eN
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI update from James Bottomley:
"This is a much shorter set of patches that were on the go but didn't
make it in to the early pull request for the merge window. It's
really a set of bug fixes plus some final cleanup work on the new tag
queue API"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
storvsc: ring buffer failures may result in I/O freeze
ipr: set scsi_level correctly for disk arrays
ipr: add support for async scanning to speed up boot
scsi_debug: fix missing "break;" in SDEBUG_UA_CAPACITY_CHANGED case
scsi_debug: take sdebug_host_list_lock when changing capacity
scsi_debug: improve driver description in Kconfig
scsi_debug: fix compare and write errors
qla2xxx: fix race in handling rport deletion during recovery causes panic
scsi: blacklist RSOC for Microsoft iSCSI target devices
scsi: fix random memory corruption with scsi-mq + T10 PI
Revert "[SCSI] mpt3sas: Remove phys on topology change"
Revert "[SCSI] mpt2sas: Remove phys on topology change."
esas2r: Correct typos of "validate" in a comment
fc: FCP_PTA_SIMPLE is 0
ibmvfc: remove unused tag variable
scsi: remove MSG_*_TAG defines
scsi: remove scsi_set_tag_type
scsi: remove scsi_get_tag_type
scsi: never drop to untagged mode during queue ramp down
scsi: remove ->change_queue_type method
Pull SCSI target fixes from Nicholas Bellinger:
"The highlights this merge window include:
- Allow target fabric drivers to function as built-in. (Roland)
- Fix tcm_loop multi-TPG endpoint nexus bug. (Hannes)
- Move per device config_item_type into se_subsystem_api, allowing
configfs attributes to be defined at module_init time. (Jerome +
nab)
- Convert existing IBLOCK/FILEIO/RAMDISK/PSCSI/TCMU drivers to use
external configfs attributes. (nab)
- A number of iser-target fixes related to active session + network
portal shutdown stability during extended stress testing. (Sagi +
Slava)
- Dynamic allocation of T10-PI contexts for iser-target, fixing a
potentially bogus iscsi_np->tpg_np pointer reference in >= v3.14
code. (Sagi)
- iser-target performance + scalability improvements. (Sagi)
- Fixes for SPC-4 Persistent Reservation AllRegistrants spec
compliance. (Ilias + James + nab)
- Avoid potential short kern_sendmsg() in iscsi-target for now until
Al's conversion to use msghdr iteration is merged post -rc1.
(Viro)
Also, Sagi has requested a number of iser-target patches (9) that
address stability issues he's encountered during extended stress
testing be considered for v3.10.y + v3.14.y code. Given the amount of
LOC involved, it will certainly require extra backporting effort.
Apologies in advance to Greg-KH & Co on this. Sagi and I will be
working post-merge to ensure they each get applied correctly"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (53 commits)
target: Allow AllRegistrants to re-RESERVE existing reservation
uapi/linux/target_core_user.h: fix headers_install.sh badness
iscsi-target: Fail connection on short sendmsg writes
iscsi-target: nullify session in failed login sequence
target: Avoid dropping AllRegistrants reservation during unregister
target: Fix R_HOLDER bit usage for AllRegistrants
iscsi-target: Drop left-over bogus iscsi_np->tpg_np
iser-target: Fix wc->wr_id cast warning
iser-target: Remove code duplication
iser-target: Adjust log levels and prettify some prints
iser-target: Use debug_level parameter to control logging level
iser-target: Fix logout sequence
iser-target: Don't wait for session commands from completion context
iser-target: Reduce CQ lock contention by batch polling
iser-target: Introduce isert_poll_budget
iser-target: Remove an atomic operation from the IO path
iser-target: Remove redundant call to isert_conn_terminate
iser-target: Use single CQ for TX and RX
iser-target: Centralize completion elements to a context
iser-target: Cast wr_id with uintptr_t instead of unsinged long
...
This patch changes core_scsi3_pro_release() logic to allow an
existing AllRegistrants type reservation to be re-reserved by
any registered I_T nexus.
This addresses a issue where AllRegistrants type RESERVE was
receiving RESERVATION_CONFLICT status if dev_pr_res_holder did
not match the same I_T nexus, instead of just returning GOOD
status following spc4r34 Section 5.9.9:
"If the device server receives a PERSISTENT RESERVE OUT command
with RESERVE service action where the TYPE field and the SCOPE
field contain the same values as the existing type and scope
from a persistent reservation holder, it shall not make any
change to the existing persistent reservation and shall complete
the command with GOOD status."
Reported-by: Ilias Tsitsimpis <i.tsitsimpis@gmail.com>
Cc: Ilias Tsitsimpis <i.tsitsimpis@gmail.com>
Cc: Lee Duncan <lduncan@suse.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes iscsit_do_tx_data() to fail on short writes
when kernel_sendmsg() returns a value different than requested
transfer length, returning -EPIPE and thus causing a connection
reset to occur.
This avoids a potential bug in the original code where a short
write would result in kernel_sendmsg() being called again with
the original iovec base + length.
In practice this has not been an issue because iscsit_do_tx_data()
is only used for transferring 48 byte headers + 4 byte digests,
along with seldom used control payloads from NOPIN + TEXT_RSP +
REJECT with less than 32k of data.
So following Al's audit of iovec consumers, go ahead and fail
the connection on short writes for now, and remove the bogus
logic ahead of his proper upstream fix.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: David S. Miller <davem@davemloft.net>
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In case login sequence failed, make sure conn->sess is
NULL before calling wait_conn as some transports (iser)
may rely on that (waiting for session commands).
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes an issue with AllRegistrants reservations where
an unregister operation by the I_T nexus reservation holder would
incorrectly drop the reservation, instead of waiting until the
last active I_T nexus is unregistered as per SPC-4.
This includes updating __core_scsi3_complete_pro_release() to reset
dev->dev_pr_res_holder with another pr_reg for this special case,
as well as a new 'unreg' parameter to determine when the release
is occuring from an implicit unregister, vs. explicit RELEASE.
It also adds special handling in core_scsi3_free_pr_reg_from_nacl()
to release the left-over pr_res_holder, now that pr_reg is deleted
from pr_reg_list within __core_scsi3_complete_pro_release().
Reported-by: Ilias Tsitsimpis <i.tsitsimpis@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes the usage of R_HOLDER bit for an All Registrants
reservation in READ_FULL_STATUS, where only the registration who
issued RESERVE was being reported as having an active reservation.
It changes core_scsi3_pri_read_full_status() to check ahead of the
list walk of active registrations to see if All Registrants is active,
and if so set R_HOLDER bit and scope/type fields for all active
registrations.
Reported-by: Ilias Tsitsimpis <i.tsitsimpis@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch drops the left-over iscsi_np->tpg_np pointer, now
that iser-target PI is able to dynamically allocate PI contexts
per I/O, instead of needing to determine support using a TPG
attribute with this bogus reference.
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
iSER will report supported protection operations based on
the tpg attribute t10_pi settings and HCA PI offload capabilities.
If the HCA does not support PI offload or tpg attribute t10_pi is
not set, we fall to SW PI mode.
In order to do that, we move iscsit_get_sup_prot_ops after connection
tpg assignment.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Since commit 0fc4ea701f ("Target/iser: Don't put isert_conn inside
disconnected handler") we put the conn kref in isert_wait_conn, so we
need .wait_conn to be invoked also in the error path.
Introduce call to isert_conn_terminate (called under lock)
which transitions the connection state to TERMINATING and calls
rdma_disconnect. If the state is already teminating, just bail
out back (temination started).
Also, make sure to destroy the connection when getting a connect
error event if didn't get to connected (state UP). Same for the
handling of REJECTED and UNREACHABLE cma events.
Squashed:
iscsi-target: Add call to wait_conn in establishment error flow
Reported-by: Slava Shwartsman <valyushash@gmail.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull networking updates from David Miller:
1) New offloading infrastructure and example 'rocker' driver for
offloading of switching and routing to hardware.
This work was done by a large group of dedicated individuals, not
limited to: Scott Feldman, Jiri Pirko, Thomas Graf, John Fastabend,
Jamal Hadi Salim, Andy Gospodarek, Florian Fainelli, Roopa Prabhu
2) Start making the networking operate on IOV iterators instead of
modifying iov objects in-situ during transfers. Thanks to Al Viro
and Herbert Xu.
3) A set of new netlink interfaces for the TIPC stack, from Richard
Alpe.
4) Remove unnecessary looping during ipv6 routing lookups, from Martin
KaFai Lau.
5) Add PAUSE frame generation support to gianfar driver, from Matei
Pavaluca.
6) Allow for larger reordering levels in TCP, which are easily
achievable in the real world right now, from Eric Dumazet.
7) Add a variable of napi_schedule that doesn't need to disable cpu
interrupts, from Eric Dumazet.
8) Use a doubly linked list to optimize neigh_parms_release(), from
Nicolas Dichtel.
9) Various enhancements to the kernel BPF verifier, and allow eBPF
programs to actually be attached to sockets. From Alexei
Starovoitov.
10) Support TSO/LSO in sunvnet driver, from David L Stevens.
11) Allow controlling ECN usage via routing metrics, from Florian
Westphal.
12) Remote checksum offload, from Tom Herbert.
13) Add split-header receive, BQL, and xmit_more support to amd-xgbe
driver, from Thomas Lendacky.
14) Add MPLS support to openvswitch, from Simon Horman.
15) Support wildcard tunnel endpoints in ipv6 tunnels, from Steffen
Klassert.
16) Do gro flushes on a per-device basis using a timer, from Eric
Dumazet. This tries to resolve the conflicting goals between the
desired handling of bulk vs. RPC-like traffic.
17) Allow userspace to ask for the CPU upon what a packet was
received/steered, via SO_INCOMING_CPU. From Eric Dumazet.
18) Limit GSO packets to half the current congestion window, from Eric
Dumazet.
19) Add a generic helper so that all drivers set their RSS keys in a
consistent way, from Eric Dumazet.
20) Add xmit_more support to enic driver, from Govindarajulu
Varadarajan.
21) Add VLAN packet scheduler action, from Jiri Pirko.
22) Support configurable RSS hash functions via ethtool, from Eyal
Perry.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1820 commits)
Fix race condition between vxlan_sock_add and vxlan_sock_release
net/macb: fix compilation warning for print_hex_dump() called with skb->mac_header
net/mlx4: Add support for A0 steering
net/mlx4: Refactor QUERY_PORT
net/mlx4_core: Add explicit error message when rule doesn't meet configuration
net/mlx4: Add A0 hybrid steering
net/mlx4: Add mlx4_bitmap zone allocator
net/mlx4: Add a check if there are too many reserved QPs
net/mlx4: Change QP allocation scheme
net/mlx4_core: Use tasklet for user-space CQ completion events
net/mlx4_core: Mask out host side virtualization features for guests
net/mlx4_en: Set csum level for encapsulated packets
be2net: Export tunnel offloads only when a VxLAN tunnel is created
gianfar: Fix dma check map error when DMA_API_DEBUG is enabled
cxgb4/csiostor: Don't use MASTER_MUST for fw_hello call
net: fec: only enable mdio interrupt before phy device link up
net: fec: clear all interrupt events to support i.MX6SX
net: fec: reset fep link status in suspend function
net: sock: fix access via invalid file descriptor
net: introduce helper macro for_each_cmsghdr
...
... making both non-draining. That means that tcp_recvmsg() becomes
non-draining. And _that_ would break iscsit_do_rx_data() unless we
a) make sure tcp_recvmsg() is uniformly non-draining (it is)
b) make sure it copes with arbitrary (including shifted)
iov_iter (it does, all it uses is iov_iter primitives)
c) make iscsit_do_rx_data() initialize ->msg_iter only once.
Fortunately, (c) is doable with minimal work and we are rid of one
the two places where kernel send/recvmsg users would be unhappy with
non-draining behaviour.
Actually, that makes all but one of ->recvmsg() instances iov_iter-clean.
The exception is skcipher_recvmsg() and it also isn't hard to convert
to primitives (iov_iter_get_pages() is needed there). That'll wait
a bit - there's some interplay with ->sendmsg() path for that one.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Conflicts:
drivers/scsi/scsi_debug.c
Agreed and tested resolution to a merge problem between a fix in scsi_debug
and a driver update
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For SPI drivers use the message definitions from scsi.h, and for target
drivers introduce a new TCM_*_TAG namespace.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com
Since we got rid of ordered tag support in 2010 the prime use case of
switching on and off ordered tags has been obsolete. The other function
of enabling/disabling tagging entirely has only been correctly implemented
by the 53c700 driver and isn't generally useful.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Delete a local array that is only used to be initialized by memset.
A semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier x;
type T;
@@
{
... when any
-T x[...];
<+... when != x
- memset(x,...);
...+>
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In iscsi_target_init_module() unwind transport protocol registration in case
that iscsit_load_discovery_tpg() failed.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
tcm_loop has the I_T nexus associated with the HBA. This causes
commands to become misdirected if the HBA has more than one
target portal group; any command is then being sent to the
first target portal group instead of the correct one.
The nexus needs to be associated with the target portal group
instead.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: <stable@vger.kernel.org> # 3.0+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that PSCSI is only exposing four hw_* read-only device attributes,
go ahead and drop the left-over -> legacy PHBA_PDEV checks in various
se_dev_set_* code, since it's now only used by virtual devices.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that backend drivers are populating their own device attributes,
go ahead and remove left-over definitions + internal attribute list
of device attributes from target_core_configfs.c code
Also update TB_CIT_SETUP(dev_attrib,...) to signal ct_attr = NULL.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts PSCSI to use an external set of device attributes,
and utilizes target_core_backend_configfs.h macros to generate a default
set of configfs extended-attr handlers.
It calls target_core_setup_sub_cits() to setup the initial config_item_type
based on existing target_core_configfs.c defaults, and using configfs_attribute
for hw_pi_prot_type, hw_block_size, hw_max_sectors, hw_queue_depth populates
pscsi_backend_dev_attrs[]
Only these four hw_* read-only device attributes are exports for PSCSI.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts TCM-USER to use an external set of device attributes,
and utilizes target_core_backend_configfs.h macros to generate a default
set of configfs extended-attr handlers.
It calls target_core_setup_sub_cits() to setup the initial config_item_type
based on existing target_core_configfs.c defaults, and using configfs_attribute
generated by DEF_TB_DEFAULT_ATTRIBS(tcmu) populates tcmu_backend_dev_attrs[]
It introduces no function change for existing TCMU device attributes.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts RAMDISK to use an external set of device attributes,
and utilizes target_core_backend_configfs.h macros to generate a default
set of configfs extended-attr handlers.
It calls target_core_setup_sub_cits() to setup the initial config_item_type
based on existing target_core_configfs.c defaults, and using configfs_attribute
generated by DEF_TB_DEFAULT_ATTRIBS(rc_mcp) populates rd_mcp_backend_dev_attrs[]
It introduces no functional change for existing RD_MCP device attributes.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts FILEIO to use an external set of device attributes,
and utilizes target_core_backend_configfs.h macros to generate a default
set of configfs extended-attr handlers.
It calls target_core_setup_sub_cits() to setup the initial config_item_type
based on existing target_core_configfs.c defaults, and using configfs_attribute
generated by DEF_TB_DEFAULT_ATTRIBS(fileio) populates fileio_backend_dev_attrs[]
It introduces no functional change for existing FILEIO device attributes.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts IBLOCK to use an external set of device attributes,
and utilizes target_core_backend_configfs.h macros to generate a default
set of configfs extended-attr handlers.
It calls target_core_setup_sub_cits() to setup the initial config_item_type
based on existing target_core_configfs.c defaults, and using configfs_attribute
generated by DEF_TB_DEFAULT_ATTRIBS(iblock) populates iblock_backend_dev_attrs[]
It introduces no functional change for existing IBLOCK device attributes.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that target_core_backend_configfs.h macros will be using these
se_dev_set attribute functions externally to allow backend drivers
to populate different attributes, go ahead and add EXPORT_SYMBOL()
for the existing default set of 30 device attributes.
Also update target_core_backend.h with proper function prototypes.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds support for dev_stat_cit as an external config_item_type
using TB_CIT_SETUP() helper macro, and sets only ct_group_ops following
existing code.
It updates target_core_make_subdev() + target_core_setup_dev_attrib_cit() +
struct target_backend_cits, and drops left-over target_core_dev_stat_cit
from target_core_configfs.c code and update comments.
This patch introduces no functional change from existing code.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds support for dev_alua_tg_pt_gps_cit as an external config_item_type
using TB_CIT_SETUP() helper macro, and sets only ct_group_ops following
existing code.
It updates target_core_make_subdev() + target_core_setup_dev_attrib_cit() +
struct target_backend_cits, and drops left-over target_core_dev_alua_tg_pt_gps_cit
from target_core_configfs.c code and update comments.
This patch introduces no functional change from existing code.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds support for dev_wwn_cit as an external config_item_type
using TB_CIT_SETUP() helper macro, and sets both ct_item_ops + ct_attr
following existing code.
It updates target_core_make_subdev() + target_core_setup_dev_attrib_cit() +
struct target_backend_cits, and drops left-over target_core_dev_wwn_cit
from target_core_configfs.c code and update comments.
This patch introduces no functional change from existing code.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds support for dev_pr_cit as an external config_item_type
using TB_CIT_SETUP() helper macro, and sets both ct_item_ops + ct_attr
following existing code.
It updates target_core_make_subdev() + target_core_setup_dev_attrib_cit() +
struct target_backend_cits, and drops left-over target_core_dev_pr_cit
from target_core_configfs.c code and update comments.
This patch introduces no functional change from existing code.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds support for dev_attrib_cit as an external config_item_type
using TB_CIT_SETUP() helper macro, and sets both ct_item_ops + ct_attr
following existing code.
It updates target_core_make_subdev() + target_core_setup_dev_attrib_cit() +
struct target_backend_cits, and drops left-over target_core_dev_attrib_cit
from target_core_configfs.c code and update comments.
This patch introduces no functional change from existing code.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds initial support for dev_cit as external config_item_type.
This includes a new struct target_backend_cits to hold the external CITs
within struct se_subsystem_api, and target_core_setup_sub_cits() to be
used by backend drivers ahead of transport_subsystem_register().
It adds a TB_CIT_SETUP() helper following target_core_fabric_configfs.c
to perform the config_item_type assignments.
Also, drop left-over target_core_dev_cit from target_core_configfs.c code
and update comments.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The module_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If we try to create a fabric directory in configfs for one of the
default hard-coded fabric modules (iscsi and loopback), and that
fabric is actually built into the kernel, then the operation will
spuriously fail because request_module() (for the code that's already
linked into the kernel) fails.
Fix this by running the autoprobing code only if an initial
target_core_get_fabric() fails.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
SPC-3 defines SERVICE ACTION IN(12), SERVICE_ACTION OUT(12),
SERVICE ACTION OUT(16), and SERVICE ACTION BIDIRECTIONAL.
And READ MEDIA SERIAL NUMBER has long since been deprecated.
So update callers to refer to the new cdb name.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Tested-by: Robert Elliott <elliott@hp.com>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
SPC-3 defines SERVICE ACTION IN(12) and SERVICE ACTION IN(16).
So rename SERVICE_ACTION_IN to SERVICE_ACTION_IN_16 to be
consistent with SPC and to allow for better distinction.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Tested-by: Robert Elliott <elliott@hp.com>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Drop the now unused reason argument from the ->change_queue_depth method.
Also add a return value to scsi_adjust_queue_depth, and rename it to
scsi_change_queue_depth now that it can be used as the default
->change_queue_depth implementation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
All drivers use the implementation for ramping the queue up and down, so
instead of overloading the change_queue_depth method call the
implementation diretly if the driver opts into it by setting the
track_queue_depth flag in the host template.
Note that a few drivers validated the new queue depth in their
change_queue_depth method, but as we never go over the queue depth
set during slave_configure or the sysfs file this isn't nessecary
and can safely be removed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Venkatesh Srinivas <venkateshs@google.com>
This patch fix spelling typo in printk and Kconfig within
various part of kernel sources.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove the tagged argument from scsi_adjust_queue_depth, and just let it
handle the queue depth. For most drivers those two are fairly separate,
given that most modern drivers don't care about the SCSI "tagged" status
of a command at all, and many old drivers allow queuing of multiple
untagged commands in the driver.
Instead we start out with the ->simple_tags flag set before calling
->slave_configure, which is how all drivers actually looking at
->simple_tags except for one worke anyway. The one other case looks
broken, but I've kept the behavior as-is for now.
Except for that we only change ->simple_tags from the ->change_queue_type,
and when rejecting a tag message in a single driver, so keeping this
churn out of scsi_adjust_queue_depth is a clear win.
Now that the usage of scsi_adjust_queue_depth is more obvious we can
also remove all the trivial instances in ->slave_alloc or ->slave_configure
that just set it to the cmd_per_lun default.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Allow a driver to ask for block layer tags by setting .use_blk_tags in the
host template, in which case it will always see a valid value in
request->tag, similar to the behavior when using blk-mq. This means even
SCSI "untagged" commands will now have a tag, which is especially useful
when using a host-wide tag map.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Remove the ordered_tags field, we haven't been issuing ordered tags based
on it since the big barrier rework in 2010.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Most drivers use exactly the same implementation, so provide it as a
library function.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
PREEMPT (and PREEMPT AND ABORT) should return CONFLICT iff a specified
SERVICE ACTION RESERVATION KEY is specified and matches no existing
persistent reservation.
Without this patch, a PREEMPT will return CONFLICT if either all
reservations are held by the initiator (self preemption) or there is
nothing to preempt. According to the spec, both of these cases should
succeed.
Signed-off-by: Steven Allen <steven.allen@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The fact that a target is published on the any address has no bearing on
which port(s) it is published. SendTargets should always send the
portal's port, not the port used for discovery.
Signed-off-by: Steven Allen <steven.allen@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If an initiator sends a zero-length command (e.g. TEST UNIT READY) but
sets the transfer direction in the transport layer to indicate a
data-out phase, we still shouldn't try to transfer data. At best it's
a NOP, and depending on the transport, we might crash on an
uninitialized sg list.
Reported-by: Craig Watson <craig.watson@vanguard-rugged.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: <stable@vger.kernel.org> # 3.1
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"Here are the target updates for v3.18-rc2 code. These where
originally destined for -rc1, but due to the combination of travel
last week for KVM Forum and my mistake of taking the three week merge
window literally, the pull request slipped.. Apologies for that.
Things where reasonably quiet this round. The highlights include:
- New userspace backend driver (target_core_user.ko) by Shaohua Li
and Andy Grover
- A number of cleanups in target, iscsi-taret and qla_target code
from Joern Engel
- Fix an OOPs related to queue full handling with CHECK_CONDITION
status from Quinn Tran
- Fix to disable TX completion interrupt coalescing in iser-target,
that was causing problems on some hardware
- Fix for PR APTPL metadata handling with demo-mode ACLs
I'm most excited about the new backend driver that uses UIO + shared
memory ring to dispatch I/O and control commands into user-space.
This was probably the most requested feature by users over the last
couple of years, and opens up a new area of development + porting of
existing user-space storage applications to LIO. Thanks to Shaohua +
Andy for making this happen.
Also another honorable mention, a new Xen PV SCSI driver was merged
via the xen/tip.git tree recently, which puts us now at 10 target
drivers in upstream! Thanks to David Vrabel + Juergen Gross for their
work to get this code merged"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (40 commits)
target/file: fix inclusive vfs_fsync_range() end
iser-target: Disable TX completion interrupt coalescing
target: Add force_pr_aptpl device attribute
target: Fix APTPL metadata handling for dynamic MappedLUNs
qla_target: don't delete changed nacls
target/user: Recalculate pad size inside is_ring_space_avail()
tcm_loop: Fixup tag handling
iser-target: Fix smatch warning
target/user: Fix up smatch warnings in tcmu_netlink_event
target: Add a user-passthrough backstore
target: Add documentation on the target userspace pass-through driver
uio: Export definition of struct uio_device
target: Remove unneeded check in sbc_parse_cdb
target: Fix queue full status NULL pointer for SCF_TRANSPORT_TASK_SENSE
qla_target: rearrange struct qla_tgt_prm
qla_target: improve qlt_unmap_sg()
qla_target: make some global functions static
qla_target: remove unused parameter
target: simplify core_tmr_abort_task
target: encapsulate smp_mb__after_atomic()
...
Pull core block layer changes from Jens Axboe:
"This is the core block IO pull request for 3.18. Apart from the new
and improved flush machinery for blk-mq, this is all mostly bug fixes
and cleanups.
- blk-mq timeout updates and fixes from Christoph.
- Removal of REQ_END, also from Christoph. We pass it through the
->queue_rq() hook for blk-mq instead, freeing up one of the request
bits. The space was overly tight on 32-bit, so Martin also killed
REQ_KERNEL since it's no longer used.
- blk integrity updates and fixes from Martin and Gu Zheng.
- Update to the flush machinery for blk-mq from Ming Lei. Now we
have a per hardware context flush request, which both cleans up the
code should scale better for flush intensive workloads on blk-mq.
- Improve the error printing, from Rob Elliott.
- Backing device improvements and cleanups from Tejun.
- Fixup of a misplaced rq_complete() tracepoint from Hannes.
- Make blk_get_request() return error pointers, fixing up issues
where we NULL deref when a device goes bad or missing. From Joe
Lawrence.
- Prep work for drastically reducing the memory consumption of dm
devices from Junichi Nomura. This allows creating clone bio sets
without preallocating a lot of memory.
- Fix a blk-mq hang on certain combinations of queue depths and
hardware queues from me.
- Limit memory consumption for blk-mq devices for crash dump
scenarios and drivers that use crazy high depths (certain SCSI
shared tag setups). We now just use a single queue and limited
depth for that"
* 'for-3.18/core' of git://git.kernel.dk/linux-block: (58 commits)
block: Remove REQ_KERNEL
blk-mq: allocate cpumask on the home node
bio-integrity: remove the needless fail handle of bip_slab creating
block: include func name in __get_request prints
block: make blk_update_request print prefix match ratelimited prefix
blk-merge: don't compute bi_phys_segments from bi_vcnt for cloned bio
block: fix alignment_offset math that assumes io_min is a power-of-2
blk-mq: Make bt_clear_tag() easier to read
blk-mq: fix potential hang if rolling wakeup depth is too high
block: add bioset_create_nobvec()
block: use bio_clone_fast() in blk_rq_prep_clone()
block: misplaced rq_complete tracepoint
sd: Honor block layer integrity handling flags
block: Replace strnicmp with strncasecmp
block: Add T10 Protection Information functions
block: Don't merge requests if integrity flags differ
block: Integrity checksum flag
block: Relocate bio integrity flags
block: Add a disk flag to block integrity profile
block: Add prefix to block integrity profile flags
...
Both of the file target's calls to vfs_fsync_range() got the end offset
off by one. The range is inclusive, not exclusive. It would sync a bit
more data than was required.
The sync path already tested the length of the range and fell back to
LLONG_MAX so I copied that pattern in the rw path.
This is untested. I found the errors by inspection while following other
code.
Signed-off-by: Zach Brown <zab@zabbo.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a force_pr_aptpl device attribute used to force SPC-3 PR
Activate Persistence across Target Power Loss (APTPL) operation. This
makes PR metadata write-out occur during state change regardless if new
PERSISTENT_RESERVE_OUT CDBs have their APTPL feature bit set.
This is useful during H/A failover in active/passive setups where all PR
state is being re-created on a different node, driven by configfs backend
device + export layout and pre-loaded $DEV/pr/res_aptpl_metadata.
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug in handling of SPC-3 PR Activate Persistence
across Target Power Loss (APTPL) logic where re-creation of state for
MappedLUNs from dynamically generated NodeACLs did not occur during
I_T Nexus establishment.
It adds the missing core_scsi3_check_aptpl_registration() call during
core_tpg_check_initiator_node_acl() -> core_tpg_add_node_to_devs() in
order to replay any pre-loaded APTPL metadata state associated with
the newly connected SCSI Initiator Port.
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If more than one thread is waiting for command ring space that includes
a PAD, then if the first one finishes (inserts a PAD and a CMD at the
start of the cmd ring) then the second one will incorrectly think it still
needs to insert a PAD (i.e. cmdr_space_needed is now wrong.) This will
lead to it asking for more space than it actually needs, and then inserting
a PAD somewhere else than at the end -- not what we want.
This patch moves the pad calculation inside is_ring_space_available() so
in the above scenario the second thread would then ask for space not
including a PAD. The patch also inserts a PAD op based upon an up-to-date
cmd_head, instead of the potentially stale value.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The SCSI command tag is set to the tag assigned from the block
layer, not the SCSI-II tag message. So we need to convert
it into the correct SCSI-II tag message based on the
device flags, not the tag value itself.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes up the following unused return smatch warnings:
drivers/target/target_core_user.c:778 tcmu_netlink_event warn: unused return: ret = nla_put_string()
drivers/target/target_core_user.c:780 tcmu_netlink_event warn: unused `return: ret = nla_put_u32()
(Fix up missing semicolon: grover)
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Add a LIO storage engine that presents commands to userspace for execution.
This would allow more complex backstores to be implemented out-of-kernel,
and also make experimentation a-la FUSE (but at the SCSI level -- "SUSE"?)
possible.
It uses a mmap()able UIO device per LUN to share a command ring and data
area. The commands are raw SCSI CDBs and iovs for in/out data. The command
ring is also reused for returning scsi command status and optional sense
data.
This implementation is based on Shaohua Li's earlier version but heavily
modified. Differences include:
* Shared memory allocated by kernel, not locked-down user pages
* Single ring for command request and response
* Offsets instead of embedded pointers
* Generic SCSI CDB passthrough instead of per-cmd specialization in ring
format.
* Uses UIO device instead of anon_file passed in mailbox.
* Optional in-kernel handling of some commands.
The main reason for these differences is to permit greater resiliency
if the user process dies or hangs.
Things not yet implemented (on purpose):
* Zero copy. The data area is flexible enough to allow page flipping or
backend-allocated pages to be used by fabrics, but it's not clear these
are performance wins. Can come later.
* Out-of-order command completion by userspace. Possible to add by just
allowing userspace to change cmd_id in rsp cmd entries, but currently
not supported.
* No locks between kernel cmd submission and completion routines. Sounds
like it's possible, but this can come later.
* Sparse allocation of mmaped area. Current code vmallocs the whole thing.
If the mapped area was larger and not fully mapped then the driver would
have more freedom to change cmd and data area sizes based on demand.
Current code open issues:
* The use of idrs may be overkill -- we maybe can replace them with a
simple counter to generate cmd_ids, and a hash table to get a cmd_id's
associated pointer.
* Use of a free-running counter for cmd ring instead of explicit modulo
math. This would require power-of-2 cmd ring size.
(Add kconfig depends NET - Randy)
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The check of SCF_SCSI_DATA_CDB seems to be a remnant from before hch's
refactoring of this function. There are no places where that flag is set
that cmd->execute_cmd isn't also set.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
During temporary resource starvation at lower transport layer, command
is placed on queue full retry path, which expose this problem. The TCM
queue full handling of SCF_TRANSPORT_TASK_SENSE currently sends the same
cmd twice to lower layer. The 1st time led to cmd normal free path.
The 2nd time cause Null pointer access.
This regression bug was originally introduced v3.1-rc code in the
following commit:
commit e057f53308
Author: Christoph Hellwig <hch@infradead.org>
Date: Mon Oct 17 13:56:41 2011 -0400
target: remove the transport_qf_callback se_cmd callback
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
list_for_each_entry_safe is necessary if list objects are deleted from
the list while traversing it. Not the case here, so we can use the base
list_for_each_entry variant.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The target code has a rather generous helping of smp_mb__after_atomic()
throughout the code base. Most atomic operations were followed by one
and none were preceded by smp_mb__before_atomic(), nor accompanied by a
comment explaining the need for a barrier.
Instead of trying to prove for every case whether or not it is needed,
this patch introduces atomic_inc_mb() and atomic_dec_mb(), which
explicitly include the memory barriers before and after the atomic
operation. For now they are defined in a target header, although they
could be of general use.
Most of the existing atomic/mb combinations were replaced by the new
helpers. In a few cases the atomic was sandwiched in
spin_lock/spin_unlock and I simply removed the barrier.
I suspect that in most cases the correct conversion would have been to
drop the barrier. I also suspect that a few cases exist where a) the
barrier was necessary and b) a second barrier before the atomic would
have been necessary and got added by this patch.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
atomic_inc_return() already does an implicit memory barrier and the
second case was moved from an atomic to a plain flag operation. If a
barrier were needed in the second case, it would have to be smp_mb(),
not a variant optimized away for x86 and other architectures.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
And while at it, do minimal coding style fixes in the area.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Simple and just called from one place.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove core_tpg_pre_dellun entirely, since we don't need to get/check
a pointer we already have.
Nothing else can return an error, so core_dev_del_lun can return void.
Rename core_tpg_post_dellun to remove_lun - a clearer name, now that
pre_dellun is gone.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Nothing in it can raise an error.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
With the recent addition of percpu_ref_reinit(), percpu_ref now can be
used as a persistent switch which can be turned on and off repeatedly
where turning off maps to killing the ref and waiting for it to drain;
however, there currently isn't a way to initialize a percpu_ref in its
off (killed and drained) state, which can be inconvenient for certain
persistent switch use cases.
Similarly, percpu_ref_switch_to_atomic/percpu() allow dynamic
selection of operation mode; however, currently a newly initialized
percpu_ref is always in percpu mode making it impossible to avoid the
latency overhead of switching to atomic mode.
This patch adds @flags to percpu_ref_init() and implements the
following flags.
* PERCPU_REF_INIT_ATOMIC : start ref in atomic mode
* PERCPU_REF_INIT_DEAD : start ref killed and drained
These flags should be able to serve the above two use cases.
v2: target_core_tpg.c conversion was missing. Fixed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
This is to receive 0a30288da1 ("blk-mq, percpu_ref: implement a
kludge for SCSI blk-mq stall during probe") which implements
__percpu_ref_kill_expedited() to work around SCSI blk-mq stall. The
commit reverted and patches to implement proper fix will be added.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@lst.de>
Clearly a right-shift was meant. Effectively doesn't make a difference,
as add_len is hard-coded to 8 and the high byte will be zero no matter
which way you shift. But I hate leaving bad examples for others to
copy.
Found by coverity.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch correctly handles match_int() errors in FILEIO + PSCSI
backend parameter parsing, which can potentially fail due to a
memory allocation failure or invalid argument.
Found by coverity.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Old code in iscsi_parse_pr_out_transport_id() was obviously buggy
and effectively ignored the high byte.
Found by coverity.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Coverity complained that lun_cg has been dereferenced in all paths
leading to NULL check. It didn't mention that only a single path could
lead there and the code can be simplified even further.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a memory leak on error in target_fabric_make_mappedlun(),
where se_lun_acl memory does not get released on exit.
Found by coverity.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Each case of match_strdup could leak memory if the same argument was
present before. I am not too concerned, as it would require a
non-sensical combination like "target_lun=foo target_lun=bar", done
with root privileges and even then leak just a few bytes per instance.
But arg_p is different, as it will always leak memory. Let's plug that
one. And while at it, replace some &args[0] with args.
Found by coverity.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
last_intr_fail_name is a fixed-size array and could theoretically
overflow. In reality intrname->value doesn't seem to depend on
untrusted input or be anywhere near 224 characters, so the overflow is
pretty theoretical. But strlcpy is cheap enough.
Found by coverity.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In iscsi_copy_param_list() a failed iscsi_param_list memory allocation
currently invokes iscsi_release_param_list() to cleanup, and will promptly
trigger a NULL pointer dereference.
Instead, go ahead and return for the first iscsi_copy_param_list()
failure case.
Found by coverity.
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug in iscsit_logout_post_handler_diffcid() where
a pointer used as storage for list_for_each_entry() was incorrectly
being used to determine if no matching entry had been found.
This patch changes iscsit_logout_post_handler_diffcid() to key off
bool conn_found to determine if the function needs to exit early.
Reported-by: Joern Engel <joern@logfs.org>
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Found by coverity. At this point sock is non-NULL, so the check
to unnecessary.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch drops the now duplicate + unnecessary check for -ENODEV from
iscsi_transport->iscsit_accept_np() for jumping to out:, or immediately
returning 1 in __iscsi_target_login_thread() code.
Since commit 81a9c5e72b the jump to out: and returning 1 have the same
effect, and end up hitting the ISCSI_NP_THREAD_SHUTDOWN check regardless
at the top of __iscsi_target_login_thread() during next loop iteration.
So that said, it's safe to go ahead and remove this duplicate check.
Reported-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The return statement cannot be reached without either recovery or dump
being set to 1. Therefore the condition always evaluates to true and
recovery and dump are useless variables.
Found by Coverity.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Found by coverity. InitiatorName and InitiatorAlias are static arrays
and therefore always non-NULL. At some point in the past they may have
been dynamically allocated, but for current code the condition is
useless. If the intent was to check InitiatorName[0] instead, I cannot
find a use for that either. Let's get rid of it.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Last user of buf was removed with c6037cc546. While at it,
free_cpumask_var() handles a NULL argument just fine, so remove the
conditionals.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fix inverted logic in SE_DEV_ALUA_SUPPORT_STATE_STORE for setting
the supported ALUA access states via configfs, originally introduced
in commit b0a382c5.
A value of 1 should enable the support, not disable it.
Signed-off-by: Sebastian Herbszt <herbszt@gmx.de>
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes an apparent cut and paste error in spc_emulate_evpd_b3(),
where lba_map_segment_size was being used twice for the Referrals VPD.
Go ahead and set the correct user data segment multiplier instead of
user data segment size.
Signed-off-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Clearly the file was meant to contain an include guard, but it was
missing the #define part.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The use of "rcu_assign_pointer()" is NULLing out the pointer.
According to RCU_INIT_POINTER()'s block comment:
"1. This use of RCU_INIT_POINTER() is NULLing out the pointer"
it is better to use it instead of rcu_assign_pointer() because it has a
smaller overhead.
The following Coccinelle semantic patch was used:
@@
@@
- rcu_assign_pointer
+ RCU_INIT_POINTER
(..., NULL)
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch removes the null test on lun_cg. lun_cg is initialized
at the beginning of the function to &lun->lun_group. Since lun_cg is
dereferenced prior to the null test, it must be a valid pointer.
The following Coccinelle script is used for detecting the change:
@r@
expression e,f;
identifier g,y;
statement S1,S2;
@@
*e = &f->g
<+...
f->y
...+>
*if (e != NULL || ...)
S1 else S2
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a explicit check in iscsit_find_cmd_from_itt_or_dump()
to ignore commands with ICF_GOT_LAST_DATAOUT set. This is done to
address the case where an ITT is being reused for DataOUT, but the
previous command with the same ITT has not yet been acknowledged by
ExpStatSN and removed from the per connection command list.
This issue was originally manifesting itself by referencing the
previous command during ITT lookup, and subsequently hitting the
check in iscsit_check_dataout_hdr() for ICF_GOT_LAST_DATAOUT, that
resulted in the DataOUT PDU + associated payload being silently
dumped.
Reported-by: Arshad Hussain <arshad.hussain@calsoftinc.com>
Tested-by: Arshad Hussain <arshad.hussain@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Percpu allocator now supports allocation mask. Add @gfp to
percpu_ref_init() so that !GFP_KERNEL allocation masks can be used
with percpu_refs too.
This patch doesn't make any functional difference.
v2: blk-mq conversion was missing. Updated.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Nicholas A. Bellinger <nab@linux-iscsi.org>
Cc: Jens Axboe <axboe@kernel.dk>
The blk_get_request function may fail in low-memory conditions or during
device removal (even if __GFP_WAIT is set). To distinguish between these
errors, modify the blk_get_request call stack to return the appropriate
ERR_PTR. Verify that all callers check the return status and consider
IS_ERR instead of a simple NULL pointer check.
For consistency, make a similar change to the blk_mq_alloc_request leg
of blk_get_request. It may fail if the queue is dead, or the caller was
unwilling to wait.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Jiri Kosina <jkosina@suse.cz> [for pktdvd]
Acked-by: Boaz Harrosh <bharrosh@panasas.com> [for osd]
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch set consists of the usual driver updates (ufs, storvsc, pm8001
hpsa). It also has removal of the user space target driver code (everyone is
using LIO now), a partial PCI MSI-X update, more multi-queue updates,
conversion to 64 bit LUNs (so we could theoretically cope with any LUN
returned by a device) and placeholder support for the ZBC device type (Shingle
drives), plus an assortment of minor updates and bug fixes.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJT4mS9AAoJEDeqqVYsXL0Mq34H/2AeXiM8GEVO3PIsBtF3TFZ9
poJvAyb8t//+VwAIVLHU9wrssIrIcyvNQmNHH/InGt5rOaXwGQRsnEc73bBtot4b
aC1t+hAnp2Ddvu6phmyUg7iY2GmQhAoZmeaj7krGIu2XgtLGiPg26eSsgk4Yv/U9
cuULEuOc/UnTj3w5VK8SvpyXMybVF6oQhSrS1slOglfFwPTlTI/NHU9xo7Wc3qHT
VifHXNphIvye5EH8zwtKX5p8qCrFW0pevJwyfPz7Hp2CTA9XYKx3SoeOh+n9F9ez
udBBggg7Vb1tb4mPKUoZ78UrtCVdFSCmesBU/RJe7cIh8daKaO5MVr3WPSx2JhM=
=yGai
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This patch set consists of the usual driver updates (ufs, storvsc,
pm8001 hpsa). It also has removal of the user space target driver
code (everyone is using LIO now), a partial PCI MSI-X update, more
multi-queue updates, conversion to 64 bit LUNs (so we could
theoretically cope with any LUN returned by a device) and placeholder
support for the ZBC device type (Shingle drives), plus an assortment
of minor updates and bug fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (143 commits)
scsi: do not issue SCSI RSOC command to Promise Vtrak E610f
vmw_pvscsi: Use pci_enable_msix_exact() instead of pci_enable_msix()
pm8001: Fix invalid return when request_irq() failed
lpfc: Remove superfluous call to pci_disable_msix()
isci: Use pci_enable_msix_exact() instead of pci_enable_msix()
bfa: Use pci_enable_msix_exact() instead of pci_enable_msix()
bfa: Cleanup bfad_setup_intr() function
bfa: Do not call pci_enable_msix() after it failed once
fnic: Use pci_enable_msix_exact() instead of pci_enable_msix()
scsi: use short driver name for per-driver cmd slab caches
scsi_debug: support scsi-mq, queues and locks
Drivers: add blist flags
scsi: ufs: fix endianness sparse warnings
scsi: ufs: make undeclared functions static
bnx2i: Update driver version to 2.7.10.1
pm8001: fix a memory leak in nvmd_resp
pm8001: fix update_flash
pm8001: fix a memory leak in flash_update
pm8001: Cleaning up uninitialized variables
pm8001: Fix to remove null pointer checks that could never happen
...
Pull percpu updates from Tejun Heo:
- Major reorganization of percpu header files which I think makes
things a lot more readable and logical than before.
- percpu-refcount is updated so that it requires explicit destruction
and can be reinitialized if necessary. This was pulled into the
block tree to replace the custom percpu refcnting implemented in
blk-mq.
- In the process, percpu and percpu-refcount got cleaned up a bit
* 'for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (21 commits)
percpu-refcount: implement percpu_ref_reinit() and percpu_ref_is_zero()
percpu-refcount: require percpu_ref to be exited explicitly
percpu-refcount: use unsigned long for pcpu_count pointer
percpu-refcount: add helpers for ->percpu_count accesses
percpu-refcount: one bit is enough for REF_STATUS
percpu-refcount, aio: use percpu_ref_cancel_init() in ioctx_alloc()
workqueue: stronger test in process_one_work()
workqueue: clear POOL_DISASSOCIATED in rebind_workers()
percpu: Use ALIGN macro instead of hand coding alignment calculation
percpu: invoke __verify_pcpu_ptr() from the generic part of accessors and operations
percpu: preffity percpu header files
percpu: use raw_cpu_*() to define __this_cpu_*()
percpu: reorder macros in percpu header files
percpu: move {raw|this}_cpu_*() definitions to include/linux/percpu-defs.h
percpu: move generic {raw|this}_cpu_*_N() definitions to include/asm-generic/percpu.h
percpu: only allow sized arch overrides for {raw|this}_cpu_*() ops
percpu: reorganize include/linux/percpu-defs.h
percpu: move accessors from include/linux/percpu.h to percpu-defs.h
percpu: include/asm-generic/percpu.h should contain only arch-overridable parts
percpu: introduce arch_raw_cpu_ptr()
...
The SCSI standard defines 64-bit values for LUNs, and large arrays
employing large or hierarchical LUN numbers become more and more
common.
So update the linux SCSI stack to use 64-bit LUN numbers.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Currently, a percpu_ref undoes percpu_ref_init() automatically by
freeing the allocated percpu area when the percpu_ref is killed.
While seemingly convenient, this has the following niggles.
* It's impossible to re-init a released reference counter without
going through re-allocation.
* In the similar vein, it's impossible to initialize a percpu_ref
count with static percpu variables.
* We need and have an explicit destructor anyway for failure paths -
percpu_ref_cancel_init().
This patch removes the automatic percpu counter freeing in
percpu_ref_kill_rcu() and repurposes percpu_ref_cancel_init() into a
generic destructor now named percpu_ref_exit(). percpu_ref_destroy()
is considered but it gets confusing with percpu_ref_kill() while
"exit" clearly indicates that it's the counterpart of
percpu_ref_init().
All percpu_ref_cancel_init() users are updated to invoke
percpu_ref_exit() instead and explicit percpu_ref_exit() calls are
added to the destruction path of all percpu_ref users.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Benjamin LaHaise <bcrl@kvack.org>
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: Nicholas A. Bellinger <nab@linux-iscsi.org>
Cc: Li Zefan <lizefan@huawei.com>
On uniprocessor preemptible kernel, target core deadlocks on unload. The
following events happen:
* iscsit_del_np is called
* it calls send_sig(SIGINT, np->np_thread, 1);
* the scheduler switches to the np_thread
* the np_thread is woken up, it sees that kthread_should_stop() returns
false, so it doesn't terminate
* the np_thread clears signals with flush_signals(current); and goes back
to sleep in iscsit_accept_np
* the scheduler switches back to iscsit_del_np
* iscsit_del_np calls kthread_stop(np->np_thread);
* the np_thread is waiting in iscsit_accept_np and it doesn't respond to
kthread_stop
The deadlock could be resolved if the administrator sends SIGINT signal to
the np_thread with killall -INT iscsi_np
The reproducible deadlock was introduced in commit
db6077fd0b, but the thread-stopping code was
racy even before.
This patch fixes the problem. Using kthread_should_stop to stop the
np_thread is unreliable, so we test np_thread_state instead. If
np_thread_state equals ISCSI_NP_THREAD_SHUTDOWN, the thread exits.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes iscsit_check_dataout_hdr() to dump the incoming
Data-Out payload when the received ITT is not associated with a
WRITE, instead of calling iscsit_reject_cmd() for the non WRITE
ITT descriptor.
This addresses a bug where an initiator sending an Data-Out for
an ITT associated with a READ would end up generating a reject
for the READ, eventually resulting in list corruption.
Reported-by: Santosh Kulkarni <santosh.kulkarni@calsoftinc.com>
Reported-by: Arshad Hussain <arshad.hussain@calsoftinc.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a tcm_loop_cmd descriptor memory leak in the
tcm_loop_submission_work() error path, and would result in
warnings about leaked tcm_loop_cmd_cache objects at module
unload time.
Go ahead and invoke kmem_cache_free() to release tl_cmd back to
tcm_loop_cmd_cache before calling sc->scsi_done().
Reported-by: Sebastian Herbszt <herbszt@gmx.de>
Tested-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a explicit memset to the login response PDU
exception path in iscsit_tx_login_rsp().
This addresses a regression bug introduced in commit baa4d64b
where the initiator would end up not receiving the login
response and associated status class + detail, before closing
the login connection.
Reported-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr>
Tested-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a left-over se_lun->lun_sep pointer OOPs when one
of the /sys/kernel/config/target/$FABRIC/$WWPN/$TPGT/lun/$LUN/alua*
attributes is accessed after the $DEVICE symlink has been removed.
To address this bug, go ahead and clear se_lun->lun_sep memory in
core_dev_unexport(), so that the existing checks for show/store
ALUA attributes in target_core_fabric_configfs.c work as expected.
Reported-by: Sebastian Herbszt <herbszt@gmx.de>
Tested-by: Sebastian Herbszt <herbszt@gmx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a check in chap_server_compute_md5() to enforce a
1024 byte maximum for the CHAP_C key value following the requirement
in RFC-3720 Section 11.1.4:
"..., C and R are large-binary-values and their binary length (not
the length of the character string that represents them in encoded
form) MUST not exceed 1024 bytes."
Reported-by: rahul.rane <rahul.rane@calsoftinc.com>
Tested-by: rahul.rane <rahul.rane@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts chap_server_compute_md5() from simple_strtoul() to
kstrtoul usage().
This addresses the case where a empty 'CHAP_I=' key value received during
mutual authentication would be converted to a '0' by simple_strtoul(),
instead of failing the login attempt.
Reported-by: Tejas Vaykole <tejas.vaykole@calsoftinc.com>
Tested-by: Tejas Vaykole <tejas.vaykole@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- Add support for T10 PI pass-through between vhost-scsi +
virtio-scsi (MST + Paolo + MKP + nab)
- Add support for T10 PI in qla2xxx target mode (Quinn + MKP + hch +
nab, merged through scsi.git)
- Add support for percpu-ida pre-allocation in qla2xxx target code
(Quinn + nab)
- A number of iser-target fixes related to hardening the network
portal shutdown path (Sagi + Slava)
- Fix response length residual handling for a number of control CDBs
(Roland + Christophe V.)
- Various iscsi RFC conformance fixes in the CHAP authentication path
(Tejas and Calsoft folks + nab)
- Return TASK_SET_FULL status for tcm_fc(FCoE) DataIn + Response
failures (Vasu + Jun + nab)
- Fix long-standing ABORT_TASK + session reset hang (nab)
- Convert iser-initiator + iser-target to include T10 bytes into EDTL
(Sagi + Or + MKP + Mike Christie)
- Fix NULL pointer dereference regression related to XCOPY introduced
in v3.15 + CC'ed to v3.12.y (nab)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (34 commits)
target: Fix NULL pointer dereference for XCOPY in target_put_sess_cmd
vhost-scsi: Include prot_bytes into expected data transfer length
TARGET/sbc,loopback: Adjust command data length in case pi exists on the wire
libiscsi, iser: Adjust data_length to include protection information
scsi_cmnd: Introduce scsi_transfer_length helper
target: Report correct response length for some commands
target/sbc: Check that the LBA and number of blocks are correct in VERIFY
target/sbc: Remove sbc_check_valid_sectors()
Target/iscsi: Fix sendtargets response pdu for iser transport
Target/iser: Fix a wrong dereference in case discovery session is over iser
iscsi-target: Fix ABORT_TASK + connection reset iscsi_queue_req memory leak
target: Use complete_all for se_cmd->t_transport_stop_comp
target: Set CMD_T_ACTIVE bit for Task Management Requests
target: cleanup some boolean tests
target/spc: Simplify INQUIRY EVPD=0x80
tcm_fc: Generate TASK_SET_FULL status for response failures
tcm_fc: Generate TASK_SET_FULL status for DataIN failures
iscsi-target: Reject mutual authentication with reflected CHAP_C
iscsi-target: Remove no-op from iscsit_tpg_del_portal_group
iscsi-target: Fix CHAP_A parameter list handling
...
This patch fixes a NULL pointer dereference regression bug that was
introduced with:
commit 1e1110c43b
Author: Mikulas Patocka <mpatocka@redhat.com>
Date: Sat May 17 06:49:22 2014 -0400
target: fix memory leak on XCOPY
Now that target_put_sess_cmd() -> kref_put_spinlock_irqsave() is
called with a valid se_cmd->cmd_kref, a NULL pointer dereference
is triggered because the XCOPY passthrough commands don't have
an associated se_session pointer.
To address this bug, go ahead and checking for a NULL se_sess pointer
within target_put_sess_cmd(), and call se_cmd->se_tfo->release_cmd()
to release the XCOPY's xcopy_pt_cmd memory.
Reported-by: Thomas Glanzmann <thomas@glanzmann.de>
Cc: Thomas Glanzmann <thomas@glanzmann.de>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org # 3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In various areas of the code, it is assumed that
se_cmd->data_length describes pure data. In case
that protection information exists over the wire
(protect bits is are on) the target core re-calculates
the data length from the CDB and the backed device
block size (instead of each transport peeking in the cdb).
Modify loopback device to include protection information
in the transferred data length (like other scsi transports).
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: stable@vger.kernel.org # 3.15+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When an initiator sends an allocation length bigger than what its
command consumes, the target should only return the actual response data
and set the residual length to the unused part of the allocation length.
Add a helper function that command handlers (INQUIRY, READ CAPACITY,
etc) can use to do this correctly, and use this code to get the correct
residual for commands that don't use the full initiator allocation in the
handlers for READ CAPACITY, READ CAPACITY(16), INQUIRY, MODE SENSE and
REPORT LUNS.
This addresses a handful of failures as reported by Christophe with
the Windows Certification Kit:
http://permalink.gmane.org/gmane.linux.scsi.target.devel/6515
Signed-off-by: Roland Dreier <roland@purestorage.com>
Tested-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch extracts LBA + sectors for VERIFY, and adds a goto check_lba
to perform the end-of-device checking.
(Update patch to drop lba_check usage - nab)
Signed-off-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
A similar check is performed at the end of sbc_parse_cdb() and is now
enforced if the SYNCHRONIZE CACHE command's backend supports
->execute_sync_cache().
(Add check_lba goto to avoid *_max_sectors checks - nab)
Signed-off-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In case the transport is iser we should not include the
iscsi target info in the sendtargets text response pdu.
This causes sendtargets response to include the target
info twice.
Modify iscsit_build_sendtargets_response to filter
transport types that don't match.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reported-by: Slava Shwartsman <valyushash@gmail.com>
Cc: stable@vger.kernel.org # 3.11+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull block layer fixes from Jens Axboe:
"Final small batch of fixes to be included before -rc1. Some general
cleanups in here as well, but some of the blk-mq fixes we need for the
NVMe conversion and/or scsi-mq. The pull request contains:
- Support for not merging across a specified "chunk size", if set by
the driver. Some NVMe devices perform poorly for IO that crosses
such a chunk, so we need to support it generically as part of
request merging avoid having to do complicated split logic. From
me.
- Bump max tag depth to 10Ki tags. Some scsi devices have a huge
shared tag space. Before we failed with EINVAL if a too large tag
depth was specified, now we truncate it and pass back the actual
value. From me.
- Various blk-mq rq init fixes from me and others.
- A fix for enter on a dying queue for blk-mq from Keith. This is
needed to prevent oopsing on hot device removal.
- Fixup for blk-mq timer addition from Ming Lei.
- Small round of performance fixes for mtip32xx from Sam Bradshaw.
- Minor stack leak fix from Rickard Strandqvist.
- Two __init annotations from Fabian Frederick"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: add __init to blkcg_policy_register
block: add __init to elv_register
block: ensure that bio_add_page() always accepts a page for an empty bio
blk-mq: add timer in blk_mq_start_request
blk-mq: always initialize request->start_time
block: blk-exec.c: Cleaning up local variable address returnd
mtip32xx: minor performance enhancements
blk-mq: ->timeout should be cleared in blk_mq_rq_ctx_init()
blk-mq: don't allow queue entering for a dying queue
blk-mq: bump max tag depth to 10K tags
block: add blk_rq_set_block_pc()
block: add notion of a chunk size for request merging
This patch fixes a iscsi_queue_req memory leak when ABORT_TASK response
has been queued by TFO->queue_tm_rsp() -> lio_queue_tm_rsp() after a
long standing I/O completes, but the connection has already reset and
waiting for cleanup to complete in iscsit_release_commands_from_conn()
-> transport_generic_free_cmd() -> transport_wait_for_tasks() code.
It moves iscsit_free_queue_reqs_for_conn() after the per-connection command
list has been released, so that the associated se_cmd tag can be completed +
released by target-core before freeing any remaining iscsi_queue_req memory
for the connection generated by lio_queue_tm_rsp().
Cc: Thomas Glanzmann <thomas@glanzmann.de>
Cc: Charalampos Pournaris <charpour@gmail.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug where multiple waiters on ->t_transport_stop_comp
occurs due to a concurrent ABORT_TASK and session reset both invoking
transport_wait_for_tasks(), while waiting for the associated se_cmd
descriptor backend processing to complete.
For this case, complete_all() should be invoked in order to wake up
both waiters in core_tmr_abort_task() + transport_generic_free_cmd()
process contexts.
Cc: Thomas Glanzmann <thomas@glanzmann.de>
Cc: Charalampos Pournaris <charpour@gmail.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug where se_cmd descriptors associated with a
Task Management Request (TMR) where not setting CMD_T_ACTIVE before
being dispatched into target_tmr_work() process context.
This is required in order for transport_generic_free_cmd() ->
transport_wait_for_tasks() to wait on se_cmd->t_transport_stop_comp
if a session reset event occurs while an ABORT_TASK is outstanding
waiting for another I/O to complete.
Cc: Thomas Glanzmann <thomas@glanzmann.de>
Cc: Charalampos Pournaris <charpour@gmail.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that 3.15 is released, this merges the 'next' branch into 'master',
bringing us to the normal situation where my 'master' branch is the
merge window.
* accumulated work in next: (6809 commits)
ufs: sb mutex merge + mutex_destroy
powerpc: update comments for generic idle conversion
cris: update comments for generic idle conversion
idle: remove cpu_idle() forward declarations
nbd: zero from and len fields in NBD_CMD_DISCONNECT.
mm: convert some level-less printks to pr_*
MAINTAINERS: adi-buildroot-devel is moderated
MAINTAINERS: add linux-api for review of API/ABI changes
mm/kmemleak-test.c: use pr_fmt for logging
fs/dlm/debug_fs.c: replace seq_printf by seq_puts
fs/dlm/lockspace.c: convert simple_str to kstr
fs/dlm/config.c: convert simple_str to kstr
mm: mark remap_file_pages() syscall as deprecated
mm: memcontrol: remove unnecessary memcg argument from soft limit functions
mm: memcontrol: clean up memcg zoneinfo lookup
mm/memblock.c: call kmemleak directly from memblock_(alloc|free)
mm/mempool.c: update the kmemleak stack trace for mempool allocations
lib/radix-tree.c: update the kmemleak stack trace for radix tree allocations
mm: introduce kmemleak_update_trace()
mm/kmemleak.c: use %u to print ->checksum
...
Convert "x == true" to "x" and "x == false" to "!x".
Signed-off-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes ft_queue_status() to set SAM_STAT_TASK_SET_FULL
status upon lport->tt.seq_send( failure, and return -EAGAIN to notify
target-core to attempt to requeue the response.
It also does the same for a fc_frame_alloc() failures, in order to
signal the initiator that it should try to reduce it's current
queue_depth, to lower the number of outstanding I/Os on the wire.
Reported-by: Vasu Dev <vasu.dev@linux.intel.com>
Reviewed-by: Vasu Dev <vasu.dev@linux.intel.com>
Cc: Jun Wu <jwu@stormojo.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes ft_queue_data_in() to set SAM_STAT_TASK_SET_FULL
status upon a lport->tt.seq_send() failure, where it will now stop
sending subsequent DataIN, and immediately attempt to send the
response with exception status.
Sending a response with SAM_STAT_TASK_SET_FULL status is useful in
order to signal the initiator that it should try to reduce it's
current queue_depth, to lower the number of outstanding I/Os on
the wire.
Also, add a check to skip sending DataIN if TASK_SET_FULL status
has already been set due to a response lport->tt.seq_send()
failure, that has asked target-core to requeue a response.
Reported-by: Vasu Dev <vasu.dev@linux.intel.com>
Reviewed-by: Vasu Dev <vasu.dev@linux.intel.com>
Cc: Jun Wu <jwu@stormojo.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
With the optimizations around not clearing the full request at alloc
time, we are leaving some of the needed init for REQ_TYPE_BLOCK_PC
up to the user allocating the request.
Add a blk_rq_set_block_pc() that sets the command type to
REQ_TYPE_BLOCK_PC, and properly initializes the members associated
with this type of request. Update callers to use this function instead
of manipulating rq->cmd_type directly.
Includes fixes from Christoph Hellwig <hch@lst.de> for my half-assed
attempt.
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch fixes a OOPs where an attempt to write to the per-device
alua_access_state configfs attribute at:
/sys/kernel/config/target/core/$HBA/$DEV/alua/$TG_PT_GP/alua_access_state
results in an NULL pointer dereference when the backend device has not
yet been configured.
This patch adds an explicit check for DF_CONFIGURED, and fails with
-ENODEV to avoid this case.
Reported-by: Chris Boot <crb@tiger-computing.co.uk>
Reported-by: Philip Gaw <pgaw@darktech.org.uk>
Cc: Chris Boot <crb@tiger-computing.co.uk>
Cc: Philip Gaw <pgaw@darktech.org.uk>
Cc: stable@vger.kernel.org # 3.8+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch allows READ_CAPACITY + SAI_READ_CAPACITY_16 opcode
processing to occur while the associated ALUA group is in Standby
access state.
This is required to avoid host side LUN probe failures during the
initial scan if an ALUA group has already implicitly changed into
Standby access state.
This addresses a bug reported by Chris + Philip using dm-multipath
+ ESX hosts configured with ALUA multipath.
Reported-by: Chris Boot <crb@tiger-computing.co.uk>
Reported-by: Philip Gaw <pgaw@darktech.org.uk>
Cc: Chris Boot <crb@tiger-computing.co.uk>
Cc: Philip Gaw <pgaw@darktech.org.uk>
Cc: Hannes Reinecke <hare@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds an explicit check in chap_server_compute_md5() to ensure
the CHAP_C value received from the initiator during mutual authentication
does not match the original CHAP_C provided by the target.
This is in line with RFC-3720, section 8.2.1:
Originators MUST NOT reuse the CHAP challenge sent by the Responder
for the other direction of a bidirectional authentication.
Responders MUST check for this condition and close the iSCSI TCP
connection if it occurs.
Reported-by: Tejas Vaykole <tejas.vaykole@calsoftinc.com>
Cc: stable@vger.kernel.org # 3.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch removes a no-op iscsit_clear_tpg_np_login_threads() call
in iscsit_tpg_del_portal_group(), which is unnecessary because
iscsit_tpg_del_portal_group() can only ever be removed from configfs
once all of the child network portals have been released.
Also, go ahed and make iscsit_clear_tpg_np_login_threads() declared
as static.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The target is failing to handle list of CHAP_A key-value pair form
initiator.The target is expecting CHAP_A=5 always. In other cases,
where initiator sends list (for example) CHAP_A=6,5 target is failing
the security negotiation. Which is incorrect.
This patch handles the case (RFC 3720 section 11.1.4).
where in the initiator may send list of CHAP_A values and target replies
with appropriate CHAP_A value in response
(Drop whitespaces + rename to chap_check_algorithm + save original
pointer + add explicit check for CHAP_A key - nab)
Signed-off-by: Tejas Vaykole <tejas.vaykole@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If the message "Unable to allocate…" pops up, it's useful to know
whether the problem is that the system is genuinely out of memory, or
that some bug has led to a crazy allocation length.
In particular this helped debug a corruption of login headers in
iscsi_login_non_zero_tsih_s1().
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes iscsi_target_handle_csg_zero() to explicitly
reject login requests in SecurityNegotiation with a zero-length
payload, following the language in RFC-3720 Section 8.2:
Whenever an iSCSI target gets a response whose keys, or their
values, are not according to the step definition, it MUST answer
with a Login reject with the "Initiator Error" or "Missing Parameter"
status.
Previously when a zero-length login request in CSG=0 was received,
the target would send a login response with CSG=0 + T_BIT=0 asking
the initiator to complete authentication, and not fail the login
until MAX_LOGIN_PDUS was reached. This change will now immediately
fail the login attempt with ISCSI_STATUS_CLS_INITIATOR_ERR status.
Reported-by: Tejas Vaykole <tejas.vaykole@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a iser-target specific regression introduced in
v3.15-rc6 with:
commit 14f4b54fe3
Author: Sagi Grimberg <sagig@mellanox.com>
Date: Tue Apr 29 13:13:47 2014 +0300
Target/iscsi,iser: Avoid accepting transport connections during stop stage
where the change to set iscsi_np->enabled = false within
iscsit_clear_tpg_np_login_thread() meant that a iscsi_np with
two iscsi_tpg_np exports would have it's parent iscsi_np set
to a disabled state, even if other iscsi_tpg_np exports still
existed.
This patch changes iscsit_clear_tpg_np_login_thread() to only
set iscsi_np->enabled = false when shutdown = true, and also
changes iscsit_del_np() to set iscsi_np->enabled = true when
iscsi_np->np_exports is non zero.
Cc: Sagi Grimberg <sagig@dev.mellanox.co.il>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In non-leading connection login, iscsi_login_non_zero_tsih_s1() calls
iscsi_change_param_value() with the buffer it uses to hold the login
PDU, not a temporary buffer. This leads to the login header getting
corrupted and login failing for non-leading connections in MC/S.
Fix this by adding a wrapper iscsi_change_param_sprintf() that handles
the temporary buffer itself to avoid confusion. Also handle sending a
reject in case of failure in the wrapper, which lets the calling code
get quite a bit smaller and easier to read.
Finally, bump the size of the temporary buffer from 32 to 64 bytes to be
safe, since "MaxRecvDataSegmentLength=" by itself is 25 bytes; with a
trailing NUL, a value >= 1M will lead to a buffer overrun. (This isn't
the default but we don't need to run right at the ragged edge here)
Reported-by: Santosh Kulkarni <santosh.kulkarni@calsoftinc.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
On each processed XCOPY command, two "kmalloc-512" memory objects are
leaked. These represent two allocations of struct xcopy_pt_cmd in
target_core_xcopy.c.
The reason for the memory leak is that the cmd_kref field is not
initialized (thus, it is zero because the allocations were done with
kzalloc). When we decrement zero kref in target_put_sess_cmd, the result
is not zero, thus target_release_cmd_kref is not called.
This patch fixes the bug by moving kref initialization from
target_get_sess_cmd to transport_init_se_cmd (this function is called from
target_core_xcopy.c, so it will correctly initialize cmd_kref). It can be
easily verified that all code that calls target_get_sess_cmd also calls
transport_init_se_cmd earlier, thus moving kref_init shouldn't introduce
any new problems.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org # 3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Just like for pSCSI, if the transport sets get_write_cache, then it is
not valid to enable write cache emulation for it. Return an error.
see https://bugzilla.redhat.com/show_bug.cgi?id=1082675
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Andy Grover <agrover@redhat.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch explicitly disables Immediate + Unsolicited Data for ISER
connections during login in iscsi_login_zero_tsih_s2() when protection
has been enabled for the session by the underlying hardware.
This is currently required because protection / signature memory regions
(MRs) expect T10 PI to occur on RDMA READs + RDMA WRITEs transfers, and
not on a immediate data payload associated with ISCSI_OP_SCSI_CMD, or
unsolicited data-out associated with a ISCSI_OP_SCSI_DATA_OUT.
v2 changes:
- Add TARGET_PROT_DOUT_INSERT check (Sagi)
- Add pr_debug noisemaker (Sagi)
- Add goto to avoid early return from MRDSL check (nab)
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a free-after-use regression in ft_free_cmd(), where
ft_sess_put() is called with cmd->sess after percpu_ida_free() has
already released the tag.
Fix this bug by saving the ft_sess pointer ahead of percpu_ida_free(),
and pass it directly to ft_sess_put().
The regression was originally introduced in v3.13-rc1 commit:
commit 5f544cfac9
Author: Nicholas Bellinger <nab@daterainc.com>
Date: Mon Sep 23 12:12:42 2013 -0700
tcm_fc: Convert to per-cpu command map pre-allocation of ft_cmd
Reported-by: Jun Wu <jwu@stormojo.com>
Cc: Mark Rustad <mark.d.rustad@intel.com>
Cc: Robert Love <robert.w.love@intel.com>
Cc: <stable@vger.kernel.org> #3.13+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes an incorrect use of BUG_ON to instead generate a
REJECT + PROTOCOL_ERROR in iscsit_process_nop_out() code. This case
can occur with traditional TCP where a flood of zeros in the data
stream can reach this block for what is presumed to be a NOP-OUT with
a solicited reply, but without a valid iscsi_cmd pointer.
This incorrect BUG_ON was introduced during the v3.11-rc timeframe
with the following commit:
commit 778de36896
Author: Nicholas Bellinger <nab@linux-iscsi.org>
Date: Fri Jun 14 16:07:47 2013 -0700
iscsi/isert-target: Refactor ISCSI_OP_NOOP RX handling
Reported-by: Arshad Hussain <arshad.hussain@calsoftinc.com>
Cc: stable@vger.kernel.org # 3.11+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When the target is in stop stage, iSER transport initiates RDMA disconnects.
The iSER initiator may wish to establish a new connection over the
still existing network portal. In this case iSER transport should not
accept and resume new RDMA connections. In order to learn that, iscsi_np
is added with enabled flag so the iSER transport can check when deciding
weather to accept and resume a new connection request.
The iscsi_np is enabled after successful transport setup, and disabled
before iscsi_np login threads are cleaned up.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Userspace tools assume if a value is read from configfs, it is valid
and will not cause an error if the same value is written back. The only
valid value for pi_prot_type for backends not supporting DIF is 0, so allow
this particular value to be set without returning an error.
Reported-by: Krzysztof Chojnowski <frirajder@gmail.com>
Signed-off-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull yet more networking updates from David Miller:
1) Various fixes to the new Redpine Signals wireless driver, from
Fariya Fatima.
2) L2TP PPP connect code takes PMTU from the wrong socket, fix from
Dmitry Petukhov.
3) UFO and TSO packets differ in whether they include the protocol
header in gso_size, account for that in skb_gso_transport_seglen().
From Florian Westphal.
4) If VLAN untagging fails, we double free the SKB in the bridging
output path. From Toshiaki Makita.
5) Several call sites of sk->sk_data_ready() were referencing an SKB
just added to the socket receive queue in order to calculate the
second argument via skb->len. This is dangerous because the moment
the skb is added to the receive queue it can be consumed in another
context and freed up.
It turns out also that none of the sk->sk_data_ready()
implementations even care about this second argument.
So just kill it off and thus fix all these use-after-free bugs as a
side effect.
6) Fix inverted test in tcp_v6_send_response(), from Lorenzo Colitti.
7) pktgen needs to do locking properly for LLTX devices, from Daniel
Borkmann.
8) xen-netfront driver initializes TX array entries in RX loop :-) From
Vincenzo Maffione.
9) After refactoring, some tunnel drivers allow a tunnel to be
configured on top itself. Fix from Nicolas Dichtel.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (46 commits)
vti: don't allow to add the same tunnel twice
gre: don't allow to add the same tunnel twice
drivers: net: xen-netfront: fix array initialization bug
pktgen: be friendly to LLTX devices
r8152: check RTL8152_UNPLUG
net: sun4i-emac: add promiscuous support
net/apne: replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
net: ipv6: Fix oif in TCP SYN+ACK route lookup.
drivers: net: cpsw: enable interrupts after napi enable and clearing previous interrupts
drivers: net: cpsw: discard all packets received when interface is down
net: Fix use after free by removing length arg from sk_data_ready callbacks.
Drivers: net: hyperv: Address UDP checksum issues
Drivers: net: hyperv: Negotiate suitable ndis version for offload support
Drivers: net: hyperv: Allocate memory for all possible per-pecket information
bridge: Fix double free and memory leak around br_allowed_ingress
bonding: Remove debug_fs files when module init fails
i40evf: program RSS LUT correctly
i40evf: remove open-coded skb_cow_head
ixgb: remove open-coded skb_cow_head
igbvf: remove open-coded skb_cow_head
...
Because it doesn't always create, if there's an existing one it just
returns it.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
These functions are not adding or deleting an lport. They are adding a
wwn that may match with an lport that is present on the system.
Renaming ft_del_lport also means we won't have functions named
both ft_del_lport and ft_lport_del any more.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Rename struct ft_lport_acl to ft_lport_wwn. "acl" is associated with
something different in LIO terms. Really, ft_lport_wwn is the
fabric-specific wrapper for the struct se_wwn.
Rename "lacl" local variables to "ft_wwn" as well.
Rename list_heads used as list members to make it clear they're nodes, not
heads.
Rename lport_node to ft_wwn_node.
Rename ft_lport_list to ft_wwn_list
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
tcm_fc doesn't support multiple TPGs per wwn. For proof, see
ft_lport_find_tpg. Enforce this in the code.
Replace ft_lport_wwn.tpg_list with a single pointer. We can't fold ft_tpg
into ft_lport_wwn because they can have different lifetimes.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
ft_del_tpg checks tpg->tport is set before unlinking the tpg from the
tport when the tpg is being removed. Set this pointer in ft_tport_create,
or the unlinking won't happen in ft_del_tpg and tport->tpg will reference
a deleted object.
This patch sets tpg->tport in ft_tport_create, because that's what
ft_del_tpg checks, and is the only way to get back to the tport to
clear tport->tpg.
The bug was occuring when:
- lport created, tport (our per-lport, per-provider context) is
allocated.
tport->tpg = NULL
- tpg created
- a PRLI is received. ft_tport_create is called, tpg is found and
tport->tpg is set
- tpg removed. ft_tpg is freed in ft_del_tpg. Since tpg->tport was not
set, tport->tpg is not cleared and points at freed memory
- Future calls to ft_tport_create return tport via first conditional,
instead of searching for new tpg by calling ft_lport_find_tpg.
tport->tpg is still invalid, and will access freed memory.
see https://bugzilla.redhat.com/show_bug.cgi?id=1071340
Cc: stable@vger.kernel.org # 3.0+
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses an issue that occurs when an ABTS is received
for an se_cmd that completes just before the sess_cmd_list is searched
in core_tmr_abort_task(). When the sess_cmd_list is searched, since
the ABTS and the FCP_CMND being aborted (that just completed) both
have the same OXID, TFO->get_task_tag(TMR) returns a value that
matches tmr->ref_task_tag (from TFO->get_task_tag(FCP_CMND)), and
the Abort Task tries to abort itself. When this occurs,
transport_wait_for_tasks() hangs forever since the TMR is waiting
for itself to finish.
This patch adds a check to core_tmr_abort_task() to make sure the
TMR does not attempt to abort itself.
Signed-off-by: Alex Leung <alex.leung@emulex.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Several spots in the kernel perform a sequence like:
skb_queue_tail(&sk->s_receive_queue, skb);
sk->sk_data_ready(sk, skb->len);
But at the moment we place the SKB onto the socket receive queue it
can be consumed and freed up. So this skb->len access is potentially
to freed up memory.
Furthermore, the skb->len can be modified by the consumer so it is
possible that the value isn't accurate.
And finally, no actual implementation of this callback actually uses
the length argument. And since nobody actually cared about it's
value, lots of call sites pass arbitrary values in such as '0' and
even '1'.
So just remove the length argument from the callback, that way there
is no confusion whatsoever and all of these use-after-free cases get
fixed as a side effect.
Based upon a patch by Eric Dumazet and his suggestion to audit this
issue tree-wide.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables the use of READ_STRIP software emulation in
target_complete_ok_work() code for I/O READs.
This is useful when the fabric does not support READ_STRIP hardware
offload, but would still like to interact with backend device
that have T10 PI enabled.
v2 changes:
- Move TARGET_PROT_DIN_STRIP check from target_check_read_strip()
into target_complete_ok_work() (Sagi)
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Split up __sbc_dif_verify_read() so that VERIFY READ emulation can
perform target-core specific READ_STRIP, seperate from the existing
FILEIO/RAMDISK backend emulation code.
Also add sbc_dif_read_strip() in order to determine number of sectors
using cmd->prot_length, and skip the extra sbc_dif_copy_prot().
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch enables WRITE_INSERT emulation in target_execute_cmd()
in order to locally generate DIF PI before submitting the WRITE
to the underlying backend device.
This is required for fabric drivers that currently don't support
DIF over-the-wire, in order to inact with backend devices that
have hardware (IBLOCK) or software (FILEIO + RAMDISK) support
for handling T10 PI.
v2 changes:
- Convert to sbc_dif_generate() usage (Sagi)
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds WRITE_INSERT emulation within target-core
using TYPE1 / TYPE3 PI modes in sbc_dif_generate() code.
This is useful in order for existing legacy fabrics that do not
support protection offloads to interact with backend devices that
currently have T10 PI enabled.
v2 changes:
- Rename to sbc_dif_generate() (Sagi)
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
