This patch adds a per-pci-device subdirectory in sysfs called:
/sys/bus/pci/devices/<device>/msi_irqs
This sub-directory exports the set of msi vectors allocated by a given
pci device, by creating a numbered sub-directory for each vector beneath
msi_irqs. For each vector various attributes can be exported.
Currently the only attribute is called mode, which tracks the
operational mode of that vector (msi vs. msix)
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The ats and sroiv members of 'struct pci_dev' are required
for the ATS code already, even without IOV support compiled
in. So depend on ATS here. This is fine with PCI_IOV too
because it selects PCI_ATS. Also the prototypes for ATS
need to be available for PCI_ATS.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'next-rebase' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci:
PCI: Clean-up MPS debug output
pci: Clamp pcie_set_readrq() when using "performance" settings
PCI: enable MPS "performance" setting to properly handle bridge MPS
PCI: Workaround for Intel MPS errata
PCI: Add support for PASID capability
PCI: Add implementation for PRI capability
PCI: Export ATS functions to modules
PCI: Move ATS implementation into own file
PCI / PM: Remove unnecessary error variable from acpi_dev_run_wake()
PCI hotplug: acpiphp: Prevent deadlock on PCI-to-PCI bridge remove
PCI / PM: Extend PME polling to all PCI devices
PCI quirk: mmc: Always check for lower base frequency quirk for Ricoh 1180:e823
PCI: Make pci_setup_bridge() non-static for use by arch code
x86: constify PCI raw ops structures
PCI: Add quirk for known incorrect MPSS
PCI: Add Solarflare vendor ID and SFC4000 device IDs
The land of PCI power management is a land of sorrow and ugliness,
especially in the area of signaling events by devices. There are
devices that set their PME Status bits, but don't really bother
to send a PME message or assert PME#. There are hardware vendors
who don't connect PME# lines to the system core logic (they know
who they are). There are PCI Express Root Ports that don't bother
to trigger interrupts when they receive PME messages from the devices
below. There are ACPI BIOSes that forget to provide _PRW methods for
devices capable of signaling wakeup. Finally, there are BIOSes that
do provide _PRW methods for such devices, but then don't bother to
call Notify() for those devices from the corresponding _Lxx/_Exx
GPE-handling methods. In all of these cases the kernel doesn't have
a chance to receive a proper notification that it should wake up a
device, so devices stay in low-power states forever. Worse yet, in
some cases they continuously send PME Messages that are silently
ignored, because the kernel simply doesn't know that it should clear
the device's PME Status bit.
This problem was first observed for "parallel" (non-Express) PCI
devices on add-on cards and Matthew Garrett addressed it by adding
code that polls PME Status bits of such devices, if they are enabled
to signal PME, to the kernel. Recently, however, it has turned out
that PCI Express devices are also affected by this issue and that it
is not limited to add-on devices, so it seems necessary to extend
the PME polling to all PCI devices, including PCI Express and planar
ones. Still, it would be wasteful to poll the PME Status bits of
devices that are known to receive proper PME notifications, so make
the kernel (1) poll the PME Status bits of all PCI and PCIe devices
enabled to signal PME and (2) disable the PME Status polling for
devices for which correct PME notifications are received.
Tested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The "powernv" platform of the powerpc architecture needs to assign PCI
resources using a specific algorithm to fit some HW constraints of
the IBM "IODA" architecture (related to the ability to create error
handling domains that encompass specific segments of MMIO space).
For doing so, it wants to call pci_setup_bridge() from architecture
specific resource management in order to configure bridges after all
resources have been assigned. So make it non-static.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add the ability to disable PCI-E MPS turning and using the BIOS
configured MPS defaults. Due to the number of issues recently
discovered on some x86 chipsets, make this the default behavior.
Also, add the option for peer to peer DMA MPS configuration. Peer to
peer DMA is outside the scope of this patch, but MPS configuration could
prevent it from working by having the MPS on one root port different
than the MPS on another. To work around this, simply make the system
wide MPS the smallest possible value (128B).
Signed-off-by: Jon Mason <mason@myri.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Device drivers that create and destroy SR-IOV virtual functions via
calls to pci_enable_sriov() and pci_disable_sriov can cause catastrophic
failures if they attempt to destroy VFs while they are assigned to
guest virtual machines. By adding a flag for use by the KVM module
to indicate that a device is assigned a device driver can check that
flag and avoid destroying VFs while they are assigned and avoid system
failures.
CC: Ian Campbell <ijc@hellion.org.uk>
CC: Konrad Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently pci-bridges are allocated enough resources to satisfy their immediate
requirements. Any additional resource-requests fail if additional free space,
contiguous to the one already allocated, is not available. This behavior is not
reasonable since sufficient contiguous resources, that can satisfy the request,
are available at a different location.
This patch provides the ability to expand and relocate a allocated resource.
v2: Changelog: Fixed size calculation in pci_reassign_resource()
v3: Changelog : Split this patch. The resource.c changes are already
upstream. All the pci driver changes are in here.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
On a given PCI-E fabric, each device, bridge, and root port can have a
different PCI-E maximum payload size. There is a sizable performance
boost for having the largest possible maximum payload size on each PCI-E
device. However, if improperly configured, fatal bus errors can occur.
Thus, it is important to ensure that PCI-E payloads sends by a device
are never larger than the MPS setting of all devices on the way to the
destination.
This can be achieved two ways:
- A conservative approach is to use the smallest common denominator of
the entire tree below a root complex for every device on that fabric.
This means for example that having a 128 bytes MPS USB controller on one
leg of a switch will dramatically reduce performances of a video card or
10GE adapter on another leg of that same switch.
It also means that any hierarchy supporting hotplug slots (including
expresscard or thunderbolt I suppose, dbl check that) will have to be
entirely clamped to 128 bytes since we cannot predict what will be
plugged into those slots, and we cannot change the MPS on a "live"
system.
- A more optimal way is possible, if it falls within a couple of
constraints:
* The top-level host bridge will never generate packets larger than the
smallest TLP (or if it can be controlled independently from its MPS at
least)
* The device will never generate packets larger than MPS (which can be
configured via MRRS)
* No support of direct PCI-E <-> PCI-E transfers between devices without
some additional code to specifically deal with that case
Then we can use an approach that basically ignores downstream requests
and focuses exclusively on upstream requests. In that case, all we need
to care about is that a device MPS is no larger than its parent MPS,
which allows us to keep all switches/bridges to the max MPS supported by
their parent and eventually the PHB.
In this case, your USB controller would no longer "starve" your 10GE
Ethernet and your hotplug slots won't affect your global MPS.
Additionally, the hotplugged devices themselves can be configured to a
larger MPS up to the value configured in the hotplug bridge.
To choose between the two available options, two PCI kernel boot args
have been added to the PCI calls. "pcie_bus_safe" will provide the
former behavior, while "pcie_bus_perf" will perform the latter behavior.
By default, the latter behavior is used.
NOTE: due to the location of the enablement, each arch will need to add
calls to this function. This patch only enables x86.
This patch includes a number of changes recommended by Benjamin
Herrenschmidt.
Tested-by: Jordan_Hargrave@dell.com
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: remove printks about disabled bridge windows
PCI: fold pci_calc_resource_flags() into decode_bar()
PCI: treat mem BAR type "11" (reserved) as 32-bit, not 64-bit, BAR
PCI: correct pcie_set_readrq write size
PCI: pciehp: change wait time for valid configuration access
x86/PCI: Preserve existing pci=bfsort whitelist for Dell systems
PCI: ARI is a PCIe v2 feature
x86/PCI: quirks: Use pci_dev->revision
PCI: Make the struct pci_dev * argument of pci_fixup_irqs const.
PCI hotplug: cpqphp: use pci_dev->vendor
PCI hotplug: cpqphp: use pci_dev->subsystem_{vendor|device}
x86/PCI: config space accessor functions should not ignore the segment argument
PCI: Assign values to 'pci_obff_signal_type' enumeration constants
x86/PCI: reduce severity of host bridge window conflict warnings
PCI: enumerate the PCI device only removed out PCI hieratchy of OS when re-scanning PCI
PCI: PCIe AER: add aer_recover_queue
x86/PCI: select direct access mode for mmconfig option
PCI hotplug: Rename is_ejectable which also exists in dock.c
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
iommu/core: Fix build with INTR_REMAP=y && CONFIG_DMAR=n
iommu/amd: Don't use MSI address range for DMA addresses
iommu/amd: Move missing parts to drivers/iommu
iommu: Move iommu Kconfig entries to submenu
x86/ia64: intel-iommu: move to drivers/iommu/
x86: amd_iommu: move to drivers/iommu/
msm: iommu: move to drivers/iommu/
drivers: iommu: move to a dedicated folder
x86/amd-iommu: Store device alias as dev_data pointer
x86/amd-iommu: Search for existind dev_data before allocting a new one
x86/amd-iommu: Allow dev_data->alias to be NULL
x86/amd-iommu: Use only dev_data in low-level domain attach/detach functions
x86/amd-iommu: Use only dev_data for dte and iotlb flushing routines
x86/amd-iommu: Store ATS state in dev_data
x86/amd-iommu: Store devid in dev_data
x86/amd-iommu: Introduce global dev_data_list
x86/amd-iommu: Remove redundant device_flush_dte() calls
iommu-api: Add missing header file
Fix up trivial conflicts (independent additions close to each other) in
drivers/Makefile and include/linux/pci.h
Aside of the usual motivation for constification, this function has a
history of being abused a hook for interrupt and other fixups so I turned
this function const ages ago in the MIPS code but it should be done
treewide.
Due to function pointer passing in varous places a few other functions
had to be constified as well.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To: Anton Vorontsov <avorontsov@mvista.com>
To: Chris Metcalf <cmetcalf@tilera.com>
To: Colin Cross <ccross@android.com>
Acked-by: "David S. Miller" <davem@davemloft.net>
To: Eric Miao <eric.y.miao@gmail.com>
To: Erik Gilling <konkers@android.com>
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
To: "H. Peter Anvin" <hpa@zytor.com>
To: Imre Kaloz <kaloz@openwrt.org>
To: Ingo Molnar <mingo@redhat.com>
To: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
To: Jesse Barnes <jbarnes@virtuousgeek.org>
To: Krzysztof Halasa <khc@pm.waw.pl>
To: Lennert Buytenhek <kernel@wantstofly.org>
To: Matt Turner <mattst88@gmail.com>
To: Nicolas Pitre <nico@fluxnic.net>
To: Olof Johansson <olof@lixom.net>
Acked-by: Paul Mundt <lethal@linux-sh.org>
To: Richard Henderson <rth@twiddle.net>
To: Russell King <linux@arm.linux.org.uk>
To: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-alpha@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-pci@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: sparclinux@vger.kernel.org
Cc: x86@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
'pci_obff_signal_type' is passed between drivers and the kernel API.
This patch explicitly assigns values to the enumeration type's constants
which aids in detecting any future changes or additions that would break
the kernel's ABI.
No functional change.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This should ease finding similarities with different platforms,
with the intention of solving problems once in a generic framework
which everyone can use.
Note: to move intel-iommu.c, the declaration of pci_find_upstream_pcie_bridge()
has to move from drivers/pci/pci.h to include/linux/pci.h. This is handled
in this patch, too.
As suggested, also drop DMAR's EXPERIMENTAL tag while we're at it.
Compile-tested on x86_64.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The generic code always get the device-node in the right place now
so a single implementation will work for all archs
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Michal Simek <monstr@monstr.eu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
All archs do more or less the same thing now, move it into
a single generic place.
I chose pci.h rather than of_pci.h to avoid having to change
all call-sites to include the later.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Michal Simek <monstr@monstr.eu>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
powerpc has two different ways of matching PCI devices to their
corresponding OF node (if any) for historical reasons. The ppc64 one
does a scan looking for matching bus/dev/fn, while the ppc32 one does a
scan looking only for matching dev/fn on each level in order to be
agnostic to busses being renumbered (which Linux does on some
platforms).
This removes both and instead moves the matching code to the PCI core
itself. It's the most logical place to do it: when a pci_dev is created,
we know the parent and thus can do a single level scan for the matching
device_node (if any).
The benefit is that all archs now get the matching for free. There's one
hook the arch might want to provide to match a PHB bus to its device
node. A default weak implementation is provided that looks for the
parent device device node, but it's not entirely reliable on powerpc for
various reasons so powerpc provides its own.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Michal Simek <monstr@monstr.eu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (169 commits)
drivers/gpu/drm/radeon/atom.c: fix warning
drm/radeon/kms: bump kms version number
drm/radeon/kms: properly set num banks for fusion asics
drm/radeon/kms/atom: move dig phy init out of modesetting
drm/radeon/kms/cayman: fix typo in register mask
drm/radeon/kms: fix typo in spread spectrum code
drm/radeon/kms: fix tile_config value reported to userspace on cayman.
drm/radeon/kms: fix incorrect comparison in cayman setup code.
drm/radeon/kms: add wait idle ioctl for eg->cayman
drm/radeon/cayman: setup hdp to invalidate and flush when asked
drm/radeon/evergreen/btc/fusion: setup hdp to invalidate and flush when asked
agp/uninorth: Fix lockups with radeon KMS and >1x.
drm/radeon/kms: the SS_Id field in the LCD table if for LVDS only
drm/radeon/kms: properly set the CLK_REF bit for DCE3 devices
drm/radeon/kms: fixup eDP connector handling
drm/radeon/kms: bail early for eDP in hotplug callback
drm/radeon/kms: simplify hotplug handler logic
drm/radeon/kms: rewrite DP handling
drm/radeon/kms/atom: add support for setting DP panel mode
drm/radeon/kms: atombios.h updates for DP panel mode
...
For KVM device assignment, we'd like to save off the state of a device
prior to passing it to the guest and restore it later. We also want
to allow pci_reset_funciton() to be called while the device is owned
by the guest. This however overwrites and invalidates the struct pci_dev
buffers, so we can't just manually call save and restore. Add generic
interfaces for the saved state to be stored and reloaded back into
struct pci_dev at a later time.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This will allow us to store and load it later.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Latency tolerance reporting allows devices to send messages to the root
complex indicating their latency tolerance for snooped & unsnooped
memory transactions. Add support for enabling & disabling this
feature, along with a routine to set the max latencies a device should
send upstream.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
OBFF (optimized buffer flush/fill), where supported, can help improve
energy efficiency by giving devices information about when interrupts
and other activity will have a reduced power impact. It requires
support from both the device and system (i.e. not only does the device
need to respond to OBFF messages, but the platform must be capable of
generating and routing them to the end point).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add support to allow drivers to enable/disable ID-based ordering. Where
supported, ID-based ordering can significantly improve the latency of
individual requests by preventing them from queueing up behind unrelated
traffic.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
So in a lot of modern systems, a GPU will always be below a parent bridge that won't share with any other GPUs. This means VGA arbitration on those GPUs can be controlled by using the bridge routing instead of io/mem decodes.
The problem is locating which GPUs share which upstream bridges. This patch attempts to identify all the GPUs which can be controlled via bridges, and ones that can't. This patch endeavours to work out the bridge sharing semantics.
When disabling GPUs via a bridge, it doesn't do irq callbacks or touch the io/mem decodes for the gpu.
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to distinguish the situation in which ASPM support is
disabled from the command line or through .config from the situation
in which it is disabled, because the hardware or BIOS can't handle
it. In the former case we should not report ASPM support to the BIOS
through ACPI _OSC, but in the latter case we should do that.
Introduce pcie_aspm_support_enabled() that can be used by
acpi_pci_root_add() to determine whether or not it should report ASPM
support to the BIOS through _OSC.
Cc: stable@kernel.org
References: https://bugzilla.kernel.org/show_bug.cgi?id=29722
References: https://bugzilla.kernel.org/show_bug.cgi?id=20232
Reported-and-tested-by: Ortwin Glück <odi@odi.ch>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: label: remove #include of ACPI header to avoid warnings
PCI: label: Fix compilation error when CONFIG_ACPI is unset
PCI: pre-allocate additional resources to devices only after successful allocation of essential resources.
PCI: introduce reset_resource()
PCI: data structure agnostic free list function
PCI: refactor io size calculation code
PCI: do not create quirk I/O regions below PCIBIOS_MIN_IO for ICH
PCI hotplug: acpiphp: set current_state to D0 in register_slot
PCI: Export ACPI _DSM provided firmware instance number and string name to sysfs
PCI: add more checking to ICH region quirks
PCI: aer-inject: Override PCIe AER Mask Registers
PCI: fix tlan build when CONFIG_PCI is not enabled
PCI: remove quirk for pre-production systems
PCI: Avoid potential NULL pointer dereference in pci_scan_bridge
PCI/lpc: irq and pci_ids patch for Intel DH89xxCC DeviceIDs
PCI: sysfs: Fix failure path for addition of "vpd" attribute
This patch adds code to verify the checksum stored in the "RV" info
keyword of the RODATA VPD section.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_PCI is not enabled, tlan.c has a build error:
drivers/net/tlan.c:503: error: implicit declaration of function 'pci_wake_from_d3'
so add an inline function stub for this function to pci.h when
PCI is not enabled, similar to other stubbed PCI functions.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The compilation of drivers/acpi/pci_root.c fails if
CONFIG_PCIEPORTBUS is unset. Fix the problem.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After recent changes related to wakeup events pm_wakeup_event()
automatically checks if the given device is configured to signal wakeup,
so pci_wakeup_event() may be a static inline function calling
pm_wakeup_event() directly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Move the evaluation of acpi_pci_osc_control_set() (to request control of
PCI Express native features) into acpi_pci_root_add() to avoid calling
it many times for the same root complex with the same arguments.
Additionally, check if all of the requisite _OSC support bits are set
before calling acpi_pci_osc_control_set() for a given root complex.
References: https://bugzilla.kernel.org/show_bug.cgi?id=20232
Reported-by: Ozan Caglayan <ozan@pardus.org.tr>
Tested-by: Ozan Caglayan <ozan@pardus.org.tr>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_restore_state only ever returns 0, thus there is no benefit in
having it return any value. Also, a large majority of the callers do
not check the return code of pci_restore_state. Make the
pci_restore_state a void return and avoid the overhead.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
It's helpful to have some extra PCI power management functions available to
platform code, so move the declarations to an exported header.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The name field in pci_driver should be const, it is not
modified by PCI subsystem.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Allows the new PCI domain aware DRM code to compile on m68k.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
It is a known issue that mmio decoding shall be disabled while doing PCI
bar sizing. Host bridge and other devices (PCI PIC) shall be excluded for
certain platforms. This patch mainly comes from Mathew Willcox's
patch in http://kerneltrap.org/mailarchive/linux-kernel/2007/9/13/258969.
A new flag bit "mmio_alway_on" is added to pci_dev with the intention that
devices with their mmio decoding cannot be disabled during BAR sizing shall
have this bit set, preferrablly in their quirks.
Without this patch, Intel Moorestown platform graphics unit will be
corrupted during bar sizing activities.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If we fail to assign resources to a PCI BAR, this patch makes us try the
original address from BIOS rather than leaving it disabled.
Linux tries to make sure all PCI device BARs are inside the upstream
PCI host bridge or P2P bridge apertures, reassigning BARs if necessary.
Windows does similar reassignment.
Before this patch, if we could not move a BAR into an aperture, we left
the resource unassigned, i.e., at address zero. Windows leaves such BARs
at the original BIOS addresses, and this patch makes Linux do the same.
This is a bit ugly because we disable the resource long before we try to
reassign it, so we have to keep track of the BIOS BAR address somewhere.
For lack of a better place, I put it in the struct pci_dev.
I think it would be cleaner to attempt the assignment immediately when the
claim fails, so we could easily remember the original address. But we
currently claim motherboard resources in the middle, after attempting to
claim PCI resources and before assigning new PCI resources, and changing
that is a fairly big job.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=16263
Reported-by: Andrew <nitr0@seti.kr.ua>
Tested-by: Andrew <nitr0@seti.kr.ua>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'linux_next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/i7core: (83 commits)
i7core_edac: Better describe the supported devices
Add support for Westmere to i7core_edac driver
i7core_edac: don't free on success
i7core_edac: Add support for X5670
Always call i7core_[ur]dimm_check_mc_ecc_err
i7core_edac: fix memory leak of i7core_dev
EDAC: add __init to i7core_xeon_pci_fixup
i7core_edac: Fix wrong device id for channel 1 devices
i7core: add support for Lynnfield alternate address
i7core_edac: Add initial support for Lynnfield
i7core_edac: do not export static functions
edac: fix i7core build
edac: i7core_edac produces undefined behaviour on 32bit
i7core_edac: Use a more generic approach for probing PCI devices
i7core_edac: PCI device is called NONCORE, instead of NOCORE
i7core_edac: Fix ringbuffer maxsize
i7core_edac: First store, then increment
i7core_edac: Better parse "any" addrmask
i7core_edac: Use a lockless ringbuffer
edac: Create an unique instance for each kobj
...
Now, a dedicated HEST tabling parsing code is used for PCIE AER
firmware_first setup. It is rebased on general HEST tabling parsing
code of APEI. The firmware_first setup code is moved from PCI core to
AER driver too, because it is only AER related.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This code changes the detection procedure of i7core_edac. Instead of
directly probing for MC registers, it probes for another register found
on Nehalem. If found, it tries to pick the first MC PCI BUS. This should
work fine with Xeon 35xx, but, on Xeon 55xx, this is at bus 254 and 255
that are not properly detected by the non-legacy PCI methods.
The new detection code scans specifically at buses 254 and 255 for the
Xeon 55xx devices.
This code has not tested yet. After working, a change at the code will
be needed, since the i7core is not yet ready for working with 2 sets of
MC.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When virtfn is used, we should use physfn to find correct drhd
-v2: add pci_physfn() Suggested by Roland Dreier <rdreier@cisco.com>
do can remove ifdef in dmar.c
-v3: Chris pointed out we need that for dma_find_matched_atsr_unit too
also change dmar_pci_device_match() static
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Roland Dreier <rdreier@cisco.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We can use pci-dma-compat.h to implement pci_set_dma_mask and
pci_set_consistent_dma_mask as we do with the other PCI DMA API.
We can remove HAVE_ARCH_PCI_SET_DMA_MASK too.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All the architectures properly set NEED_DMA_MAP_STATE now so we can safely
add linux/pci-dma.h to linux/pci.h and remove the linux/pci-dma.h
inclusion in arch's asm/pci.h
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-pci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Enable NMI on all cpus on UV
vgaarb: Add user selectability of the number of GPUS in a system
vgaarb: Fix VGA arbiter to accept PCI domains other than 0
x86, uv: Update UV arch to target Legacy VGA I/O correctly.
pci: Update pci_set_vga_state() to call arch functions
