We do not need to busy wait during mpi_init_check() since it is not being
invoked in atomic context. mpi_init_check() is being called from
pm8001_pci_resume(), pm8001_pci_probe(). Hence we are replacing udelay with
msleep.
Link: https://lore.kernel.org/r/20210109123849.17098-2-Viswas.G@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: akshatzen <akshatzen@google.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to the spec (JESD220E chapter 7.2), while powering off/on the ufs
device, RST_n signal should be between VSS(Ground) and VCCQ/VCCQ2.
Link: https://lore.kernel.org/r/1610103385-45755-3-git-send-email-ziqichen@codeaurora.org
Acked-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Ziqi Chen <ziqichen@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to the spec (JESD220E chapter 7.2), while powering off/on the ufs
device, REF_CLK signal should be between VSS(Ground) and VCCQ/VCCQ2.
Link: https://lore.kernel.org/r/1610103385-45755-2-git-send-email-ziqichen@codeaurora.org
Reviewed-by: Can Guo <cang@codeaurora.org>
Acked-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Ziqi Chen <ziqichen@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The variable 'status' is being initialized with SCI_SUCCESS and never
updated later with a new value. The initialization is redundant and can be
removed.
Link: https://lore.kernel.org/r/1609311860-102820-1-git-send-email-abaci-bugfix@linux.alibaba.com
Reported-by: Abaci <abaci@linux.alibaba.com>
Signed-off-by: YANG LI <abaci-bugfix@linux.alibaba.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
People testing have a need to know how many errors might be occurring over
time. Add error counters and expose them via debugfs.
A module initcall is used to create a debugfs root directory for
ufshcd-related items. In the case that modules are built-in, then
initialization is done in link order, so move ufshcd-core to the top of the
Makefile.
Link: https://lore.kernel.org/r/20210107072538.21782-1-adrian.hunter@intel.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Check that the packet is of the expected size at least, don't copy data
past the packet.
Link: https://lore.kernel.org/r/20201217203321.4539-4-parri.andrea@gmail.com
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Reported-by: Saruhan Karademir <skarade@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
vmscsi_size_delta can be written concurrently by multiple instances of
storvsc_probe(), corresponding to multiple synthetic IDE/SCSI devices;
cf. storvsc_drv's probe_type == PROBE_PREFER_ASYNCHRONOUS. Change the
global variable vmscsi_size_delta to per-synthetic-IDE/SCSI-device.
Link: https://lore.kernel.org/r/20201217203321.4539-3-parri.andrea@gmail.com
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Suggested-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current code overestimates the value of max_outstanding_req_per_channel for
Win8 and newer hosts, since vmscsi_size_delta is set to the initial value
of sizeof(vmscsi_win8_extension) rather than zero. This may lead to wrong
decisions when using ring_avail_percent_lowater equals to zero. The
estimate of max_outstanding_req_per_channel is 'exact' for Win7 and older
hosts. A better choice, keeping the algorithm for the estimation simple,
is to err the other way around, i.e., to underestimate for Win7 and older
but to use the exact value for Win8 and newer.
Link: https://lore.kernel.org/r/20201217203321.4539-2-parri.andrea@gmail.com
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Suggested-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.8.0.7
Link: https://lore.kernel.org/r/20210104180240.46824-16-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While testing recent discovery node rework, several items were seen that
could be done better with respect to the new trace event logic.
1) in the following msg:
kernel: lpfc 0000:44:00.0: start 35 end 35 cnt 0
If cnt is zero in the 1st message, there is no reason to display the
1st message, which is just giving start/end positioning.
Fix by not displaying message if cnt is 0.
2) If the driver is loaded with module log verbosity off, and later a
single NPIV host instance verbosity is enabled via sysfs, it enables
messages on all instances. This is due to the trace log verbosity checks
(lpfc_dmp_dbg) looking at the phba only. It should look at the phba and
the vport.
Fix by enabling a check on both phba and vport.
3) in the following messages:
2904 Firmware Dump Image Present on Adapter
2887 Reset Needed: Attempting Port Recovery...
These messages are not necessary for the trace event log, which is
primarily for discovery.
Fix by changing log level on these 2 messages to LOG_SLI.
Link: https://lore.kernel.org/r/20210104180240.46824-15-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Several errors have occurred where the adapter stops or fails but does not
raise the register values for the driver to detect failure. Thus driver is
unaware of the failure. The failure typically results in I/O timeouts, the
I/O timeout handler failing (after several seconds), and the error handler
escalating recovery policy and resulting in more errors. Eventually, the
driver is in a position where things have spiraled and it can't do recovery
because other recovery ops are still outstanding and it becomes unusable.
Resolve the situation by having the I/O timeout handler (actually a els,
SCSI I/O, NVMe ls, or NVMe I/O timeout), in addition to aborting the I/O,
perform a mailbox command and look for a response from the hardware. If
the mailbox command fails, it will mark the adapter offline and then invoke
the adapter reset handler to clean up.
The new I/O timeout test will be limited to a test every 5s. If there are
multiple I/O timeouts concurrently, only the 1st I/O timeout will generate
the mailbox command. Further testing will only occur once a timeout occurs
after a 5s delay from the last mailbox command has expired.
Link: https://lore.kernel.org/r/20210104180240.46824-14-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When lpfc is running in NVMET mode and supports the NVME-1 addendum
changes, a LIP on a bound NVME Initiator or lipping the lpfc NVMET's link
resulted in an Oops in lpfc_nvmet_host_release.
The fix requires lpfc NVMET to maintain an additional reference on any node
structure that acts as the hosthandle for the NVMET transport. This
reference get is a one-time addition, is taken prior to the upcall of an
unsolicited LS_REQ, and is released when the NVMET transport releases the
hosthandle during the host_release downcall.
Link: https://lore.kernel.org/r/20210104180240.46824-13-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When with testing with large numbers of npiv vports and link bounces, the
driver is flooding the messages file, even with log_verbose = 0.
The new LOG_TRACE_EVENT messages are still generating events to the
messages files.
Fix by converting the vport create msg from LOG_TRACE_EVENT to LOG_VPORT.
Link: https://lore.kernel.org/r/20210104180240.46824-12-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a mailbox command times out, the SLI port is deemed in error and the
port is reset. The HBA cleanup is not returning I/Os to the NVMe layer
before the port is unregistered. This is due to the HBA being marked
offline (!SLI_ACTIVE) and cleanup being done by the mailbox timeout handler
rather than an general adapter reset routine. The mailbox timeout handler
mailbox handler only cleaned up SCSI I/Os.
Fix by reworking the mailbox handler to:
- After handling the mailbox error, detect the board is already in
failure (may be due to another error), and leave cleanup to the
other handler.
- If the mailbox command timeout is initial detector of the port error,
continue with the board cleanup and marking the adapter offline
(!SLI_ACTIVE). Remove the SCSI-only I/O cleanup routine. The generic
reset adapter routine that is subsequently invoked, will clean up the
I/Os.
- Have the reset adapter routine flush all NVMe and SCSI I/Os if the
adapter has been marked failed (!SLI_ACTIVE).
- Rework the NVMe I/O terminate routine to take a status code to fail the
I/O with and update so that cleaned up I/O calls the wqe completion
routine. Currently it is bypassing the wqe cleanup and calling the NVMe
I/O completion directly. The wqe completion routine will take care of
data structure and node cleanup then call the NVMe I/O completion
handler.
Link: https://lore.kernel.org/r/20210104180240.46824-11-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Target reset is failed by the target as an invalid command.
The Target Reset TMF has been obsoleted in T10 for a while, but continues
to be used. On (newer) devices, the TMF is rejected causing the reset
handler to escalate to adapter resets.
Fix by having Target Reset TMF rejections be translated into a LOGO and
re-PLOGI with the target device. This provides the same semantic action
(although, if the device also supports nvme traffic, it will terminate nvme
traffic as well - but it's still recoverable).
Link: https://lore.kernel.org/r/20210104180240.46824-10-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A successful task mgmt command is logging errors, making it look like
problems were encountered. This is due to log messages for the
device/target and bus reset handlers having the LOG_TRACE_EVENT flag set.
Fix by adjusting the event flag such that the call to the logging routine
only receives a LOG_TRACE_EVENT if a prior call actually failed.
Link: https://lore.kernel.org/r/20210104180240.46824-9-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the lpfc offline routine, called for various reasons such as sysfs
attribute, driver unload, or port error, the driver is calling
__lpfc_cpuhp_remove() to destroy the hot plug data. If the offline routine
is called while the driver is in the process of being unloaded, a request
using lpfc_cpuhp_remove() is also made from lpfc_sli4_hba_unset(). The
cpuhp elements are no longer valid when the second removal request is made.
Fix by only calling the cpuhp removal once when the adapter is in the
process of unloading.
Link: https://lore.kernel.org/r/20210104180240.46824-8-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the port is configured for NVME and has any outstanding IOs when a FW
reset is requesteed, outstanding I/Os are not properly cleaned up. This
causes the fw download request to fail.
Fix by clearing the LPFC_SLI_ACTIVE flag to signify the I/O must be
manually flushed by the driver on port reset.
Link: https://lore.kernel.org/r/20210104180240.46824-7-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When lpfc generates a GEN_REQUEST wqe for the nvme LS (such as Create
Association), the timeout is set to R_A_TOV without regard to the timeout
value supplied by the nvme-fc transport. The driver should be setting the
timeout to the value passed into the routine. Additionally the caller
should be setting the timeout value to the value in the ls request set by
the nvme transport. Instead, it unconditionally is setting it to a driver
defined value. So the driver actually overrode the value twice.
Fix by using the timeout provided to the routine, and for the caller, set
the timeout to the ls request timeout value.
Link: https://lore.kernel.org/r/20210104180240.46824-6-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver's management of the fabric controller (aka pseudo-scsi
initiator) node in SLI3 mode is causing this crash. The crash occurs
because of a node reference imbalance that frees the fabric controller node
while devloss is outstanding from the SCSI transport. This is triggered by
an odd behavior where the switch reacts to a rejected RDP request with a
PLOGI and nothing else, not even a LOGO. The driver ACKS the PLOGI and
after successfully registering the RPI, incorrectly registers the fabric
controller node because it has the NLP_FC4_FCP flag still set from the
fabric controller PRLI. If a LIP is issued, the driver attempts to cleanup
on Link Up and ends up executing too many puts.
Fix by detecting the fabric node type and clearing out the nodes internal
flags that triggered a SCSI transport registration and subsequence dev_loss
event. The driver cannot count on any persistence from fabric controller
nodes.
Link: https://lore.kernel.org/r/20210104180240.46824-5-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Testing with target ports coming and going, the driver eventually reached a
state where it no longer discovered the target. When the driver has issued
a PRLI and receives a PRLI from the target, it is not properly updating the
node's initiator/target role flags. Thus, when a subsequent RSCN is
received for a target loss, the driver mis-identifies the target as an
initiator and does not initiate LUN scanning.
Fix by always refreshing the ndlp with the latest PRLI state information
whenever a PRLI is processed. Also clear the ndlp flags when processing a
PLOGI so that there is no carry over through a re-login.
Link: https://lore.kernel.org/r/20210104180240.46824-4-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A very long time ago, there was a feature: auto sli mode. It gave the user
the ability to auto select the SLI mode (SLI2 or SLI3) to run the port in,
or even force SLI2 mode if configured. Because of the convoluted logic,
the CONFIG_PORT mbox command ends up being called 2 or 3 times. It should
have been called only once. Additionally, the driver no longer supports
SLI-2, so only SLI-3 mode should be allowed.
The following changes were made:
- Force module parameter to SLI3 only.
- Rip out redundant CONFIG_PORT mbox commands.
- Force CONFIG_PORT mbox command to be in beginning of enable ISR routine.
- Added changes for offline to online behavior
Link: https://lore.kernel.org/r/20210104180240.46824-3-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Under some pt2pt situations, the other end of the link may issue a LOGO
after successfully completing PLOGI and assigning addresses to the port.
Thus the driver may attempt a new PLOGI to re-create the login, but the
LOGO handling cleared the address back to 0. Once this happens, the other
end, which may be address 0, gets all confused and this cannot be resolved
without an administrative action to bounce the link.
Fix by assuming that address assignment only occurs on the 1st PLOGI after
link up, and regardless of login state, the address assignment sticks. The
FC standards aren't particularly clear in this situation (it only describes
initial PLOGI), but there is nothing that contradicts this and behaviors on
the devices tested appears to conform to the understanding.
Thus, don't reset the port address to 0 as part of LOGO handling. Port
addresses will only reset on link down.
Link: https://lore.kernel.org/r/20210104180240.46824-2-jsmart2021@gmail.com
Co-developed-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
sprintf and snprintf may cause output defect in sysfs content, it is better
to use new added sysfs_emit function which knows the size of the temporary
buffer.
Link: https://lore.kernel.org/r/20210106211541.23039-1-huobean@gmail.com
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use consistent and expected indentation for all Kconfig text.
Link: https://lore.kernel.org/r/20210106205554.18082-1-rdunlap@infradead.org
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: linux-scsi@vger.kernel.org
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver's queuecommand routine is still wrapped to hold the host lock
for the duration of the call. This will become problematic when moving to
multiple queues due to the lock contention preventing asynchronous
submissions to mulitple queues. There is no real legitimate reason to hold
the host lock, and previous patches have insured proper protection of
moving ibmvfc_event objects between free and sent lists.
Link: https://lore.kernel.org/r/20210106201835.1053593-6-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Drain the command queue and place all commands on a completion list.
Perform command completion on that list outside the host/queue locks.
Further, move purged command compeletions outside the host_lock as well.
Link: https://lore.kernel.org/r/20210106201835.1053593-5-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Define per-queue locks for protecting queue state and event pool sent/free
lists. The evt list lock is initially redundant but it allows the driver to
be modified in the follow-up patches to relax the queue locking around
submissions and completions.
Link: https://lore.kernel.org/r/20210106201835.1053593-4-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is currently a single command event pool per host. In anticipation of
providing multiple queues add a per-queue event pool definition and
reimplement the existing CRQ to use its queue defined event pool for
command submission and completion.
Link: https://lore.kernel.org/r/20210106201835.1053593-3-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The primary and async CRQs are nearly identical outside of the format and
length of each message entry in the dma mapped page that represents the
queue data. These queues can be represented with a generic queue structure
that uses a union to differentiate between message format of the mapped
page.
This structure will further be leveraged in a followup patcheset that
introduces Sub-CRQs.
Link: https://lore.kernel.org/r/20210106201835.1053593-2-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Transaction Specific Fields (TSF) in the UPIU package could be CDB
(SCSI/UFS Command Descriptor Block), OSF (Opcode Specific Field), and TM
I/O parameter (Task Management Input/Output Parameter). But, currently, we
take all of these as CDB in the UPIU trace. Thus makes user confuse among
CDB, OSF, and TM message. So fix it with this patch.
Link: https://lore.kernel.org/r/20210105113446.16027-7-huobean@gmail.com
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Distinguish between TM request UPIU and response UPIU in TM UPIU trace, for
the TM response, let TM UPIU trace print its TM response UPIU.
Link: https://lore.kernel.org/r/20210105113446.16027-6-huobean@gmail.com
Acked-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, in the query completion trace print, since we use
hba->lrb[tag].ucd_req_ptr and didn't differentiate UPIU between request and
response, thus header and transaction-specific field in UPIU printed by
query trace are identical. This is not very practical. As below:
query_send: HDR:16 00 00 0e 00 81 00 00 00 00 00 00, CDB:06 0e 03 00 00 00 00 00 00 00 00 00 00 00 00 00
query_complete: HDR:16 00 00 0e 00 81 00 00 00 00 00 00, CDB:06 0e 03 00 00 00 00 00 00 00 00 00 00 00 00 00
For the failure analysis, we want to understand the real response reported
by the UFS device, however, the current query trace tells us nothing. After
this patch, the query trace on the query_send, and the above a pair of
query_send and query_complete will be:
query_send: HDR:16 00 00 0e 00 81 00 00 00 00 00 00, CDB:06 0e 03 00 00 00 00 00 00 00 00 00 00 00 00 00
ufshcd_upiu: HDR:36 00 00 0e 00 81 00 00 00 00 00 00, CDB:06 0e 03 00 00 00 00 00 00 00 00 01 00 00 00 00
Link: https://lore.kernel.org/r/20210105113446.16027-5-huobean@gmail.com
Acked-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don't call trace_ufshcd_upiu() in case ufshba_upiu trace poit is not
enabled.
Link: https://lore.kernel.org/r/20210105113446.16027-4-huobean@gmail.com
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
__print_symbolic() is designed for exporting the print formatting table to
userspace and allows parsing tool, such as trace-cmd and perf, to analyze
trace log according to this print formatting table, meanwhile, by using
__print_symbolic()s, save space in the trace ring buffer.
original print format:
print fmt: "%s: %s: HDR:%s, CDB:%s", __get_str(str), __get_str(dev_name),
__print_hex(REC->hdr, sizeof(REC->hdr)),
__print_hex(REC->tsf, sizeof(REC->tsf))
after this change:
print fmt: "%s: %s: HDR:%s, CDB:%s",
print_symbolic(REC->str_t, {0, "send"},
{1, "complete"},
{2, "dev_complete"},
{3, "query_send"},
{4, "query_complete"},
{5, "query_complete_err"},
{6, "tm_send"},
{7, "tm_complete"},
{8, "tm_complete_err"}),
__get_str(dev_name), __print_hex(REC->hdr, sizeof(REC->hdr)),
__print_hex(REC->tsf, sizeof(REC->tsf))
Note: This patch just converts current __get_str(str) to __print_symbolic(),
the original tracing log will not be affected by this change, so it
doesn't break what current parsers expect.
Link: https://lore.kernel.org/r/20210105113446.16027-3-huobean@gmail.com
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current EM macro definition, we use stringize operator '#', which turns the
argument it precedes into a quoted string. Thus requires the symbol of
__print_symbolic() should be the string corresponding to the name of the
enum.
However, we have other cases, the symbol and enum name are not the same, we
can redefine EM/EMe, but there will introduce some redundant codes. This
patch is to remove this restriction, let others reuse the current EM/EMe
definition.
Link: https://lore.kernel.org/r/20210105113446.16027-2-huobean@gmail.com
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 996e509bbc ("sd: use __register_blkdev to avoid a modprobe for an
unregistered dev_t") removed blk_register_region(devt, ...) in sd_remove()
and since then, devt is unused in sd_remove().
Hence, make W=1 warns:
drivers/scsi/sd.c:3516:8:
warning: variable 'devt' set but not used [-Wunused-but-set-variable]
Simply remove this obsolete variable.
[mkp: fixed commit sha]
Link: https://lore.kernel.org/r/20201214095424.12479-1-lukas.bulwahn@gmail.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The block layer code will split a large zeroout request into multiple bios
and if WRITE SAME is disabled because the storage device reports that it
does not support it (or support the length used), we can get an error
message from the block layer despite the setting of RQF_QUIET on the first
request. This is because more than one request may have already been
submitted.
Fix this by setting RQF_QUIET when BLK_STS_TARGET is returned to fail the
request early, we don't need to log a message because we did not actually
submit the command to the device, and the block layer code will handle the
error by submitting individual write bios.
Link: https://lore.kernel.org/r/20201207221021.28243-1-emilne@redhat.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When sdeb_zbc_model does not match BLK_ZONED_NONE, BLK_ZONED_HA or
BLK_ZONED_HM, we should free sdebug_q_arr to prevent memleak. Also there is
no need to execute sdebug_erase_store() on failure of sdeb_zbc_model_str().
Link: https://lore.kernel.org/r/20201226061503.20050-1-dinghao.liu@zju.edu.cn
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The CHAP secret displayed garbage characters causing iSCSI login
authentication failure. Correct the CHAP password max length.
Link: https://lore.kernel.org/r/20201217105144.8055-1-njavali@marvell.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Users can initiate resets to specific SCSI device/target/host through
IOCTL. When this happens, the SCSI cmd passed to eh_device/target/host
_reset_handler() callbacks is initialized with a request whose tag is -1.
In this case it is not right for eh_device_reset_handler() callback to
count on the LUN get from hba->lrb[-1]. Fix it by getting LUN from the SCSI
device associated with the SCSI cmd.
Link: https://lore.kernel.org/r/1609157080-26283-1-git-send-email-cang@codeaurora.org
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The UniPro specification states that attribute IDs of the following
parameters are vendor-specific so some SoCs could have no regions at the
defined addresses:
- DME_LocalFC0ProtectionTimeOutVal
- DME_LocalTC0ReplayTimeOutVal
- DME_LocalAFC0ReqTimeOutVal
In addition, the following parameters should be set considering the
compatibility between host and device.
- PA_PWRMODEUSERDATA0
- PA_PWRMODEUSERDATA1
- PA_PWRMODEUSERDATA2
- PA_PWRMODEUSERDATA3
- PA_PWRMODEUSERDATA4
- PA_PWRMODEUSERDATA5
Introduce a quirk to allow vendor drivers to override the UniPro defaults.
Link: https://lore.kernel.org/r/1fedd3dea0ccc980913a5995a10510d86a5b01b9.1608513782.git.kwmad.kim@samsung.com
Acked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current flush location does not guarantee disabling BKOPS for the case
of requesting device power off.
1) The exceptional event handler is queued
2) ufs suspend starts with a request of device power off
3) BKOPS is disabled in ufs suspend
4) The queued work for the handler is done and BKOPS is re-enabled
Relocate the flush statement to ensure BKOPS remain disabled.
Link: https://lore.kernel.org/r/1608360039-16390-1-git-send-email-kwmad.kim@samsung.com
Reviewed-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Flush during hibern8 is sufficient on MediaTek platforms, thus enable
UFSHCI_QUIRK_SKIP_MANUAL_WB_FLUSH_CTRL to skip enabling
fWriteBoosterBufferFlush during WriteBooster initialization.
Link: https://lore.kernel.org/r/20201222072928.32328-1-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
UFSHCI_QUIRK_SKIP_MANUAL_WB_FLUSH_CTRL is intended to skip enabling
fWriteBoosterBufferFlushEn while WriteBooster is initializing. Therefore
it is better to apply the checking during WriteBooster initialization only.
Link: https://lore.kernel.org/r/20201222072905.32221-3-stanley.chu@mediatek.com
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently if device needs to do flush or BKOP operations, the device VCC
power is kept during runtime-suspend period.
However, if system suspend is happening while device is runtime-suspended,
such power may not be disabled successfully.
The reasons may be,
1. If current PM level is the same as SPM level, device will keep
runtime-suspended by ufshcd_system_suspend().
2. Flush recheck work may not be scheduled successfully during system
suspend period. If it can wake up the system, this is also not the
intention of the recheck work.
To fix this issue, simply runtime-resume the device if the flush is allowed
during runtime suspend period. Flush capability will be disabled while
leaving runtime suspend, and also not be allowed in system suspend period.
Link: https://lore.kernel.org/r/20201222072905.32221-2-stanley.chu@mediatek.com
Fixes: 51dd905bd2 ("scsi: ufs: Fix WriteBooster flush during runtime suspend")
Reviewed-by: Chaotian Jing <chaotian.jing@mediatek.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Merge two commits that had dependencies on other 5.11 trees (the block
and the irq trees respectively).
- We reverted a megaraid_sas change in 5.10 due to missing block
layer plumbing. Now that this is in place, reinstate the change.
- The hisi_sas driver had a dependency on a driver core irq change
that went in through Thomas' tree.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
