As described in Documentation/i2c/fault-codes.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: c71bcdcb42 ("i2c: add i2c bus driver for NVIDIA GPU")
Acked-by: Ajay Gupta <ajayg@nvidia.com>
Tested-by: Ajay Gupta <ajayg@nvidia.com>
Add support for the IIC code for the r8a77990 (R-Car E3).
It is not considered compatible with existing fallback bindings
due to the documented absence of automatic transmission registers.
These registers are currently not used by the driver and
thus the provides the same behaviour for "renesas,iic-r8a77990" and
"renesas,rcar-gen3-iic". The point of declaring incompatibility is
to allow for automatic transmission register support to be added to
"renesas,iic-r8a77990" and "renesas,rcar-gen3-iic" in future.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Read SYSCFG bindings to set Fast Mode Plus bits if Fast Mode Plus
speed is selected.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is already done for us internally by the signal machinery.
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Probe deferral is a normal operating condition in the probe function,
so don't spam the log with an error in this case.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Latest NVIDIA GPU card has USB Type-C interface. There is a
Type-C controller which can be accessed over I2C.
This driver adds I2C bus driver to communicate with Type-C controller.
I2C client driver will be part of USB Type-C UCSI driver.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[wsa: kept Makefile sorting]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We need to enable runtime PM on this i2c controller before populating
child devices with i2c_add_adapter(). Otherwise, if a child device uses
runtime PM and stays runtime PM enabled we'll get the following warning
at boot.
Enabling runtime PM for inactive device (a98000.i2c) with active children
[...]
Call trace:
pm_runtime_enable+0xd8/0xf8
geni_i2c_probe+0x440/0x460
platform_drv_probe+0x74/0xc8
[...]
Let's move the runtime PM enabling and setup to before we add the
adapter, so that this device can respond to runtime PM requests from
children.
Fixes: 37692de5d5 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allow I2C_OMAP to be built for K3 platforms.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The IRQ will be mapped in i2c_device_probe only if client->irq is zero and
i2c_device_remove does not clear this. When rebinding an I2C device,
whos IRQ provider has also been rebound this means that an IRQ mapping
will never be created, causing the I2C device to fail to acquire its
IRQ. Fix this issue by clearing client->irq in i2c_device_remove,
forcing i2c_device_probe to lookup the mapping again.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
irq_create_mapping calls irq_find_mapping internally and will use the
found mapping if one exists, so there is no need to manually call this
from i2c_smbus_host_notify_to_irq.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Rework the handling of the P-unit semaphore on Intel Baytrail and
Cherrytrail systems to avoid race conditions and excessive overhead
related to it (Hans de Goede).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=4oYh
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.20-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"Rework the handling of the P-unit semaphore on Intel Baytrail and
Cherrytrail systems to avoid race conditions and excessive overhead
related to it (Hans de Goede)"
* tag 'acpi-4.20-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PMIC: xpower: Add depends on IOSF_MBI to Kconfig entry
i2c: designware: Cleanup bus lock handling
ACPI / PMIC: xpower: Block P-Unit I2C access during read-modify-write
x86: baytrail/cherrytrail: Rework and move P-Unit PMIC bus semaphore code
Pull i2c updates from Wolfram Sang:
"I2C has not so much stuff this time. Mostly driver enablement for new
SoCs, some driver bugfixes, and some cleanups"
* 'i2c/for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (35 commits)
MAINTAINERS: add maintainer for Renesas RIIC driver
i2c: sh_mobile: Remove dummy runtime PM callbacks
i2c: uniphier-f: fix race condition when IRQ is cleared
i2c: uniphier-f: fix occasional timeout error
i2c: uniphier-f: make driver robust against concurrency
i2c: i2c-qcom-geni: Simplify irq handler
i2c: i2c-qcom-geni: Simplify tx/rx functions
i2c: designware: Set IRQF_NO_SUSPEND flag for all BYT and CHT controllers
i2c: mux: mlxcpld: simplify code to reach the adapter
i2c: mux: ltc4306: simplify code to reach the adapter
i2c: mux: pca954x: simplify code to reach the adapter
i2c: core: remove level of indentation in i2c_transfer
i2c: core: remove outdated DEBUG output
i2c: zx2967: use core to detect 'no zero length' quirk
i2c: tegra: use core to detect 'no zero length' quirk
i2c: qup: use core to detect 'no zero length' quirk
i2c: omap: use core to detect 'no zero length' quirk
i2c: Convert to using %pOFn instead of device_node.name
i2c: brcmstb: Allow enabling the driver on DSL SoCs
eeprom: at24: fix unexpected timeout under high load
...
Platform drivers don't need dummy runtime PM callbacks that just return
success and non-NULL pm pointer in their struct device_driver in order
to have runtime PM happening. This has changed since following commits:
05aa55dddb ("PM / Runtime: Lenient generic runtime pm callbacks")
543f2503a9 ("PM / platform_bus: Allow runtime PM by default")
8b313a38ec ("PM / Platform: Use generic runtime PM callbacks directly")
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The current IRQ handler clears all the IRQ status bits when it bails
out. This is dangerous because it might clear away the status bits
that have just been set while processing the current handler. If this
happens, the IRQ event for the latest transfer is lost forever.
The IRQ status bits must be cleared *before* the next transfer is
kicked.
Fixes: 6a62974b66 ("i2c: uniphier_f: add UniPhier FIFO-builtin I2C driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently, a timeout error could happen at a repeated START condition.
For a (non-repeated) START condition, the controller starts sending
data when the UNIPHIER_FI2C_CR_STA bit is set. However, for a repeated
START condition, the hardware starts running when the slave address is
written to the TX FIFO - the write to the UNIPHIER_FI2C_CR register is
actually unneeded.
Because the hardware is already running before the IRQ is enabled for
a repeated START, the driver may miss the IRQ event. In most cases,
this problem does not show up since modern CPUs are much faster than
the I2C transfer. However, it is still possible that a context switch
happens after the controller starts, but before the IRQ register is
set up.
To fix this,
- Do not write UNIPHIER_FI2C_CR for repeated START conditions.
- Enable IRQ *before* writing the slave address to the TX FIFO.
- Disable IRQ for the current CPU while queuing up the TX FIFO;
If the CPU is interrupted by some task, the interrupt handler
might be invoked due to the empty TX FIFO before completing the
setup.
Fixes: 6a62974b66 ("i2c: uniphier_f: add UniPhier FIFO-builtin I2C driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is unlikely to happen, but it is possible for a CPU to enter
the interrupt handler just after wait_for_completion_timeout() has
expired. If this happens, the hardware is accessed from multiple
contexts concurrently.
Disable the IRQ after wait_for_completion_timeout(), and do nothing
from the handler when the IRQ is disabled.
Fixes: 6a62974b66 ("i2c: uniphier_f: add UniPhier FIFO-builtin I2C driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Now that most of the special Bay- / Cherry-Trail bus lock handling has
been moved to the iosf_mbi code we can simplify the remaining code a bit.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On some BYT/CHT systems the SoC's P-Unit shares the I2C bus with the
kernel. The P-Unit has a semaphore for the PMIC bus which we can take to
block it from accessing the shared bus while the kernel wants to access it.
Currently we have the I2C-controller driver acquiring and releasing the
semaphore around each I2C transfer. There are 2 problems with this:
1) PMIC accesses often come in the form of a read-modify-write on one of
the PMIC registers, we currently release the P-Unit's PMIC bus semaphore
between the read and the write. If the P-Unit modifies the register during
this window?, then we end up overwriting the P-Unit's changes.
I believe that this is mostly an academic problem, but I'm not sure.
2) To safely access the shared I2C bus, we need to do 3 things:
a) Notify the GPU driver that we are starting a window in which it may not
access the P-Unit, since the P-Unit seems to ignore the semaphore for
explicit power-level requests made by the GPU driver
b) Make a pm_qos request to force all CPU cores out of C6/C7 since entering
C6/C7 while we hold the semaphore hangs the SoC
c) Finally take the P-Unit's PMIC bus semaphore
All 3 these steps together are somewhat expensive, so ideally if we have
a bunch of i2c transfers grouped together we only do this once for the
entire group.
Taking the read-modify-write on a PMIC register as example then ideally we
would only do all 3 steps once at the beginning and undo all 3 steps once
at the end.
For this we need to be able to take the semaphore from within e.g. the PMIC
opregion driver, yet we do not want to remove the taking of the semaphore
from the I2C-controller driver, as that is still necessary to protect many
other code-paths leading to accessing the shared I2C bus.
This means that we first have the PMIC driver acquire the semaphore and
then have the I2C controller driver trying to acquire it again.
To make this possible this commit does the following:
1) Move the semaphore code from being private to the I2C controller driver
into the generic iosf_mbi code, which already has other code to deal with
the shared bus so that it can be accessed outside of the I2C bus driver.
2) Rework the code so that it can be called multiple times nested, while
still blocking I2C accesses while e.g. the GPU driver has indicated the
P-Unit needs the bus through a iosf_mbi_punit_acquire() call.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO
lines as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can
use only the fastpatch callbacks to enable/disable irqs
like any normal irqchip, especially the gpiod_lock_as_irq()
has been improved to be callable in fastpath context.
A bunch of rework had to be done to achieve this but it is
a big win since I never liked to restrict this to slowpath.
The only call requireing slowpath was try_module_get() and
this is kept at the .request_resources() slowpath callback.
In the GPIO CEC driver this is a big win sine a single
line is used for both outgoing and incoming traffic, and
this needs to use IRQs for incoming traffic while actively
driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a
"cookie" (struct gpio_array) and a bitmap for setting or
getting multiple GPIO lines at once. This improvement
orginated in a specific need to speed up an OMAP1 driver and
has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot
of checks and code when we want things to go really fast.
The previous code would minimize the number of calls
down to the driver callbacks assuming the CPU speed was
orders of magnitude faster than the I/O latency, but this
assumption was wrong on several platforms: what we needed
to do was to profile and improve the speed on the hot
path of the array functions and this change is now
completed.
- Clean out the painful and hard to grasp BNF experiments
from the device tree bindings. Future approaches are looking
into using JSON schema for this purpose. (Rob Herring
is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and
other contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin
control driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver.
-----BEGIN PGP SIGNATURE-----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=YosT
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.20 series:
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO lines
as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can use only
the fastpatch callbacks to enable/disable irqs like any normal
irqchip, especially the gpiod_lock_as_irq() has been improved to be
callable in fastpath context.
A bunch of rework had to be done to achieve this but it is a big
win since I never liked to restrict this to slowpath. The only call
requireing slowpath was try_module_get() and this is kept at the
.request_resources() slowpath callback. In the GPIO CEC driver this
is a big win sine a single line is used for both outgoing and
incoming traffic, and this needs to use IRQs for incoming traffic
while actively driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a "cookie"
(struct gpio_array) and a bitmap for setting or getting multiple
GPIO lines at once.
This improvement orginated in a specific need to speed up an OMAP1
driver and has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot of checks
and code when we want things to go really fast.
The previous code would minimize the number of calls down to the
driver callbacks assuming the CPU speed was orders of magnitude
faster than the I/O latency, but this assumption was wrong on
several platforms: what we needed to do was to profile and improve
the speed on the hot path of the array functions and this change is
now completed.
- Clean out the painful and hard to grasp BNF experiments from the
device tree bindings. Future approaches are looking into using JSON
schema for this purpose. (Rob Herring is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and other
contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin control
driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver"
* tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (116 commits)
gpio: Clarify kerneldoc on gpiochip_set_chained_irqchip()
gpio: Remove unused 'irqchip' argument to gpiochip_set_cascaded_irqchip()
gpio: Drop parent irq assignment during cascade setup
mmc: pwrseq_simple: Fix incorrect handling of GPIO bitmap
gpio: fix SNPS_CREG kconfig dependency warning
gpiolib: Initialize gdev field before is used
gpio: fix kernel-doc after devres.c file rename
gpio: fix doc string for devm_gpiochip_add_data() to not talk about irq_chip
gpio: syscon: Fix possible NULL ptr usage
gpiolib: Show correct direction from the beginning
pinctrl: msm: Use init_valid_mask exported function
gpiolib: Add init_valid_mask exported function
GPIO: add single-register GPIO via CREG driver
dt-bindings: Document the Synopsys GPIO via CREG bindings
gpio: mockup: use device properties instead of platform_data
gpio: Slightly more helpful debugfs
gpio: omap: Remove set but not used variable 'dev'
gpio: omap: drop omap_gpio_list
Accept partial 'gpio-line-names' property.
gpio: omap: get rid of the conditional PM runtime calls
...
DMA needs to be cleaned up not only on timeout, but on all errors where
it has been setup before.
Fixes: 73e8b05283 ("i2c: rcar: add DMA support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We don't need to use goto here, we can just collapse the if statement
and goto chain into multiple branches and then combine some duplicate
completion calls into one big if statement. Let's do it to clean up code
some more.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Alok Chauhan <alokc@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We never really look at the 'ret' local variable in these functions, so
let's remove it to make way for shorter and simpler code. Furthermore,
we can shorten some lines by adding two local variables for the SE and
the message length so that everything fits in 80 columns and testing the
'dma_buf' local variable in lieu of the 'mode' local variable. And
kernel style is to leave the return statement by itself, detached from
the rest of the function.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Alok Chauhan <alokc@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On some Cherry Trail systems the GPU ACPI fwnode has power-resources which
point to the PMIC, which is connected over a LPSS I2C controller. The GPU
is a PCI device and PCI devices are powered-on at the resume_noirq resume
phase.
Since the GPU power-resources need the I2C controller, recent acpi_lpss.c
changes now also power-up the LPSS I2C controllers on BYT and CHT devices
in the resume_noirq resume phase. But during this phase the IRQ of the
controller is disabled leading to these errors:
i2c_designware 808622C1:06: controller timed out
ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion]
ACPI Error: Method parse/execution failed \_SB.P18W._ON, AE_ERROR
video LNXVIDEO:00: Failed to change power state to D0
This commit makes the i2c-designware controller set the IRQF_NO_SUSPEND
flag when requesting the interrupt on BYT and CHT devices, so that the IRQ
is left enabled during the noirq phase, fixing this.
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This function was renamed in commit 82fe39a6bc ("i2c: refactor
function to release a DMA safe buffer") but this kernel doc wasn't
updated to point at the new function. Rename it.
Fixes: 82fe39a6bc ("i2c: refactor function to release a DMA safe buffer")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
struct i2c_client has a direct pointer to the adapter, no need to dig
it out of the struct device tree.
Suggested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
struct i2c_client has a direct pointer to the adapter, no need to dig
it out of the struct device tree.
Suggested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
struct i2c_client has a direct pointer to the adapter, no need to dig
it out of the struct device tree.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
Using the common kernel pattern to bail out at the beginning if some
conditions are not met, we can save a level of indentation. No
functional change.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The usefulness of this debug output is questionable. It covers only
direct i2c_transfer calls and no SMBUS calls, neither direct nor
emulated ones. And the latter one is largely used in the kernel, so a
lot of stuff is missed. False positives are also generated in case the
locking later fails. Also, we have a proper tracing mechanism for all
these kinds of transfers in place for years now. Remove this old one.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
And don't reimplement in the driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
And don't reimplement in the driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
And don't reimplement in the driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
And don't reimplement in the driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Single patch from Wang Xin improving the read/write loop in at24
under high load.
-----BEGIN PGP SIGNATURE-----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=/lJE
-----END PGP SIGNATURE-----
Merge tag 'at24-4.20-updates-for-wolfram' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into i2c/for-4.20
AT24 updates for 4.20
Single patch from Wang Xin improving the read/write loop in at24
under high load.
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
ARCH_BCM_63XX which is used by ARM-based DSL SoCs from Broadcom uses the
same controller, make it possible to select the STB driver and update
the Kconfig and help text a bit.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There are platforms which don't provide input clock rate but provide
I2C timing parameters. Commit 3bd4f27727 ("i2c: designware: Call
i2c_dw_clk_rate() only once in i2c_dw_init_master()") causes needless
warning during probe on those platforms since i2c_dw_clk_rate(), which
causes the warning when input clock is unknown, is called even when
there is no need to calculate timing parameters.
Fixes: 3bd4f27727 ("i2c: designware: Call i2c_dw_clk_rate() only once in i2c_dw_init_master()")
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: <stable@vger.kernel.org> # 4.19
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-scmi driver crashes when the SMBus Write Block transaction is
executed:
WARNING: CPU: 9 PID: 2194 at mm/page_alloc.c:3931 __alloc_pages_slowpath+0x9db/0xec0
Call Trace:
? get_page_from_freelist+0x49d/0x11f0
? alloc_pages_current+0x6a/0xe0
? new_slab+0x499/0x690
__alloc_pages_nodemask+0x265/0x280
alloc_pages_current+0x6a/0xe0
kmalloc_order+0x18/0x40
kmalloc_order_trace+0x24/0xb0
? acpi_ut_allocate_object_desc_dbg+0x62/0x10c
__kmalloc+0x203/0x220
acpi_os_allocate_zeroed+0x34/0x36
acpi_ut_copy_eobject_to_iobject+0x266/0x31e
acpi_evaluate_object+0x166/0x3b2
acpi_smbus_cmi_access+0x144/0x530 [i2c_scmi]
i2c_smbus_xfer+0xda/0x370
i2cdev_ioctl_smbus+0x1bd/0x270
i2cdev_ioctl+0xaa/0x250
do_vfs_ioctl+0xa4/0x600
SyS_ioctl+0x79/0x90
do_syscall_64+0x73/0x130
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
ACPI Error: Evaluating _SBW: 4 (20170831/smbus_cmi-185)
This problem occurs because the length of ACPI Buffer object is not
defined/initialized in the code before a corresponding ACPI method is
called. The obvious patch below fixes this issue.
Signed-off-by: Edgar Cherkasov <echerkasov@dev.rtsoft.ru>
Acked-by: Viktor Krasnov <vkrasnov@dev.rtsoft.ru>
Acked-by: Michael Brunner <Michael.Brunner@kontron.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Trivial fix to spelling mistake in dev_notice message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We shouldn't attempt to DMA map the message buffers passed into this
driver from the i2c core unless the message we're mapping have been
properly setup for DMA. The i2c core indicates such a situation by
setting the I2C_M_DMA_SAFE flag, so check for that flag before using DMA
mode. We can also bounce the buffer if it isn't already mapped properly
by using the i2c_get_dma_safe_msg_buf() APIs, so do that when we
want to use DMA for a message.
This fixes a problem where the kernel oopses cleaning pages for a buffer
that's mapped into the vmalloc space. The pages are returned from
request_firmware() and passed down directly to the i2c master to write
to the i2c touchscreen device. Mapping vmalloc buffers with
dma_map_single() won't work reliably, causing an oops like below:
Unable to handle kernel paging request at virtual address ffffffc01391d000
...
Reported-by: Philip Chen <philipchen@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Replace "fallthru" with a proper "fall through" annotation.
This fix is part of the ongoing efforts to enabling
-Wimplicit-fallthrough
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The function that computes clock parameters from divisors did not
respect the maximum size of the bitfields that the parameters were
written to. This fixes the bug.
This bug can be reproduced with (and this fix verified with) the test
at: https://kunit-review.googlesource.com/c/linux/+/1035/
Discovered-by-KUnit: https://kunit-review.googlesource.com/c/linux/+/1035/
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Reviewed-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use a better annotation, so GCC won't complain anymore:
drivers/i2c/busses/i2c-aspeed.c:458:15: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 3e9efc3299 ("i2c: aspeed: Handle master/slave combined irq events
properly") moved interrupt acknowledgment to the end of the interrupt
handler. In part this was done because the AST2500 datasheet says:
I2CD10 Interrupt Status Register
bit 2 Receive Done Interrupt status
S/W needs to clear this status bit to allow next data receiving.
Acknowledging Receive Done before receive data was handled resulted in
receive errors on high speed I2C busses.
However, interrupt acknowledgment was not only moved to the end of the
interrupt handler for Receive Done Interrupt status, but for all interrupt
status bits. This could result in race conditions if a second interrupt was
received during interrupt handling and not handled but still acknowledged
at the end of the interrupt handler.
Acknowledge only "Receive Done Interrupt status" late in the interrupt
handler to solve the problem.
Fixes: 3e9efc3299 ("i2c: aspeed: Handle master/slave combined irq events properly")
Cc: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Cc: Joel Stanley <joel@jms.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Acked-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In order to make use of array info obtained from gpiod_get_array() and
speed up processing of arrays matching single GPIO chip layout, that
information must be passed to get/set array functions. Extend the
functions' API with that additional parameter and update all users.
Pass NULL if a user builds an array itself from single GPIOs.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Most users of get/set array functions iterate consecutive bits of data,
usually a single integer, while processing array of results obtained
from, or building an array of values to be passed to those functions.
Save time wasted on those iterations by changing the functions' API to
accept bitmaps.
All current users are updated as well.
More benefits from the change are expected as soon as planned support
for accepting/passing those bitmaps directly from/to respective GPIO
chip callbacks if applicable is implemented.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Disable interrupts while configuring the transfer and enable them back.
We have below as the programming sequence
1. start and slave address
2. byte count and stop
In some customer platform there was a lot of interrupts between 1 and 2
and after slave address (around 7 clock cyles) if 2 is not executed
then the transaction is nacked.
To fix this case make the 2 writes atomic.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[wsa: added a newline for better readability]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
In most of cases, interrupt bits are set one by one but there are
also a lot of other cases that Aspeed I2C IP sends multiple
interrupt bits with combining master and slave events using a
single interrupt call. It happens much more in multi-master
environment than single-master. For an example, when master is
waiting for a NORMAL_STOP interrupt in its MASTER_STOP state,
SLAVE_MATCH and RX_DONE interrupts could come along with the
NORMAL_STOP in case of an another master immediately sends data
just after acquiring the bus. In this case, the NORMAL_STOP
interrupt should be handled by master_irq and the SLAVE_MATCH and
RX_DONE interrupts should be handled by slave_irq. This commit
modifies irq hadling logic to handle the master/slave combined
events properly.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
DMA mode will always be used in i2c transactions, try to allocate
a DMA safe buffer if the buf of struct i2c_msg used is not DMA safe.
Signed-off-by: Jun Gao <jun.gao@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit a3d411fb38 ("i2c: designware: Disable pm for PMIC i2c-bus even if
there is no _SEM method"), always set the pm_disabled flag on the I2C7
controller, even if its bus was not shared with the PUNIT.
This was a workaround for various suspend/resume issues, after the
following 2 commits this workaround is no longer necessary:
Commit 5415277283 ("PM: i2c-designware-platdrv: Suspend/resume at the
late/early stages")
Commit e6ce0ce34f ("ACPI / LPSS: Add device link for CHT SD card
dependency on I2C")
Therefor this commit removes this workaround.
After this commit the pm_disabled flag is only used to indicate that the
bus is shared with the PUNIT and after other recent changes we no longer
call dev_pm_syscore_device(dev, true), so we are no longer actually
disabling (non-runtime) pm, so this commit also renames the flag to
shared_with_punit to better reflect what it is for.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
DNV's iTCO is slightly different with SMBCTRL sitting at a different
offset when compared to all other devices. Let's fix so that we can
properly use iTCO watchdog.
Fixes: 84d7f2ebd7 ("i2c: i801: Add support for Intel DNV")
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Microsemi Ocelot I2C controller is a designware IP. It also has a
second set of registers to allow tweaking SDA hold time and spike
filtering.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
[wsa: made one function static]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Because some old designware IPs were not supporting setting an SDA hold
time, vendors developed their own solution. Add a way for the final driver
to provide its own SDA hold time handling.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move the #ifdef CONFIG_OF section to the top of the file, after the ACPI
section so functions defined there can be used in dw_i2c_plat_probe.
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Switch to device_get_match_data in probe to match the device specific data
instead of using the acpi specific function.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
mx8dv never entered into production and there is no other place
in the kernel referring to this SoC, so remove it from the
driver's compatible entry.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver currently emits a STOP if the next message is not
I2C_MD_RD. It should not do it because it disturbs the I2C_RDWR
ioctl, where read/write transactions are combined without STOP
between.
Issue STOP only when the message is the last one _or_ flagged with
I2C_M_STOP.
Fixes: 6a62974b66 ("i2c: uniphier_f: add UniPhier FIFO-builtin I2C driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver currently emits a STOP if the next message is not
I2C_MD_RD. It should not do it because it disturbs the I2C_RDWR
ioctl, where read/write transactions are combined without STOP
between.
Issue STOP only when the message is the last one _or_ flagged with
I2C_M_STOP.
Fixes: dd6fd4a327 ("i2c: uniphier: add UniPhier FIFO-less I2C driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We only freed the bounce buffer after successful DMA, missing the cases
where DMA setup may have gone wrong. Use a better location which always
gets called after each message and use 'stop_after_dma' as a flag for a
successful transfer.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
After various refactoring over the years, start_ch() doesn't return
errno anymore, so make the function return void. This saves the error
handling when calling it which in turn eases cleanup of resources of a
future patch.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
a) rename to 'put' instead of 'release' to match 'get' when obtaining
the buffer
b) change the argument order to have the buffer as first argument
c) add a new argument telling the function if the message was
transferred. This allows the function to be used also in cases
where setting up DMA failed, so the buffer needs to be freed without
syncing to the message buffer.
Also convert the only user.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Yep, I went looking for one of these, and I wasn't able to find it
easily. That's worse than a line which is 82-chars long, IMHO.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On Bay Trail and Cherry Trail devices we set the pm_disabled flag for I2C
busses which the OS shares with the PUNIT as these need special handling.
Until now we called dev_pm_syscore_device(dev, true) for I2C controllers
with this flag set to keep these I2C controllers always on.
After commit 12864ff854 ("ACPI / LPSS: Avoid PM quirks on suspend and
resume from hibernation"), this no longer works. This commit modifies
lpss_iosf_exit_d3_state() to only run if lpss_iosf_enter_d3_state() has ran
before it, so that it does not run on a resume from hibernate (or from S3).
On these systems the conditions for lpss_iosf_enter_d3_state() to run
never become true, so lpss_iosf_exit_d3_state() never gets called and
the 2 LPSS DMA controllers never get forced into D0 mode, instead they
are left in their default automatic power-on when needed mode.
The not forcing of D0 mode for the DMA controllers enables these systems
to properly enter S0ix modes, which is a good thing.
But after entering S0ix modes the I2C controller connected to the PMIC
no longer works, leading to e.g. broken battery monitoring.
The _PS3 method for this I2C controller looks like this:
Method (_PS3, 0, NotSerialized) // _PS3: Power State 3
{
If ((((PMID == 0x04) || (PMID == 0x05)) || (PMID == 0x06)))
{
Return (Zero)
}
PSAT |= 0x03
Local0 = PSAT /* \_SB_.I2C5.PSAT */
}
Where PMID = 0x05, so we enter the Return (Zero) path on these systems.
So even if we were to not call dev_pm_syscore_device(dev, true) the
I2C controller will be left in D0 rather then be switched to D3.
Yet on other Bay and Cherry Trail devices S0ix is not entered unless *all*
I2C controllers are in D3 mode. This combined with the I2C controller no
longer working now that we reach S0ix states on these systems leads to me
believing that the PUNIT itself puts the I2C controller in D3 when all
other conditions for entering S0ix states are true.
Since now the I2C controller is put in D3 over a suspend/resume we must
re-initialize it afterwards and that does indeed fix it no longer working.
This commit implements this fix by:
1) Making the suspend_late callback a no-op if pm_disabled is set and
making the resume_early callback skip the clock re-enable (since it now was
not disabled) while still doing the necessary I2C controller re-init.
2) Removing the dev_pm_syscore_device(dev, true) call, so that the suspend
and resume callbacks are actually called. Normally this would cause the
ACPI pm code to call _PS3 putting the I2C controller in D3, wreaking havoc
since it is shared with the PUNIT, but in this special case the _PS3 method
is a no-op so we can safely allow a "fake" suspend / resume.
Fixes: 12864ff854 ("ACPI / LPSS: Avoid PM quirks on suspend and resume ...")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200861
Cc: 4.15+ <stable@vger.kernel.org> # 4.15+
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 7ae81952cda ("i2c: i801: Allow ACPI SystemIO OpRegion to conflict
with PCI BAR") made it possible for AML code to access SMBus I/O ports
by installing custom SystemIO OpRegion handler and blocking i80i driver
access upon first AML read/write to this OpRegion.
However, while ThinkPad T560 does have SystemIO OpRegion declared under
the SMBus device, it does not access any of the SMBus registers:
Device (SMBU)
{
...
OperationRegion (SMBP, PCI_Config, 0x50, 0x04)
Field (SMBP, DWordAcc, NoLock, Preserve)
{
, 5,
TCOB, 11,
Offset (0x04)
}
Name (TCBV, 0x00)
Method (TCBS, 0, NotSerialized)
{
If ((TCBV == 0x00))
{
TCBV = (\_SB.PCI0.SMBU.TCOB << 0x05)
}
Return (TCBV) /* \_SB_.PCI0.SMBU.TCBV */
}
OperationRegion (TCBA, SystemIO, TCBS (), 0x10)
Field (TCBA, ByteAcc, NoLock, Preserve)
{
Offset (0x04),
, 9,
CPSC, 1
}
}
Problem with the current approach is that it blocks all I/O port access
and because this system has touchpad connected to the SMBus controller
after first AML access (happens during suspend/resume cycle) the
touchpad fails to work anymore.
Fix this so that we allow ACPI AML I/O port access if it does not touch
the region reserved for the SMBus.
Fixes: 7ae81952cda ("i2c: i801: Allow ACPI SystemIO OpRegion to conflict with PCI BAR")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200737
Reported-by: Yussuf Khalil <dev@pp3345.net>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This can be dropped with commit 771c035372
("deprecate the '__deprecated' attribute warnings entirely and for good")
now in upstream.
And we got rid of the last __deprecated use, too.
Signed-off-by: Sedat Dilek <sedat.dilek@credativ.de>
[wsa: shortened commit message to reflect the current situation]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The old @sunsite.dk address is no longer active, so update the references.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There aren't any users left. Remove this callback from the 2.4 times.
Phew, finally, that took years to reach...
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
- the core has now a lockless variant of i2c_smbus_xfer. Some open
coded versions of this got removed in drivers. This also enables
proper SCCB support in regmap.
- locking got a more precise naming. i2c_{un}lock_adapter() had to go,
and we know use i2c_lock_bus() consistently with flags like
I2C_LOCK_ROOT_ADAPTER and I2C_LOCK_SEGMENT to avoid ambiguity.
- the gpio fault injector got a new delicate testcase
- the bus recovery procedure got fixed to handle the new testcase
correctly
- a new quirk flag for controllers not able to handle zero length
messages together with driver updates to use it
- new drivers: FSI bus attached I2C masters, GENI I2C controller, Owl
family S900
- and a good set of driver improvements and bugfixes
* 'i2c/for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (77 commits)
i2c: rcar: implement STOP and REP_START according to docs
i2c: rcar: refactor private flags
i2c: core: ACPI: Make acpi_gsb_i2c_read_bytes() check i2c_transfer return value
i2c: core: ACPI: Properly set status byte to 0 for multi-byte writes
dt-bindings: i2c: rcar: Add r8a774a1 support
dt-bindings: i2c: sh_mobile: Add r8a774a1 support
i2c: imx: Simplify stopped state tracking
i2c: imx: Fix race condition in dma read
i2c: pasemi: remove hardcoded bus numbers on smbus
i2c: designware: Add SPDX license tag
i2c: designware: Convert to use struct i2c_timings
i2c: core: Parse SDA hold time from firmware
i2c: designware-pcidrv: Mark expected switch fall-through
i2c: amd8111: Mark expected switch fall-through
i2c: sh_mobile: use core to detect 'no zero length read' quirk
i2c: xlr: use core to detect 'no zero length' quirk
i2c: rcar: use core to detect 'no zero length' quirk
i2c: stu300: use core to detect 'no zero length' quirk
i2c: pmcmsp: use core to detect 'no zero length' quirk
i2c: mxs: use core to detect 'no zero length' quirk
...
When doing a REP_START after a read message, the driver used to trigger
a STOP first which would then be overwritten by REP_START. This was the
only stable method found when doing the last refactoring. However, this
was not in accordance with the documentation.
After research from our BSP team and myself, we now can implement a
version which works and is according to the documentation. The new
approach ensures the ICMCR register is only changed when really needed.
Tested on a R-Car Gen2 (H2) and Gen3 with DMA (M3N).
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use BIT macro to avoid shift-31-problem, indent a little more and use
GENMASK to make it easier to add new flags.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently acpi_gsb_i2c_read_bytes() directly returns i2c_transfer's return
value. i2c_transfer returns a value < 0 on error and 2 (for 2 successfully
executed transfers) on success. But the ACPI code expects 0 on success, so
currently acpi_gsb_i2c_read_bytes()'s caller does:
if (status > 0)
status = 0;
This commit makes acpi_gsb_i2c_read_bytes() return a value which can be
directly consumed by the ACPI code, mirroring acpi_gsb_i2c_write_bytes(),
this commit also makes acpi_gsb_i2c_read_bytes() explitcly check that
i2c_transfer returns 2, rather then accepting any value > 0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
acpi_gsb_i2c_write_bytes() returns i2c_transfer()'s return value, which
is the number of transfers executed on success, so 1.
The ACPI code expects us to store 0 in gsb->status for success, not 1.
Specifically this breaks the following code in the Thinkpad 8 DSDT:
ECWR = I2CW = ECWR /* \_SB_.I2C1.BAT0.ECWR */
If ((ECST == Zero))
{
ECRD = I2CR /* \_SB_.I2C1.I2CR */
}
Before this commit we set ECST to 1, causing the read to never happen
breaking battery monitoring on the Thinkpad 8.
This commit makes acpi_gsb_i2c_write_bytes() return 0 when i2c_transfer()
returns 1, so the single write transfer completed successfully, and
makes it return -EIO on for other (unexpected) return values >= 0.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Always update the stopped state when busy status have been checked.
This is identical to what was done before, with the exception of error
handling.
Without this change, some errors cause the stopped state to be left in
incorrect state in i2c_imx_stop(), i2c_imx_dma_read(), i2c_imx_read() and
i2c_imx_xfer().
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This fixes a race condition, where the DMAEN bit ends up being set after
I2C slave has transmitted a byte following the dummy read. When that
happens, an interrupt is generated instead, and no DMA request is generated
to kickstart the DMA read, and a timeout happens after DMA_TIMEOUT (1 sec).
Fixed by setting the DMAEN bit before the dummy read.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
The pasemi smbus controller uses PCI_FUNC(dev->devfn) to define which
number bus to attach to, however this fails when something else is
probed first, for example an ATI Radeon graphics card will claim 9 or
10 busses, including the ones the pasemi wants.
Patch the driver to call i2c_add_adapter rather than
i2c_add_numbered_adapter.
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Replace short statement in comment with proper SPDX license tag.
Note, for i2c-desingware-slave.c the identifier is chosen
in accordance with MODULE_LICENSE() macro since it is visible to user.
Another point to this choice is that the header seems to be copy'n'paste
from the other file of this very driver.
Acked-by: Luis Oliveira <Luis.Oliveira@synopsys.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Several small new features for regmap this time around:
- Support for SCCB, an I2C variant used on some media cards. This has
also pulled in an I2C commit from Peter Rosin as a dependency.
- Addition of an API for reading repeatedly from registers where the
address doesn't automatically increment like some ADC outputs or GPIO
status registers.
- Support for bulk I/O on Slimbus.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAltxUxYTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0B26B/9A/Q9P+92i0LZ2ecO3QltvPeIP46jR
gnS3WEmgMk/yIWR9wusF3Ju4gfTZ4L5DEkl+5iooqlg54e3c8l3OdDIsRXXiLtIK
+BOU9xW4u4sdmGjuXqkkGCWgz75r/Em07Z4y3pB5kl/KHGtQPOrrvS8/33ETjhKC
tg/SC8bdJ6ZSC2J1lVYA+IolNfVt0rvjY3TdXwm0qel9SmQIqrL8xilj/JV8Hmhg
6PSH9PIoIkSRgvqp1N0IOysVcDcwgjAEyg3eeH+L2S0y/YMPY88ndf7d8mpWdkzQ
KGEUxgB+qWBHMjRKTgu4sqal1KZxCPghxO5kRn4UBaZsxFDdnXbtDcRQ
=e1ml
-----END PGP SIGNATURE-----
Merge tag 'regmap-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"Several small new features for regmap this time around:
- Support for SCCB, an I2C variant used on some media cards. This has
also pulled in an I2C commit from Peter Rosin as a dependency.
- Addition of an API for reading repeatedly from registers where the
address doesn't automatically increment like some ADC outputs or
GPIO status registers.
- Support for bulk I/O on Slimbus"
* tag 'regmap-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Add regmap_noinc_read API
regmap: sccb: fix typo and sort headers alphabetically
i2c: smbus: add unlocked __i2c_smbus_xfer variant
regmap: add SCCB support
regmap: slimbus: add support to multi read/write
During ipmi stress tests we see occasional failure of transactions
at the boot time. This happens in the case of a I2C_M_RECV_LEN
transactions, when the read transfer completes (with the initial
read length of 34) before the driver gets a chance to handle interrupts.
The current driver code expects at least 2 interrupts for I2C_M_RECV_LEN
transactions. The length is updated during the first interrupt, and the
buffer contents are only copied during subsequent interrupts. In case of
just one interrupt, we will complete the transaction without copying
out the bytes from RX fifo.
Update the code to drain the RX fifo after the length update,
so that the transaction completes correctly in all cases.
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Instead of using custom variables and parser, convert the driver to use
the ones provided by I2C core.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There are two drivers already using the SDA hold time setting.
It might be more in the future, thus, make I2C core to parse the setting
for us if provided by firmware.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
And don't reimplement in the driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
And don't reimplement in the driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
And don't reimplement in the driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
And don't reimplement in the driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some adapters do not support a message length of 0. Add this as a quirk
so drivers don't have to open code it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This bus driver supports the GENI based i2c hardware controller in the
Qualcomm SOCs. The Qualcomm Generic Interface (GENI) is a programmable
module supporting a wide range of serial interfaces including I2C. The
driver supports FIFO mode and DMA mode of transfer and switches modes
dynamically depending on the size of the transfer.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Signed-off-by: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
[wsa: squashed the MAINTAINER addition and a RPM fix by Evan Green]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull locking fixes from Ingo Molnar:
"A paravirt UP-patching fix, and an I2C MUX driver lockdep warning fix"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/pvqspinlock/x86: Use LOCK_PREFIX in __pv_queued_spin_unlock() assembly code
i2c/mux, locking/core: Annotate the nested rt_mutex usage
locking/rtmutex: Allow specifying a subclass for nested locking
This creates a struct device *dev helper variable in probe()
which IMO makes the code less cluttered and easier to read.
Also rename the of_node veriable to the common shortform "np"
(node pointer).
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[peda: slightly edited commit message and removed some surplus newlines]
Signed-off-by: Peter Rosin <peda@axentia.se>
If an i2c topology has instances of nested muxes, then a lockdep splat
is produced when when i2c_parent_lock_bus() is called. Here is an
example:
============================================
WARNING: possible recursive locking detected
--------------------------------------------
insmod/68159 is trying to acquire lock:
(i2c_register_adapter#2){+.+.}, at: i2c_parent_lock_bus+0x32/0x50 [i2c_mux]
but task is already holding lock:
(i2c_register_adapter#2){+.+.}, at: i2c_parent_lock_bus+0x32/0x50 [i2c_mux]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(i2c_register_adapter#2);
lock(i2c_register_adapter#2);
*** DEADLOCK ***
May be due to missing lock nesting notation
1 lock held by insmod/68159:
#0: (i2c_register_adapter#2){+.+.}, at: i2c_parent_lock_bus+0x32/0x50 [i2c_mux]
stack backtrace:
CPU: 13 PID: 68159 Comm: insmod Tainted: G O
Call Trace:
dump_stack+0x67/0x98
__lock_acquire+0x162e/0x1780
lock_acquire+0xba/0x200
rt_mutex_lock+0x44/0x60
i2c_parent_lock_bus+0x32/0x50 [i2c_mux]
i2c_parent_lock_bus+0x3e/0x50 [i2c_mux]
i2c_smbus_xfer+0xf0/0x700
i2c_smbus_read_byte+0x42/0x70
my2c_init+0xa2/0x1000 [my2c]
do_one_initcall+0x51/0x192
do_init_module+0x62/0x216
load_module+0x20f9/0x2b50
SYSC_init_module+0x19a/0x1c0
SyS_init_module+0xe/0x10
do_syscall_64+0x6c/0x1a0
entry_SYSCALL_64_after_hwframe+0x42/0xb7
Reported-by: John Sperbeck <jsperbeck@google.com>
Tested-by: John Sperbeck <jsperbeck@google.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Deepa Dinamani <deepadinamani@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Chang <dpf@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Link: http://lkml.kernel.org/r/20180720083914.1950-3-peda@axentia.se
Signed-off-by: Ingo Molnar <mingo@kernel.org>
I2C is open drain, so request the GPIO accordingly, even if pinmux did
set it up correctly for in-kernel users in this case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On Gen3, we can only do RXDMA once per transfer reliably. For that, we
must reset the device, then we can have RXDMA once. This patch
implements this. When there is no reset controller or the reset fails,
RXDMA will be blocked completely. Otherwise, it will be disabled after
the first RXDMA transfer. Based on a commit from the BSP by Hiromitsu
Yamasaki, yet completely refactored to handle multiple read messages
within one transfer.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
On Gen3, we can only do RXDMA once per transfer reliably. For that, we
must reset the device, then we can have RXDMA once. This patch
implements this. When there is no reset controller or the reset fails,
RXDMA will be blocked completely. Otherwise, it will be disabled after
the first RXDMA transfer. Based on a commit from the BSP by Hiromitsu
Yamasaki, yet completely refactored to handle multiple read messages
within one transfer.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make sure to call reinit_completion() before dma is started to avoid race
condition where reinit_completion() is called after complete() and before
wait_for_completion_timeout().
Signed-off-by: Esben Haabendal <eha@deif.com>
Fixes: ce1a78840f ("i2c: imx: add DMA support for freescale i2c driver")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
If CLKH is set to 0 I2C clock is not generated at all, so avoid this value
and stretch the clock in this case.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adjusts spinlock scope to make it wrap the whole irq
handler using a single lock/unlock which covers both master and
slave handlers.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch changes the order of enum aspeed_i2c_master_state and
enum aspeed_i2c_slave_state defines to make their initial value to
ASPEED_I2C_MASTER_INACTIVE and ASPEED_I2C_SLAVE_STOP respectively.
In case of multi-master use, if a slave data comes ahead of the
first master xfer, master_state starts from an invalid state so
this change fixes the issue.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There are some log printing without a newline character. This
patch adds the missing newline characters.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver supports multiple hardware variants of Exynos I2C controller
which differ in FIFO depth, handling of interrupts and bus recovery in
HSI2C_MASTER_ST_LOSE state.
The difference in variant was a single bit set for Exynos7 variants and
implicit lack of this bit for other variants.
Make each variant explicit which also fixes the GCC warning about
documentation:
drivers/i2c/busses/i2c-exynos5.c:223: warning: Function parameter or member 'hw' not described in 'exynos_hsi2c_variant'
No change in functionality.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When we initialize the pins, make sure it looks like STOP by dividing
the delay into halves. It shouldn't matter because SDA is expected to be
held low by a device, but for super-safety, let's do it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Bus recovery should reset the bus with the standard i2c recovery
procedure. Populate the necessary fields so that the standard procedure
can perform the reset.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since there are many ports per master, each with it's own adapter and
chardev, we need some locking to prevent transfers from changing the
master state while other transfers are in progress.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Execute I2C transfers from the FSI-attached I2C master. Use polling
instead of interrupts as we have no hardware IRQ over FSI.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add abort procedure for failed transfers. Add engine reset procedure
that is executed during the abort to recover from various fault
conditions.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add and initialize I2C adapters for each port on the FSI-attached I2C
master. Ports for each master are defined in the devicetree.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add register definitions for FSI-attached I2C master and functions to
access those registers over FSI. Add an FSI driver so that our I2C bus
is probed up during an FSI scan.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Removes all locking from i2c_smbus_xfer and renames it to __i2c_smbus_xfer,
then adds a new i2c_smbus_xfer function that simply grabs the lock while
calling the unlocked variant.
This is not perfectly equivalent, since i2c_smbus_xfer was callable from
atomic/irq context if you happened to end up emulating SMBus with an I2C
transfer, and that is no longer the case with this patch. It is unknown
(to me) if anything depends on that quirk, but it seems fragile enough to
simply break those cases and require them to call i2c_transfer directly
instead.
While at it, for consistency rename the 2nd to last argument (size) of
the i2c_smbus_xfer declaration to protocol and remove the surplus extern
marker.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
While refactoring the routine before, it occurred to me that this will
make the code much easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
To break out of recovery as early as possible, feed back the bus_free
logic state.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some IP cores have an internal 'bus free' logic which may be more
advanced than just checking if SDA is high. Add a separate callback to
get this status. Filling it is optional.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
After exiting the while loop, we checked if recovery was successful and
sent a STOP to the clients. Meanwhile however, we send a STOP after
every pulse, so it is not needed after the loop. If we move the check
for a free bus to the end of the while loop, we can shorten and simplify
the logic. It is still ensured that at least one STOP will be sent to
the wire even if SDA was not stuck low.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For bus recovery, we either need to bail out early if we can read SDA or
we need to send STOP after every pulse. Otherwise recovery might be
misinterpreted as an unwanted write. So, require one of those SDA
handling functions to avoid this problem.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c fixes from Wolfram Sang:
- I2C core bugfix regarding bus recovery
- driver bugfix for the tegra driver
- typo correction
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: recovery: if possible send STOP with recovery pulses
i2c: tegra: Fix NACK error handling
i2c: stu300: use non-archaic spelling of failes
The i2c_lock_adapter name is ambiguous since it is unclear if it
refers to the root adapter or the adapter you name in the argument.
The natural interpretation is the adapter you name in the argument,
but there are historical reasons for that not being the case; it
in fact locks the root adapter. Just remove the function and force
users to spell out the I2C_LOCK_ROOT_ADAPTER name to indicate what
is really going on. Also remove i2c_unlock_adapter, of course.
This patch was generated with
git grep -l 'i2c_\(un\)\?lock_adapter' \
| xargs sed -i 's/i2c_\(un\)\?lock_adapter(\([^)]*\))/'\
'i2c_\1lock_bus(\2, I2C_LOCK_ROOT_ADAPTER)/g'
followed by white-space touch-up.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Locking the root adapter for __i2c_transfer will deadlock if the
device sits behind a mux-locked I2C mux. Switch to the finer-grained
i2c_lock_bus with the I2C_LOCK_SEGMENT flag. If the device does not
sit behind a mux-locked mux, the two locking variants are equivalent.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C clients may misunderstand recovery pulses if they can't read SDA to
bail out early. In the worst case, as a write operation. To avoid that
and if we can write SDA, try to send STOP to avoid the
misinterpretation.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
On Tegra30 Cardhu the PCA9546 I2C mux is not ACK'ing I2C commands on
resume from suspend (which is caused by the reset signal for the I2C
mux not being configured correctl). However, this NACK is causing the
Tegra30 to hang on resuming from suspend which is not expected as we
detect NACKs and handle them. The hang observed appears to occur when
resetting the I2C controller to recover from the NACK.
Commit 77821b4678 ("i2c: tegra: proper handling of error cases") added
additional error handling for some error cases including NACK, however,
it appears that this change conflicts with an early fix by commit
f70893d083 ("i2c: tegra: Add delay before resetting the controller
after NACK"). After commit 77821b4678 was made we now disable 'packet
mode' before the delay from commit f70893d083 happens. Testing shows
that moving the delay to before disabling 'packet mode' fixes the hang
observed on Tegra30. The delay was added to give the I2C controller
chance to send a stop condition and so it makes sense to move this to
before we disable packet mode. Please note that packet mode is always
enabled for Tegra.
Fixes: 77821b4678 ("i2c: tegra: proper handling of error cases")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@vger.kernel.org
Intel Ice Lake has the same SMBus host controller than Intel Cannon
Lake. Add the PCI ID to the drivers list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[jarkko.nikula@linux.intel.com: Add entries to Documentation and Kconfig]
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make list of supported chipsets a little bit shorter by consolidating
names that belong to the same family.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In order to support advanced features, the I2C FIFO interface was
changed in the version of the Tegra I2C controller found in Tegra194.
The changes are backwards incompatible, so the driver needs to be
programmed in a slightly different way on new chips.
Add support for MST FIFO programming and add an OF match entry for
Tegra194. At the same time, mark all prior generations of this
controller as not having the MST FIFO interface.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add another injector for an incomplete transfer. As mentioned in the
docs, this one is important to check bus recovery algorithms with it.
Otherwise random data may be sent to devices!
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make the incomplete_transfer routine reusable, so we can add other test
cases with different patterns later. Prepare the docs for that, too.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Trivial added debug print for dev->clk_freq doesn't necessarily tell the
actual bus speed or mode the controller is operating. For instance it
may indicate 1 MHz Fast Mode Plus or 3.4 MHz High Speed but driver ends up
using 400 kHz Fast Mode due missing timing parameters or missing support
from HW.
Add a debug print that prints the bus speed based on the validated speed
that gets programmed into a HW.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
SDA hold time is an important timing parameter and often reason for
arbitration lost errors if not set to a correct value. Add a debug print
for it in order to see what value gets programmed to a HW.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Mixed timing parameter validation, calculation and their debug prints
with HW initialization in i2c_dw_init_master() and i2c_dw_init_slave()
as been bothering me some time.
It makes function a little bit unclear to follow, doesn't show what steps
are needed to do only once during probe and what are needed whenever HW
needs to be reinitialized. Also those debug prints show information that
doesn't change runtime and thus are also needlessly printed multiple times
whenever HW is reinitialized.
Thus let the i2c_dw_init_master() and i2c_dw_init_slave() to do only HW
initialization and move out one time parameter setting and debug prints
to separate functions which are called only during probe.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
SDA hold time configuration is common to both master and slave code. It
is also something that can be done once during probe and do only
register write when HW needs to be reinitialized.
Remove duplication and move SDA hold time configuration to common code.
It will be called from slave probe and for master code from a new
i2c_dw_set_timings_master() to where we will populate more probe time
timing parameter setting.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is rather readability update than micro-optimization, or if not
optimization at all. We take the input clock rate to a variable and pass
that to SCL timing parameter calculation functions.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It looks ___constant_swab32 is an internal byte swap detail. Switch to
swap32() and include header file for it explicitly. Now it comes
implicitly via linux/i2c.h include.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move register access detection out from master and slave HW
initialization code to common code. Motivation for this is to have
register access configured before HW initialization and remove
duplicated code.
This allows to do further separation between probe time initialization
and runtime reinitialization code.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 43df43e6ba ("i2c: designware: Don't set SCL timings and speed
mode when in slave mode") made variable comp_param1 needless in
i2c_dw_init_slave(). Remove it now.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Calling the __i2c_smbus_xfer wrapper in __i2c_mux_smbus_xfer provides
retries and thus makes the parent-locked case consistent with the both
mux-locked (i2c_mux_smbus_xfer) and the I2C transfer cases.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This simplifies the code, and you get retries for free if the adapter
does not support ->master_xfer.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This simplifies the code, and you get retries for free if the adapter
does not support ->master_xfer.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This simplifies the code, and you get retries for free if the adapter
does not support ->master_xfer.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Michael Shych <michaelsh@mellanox.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
