Add support for S2MPS14 PMIC device to the MFD sec-core driver.
The S2MPS14 is similar to S2MPS11 but it has fewer regulators, two
clocks instead of three and a little different registers layout.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The S2MPS11 RTC has two alarms: alarm0 and alarm1 (corresponding
interrupts are named similarly). Use consistent names for interrupts to
limit possible errors.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add maximum register to the regmap used by rtc-s5m driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If we compile the TPS65217 for a 64bit architecture we receive the following
warnings:
drivers/mfd/tps65217.c: In function ‘tps65217_probe’:
drivers/mfd/tps65217.c:173:13:
warning: cast from pointer to integer of different size
chip_id = (unsigned int)match->data;
^
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If we compile the MAX8998 for a 64bit architecture we receive the following
warnings:
drivers/mfd/max8998.c: In function ‘max8998_i2c_get_driver_data’:
drivers/mfd/max8998.c:178:10:
warning: cast from pointer to integer of different size
return (int)match->data;
^
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If we compile the MAX8997 for a 64bit architecture we receive the following
warnings:
drivers/mfd/max8997.c: In function ‘max8997_i2c_get_driver_data’:
drivers/mfd/max8997.c:173:10:
warning: cast from pointer to integer of different size
return (int)match->data;
^
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull LED subsystem update from Bryan Wu:
"Basically this cycle is mostly cleanup for LED subsystem"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: s3c24xx: Remove hardware.h inclusion
leds: replace list_for_each with list_for_each_entry
leds: kirkwood: Cleanup in header files
leds: pwm: Remove a warning on non-DT platforms
leds: leds-pwm: fix duty time overflow.
leds: leds-mc13783: Remove unneeded mc13xxx_{un}lock
leds: leds-mc13783: Remove duplicate field in platform data
drivers: leds: leds-tca6507: check CONFIG_GPIOLIB whether defined for 'gpio_base'
leds: lp5523: Support LED MUX configuration on running a pattern
leds: lp5521/5523: Fix multiple engine usage bug
LEDS: tca6507 - fix up some comments.
LEDS: tca6507: add device-tree support for GPIO configuration.
LEDS: tca6507 - fix bugs in parsing of device-tree configuration.
LED platform data are overwhelmed by excessive field "max_cur"
which just replicates few bits of "led_control" field.
This patch removes this field and adds a definition for the
current settings in the header.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Core:
- Avoid get_cd() on cards marked nonremovable.
Drivers:
- arasan: New driver for controllers found in e.g. Xilinx Zynq SoC.
- dwmmc: Support Hisilicon K3 SoC controllers.
- esdhc-imx: Support for HS200 mode, DDR modes on MX6, runtime PM.
- sdhci-pci: Support O2Micro/BayHubTech controllers used in laptops
like Lenovo ThinkPad W540, Dell Latitude E5440, Dell Latitude E6540.
- tegra: Support Tegra124 SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=wZBx
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.14:
Core:
- Avoid get_cd() on cards marked nonremovable
Drivers:
- arasan: New driver for controllers found in e.g. Xilinx Zynq SoC
- dwmmc: Support Hisilicon K3 SoC controllers
- esdhc-imx: Support for HS200 mode, DDR modes on MX6, runtime PM
- sdhci-pci: Support O2Micro/BayHubTech controllers used in laptops
like Lenovo ThinkPad W540, Dell Latitude E5440, Dell Latitude E6540
- tegra: Support Tegra124 SoCs"
* tag 'mmc-updates-for-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (55 commits)
mmc: sdhci-pci: Fix possibility of chip->fixes being null
mmc: sdhci-pci: Fix BYT sd card getting stuck in runtime suspend
mmc: sdhci: Allow for long command timeouts
mmc: sdio: add a quirk for broken SDIO_CCCR_INTx polling
mmc: sdhci: fix lockdep error in tuning routine
mmc: dw_mmc: k3: remove clk_table
mmc: dw_mmc: fix dw_mci_get_cd
mmc: dw_mmc: fix sparse non static symbol warning
mmc: sdhci-esdhc-imx: fix warning during module remove function
mmc: sdhci-esdhc-imx: fix access hardirq-unsafe lock in atomic context
mmc: core: sd: implement proper support for sd3.0 au sizes
mmc: atmel-mci: add vmmc-supply support
mmc: sdhci-pci: add broken HS200 quirk for Intel Merrifield
mmc: sdhci: add quirk for broken HS200 support
mmc: arasan: Add driver for Arasan SDHCI
mmc: dw_mmc: add dw_mmc-k3 for k3 platform
mmc: dw_mmc: use slot-gpio to handle cd pin
mmc: sdhci-pci: add support of O2Micro/BayHubTech SD hosts
mmc: sdhci-pci: break out definitions to header file
mmc: tmio: fixup compile error
...
Conflicts:
MAINTAINERS
A respin of the merges in the previous pull request with one extra fix.
A quiet release for the regulator API, quite a large number of small
improvements all over but other than the addition of new drivers for the
AS3722 and MAX14577 there is nothing of substantial non-local impact.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1NsR
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"A respin of the merges in the previous pull request with one extra
fix.
A quiet release for the regulator API, quite a large number of small
improvements all over but other than the addition of new drivers for
the AS3722 and MAX14577 there is nothing of substantial non-local
impact"
* tag 'regulator-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (47 commits)
regulator: pfuze100-regulator: Improve dev_info() message
regulator: pfuze100-regulator: Fix some checkpatch complaints
regulator: twl: Fix checkpatch issue
regulator: core: Fix checkpatch issue
regulator: anatop-regulator: Remove unneeded memset()
regulator: s5m8767: Update LDO index in s5m8767-regulator.txt
regulator: as3722: set enable time for SD0/1/6
regulator: as3722: detect SD0 low-voltage mode
regulator: tps62360: Fix up a pointer-integer size mismatch warning
regulator: anatop-regulator: Remove unneeded kstrdup()
regulator: act8865: Fix build error when !OF
regulator: act8865: register all regulators regardless of how many are used
regulator: wm831x-dcdc: Remove unneeded 'err' label
regulator: anatop-regulator: Add MODULE_ALIAS()
regulator: act8865: fix incorrect devm_kzalloc for act8865
regulator: act8865: Remove set_suspend_[en|dis]able implementation
regulator: act8865: Remove unneeded regulator_unregister() calls
regulator: s2mps11: Clean up redundant code
regulator: tps65910: Simplify setting enable_mask for regulators
regulator: act8865: add device tree binding doc
...
New drivers
- Samsung Maxim 14577; Micro USB, Regulator, IRQ Controller and Battery Charger
- TI/National Semiconductor LP3943 I2C GPIO Expander and PWM Generator
Existing driver adaptions
- Expansion of Wolfson Arizona DSP and High-Pass filter controls
- TI TWL6040 default Regmap support and Regcache addition/bypass
- Some nice Smatch catch fixes
- Conversion of TI OMAP-USB and TI TWL6030 to endian neutralness
- ChromeOS EC timing (delay) adaptions and added dependency on OF
- Many constifications of 'struct {mfd_cell,regmap_irq,et. al}'
- Watchdog support added for NVIDIA AS3722
- Convert functions to static in TI AM335x
- Realigned previously defeated functionality in TI AM335x
- IIO ADC-TSC concurrency dead-lock/timeout resolution
- Addition of Power Management and Clock support for Samsung core
- DEFINE_PCI_DEVICE_TABLE macro removal from MFD Subsystem
- Greater use of irqdomain functionality in ST-E AB8500
- Removal of 'include/linux/mfd/abx500/ab8500-gpio.h'
- Wolfson WM831x PMIC Power Management changes s/poweroff/shutdown/
- Device Tree documentation added for TI/Nat Semi LP3943
- Version detection and voltage tables for TI TPS6586x PMIC devices
- Simplification of Freescale MC13XXX (de-)initialisation routines
- Clean-up and simplification of the Realtek parent driver
- Added support for RTL8402 Realtek PCI-Express card reader
- Resource leak fix for Maxim 77686
- Possible suspend BUG() fix in OMAP USB TLL
- Support for new Wolfson WM5110 Revision (D)
- Testing of automatic assignment of of_node in mfd_add_device()
- Reversion of the above when it started to cause issues
- Remove legacy Platform Data from;
TI TWL Core, Qualcomm SSBI and ST-E ABx500 Pinctrl
- Clean-ups; tabbing issues, function name changes, 'drvdata = NULL' removal,
unused uninitialised warning mitigation, error message clarity,
removal of redundant/duplicate checks, licensing (GPL -> GPL2),
coding consistency, duplicate function declaration, ret checks,
commit corrections, redundant of_match_ptr() helper removal,
spelling, #if-deffery removal and header guards name changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=PuTE
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.14-1' of git://git.linaro.org/people/ljones/mfd
Pull MFD changes from Lee Jones:
"New drivers
- Samsung Maxim 14577; Micro USB, Regulator, IRQ Controller and
Battery Charger
- TI/National Semiconductor LP3943 I2C GPIO Expander and PWM
Generator
Existing driver adaptions
- Expansion of Wolfson Arizona DSP and High-Pass filter controls
- TI TWL6040 default Regmap support and Regcache addition/bypass
- Some nice Smatch catch fixes
- Conversion of TI OMAP-USB and TI TWL6030 to endian neutralness
- ChromeOS EC timing (delay) adaptions and added dependency on OF
- Many constifications of 'struct {mfd_cell,regmap_irq,et.al}'
- Watchdog support added for NVIDIA AS3722
- Convert functions to static in TI AM335x
- Realigned previously defeated functionality in TI AM335x
- IIO ADC-TSC concurrency dead-lock/timeout resolution
- Addition of Power Management and Clock support for Samsung core
- DEFINE_PCI_DEVICE_TABLE macro removal from MFD Subsystem
- Greater use of irqdomain functionality in ST-E AB8500
- Removal of 'include/linux/mfd/abx500/ab8500-gpio.h'
- Wolfson WM831x PMIC Power Management changes s/poweroff/shutdown/
- Device Tree documentation added for TI/Nat Semi LP3943
- Version detection and voltage tables for TI TPS6586x PMIC devices
- Simplification of Freescale MC13XXX (de-)initialisation routines
- Clean-up and simplification of the Realtek parent driver
- Added support for RTL8402 Realtek PCI-Express card reader
- Resource leak fix for Maxim 77686
- Possible suspend BUG() fix in OMAP USB TLL
- Support for new Wolfson WM5110 Revision (D)
- Testing of automatic assignment of of_node in mfd_add_device()
- Reversion of the above when it started to cause issues
- Remove legacy Platform Data from;
TI TWL Core, Qualcomm SSBI and ST-E ABx500 Pinctrl
- Clean-ups; tabbing issues, function name changes, 'drvdata = NULL'
removal, unused uninitialised warning mitigation, error
message clarity, removal of redundant/duplicate checks,
licensing (GPL -> GPL2), coding consistency, duplicate
function declaration, ret checks, commit corrections,
redundant of_match_ptr() helper removal, spelling,
#if-deffery removal and header guards name changes"
* tag 'mfd-3.14-1' of git://git.linaro.org/people/ljones/mfd: (78 commits)
mfd: wm5110: Add register patch for rev D chip
mfd: omap-usb-tll: Don't hold lock during pm_runtime_get/put_sync()
gpio: lp3943: Remove redundant of_match_ptr helper
mfd: sta2x11-mfd: Use named constants for pci_power_t values
Documentation: mfd: Fix LDO index in s2mps11.txt
mfd: Cleanup mfd-mcp-sa11x0.h header
mfd: max8997: Use "IS_ENABLED(CONFIG_OF)" for DT code.
mfd: twl6030: Fix endianness problem in IRQ handler
mfd: sec-core: Add cells for S5M8767-clocks
mfd: max14577: Remove redundant of_match_ptr helper
mfd: twl6040: Fix sparse non static symbol warning
mfd: Revert "mfd: Always assign of_node in mfd_add_device()"
mfd: rtsx: Fix sparse non static symbol warning
mfd: max77693: Set proper maximum register for MUIC regmap
mfd: max77686: Fix regmap resource leak on driver remove
mfd: Represent correct filenames in file headers
mfd: rtsx: Add support for card reader rtl8402
mfd: rtsx: Add set pull control macro and simplify rtl8411
mfd: max8997: Enforce mfd_add_devices() return value check
mfd: mc13xxx: Simplify probe() & remove()
...
It was holiday season, so no wonder that there are little changes in
framework level, although diffstat shows quite many changes spreaded
over sound/* directories. Most of changes are cleanups, code
refactoring and fixes.
Some highlights:
- Removal of OSS sleep_on usages by Arnd
- Simplified memalloc helper codes, drop obsoleted features;
now it's built into PCM driver instead of an individual module
- Warn if PCM buffer preallocation fails, which will show page
allocation issues more clearly
- Compress offload API updates for sample rates by Vinod
- PCM glitch workaround on ctxfi emu20k1 by Sarah
- Drop cs46xx DSP blobs, using firmware loader now
- USB-audio quitks for Plantronics Gamecom 780, Creative VF0420,
and Focusrite Saffire 6
HD-audio specifics:
- Standardize Kconfigs of HD-audio codec drivers;
now "make localmodconfig" recognizes configs properly (finally!)
- Parallel PM implementation by Mengdong
- BayleyBay/ValleyView2 board fixups
- Broadwell audio support
- Runtime PM improvement (PantherPoint, etc)
- Quirks: Dell subwooer, Gigabyte mobo jack detection oddity,
Dell AiO click noise fixes, Dell headset mic fixes, etc
- Automatic bind with HDMI codec parser without generic parser
- More AD codec fixes (since 3.12 regression) including the automatic
stereo mix support
- Common Thinkpad ACPI helper for Realtek and Conexant codecs
ASoC specifics:
- Update to the generic DMA code to support deferred probe and managed
resources
- New drivers for BCM2835 (used in Raspberry Pi), Tegra with MAX98090
and Analog Devices AXI I2S and S/PDIF controller IPs
- Device tree support for the simple card, max98090 and cs42l52
- Conversion of the Samsung drivers to native dmaengine, making them
multiplatform compatible and hopefully helping keep them more modern
and up to date.
- More regmap conversions, including a very welcome one for twl6040
from Peter Ujfalusi
- A big overhaul of the DaVinci drivers also from Peter Ujfalusi
- Lots of DMA updates from Lars-Peter
- Improvements to the constraints handling code from Lars-Peter
- A very helpful conversion of the TWL4030 driver to regmap from Peter
- A new driver for the Freescale ESAI controller from Nicolin Chen
- Conversion of some of the drivers to use params_width()
- Extensions to DPCM for use with compressed audio from Liam
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=IWy2
-----END PGP SIGNATURE-----
Merge tag 'sound-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"It was holiday season, so no wonder that there are little changes in
framework level, although diffstat shows quite many changes spreaded
over sound/* directories. Most of changes are cleanups, code
refactoring and fixes.
Some highlights:
- Removal of OSS sleep_on usages by Arnd
- Simplified memalloc helper codes, drop obsoleted features; now it's
built into PCM driver instead of an individual module
- Warn if PCM buffer preallocation fails, which will show page
allocation issues more clearly
- Compress offload API updates for sample rates by Vinod
- PCM glitch workaround on ctxfi emu20k1 by Sarah
- Drop cs46xx DSP blobs, using firmware loader now
- USB-audio quitks for Plantronics Gamecom 780, Creative VF0420, and
Focusrite Saffire 6
HD-audio specifics:
- Standardize Kconfigs of HD-audio codec drivers; now "make
localmodconfig" recognizes configs properly (finally!)
- Parallel PM implementation by Mengdong
- BayleyBay/ValleyView2 board fixups
- Broadwell audio support
- Runtime PM improvement (PantherPoint, etc)
- Quirks: Dell subwooer, Gigabyte mobo jack detection oddity, Dell
AiO click noise fixes, Dell headset mic fixes, etc
- Automatic bind with HDMI codec parser without generic parser
- More AD codec fixes (since 3.12 regression) including the automatic
stereo mix support
- Common Thinkpad ACPI helper for Realtek and Conexant codecs
ASoC specifics:
- Update to the generic DMA code to support deferred probe and
managed resources
- New drivers for BCM2835 (used in Raspberry Pi), Tegra with MAX98090
and Analog Devices AXI I2S and S/PDIF controller IPs
- Device tree support for the simple card, max98090 and cs42l52
- Conversion of the Samsung drivers to native dmaengine, making them
multiplatform compatible and hopefully helping keep them more
modern and up to date.
- More regmap conversions, including a very welcome one for twl6040
from Peter Ujfalusi
- A big overhaul of the DaVinci drivers also from Peter Ujfalusi
- Lots of DMA updates from Lars-Peter
- Improvements to the constraints handling code from Lars-Peter
- A very helpful conversion of the TWL4030 driver to regmap from Peter
- A new driver for the Freescale ESAI controller from Nicolin Chen
- Conversion of some of the drivers to use params_width()
- Extensions to DPCM for use with compressed audio from Liam"
* tag 'sound-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (396 commits)
ASoC: dapm: Fix double prefix addition
ASoC: compress: Add suport for DPCM into compressed audio
ASoC: DPCM: make some DPCM API calls non static for compressed usage
ASoC: core: Fix possible NULL pointer dereference of pcm->config
ALSA: hda - add headset mic detect quirks for some Dell machines
ASoC: tlv320aic32x4: Fix regmap range_min
ASoC: core: Return -ENOTSUPP from set_sysclk() if no operation provided
ASoC: dapm: Change prototype of soc_widget_read
ASoC: samsung: Remove SND_DMAENGINE_PCM_FLAG_NO_RESIDUE flag
ASoC: axi-{spdif,i2s}: Remove SND_DMAENGINE_PCM_FLAG_NO_RESIDUE flag
ASoC: generic-dmaengine-pcm: Check DMA residue granularity
ASoC: generic-dmaengine-pcm: Check NO_RESIDUE flag at runtime
dma: pl330: Set residue_granularity
dma: Indicate residue granularity in dma_slave_caps
ASoC: simple-card: fix one bug to writing to the platform data
ASoC: pcm: Use snd_pcm_rate_mask_intersect() helper
ALSA: Add helper function for intersecting two rate masks
ASoC: s6000: Don't mix SNDRV_PCM_RATE_CONTINUOUS with specific rates
ASoC: fsl: Don't mix SNDRV_PCM_RATE_CONTINUOUS with specific rates
ASoC: pcm: Properly initialize hw->rate_max
...
- New driver for the Qualcomm TLMM pin controller and its
msm8x74 subdriver.
- New driver for the Broadcom Capri BCM281xx SoC.
- New subdriver for the imx25 pin controller.
- New subdriver for the Tegra124 pin controller.
- Lock GPIO lines as IRQs for select combined pin control and
GPIO drivers for baytrail and sirf.
- Some semi-big refactorings and extenstions to the sirf
driver.
- Lots of patching, cleanup and fixing in the Renesas "PFC"
driver and associated subdrivers as usual. It is settling
down a little bit now it seems.
- Minor fixes and incremental updates here and there as usual.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJS3mvwAAoJEEEQszewGV1zc3wP/RYjFaS4WGXX/QnvXGlTwpyb
3IIQM4l507ds97ipjip9OO31od8HqkWw4lREwKvRdtqItZJiSzG3oYwn+ro+X2E5
tif0kDxae1tFWieVjA2+zuvjZ76ve8FsVUuUTY7qdd4jdD3OO6P9BgDT0QqwN1Uh
QToszugQzeOqJARn/DKHg2hkBlg0NorasskCvy6qALbXkWIpLm0U4di2HmGgvV2e
5YqRCA8uAf48fE6Q93PQNYQU7Zux1Lyr59y0Wl/pnfKKvi1qG2KPnHDJhMmUbxJk
tWi2VcB1Msrhccv+o0onNMfILG0xInmss3NELTTJJEhSjDvaETkng9fCbw4XDaKY
KLQ7aRjodbGlvdAONqzZR6e0Ra+piGKDdm94+hvOn0BS1SVfjVA7d6AaeTdR6g+6
GD+EVqzczAtla8g1xwNKp69SDN1I3yddMQzjQProSE/eGaQYN6aJW+2hDpD3SoOD
uezFyktzehCIJ5WOIcth8RapN7p33w7bbDOuGVESCesF4NcaUqF+19ukAN9kzVhd
6oksU1RsxLUdBg/zO7Dwyuhx0XzOuBvrP3EADU37MpnTyCGz4ko4vH0T7JHaA5Oe
lN9otYBZT0p/kYUEdINjF3foc7f2yc8adC5kDUB9p/zdzyPIwCijGGD6shJGr11/
7SQ8DvyJZeq3lSNs8+RG
=ol2E
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull bulk pin control changes from Linus Walleij:
"This has been queued and tested for a while. Lots of action here,
like in the GPIO tree, embedded stuff like this is really hot now it
seems. Details in the signed tag. I'm especially happy about the
Qualcomm driver as it is used in such a huge subset of mobile handsets
out there, and these platforms in general need better upstream support
- New driver for the Qualcomm TLMM pin controller and its msm8x74
subdriver.
- New driver for the Broadcom Capri BCM281xx SoC.
- New subdriver for the imx25 pin controller.
- New subdriver for the Tegra124 pin controller.
- Lock GPIO lines as IRQs for select combined pin control and GPIO
drivers for baytrail and sirf.
- Some semi-big refactorings and extenstions to the sirf driver.
- Lots of patching, cleanup and fixing in the Renesas "PFC" driver
and associated subdrivers as usual. It is settling down a little
bit now it seems.
- Minor fixes and incremental updates here and there as usual"
* tag 'pinctrl-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (72 commits)
pinctrl: sunxi: Honor GPIO output initial vaules
pinctrl: capri: add dependency on OF
ARM: bcm11351: Enable pinctrl for Broadcom Capri SoCs
ARM: pinctrl: Add Broadcom Capri pinctrl driver
pinctrl: Add pinctrl binding for Broadcom Capri SoCs
pinctrl: Add void * to pinctrl_pin_desc
pinctrl: st: Fix a typo in probe
pinctrl: Fix some typos and grammar issues in the documentation
pinctrl: sirf: lock IRQs when starting them
pinctrl: sirf: put gpio interrupt pin into input status automatically
pinctrl: sirf: use only one irq_domain for the whole device node
pinctrl: single: fix infinite loop caused by bad mask
pinctrl: single: fix pcs_disable with bits_per_mux
pinctrl: single: fix DT bindings documentation
pinctrl: as3722: Set pin to output mode for some function
pinctrl: sirf: add pin group for USP0 with only RX or TX frame sync
pinctrl: sirf: fix the pins of sdmmc5 connected with TriG
pinctrl: sirf: add lost usp1_uart_nostreamctrl group for atlas6
pinctrl: sunxi: Add Allwinner A20 clock output pin functions
pinctrl/lantiq: fix typo
...
The original author(s) probably copy/pasted these headers from the
existing public header files.
Signed-off-by: Laszlo Papp <lpapp@kde.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
mc13xxx_get_flags() declaration given twice.
This patch removes this duplicate.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use the VERSIONCRC to determine the exact device version. According to
the datasheet this register can be used as device identifier. The
identification is needed since some tps6586x regulators use a different
voltage table.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
LP3943 has 16 output pins which can be used as GPIO expander and PWM generator.
* Regmap I2C interface for R/W LP3943 registers
* Atomic operations for output pin assignment
The driver should check whether requested pin is available or not.
If the pin is already used, pin request returns as a failure.
A driver data, 'pin_used' is checked when gpio_request() and
pwm_request() are called. If the pin is available, then pin_used is set.
And it is cleared when gpio_free() and pwm_free().
* Device tree support
Compatible strings for GPIO and PWM driver.
LP3943 platform data is PWM related, so parsing the device tree is
implemented in the PWM driver.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This deletes the special AB8500 GPIO platform data passing
header and merges the few remaining contents down into the
abx500 pinctrl driver which handles the abx500 GPIO device.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This deletes all instances where the AB8500 GPIO platform
data is passed around. It is completely unused in the kernel
now, so it does not hurt anyone.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds max14577 core/irq driver to support MUIC(Micro USB IC)
device and charger device and support irq domain method to control
internal interrupt of max14577 device. Also, this patch supports DT
binding with max14577_i2c_parse_dt().
The MAXIM 14577 chip contains Micro-USB Interface Circuit and Li+ Battery
Charger. It contains accessory and USB charger detection logic. It supports
USB 2.0 Hi-Speed, UART and stereo audio signals over Micro-USB connector.
The battery charger is compliant with the USB Battery Charging Specification
Revision 1.1. It has also SFOUT LDO output for powering USB devices.
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here's the big drivers/staging/ update for 3.14-rc1
Lots and lots of cleanups, IIO driver updates are also mixed in here due
to the subsystem still crossing staging and drivers/iio/, and the dwc2
driver is moved out of staging. There's a new driver (rts5208), which
ends up making us adding more lines than removing, but overall there was
lots of work toward moving code out of here, which was good.
All of this has been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlLdiE8ACgkQMUfUDdst+ynmYgCcDI9d1Jjo42+tpilIl3hOEb/f
sF8An1W3HRXM3XPG+X1POqprMAk0Jt63
=1Ztu
-----END PGP SIGNATURE-----
Merge tag 'staging-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver tree changes from Greg KH:
"Here's the big drivers/staging/ update for 3.14-rc1
Lots and lots of cleanups, IIO driver updates are also mixed in here
due to the subsystem still crossing staging and drivers/iio/, and the
dwc2 driver is moved out of staging. There's a new driver (rts5208),
which ends up making us adding more lines than removing, but overall
there was lots of work toward moving code out of here, which was good
All of this has been in linux-next with no reported issues"
* tag 'staging-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1084 commits)
lustre: delete linux/lustre_debug.h
staging: lustre: remove some unused debug macros
usb: dwc2: move device tree bindings doc to correct place
staging: vt6656: sparse fixes: iwctl_giwgenie use memcpy.
staging: vt6656: sparse fixes: iwctl_siwgenie use memcpy.
staging: vt6656: sparse fixes ethtool_ioctl Use struct ifreq *
staging: vt6656: sparse fixes: dpc.c missing dpc.h
staging: lustre: libcfs_debug: small whitespace cleanups
staging: lustre: libcfs_debug.h: remove extra blank lines
staging: lustre: libcfs_debug.h: Align backslashes in macros
staging: lustre: libcfs_debug.h: align define values
staging: tidspbridge: adjust error return code (bugfix)
Staging: rts5139: rts51x_card: fixed style issues
staging: wlags49_h2: Fix "do not use C99 //" in wl_cs.h, wl_enc.h wl_main.h and wl_wext.h
Staging: rtl8188eu: Fixed "foo * bar" related coding style issues
Staging: rtl8188eu: Fixed required spaces after ',' and around '=' and '=='
staging: vt6655: Fix memory leak in wpa_ioctl()
imx-drm: parallel-display: honor 'native-mode' property when selecting video mode from DT
staging: drm/imx: don't drop crtc offsets when doing pageflip
staging: drm/imx: handle framebuffer offsets correctly
...
If pins are used for function output like pwm, clk32k,
power good etc then set it as output mode default.
Signed-off-by: Mallikarjun Kasoju <mkasoju@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The accessibility checking method to the higher register was added by
69d1fe18e9 (mmc: tmio: only access registers above 0xff, if available)
But, it doesn't care 32bit register. It is impossible to calculate it
from the resource size, since there is 16/32 bit register IP (e.g. VERSION
is located on 0xe2 if 16bit register, but it is located on 0x1c4 if 32bit
register).
This patch adds new TMIO_MMC_HAVE_HIGH_REG flags, tmio_mmc driver has it,
and sh_mobile_sdhi doesn't have it today.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
.bus_shift is used to 16/32bit register access offset calculation on
tmio driver. tmio_mmc_xxx is used from Toshiba/Renesas now, but this
bus_shift value depends on HW IP. This patch moves .bus_shift to
tmio_mmc_data member and sets it on each driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add the registers necessary to enable/disable the headphone short
circuit protection.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ADC driver always programs all possible ADC values and discards
them except for the value IIO asked for. On the am335x-evm the driver
programs four values and it takes 500us to gather them. Reducing the number
of conversations down to the (required) one also reduces the busy loop down
to 125us.
This leads to another error, namely the FIFOCOUNT register is sometimes
(like one out of 10 attempts) not updated in time leading to EBUSY.
The next read has the FIFOCOUNT register updated.
Checking for the ADCSTAT register for being idle isn't a good choice either.
The problem is that if TSC is used at the same time, the HW completes the
conversation for ADC *and* before the driver noticed it, the HW begins to
perform a TSC conversation and so the driver never seen the HW idle. The
next time we would have two values in the FIFO but since the driver reads
everything we always see the current one.
So instead of polling for the IDLE bit in ADCStatus register, we should
check the FIFOCOUNT register. It should be one instead of zero because we
request one value.
This change in turn leads to another error. Sometimes if TSC & ADC are
used together the TSC starts generating interrupts even if nobody
actually touched the touchscreen. The interrupts seem valid because TSC's
FIFO is filled with values for each channel of the TSC. This condition stops
after a few ADC reads but will occur again. Not good.
On top of this (even without the changes I just mentioned) there is a ADC
& TSC lockup condition which was reported to me by Jeff Lance including the
following test case:
A busy loop of "cat /sys/bus/iio/devices/iio\:device0/in_voltage4_raw"
and a mug on touch screen. With this setup, the hardware will lockup after
something between 20 minutes and it could take up to a couple of hours.
During that lockup, the ADCSTAT register says 0x30 (or 0x70) which means
STEP_ID = IDLE and FSM_BUSY = yes. That means the hardware says that it is
idle and busy at the same time which is an invalid condition.
For all this reasons I decided to rework this TSC/ADC part and add a
handshake / synchronization here:
First the ADC signals that it needs the HW and writes a 0 mask into the
SE register. The HW (if active) will complete the current conversation
and become idle. The TSC driver will gather the values from the FIFO
(woken up by an interrupt) and won't "enable" another conversation.
Instead it will wake up the ADC driver which is already waiting. The ADC
driver will start "its" conversation and once it is done, it will
enable the TSC steps so the TSC will work again.
After this rework I haven't observed the lockup so far. Plus the busy
loop has been reduced from 500us to 125us.
The continues-read mode remains unchanged.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The purpose of reg_se_cache has been defeated. It should avoid the
read-back of the register to avoid the latency and the fact that the
bits are reset to 0 after the individual conversation took place.
The reason why this is required like this to work, is that read-back of
the register removes the bits of the ADC so they do not start another
conversation after the register is re-written from the TSC side for the
update.
To avoid the not required read-back I introduce a "set once" variant which
does not update the cache mask. After the conversation completes, the
bit is removed from the SE register anyway and we don't plan a new
conversation "any time soon". The current set function is renamed to
set_cache to distinguish the two operations.
This is a small preparation for a larger sync-rework.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since the "recent" changes, am335x_tsc_se_update() has no longer any
users outside of this file so make it local.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Improve readability by creating a define for each microphone detection
level.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
SD0 may operate in low-voltage mode, with a minimum of 0.41V
and a maximum of 1.5V. This is indicated by bit 4 of FUSE7.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Vince Hsu <vinceh@nvidia.com>
broonie.e6264@m.evernote.com
Signed-off-by: Mark Brown <broonie@linaro.org>
BBCH_BBCHEN_MASK is equivalent to TPS65910_SUPPLY_STATE_ENABLED.
So all regulators have the same enable_mask setting.
BBCH_BBCHEN_MASK and BBCH_BBCHEN_SHIFT are not used now, remove them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
tps65910 has a backup battery charger with a configurable voltage. This
patch adds a regulator for the backup battery.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Certain use-cases require the DRE to be disabled so expose registers
necessary to control the DRE enables.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove sec_reg* helpers as they are not used anymore. These helpers were
error-prone as they mixed u8 with unsigned int and they changed order of
some of parameters (val and mask in sec_reg_update()).
Also the helpers didn't give any way of useful abstraction as they just
called corresponding regmap function.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch fixes a build failure that appeared in v3.13-rc4 due to an
RTC/MFD update merged via -mm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=t/v5
-----END PGP SIGNATURE-----
Merge tag 's2mps11-build' into regulator-s5m8767 since a following patch
depend on it.
regulator/clk: Fix s2mps11 build
This patch fixes a build failure that appeared in v3.13-rc4 due to an
RTC/MFD update merged via -mm.
Add symbols for hard-coded values of BUCK_RAMP field in DVS_RAMP
register. This simplifies a little the code as register update is called
only once.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Rename old regmap field of "struct sec_pmic_dev" to "regmap_pmic" and
add new regmap for RTC.
On S5M8767A registers were not properly updated and read due to usage of
the same regmap as the PMIC. This could be observed in various hangs,
e.g. in infinite loop during waiting for UDR field change.
On this chip family the RTC has different I2C address than PMIC so
additional regmap is needed.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace hard-coded value for mask used in BUCKX_CTRL registers (for
BUCKX_EN field) with a symbol. This also removes two local variables.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add mx6 hdmi transmitter support.
Original work has been done by Sascha Hauer and Tony Prisk.
Special thanks to Russell King for his carefully review, many bug fixes and
testing of the mx6 HDMI driver.
Tested on the following boards:
- mx6q sabresd
- mx6dl sabresd
- mx6solo wandboard
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=IhEz
-----END PGP SIGNATURE-----
Merge tag 'ib-asoc-1' of git://git.linaro.org/people/ljones/mfd into asoc-arizona
Immutable branch for ASoC, as requested by Mark Brown
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: D.J. Barrow <dbarrow@wolfsonmicro.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
