Pipeline handling calculations in idetape_calculate_speeds() can
go since they do not have any effect on other functionality besides:
1. info is only being exported through /proc as a read-only item
(controlled_pipeline_head_speed, uncontrolled_pipeline_head_speed)
2. used in idetape_restart_speed_control() which, in turn, is unrelated to
other code
3. used only for pipeline frames number accounting (tape->pipeline_head),
also unused elsewhere.
4.some variables are:
only written to: tape->buffer_head;
unused: tape->tape_head, tape->last_tape_head
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Refrain from adding more write requests to the pipeline and queue them
directly on the device's request queue instead.
[bart: re-do for minimal behavior changes]
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Prior to allocating a new pipeline stage, the code checked for the existence of
a cached pipeline stage to use. Do away with and stick to normal pipeline
stages only.
[bart: keep idetape_kmalloc_stage() for now]
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove obsoleted "hdx=noautotune" kernel parameter
(it has been obsoleted since 1 Nov 2004).
Then make ide_hwif_t.autotune a single bit flag
and remove no longer needed IDE_TUNE_* defines.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove obsoleted "idex=reset" kernel parameter
(it has been obsoleted since 1 Nov 2004).
Then remove corresponding code from ide_probe_port()
and no longer used ->reset field from ide_hwif_t.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove obsoleted "idex=serialize" kernel parameter
(it has been obsoleted since 1 Nov 2004).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add "ignore_cable" parameter:
* "ide_core.ignore_cable=[interface_number]" boot option if IDE is built-in
(i.e. "ide_core.ignore_cable=1" to force ignoring cable for "ide1")
* "ignore_cable=[interface_number]" module parameter (for ide_core module)
if IDE is compiled as module
v2:
* Add ide_port_apply_params() helper
- use it in ide_device_add_all() and ide_scan_port().
* Make it possible to later disable ignoring cable detection by passing
"[interface_number]:0" to /sys/module/ide_core/parameters/ignore_cable
(however sysfs interface is not enabled yet since it needs some other
IDE changes to make it work reliable).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fallout from commit ac95beedf8
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86-bigbox-bootmem-v3:
x86_64/mm: check and print vmemmap allocation continuous
x86_64: fix setup_node_bootmem to support big mem excluding with memmap
x86_64: make reserve_bootmem_generic() use new reserve_bootmem()
mm: allow reserve_bootmem() cross nodes
mm: offset align in alloc_bootmem()
mm: fix alloc_bootmem_core to use fast searching for all nodes
mm: make mem_map allocation continuous
On big systems with lots of memory, don't print out too much during
bootup, and make it easy to find if it is continuous.
on 256G 8 sockets system will get
[ffffe20000000000-ffffe20002bfffff] PMD -> [ffff810001400000-ffff810003ffffff] on node 0
[ffffe2001c700000-ffffe2001c7fffff] potential offnode page_structs
[ffffe20002c00000-ffffe2001c7fffff] PMD -> [ffff81000c000000-ffff8100255fffff] on node 0
[ffffe20038700000-ffffe200387fffff] potential offnode page_structs
[ffffe2001c800000-ffffe200387fffff] PMD -> [ffff810820200000-ffff81083c1fffff] on node 1
[ffffe20040000000-ffffe2007fffffff] PUD ->ffff811027a00000 on node 2
[ffffe20038800000-ffffe2003fffffff] PMD -> [ffff811020200000-ffff8110279fffff] on node 2
[ffffe20054700000-ffffe200547fffff] potential offnode page_structs
[ffffe20040000000-ffffe200547fffff] PMD -> [ffff811027c00000-ffff81103c3fffff] on node 2
[ffffe20070700000-ffffe200707fffff] potential offnode page_structs
[ffffe20054800000-ffffe200707fffff] PMD -> [ffff811820200000-ffff81183c1fffff] on node 3
[ffffe20080000000-ffffe200bfffffff] PUD ->ffff81202fa00000 on node 4
[ffffe20070800000-ffffe2007fffffff] PMD -> [ffff812020200000-ffff81202f9fffff] on node 4
[ffffe2008c700000-ffffe2008c7fffff] potential offnode page_structs
[ffffe20080000000-ffffe2008c7fffff] PMD -> [ffff81202fc00000-ffff81203c3fffff] on node 4
[ffffe200a8700000-ffffe200a87fffff] potential offnode page_structs
[ffffe2008c800000-ffffe200a87fffff] PMD -> [ffff812820200000-ffff81283c1fffff] on node 5
[ffffe200c0000000-ffffe200ffffffff] PUD ->ffff813037a00000 on node 6
[ffffe200a8800000-ffffe200bfffffff] PMD -> [ffff813020200000-ffff8130379fffff] on node 6
[ffffe200c4700000-ffffe200c47fffff] potential offnode page_structs
[ffffe200c0000000-ffffe200c47fffff] PMD -> [ffff813037c00000-ffff81303c3fffff] on node 6
[ffffe200c4800000-ffffe200e07fffff] PMD -> [ffff813820200000-ffff81383c1fffff] on node 7
instead of a very long print out...
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
typical case: four sockets system, every node has 4g ram, and we are using:
memmap=10g$4g
to mask out memory on node1 and node2
when numa is enabled, early_node_mem is used to get node_data and node_bootmap.
if it can not get memory from the same node with find_e820_area(), it will
use alloc_bootmem to get buff from previous nodes.
so check it and print out some info about it.
need to move early_res_to_bootmem into every setup_node_bootmem.
and it takes range that node has. otherwise alloc_bootmem could return addr
that reserved early.
depends on "mm: make reserve_bootmem can crossed the nodes".
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
"mm: make reserve_bootmem can crossed the nodes" provides new
reserve_bootmem(), let reserve_bootmem_generic() use that.
reserve_bootmem_generic() is used to reserve initramdisk, so this way
we can make sure even when bootloader or kexec load ranges cross the
node memory boundaries, reserve_bootmem still works.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
split reserve_bootmem_core() into two functions, one which checks
conflicts, and one which sets the bits.
and make reserve_bootmem to loop bdata_list to cross the nodes.
user could be crashkernel and ramdisk..., in case the range provided
by those externalities crosses the nodes.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
need offset alignment when node_boot_start's alignment is less than
the alignment required.
use local node_boot_start to match alignment - so don't add extra operation
in search loop.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Make the nodes other than node 0 use bdata->last_success for fast
search too.
We need to use __alloc_bootmem_core() for vmemmap allocation for other
nodes when numa and sparsemem/vmemmap are enabled.
Also, make fail_block path increase i with incr only after ALIGN
to avoid extra increase when size is larger than align.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
vmemmap allocation currently has this layout:
[ffffe20000000000-ffffe200001fffff] PMD ->ffff810001400000 on node 0
[ffffe20000200000-ffffe200003fffff] PMD ->ffff810001800000 on node 0
[ffffe20000400000-ffffe200005fffff] PMD ->ffff810001c00000 on node 0
[ffffe20000600000-ffffe200007fffff] PMD ->ffff810002000000 on node 0
[ffffe20000800000-ffffe200009fffff] PMD ->ffff810002400000 on node 0
...
note that there is a 2M hole between them - not optimal.
the root cause is that usemap (24 bytes) will be allocated after every 2M
mem_map, and it will push next vmemmap (2M) to the next (2M) alignment.
solution: try to allocate the mem_map continously.
after the patch, we get:
[ffffe20000000000-ffffe200001fffff] PMD ->ffff810001400000 on node 0
[ffffe20000200000-ffffe200003fffff] PMD ->ffff810001600000 on node 0
[ffffe20000400000-ffffe200005fffff] PMD ->ffff810001800000 on node 0
[ffffe20000600000-ffffe200007fffff] PMD ->ffff810001a00000 on node 0
[ffffe20000800000-ffffe200009fffff] PMD ->ffff810001c00000 on node 0
...
which is the ideal layout.
and usemap will share a page because of they are allocated continuously too:
sparse_early_usemap_alloc: usemap = ffff810024e00000 size = 24
sparse_early_usemap_alloc: usemap = ffff810024e00080 size = 24
sparse_early_usemap_alloc: usemap = ffff810024e00100 size = 24
sparse_early_usemap_alloc: usemap = ffff810024e00180 size = 24
...
so we make the bootmem allocation more compact and use less memory
for usemap => mission accomplished ;-)
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-generic-bitops-v3:
x86, bitops: select the generic bitmap search functions
x86: include/asm-x86/pgalloc.h/bitops.h: checkpatch cleanups - formatting only
x86: finalize bitops unification
x86, UML: remove x86-specific implementations of find_first_bit
x86: optimize find_first_bit for small bitmaps
x86: switch 64-bit to generic find_first_bit
x86: generic versions of find_first_(zero_)bit, convert i386
bitops: use __fls for fls64 on 64-bit archs
generic: implement __fls on all 64-bit archs
generic: introduce a generic __fls implementation
x86: merge the simple bitops and move them to bitops.h
x86, generic: optimize find_next_(zero_)bit for small constant-size bitmaps
x86, uml: fix uml with generic find_next_bit for x86
x86: change x86 to use generic find_next_bit
uml: Kconfig cleanup
uml: fix build error
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86-bigbox-bootparam:
x86, boot: Document for linked list of struct setup_data
x86, boot: export linked list of struct setup_data via debugfs
x86, boot: add linked list of struct setup_data
x86, boot: add free_early to early reservation machanism
* Export ide_dma_exec_cmd() and __ide_dma_test_irq().
* Constify struct ide_dma_ops.
* Always set hwif->dma_ops to &sff_dma_ops in ide_setup_dma()
(it is later overriden by ide_init_port() if needed) and drop
'const struct ide_port_info *d' argument.
While at it:
* Rename __ide_dma_test_irq() to ide_dma_test_irq().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add struct ide_dma_ops and convert core code + drivers to use it.
While at it:
* Drop "ide_" prefix from ->ide_dma_end and ->ide_dma_test_irq methods.
* Drop "ide_" "infixes" from DMA methods.
* au1xxx-ide.c:
- use auide_dma_{test_irq,end}() directly in auide_dma_timeout()
* pdc202xx_old.c:
- drop "old_" "infixes" from DMA methods
* siimage.c:
- add siimage_dma_test_irq() helper
- print SATA warning in siimage_init_one()
* Remove no longer needed ->init_hwif implementations.
v2:
* Changes based on review from Sergei:
- s/siimage_ide_dma_test_irq/siimage_dma_test_irq/
- s/drive->hwif/hwif/ in idefloppy_pc_intr().
- fix patch description w.r.t. au1xxx-ide changes
- fix au1xxx-ide build
- fix naming for cmd64*_dma_ops
- drop "ide_" and "old_" infixes
- s/hpt3xxx_dma_ops/hpt37x_dma_ops/
- s/hpt370x_dma_ops/hpt370_dma_ops/
- use correct DMA ops for HPT302/N, HPT371/N and HPT374
- s/it821x_smart_dma_ops/it821x_pass_through_dma_ops/
v3:
* Two bugs slipped in v2 (noticed by Sergei):
- use correct DMA ops for HPT374 (for real this time)
- handle HPT370/HPT370A properly
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_HFLAG_SERIALIZE_DMA host flag to serialize ports
if DMA is available and handle it in ide_init_port().
* Convert sl82c105 host driver to use this new flag.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Make sl82c105_bridge_revision() return 'u8' instead of 'unsigned long'.
* Check bridge revision in sl82c105_init_one().
While at:
* Use proper KERN_ level for printk().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Pass 'ide_hwif_t *hwif' instead of '_auide_hwif *auide' to
auide_ddma_init().
* Add 'const struct ide_port_info *d' argument to auide_ddma_init().
* Convert the driver to use ->init_dma method.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move DMA setup to palm_bk3710_init_dma().
* Convert the driver to use ->init_dma method.
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move dma_base check from sgiioc4_ide_setup_pci_device()
to ide_dma_sgiioc4().
* Replace ide_dma_sgiioc4() 'unsigned long dma_base' argument
by 'const struct ide_port_info *d'.
* Move hwif->INB setup from ide_init_sgiioc4() to
sgiioc4_ide_setup_pci_device().
* Move ide_init_sgiioc4() call from sgiioc4_ide_setup_pci_device()
to ide_dma_sgiioc4().
* Convert the driver to use ->init_dma method.
Cc: Jeremy Higdon <jeremy@sgi.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'const struct ide_port_info *d' argument to icside_dma_init().
* Make icside_dma_init() return an error value and add icside_dma_off_init()
(->init_dma implementation for case when DMA cannot be enabled).
* Convert the driver to use ->init_dma method.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move pmif->dma_regs check from pmac_ide_setup_device() to
pmac_ide_init_dma().
* Get 'pmif' from 'hwif->hwif_data' in pmac_ide_init_dma() and replace
'pmac_ide_hwif_t *pmif' argument by 'const struct ide_port_info *d'.
* Add pmac_ide_init_dma() implementation for CONFIG_BLK_DEV_IDEDMA_PMAC=n
case and convert the driver to use ->init_dma method.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Make ide_hwif_setup_dma() return an error value.
* Pass 'const struct ide_port_info *d' instead of 'unsigned long dmabase'
to ->init_dma method and make it return an error value.
* Rename ide_get_or_set_dma_base() to ide_pci_dma_base(),
change ordering of its arguments and then export it.
* Export ide_pci_set_master().
* Do complete DMA setup inside ->init_dma method and update ->init_dma
users accordingly.
* Sanitize code for DMA setup in ide_init_port().
v2:
* Fix for CONFIG_BLK_DEV_IDEDMA_PCI=n configs
(from Jiri Slaby <jirislaby@gmail.com>):
Fix following compiler warning by returning EINVAL:
In file included from ANYTHING-INCLUDING-IDE.H:45:
include/linux/ide.h: In function ‘ide_hwif_setup_dma’:
include/linux/ide.h:1022: warning: no return statement in function returning non-void
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Always use "fast" MWDMA support and remove dma_{black,white}_list
(they were based on completely bogus ->ide_dma_check implementation
which didn't set neither the host controller timings nor the device
for the desired transfer mode).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* There is no need to call ide_release_dma_engine().
* Move the code up to (and including) ide_allocate_dma_engine()
call to the callers of ide_setup_dma().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Factor out setting PCI bus-mastering from ide_hwif_setup_dma()
to ide_pci_set_master() helper.
While at it:
* don't read PCI Command register if not necessary
* use PCI device name instead of hwif->name
* cleanup ide_hwif_setup_dma() a bit
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Export ide_allocate_dma_engine() and use it in trm290 host driver.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Skip DMA initialization completely on revs < 0x20 by setting IDE_HFLAG_NO_DMA
host flag and resetting DMA host masks in alim15x3_init_one() (currently
ide_hwif_setup_dma() will try to obtain DMA base and setup PCI bus-mastering
but init_dma_ali15x3() will fail).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Do PDC202xx specific DMA initialization in init_chipset_pdc202xx()
and remove no longer needed init_dma_pdc202xx().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Nowadays BIOS info is not very useful and only confuses users since:
- IDE always tries to use DMA
- BIOS info may not be accurate with modular IDE/libata
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use hwif->name instead of cds->name in ide_allocate_dma_engine().
* Use pci_name(dev) instead of cds->name in init_dma_pdc202xx().
* Remove no longer needed ->cds field from ide_hwif_t.
v2:
* scc_pata.c also needs to be updated now (noticed by Stephen Rothwell).
There should be no functional changes caused by this patch.
Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Cc: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide_mapped_mmio_dma() and ide_iomio_dma() are called only by
ide_dma_iobase() so inline them there.
* ide_dma_iobase() is called only by ide_setup_dma() so inline
it there.
* Setup hwif->extra_base also if hwif->mmio flag is set.
There should be no functional changes casued by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Always setup hwif->extra_base in ide_iomio_dma() and remove
no longer needed ->extra field from struct ide_port_info.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
__FUNCTION__ is gcc-specific, use __func__
[bart: fix checkpatch.pl errors in ide-lib.c and ppc/mpc8xx.c while at it]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This function was simply a wrapper for a test_bit() macro so remove it and
use the macro instead.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It is no longer needed to set hwif->mmio flag to tell IDE layer to not
manage resources so cleanup host drivers that used hwif->mmio flag only
for this purpose.
Ditto for ide_legacy_init_one().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Reserve PCI BARs 0-3 (0-1 for single port controllers) in
ide_pci_enable() and remove ide_hwif_request_regions() call
from ide_device_add_all() (also cleanup resource management
in scc_pata host driver).
* Fix handling of PCI BAR 4 in ide_pci_enable(), then cleanup
ide_iomio_dma() (+ init_hwif_trm290() in trm290 host driver)
and remove ide_release[_iomio]_dma().
v2:
* Fixup trm290 host driver.
v3:
* Because of scc_pata host driver changes we need to call
pci_request_selected_regions() also in setup_mmio_scc().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Tell IDE layer to not manage resources by setting hwif->mmio flag.
* Use {request,release}_region() for resources management.
* Use driver name for resources management.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Tell IDE layer to not manage resources by setting hwif->mmio flag.
* Use {request,release}_region() for resources management.
* Set ->name field of 'struct ide_port_info' instances in legacy VLB
host drivers and use driver name for resources management.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move the common code for primary/seconary port setup from
ide_legacy_device_add() to ide_legacy_init_one().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
