The Encoder will only allow the Raw VBI parameters, along with a number of
other API parameters, to take effect when no analog captures are in
progress. These parameters must be set before the first analog capture starts,
be it MPEG, VBI, YUV, etc., and cannot be changed until the last one stops. It
is not obvious to me what capture channel API parameters are shared and which
ones must be set per capture channel, so set them all for every analog
capture channel start up. This fixes the driver so that VBI capture can be
started up after the MPEG capture is going.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
More sliced VBI fixes to bring the cx18 driver closer to full V4L2 spec
compliance for VBI and to get sliced VBI working better.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The old code from ivtv used a CX23415/6 PTS, which was simply left at 0 in the
cx18 driver. Since the CX23418 gives us what I think is a PTS (or some other
90 kHz clock count) with each VBI buffer, this change has the cx18 driver use
that as a PTS.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The CX18_AUDIO_ENABLE register usually never reads back what was just written
under normal circumstances. Perform better checking that a write went to the
register as expected with a specification of what bits to verify.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch also enables the autogain for the mt9v111.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The mi1310_soc sequences come from the ms-win driver C0130Dev.inf.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I2C_DRIVERIDs are phased out. Remove those that are unused at the moment.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A hue of -128 was rejected due to an incorrect range check, which was
faithfully copy-and-pasted into four drivers...
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Most boards nowadays supports saa7134-alsa. Even some of they doesn't have any
option to wire an audio cable. So, lets load saa7134-alsa by default, if the
board is not based on saa7130 and if saa7134-alsa is compiled.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
saa7134: Fix tuner access on Kworld ATSC110
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The lack of the green color is fixed by sensor sequences closer to the
ms-win traces.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The webcams worked only one time after connection.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the wrong clock value, the image had two moving colored lines.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bugs were in the first init sequence of the sensor.
The rewrite is adapted from a ms-win trace.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for USB webcams based on the MR97310A chip. It was
tested with an Aiptek PenCam VGA+ webcam.
Signed-off-by: Kyle Guinn <elyk03@gmail.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The returned value of i2c read is a 16 bits word. It was stored in
a 8 bits variable, preventing a sensor to be detected.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Hercules webcam based on ov534 use different sensor than Playstation Eye,
disable them until full support is provided.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This webcam is generic and some sensors are not treated by
the driver zc0301.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The err, warning and info redefinitions don't need the use of
do {} while.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Introduce int ret and check it value after call to usb_register().
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The transfer endpoint address is now automatically chosen.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Just call em28xx_isoc_audio_deinit() if em28xx sent a usb_submit().
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added entry for GADMEI TVR200.
Thanks to Yohanes Nugroho <yohanes@gmail.com> for testing and data collection.
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_make_path reports canonical bus info. Use it when reporting bus info
in VIDIOC_QUERYCAP.
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_make_path reports canonical bus info. Use it when reporting bus info
in VIDIOC_QUERYCAP.
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Acked-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_make_path reports canonical bus info. Use it when reporting bus info
in VIDIOC_QUERYCAP.
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_make_path reports canonical bus info. Use it when reporting bus info
in VIDIOC_QUERYCAP.
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes a free-without-alloc bug for V4L2_MEMORY_USERPTR
video buffers.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It's a quad Bt878 PCI-e x1 capture board that's basically the same as the
IVC-200 (quad Bt878 PCI) capture board that's currently supported in
the V4L2 bttv driver.
Manufacturer's web page for IVCE-8784 with photo and info:
http://www.iei.com.tw/en/product_IPC.asp?model=IVCE-8784
Signed-off-by: Douglas Kosovic <douglask@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch removes err() macros from few usb devices.
It places pr_err in pvrusb2-v4l2.c, dev_err in dabusb and in usbvision
drivers. Beside placing dev_err, patch defines new s2255_dev_err macro
with S2255_DRIVER_NAME in s2255 module.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Acked-by: Thierry Merle <thierry.merle@free.fr>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The dynamically allocated input_dev->phys buffer isn't freed when
unregistering the device. As the input layer doesn't provide any release
callback, use a fixed-size buffer inside the uvc_device structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
URB buffers for video transfers are sized to UVC_MAX_PACKETS bulk/isochronous
packets by default. If the system is too low on memory try successively
smaller numbers of packets until allocation succeeds.
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Alcor Micro AU3820 chipset (found in the Future Boy PC USB webcam)
requires the MINMAX quirk. Add a corresponding entry in the device IDs list.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
strncpy is unsafe as it doesn't append a terminating NUL character when the
source string doesn't fit in the destination buffer. Replace it with strlcpy.
strncat is misused as its size argument refers to the source string, not the
destination buffer. Replace it with strlcat.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
request_module() needs to be called with a string literal for a
format string or with 1 or more variable arguments to avoid
compiler warnings and possible exploits, if someone could cause
us to get a format string with a '%' code in the format string
when we make the call.
Reported-by: Brandon Jenkins <bcjenkins@tvwhere.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
First step in conversion to the new V4L2 framework. Added per cx18 device
instance of the v4l2_device and its registration.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Renamed structure member name to be more specific to type in anticipation
of updating to the v4l2_device/v4l2_subdev framework. Too many objects named
"dev" and /v4l2_\{0,1\}dev/ would be to confusing.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Normalize the APU state before the second firmware load so that audio
for the first analog capture is correct.
Many thanks to Conexant for supporting me in finding a solution for this
problem.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix bugs in the cx18 AC3 control implementation that would have affected
ivtv and other drivers via the cx2341x module. Bring AC3 controls
behavior into comliance with V4L2 specification. Thanks to Hans Verkuil
for reviewing the previous patch and pointing out the problems.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Initial addition of controls to set AC-3 audio encoding for the CX23418 - it
does not work yet due to firmware or cx18 driver issues. This change affects
the common cx2341x and ivtv modules due to shared structures and
common functions.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added debug display of outgoing mailbox arguments. Fixed a minor problem
with display of stale incoming mailbox contents, when user was not looking for
debug warnings.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A redundant PLL divisior update for the I2S master clock after AV core
firmware load was missed in earlier PLL parameter changes. This one really
doesn't matter because it's redundant and gets overwritten, but the driver
should be self consistent in the values used.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The conversion to video_ioctl2 is the first phase to converting this driver
to the latest v4l2 framework.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
DVBWorld DVBS2 PCI-e 2005 card contains cx23885 PCI-e bridge
and cx24116 demodulator.
http://www.linuxtv.org/wiki/index.php/DVBWorld_DVB-S2_2005_PCI-Express_Card
The card tested by me (Igor).
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
TeVii S470 DVB-S2 PCI-e card contains cx23885 PCI-e bridge
and cx24116 demodulator.
http://www.linuxtv.org/wiki/index.php/TeVii_S470
The card tested by me (Igor).
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
TurboSight TBS6920 DVB-S2 PCI-e card contains cx23885 PCI-e bridge
and cx24116 demodulator.
http://www.linuxtv.org/wiki/index.php/TBS_6920
The card tested by me (Igor).
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The name of the pvrusb2 module is not likely to ever change, and there
are plenty of other places where the name is directly coded, so there
is little utility in using a macro to infer the module name here. In
addition, using that macro complicates other uses of the driver
involving older kernels where this macro works differently. Yes I
know for many places we don't have to worry about that. But my
alternative is that I have to build special logic in the pvrusb2
standalone driver to special-case what is otherwise costmetic and that
is just plain nuts for something as trivial as this, especially since
this change does not at all have any compile time or run time impact
on the driver. I'm just removing a nicety that didn't have a lot of
value here to begin with.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It appears that various v4l-dvb drivers are changing to require
explicit initialization before use. This change to the pvrusb2 driver
implements an automatic issuance of VIDIOC_INT_INIT when a module is
bound to the driver, thus conforming to the new behavior.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add v4l2_i2c_tuner_addrs() to obtain the various I2C tuner addresses.
This will be used in several drivers, so make this a common function
as we do not want to have these I2C addresses all over the place.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Register v4l2_device and switch to v4l2_subdev to access the i2c modules.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for Philips webcam snapshot button as an
event input device, for consistency with other webcam drivers.
Signed-off-by: Pham Thanh Nam <phamthanhnam.ptn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Previous v4l-dvb changeset id 4cc8ed11e2e0 changed the pvrusb2-hdw
internal API regarding i2c chip debug register access. However that
change failed to also update the corresponding function comment
describing the API. As driver maintained I never saw a request for an
ack on that change; there probably should have been one especially
since the manner in which this API operates was changed - its
interface is now entangled with a v4l specific struct and I would have
preferred to keep this API clear of moving-target v4l-isms such as
this one if at all possible which is why I had done it the way I did
before. But whatever. This commit at least fixes the comment issue.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the new pvrusb2 internal API to grab the device identifier, rather
than generating it directly. This unifies some code and make possible
use of that identifier in places other than sysfs.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Implement a new internal function to create a string device
identifier. This ID stays with the specific device, making it useful
to user space to identify specific devices. We use the serial number
if available; otherwise we give up and just spit out a unit/instance ID.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds the capability of selecting between 4 different inputs
on vivi driver. Input 0 is the normal color bar, while inputs 1-3 are
modified color bars.
This allows testing input selection on userspace applications and
serves as an implementation model for other drivers.
The current approach allows a maximum of 10 different inputs, since the
input name generator assumes that we need just one digit to present the
input. It shouldn't be hard to modify it to present a bigger name of
inputs, but, in fact, it doesn't make much sense of doing it for this
test driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
zl10353 i2c-gate was always closed and due to that devices having tuner
behind i2c-gate were broken. Add module configuration which allows disabling
i2c-gate only when really needed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
1. Driver code where pxa_request_dma() is called will most likely
reference DMA registers as well, and it is really unnecessary
to include pxa-regs.h just for this. Move the definitions into
<mach/dma.h> and make relevant drivers include it instead of
<mach/pxa-regs.h>.
2. Introduce DMAC_REGS_VIRT as the virtual address base for these
DMA registers. This allows later processors to re-use the same
IP while registers may start at different I/O address.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
AFAIK, the bt866 is only seen on AverMedia 6 Eyes. However, no module selects it.
Adds a proper select for this driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 'bytes' array is 64 bytes large but the easy standard programming
(TDA9874A_ESP) has a number of 255, outside the shadow array size.
This patch increases the size of the shadow array in order to accomodate
this register.
Signed-off-by: Vitaly Wool <vital@embeddedalley.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The previous probe rotine tried to read 6 bytes in one chunk which currently isn't allowed. This is the rev. 10346 243399e67c41 readded with a high priority.
Signed-off-by: Gregory Lardiere <spmf2004-m560x@yahoo.fr>
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - touchpad driver miss-recognising logitech mice
Input: synaptics - ensure we reset the device on resume
Input: usbtouchscreen - fix eGalax HID ignoring
Input: ambakmi - fix timeout handling in amba_kmi_write()
Input: pxa930_trkball - fix write timeout handling
Input: struct device - replace bus_id with dev_name(), dev_set_name()
Input: bf54x-keys - fix debounce time validation
Input: spitzkbd - mark probe function as __devinit
Input: omap-keypad - mark probe function as __devinit
Input: corgi_ts - mark probe function as __devinit
Input: corgikbd - mark probe function as __devinit
Input: uvc - the button on the camera is KEY_CAMERA
Input: psmouse - make MOUSE_PS2_LIFEBOOK depend on X86
Input: atkbd - make forced_release_keys[] static
Input: usbtouchscreen - allow reporting calibrated data
As explained in "Writing an ALSA driver" (T. Iwai), audio drivers should
set the struct device for the card before registering the card instance.
This will add the correct /sys/class/sound/cardN/device symlink, so HAL
can see the device and ConsoleKit sets its ACL permissions for the
logged-in user.
For em28xx audio capture cards found e.g. in Hauppauge WinTV-HVR-900 (R2),
this patch fixes errors like:
ALSA lib pcm_hw.c:1429:(_snd_pcm_hw_open) Invalid value for card
Error opening audio: Permission denied
when running mplayer as a normal user.
Signed-off-by: Nicola Soranzo <nsoranzo@tiscali.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new v4l2_subdev_call used s_fmt instead of g_fmt.
Thanks-to: Andy Walls <awalls@radix.net>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The video_ioctl2 conversion of ivtv in kernel 2.6.27 introduced a bug
causing decoder commands to crash. The decoder commands should have been
handled from the video_ioctl2 default handler, ensuring correct mapping
of the argument between user and kernel space. Unfortunately they ended
up before the video_ioctl2 call, causing random crashes.
Thanks to hannes@linus.priv.at for testing and helping me track down the
cause!
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If a device using the gspca framework is unplugged while it is still streaming
then the call that is used to free the URBs that have been allocated occurs
after the pointer it uses becomes invalid at the end of gspca_disconnect.
Make another cleanup call in gspca_disconnect while the pointer is still
valid (multiple calls are OK as destroy_urbs checks for pointers already
being NULL.
Signed-off-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According with saa7130 public datasheet, saa7130 doesn't support
digital audio. This is also confirmed by experimental tests. So, it
doesn't make sense to let saa7134-alsa register for those chipsets.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Resetting the streaming flag on disconnection prevented the URBs to be freed
when streaming was active.
Also, USBs cannot be killed after disconnection (oops in [usbcore] unlink1).
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Trace: (Provided by Douglas)
BUG: sleeping function called from invalid context at drivers/usb/core/urb.c:558
in_atomic():0, irqs_disabled():1
Pid: 4918, comm: sox Not tainted 2.6.27.5 #1
[<c04246d8>] __might_sleep+0xc6/0xcb
[<c058c8b0>] usb_kill_urb+0x1a/0xd8
[<c0488e68>] ? __kmalloc+0x9b/0xfc
[<c0488e85>] ? __kmalloc+0xb8/0xfc
[<c058cd5a>] ? usb_alloc_urb+0xf/0x31
[<f8dd638c>] em28xx_isoc_audio_deinit+0x2f/0x6c [em28xx_alsa]
[<f8dd6573>] em28xx_cmd+0x1aa/0x1c5 [em28xx_alsa]
[<f8dd65e1>] snd_em28xx_capture_trigger+0x53/0x68 [em28xx_alsa]
[<f8aa8674>] snd_pcm_do_start+0x1c/0x23 [snd_pcm]
[<f8aa85d7>] snd_pcm_action_single+0x25/0x4b [snd_pcm]
[<f8aa9833>] snd_pcm_action+0x6a/0x76 [snd_pcm]
[<f8aa98f5>] snd_pcm_start+0x14/0x16 [snd_pcm]
[<f8aae10e>] snd_pcm_lib_read1+0x66/0x273 [snd_pcm]
[<f8aac5a3>] ? snd_pcm_kernel_ioctl+0x46/0x5f [snd_pcm]
[<f8aae4a7>] snd_pcm_lib_read+0xbf/0xcd [snd_pcm]
[<f8aad774>] ? snd_pcm_lib_read_transfer+0x0/0xaf [snd_pcm]
[<f89feeb6>] snd_pcm_oss_read3+0x99/0xdc [snd_pcm_oss]
[<f89fef9c>] snd_pcm_oss_read2+0xa3/0xbf [snd_pcm_oss]
[<c064169d>] ? _cond_resched+0x8/0x32
[<f89ff0be>] snd_pcm_oss_read+0x106/0x150 [snd_pcm_oss]
[<f89fefb8>] ? snd_pcm_oss_read+0x0/0x150 [snd_pcm_oss]
[<c048c6e2>] vfs_read+0x81/0xdc
[<c048c7d6>] sys_read+0x3b/0x60
[<c04039bf>] sysenter_do_call+0x12/0x34
=======================
The culprit in the trace is snd_pcm_action() which invokes a spin lock
which disables pre-emption which disables an IRQ which causes the
__might_sleep() function to fail the irqs_disabled() test. Since
pre-emption is enabled then it is safe to de-allocate the memory if
you first unlink each URB. In this instance you are safe since
pre-emption is disabled. If pre-emption and irqs are not disabled then
call usb_kill_urb(), else call usb_unlink_urb().
Thanks to Douglas for tracking down this bug originally!!!
[dougsland@redhat.com: Fixed codyingstyle]
Signed-off-by: Robert Krakora <rob.krakora@messagenetsystems.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These days TUNER_SET_CONFIG is broadcast to the other i2c devices
and that triggers a fw load on the cx25840. Ignore this command
since cx25840 isn't a tuner and you really do not want to load
the firmware that early.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Revert a change made in change 9743 which resulted in a kernel panic in some
cases on shutdown of the audio stream.
First discovered when working on the Pinnacle 880e support, and later
reproduced by a user on the mailing list with the HVR-900 as well.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix for KWorld 330U Board
Many thanks to Devin and Mauro!!!
Signed-off-by: Robert Krakora <rob.krakora@messagenetsystems.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix for KWorld 330U AC97
Many thanks to Devin and Mauro again!!!
Signed-off-by: Robert Krakora <rob.krakora@messagenetsystems.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the conversion to v4l2_subdev one bit of code was accidentally dropped:
on receiving the first command the driver has to load the fw. A new init()
command was introduced to do that explicitly for bridge drivers that are
converted to use v4l2_subdev, but old drivers that are not yet converted
no longer worked.
This patch fixes this regression for these old drivers.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
