The frequency passed to get_level() is returned by cpu_power_to_freq()
and it is guaranteed that get_level() can't fail.
Get rid of error code.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
We keep two arrays for idle time stats and allocate memory for them
separately. It would be much easier to follow if we create an array of
idle stats structure instead and allocate it once.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The cpu_cooling driver keeps two tables:
- freq_table: table of frequencies in descending order, built from
policy->freq_table.
- power_table: table of frequencies and power in ascending order, built
from OPP table.
If the OPPs are used for the CPU device then both these tables are
actually built using the OPP core and should have the same frequency
entries. And there is no need to keep separate tables for this.
Lets merge them both.
Note that the new table is in descending order of frequencies and so the
'for' loops were required to be fixed at few places to make it work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
'allowed_cpus' is a copy of policy->related_cpus and can be replaced by
it directly. At some places we are only concerned about online CPUs and
policy->cpus can be used there.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The OPPs are registered for all CPUs of a cpufreq policy now and we
don't need to run the loop in build_dyn_power_table(). Just check for
the policy->cpu and we should be fine.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The cpufreq policy can be used by the cpu_cooling driver, lets store it
in the cpufreq_cooling_device structure.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
We need such a routine at two places already, lets create one.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The CPU cooling driver uses the cpufreq policy, to get clip_cpus, the
frequency table, etc. Most of the callers of CPU cooling driver's
registration routines have the cpufreq policy with them, but they only
pass the policy->related_cpus cpumask. The __cpufreq_cooling_register()
routine then gets the policy by itself and uses it.
It would be much better if the callers can pass the policy instead
directly. This also fixes a basic design flaw, where the policy can be
freed while the CPU cooling driver is still active.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
'cpu' is used at only one place and there is no need to keep a separate
variable for it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
There is only one user of cpufreq_cooling_get_level() and that already
has pointer to the cpufreq_cdev structure. It can directly call
get_level() instead and we can get rid of cpufreq_cooling_get_level().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Objects of "struct thermal_cooling_device" are named a bit
inconsistently. Lets use cdev everywhere.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Objects of "struct cpufreq_cooling_device" are named a bit
inconsistently. Lets use cpufreq_cdev everywhere. Also note that the
lists containing such devices is renamed similarly too.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Just to make it look better.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
After the lock is dropped, it is possible that the cpufreq_dev gets
freed before we call get_level() and that can cause kernel to crash.
Drop the lock after we are done using the structure.
Cc: 4.2+ <stable@vger.kernel.org> # 4.2+
Fixes: 02373d7c69 ("thermal: cpu_cooling: fix lockdep problems in cpu_cooling")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Pull thermal management updates from Zhang Rui:
- Fix a problem where orderly_shutdown() is called for multiple times
due to multiple critical overheating events raised in a short period
by platform thermal driver. (Keerthy)
- Introduce a backup thermal shutdown mechanism, which invokes
kernel_power_off()/emergency_restart() directly, after
orderly_shutdown() being issued for certain amount of time(specified
via Kconfig). This is useful in certain conditions that userspace may
be unable to power off the system in a clean manner and leaves the
system in a critical state, like in the middle of driver probing
phase. (Keerthy)
- Introduce a new interface in thermal devfreq_cooling code so that the
driver can provide more precise data regarding actual power to the
thermal governor every time the power budget is calculated. (Lukasz
Luba)
- Introduce BCM 2835 soc thermal driver and northstar thermal driver,
within a new sub-folder. (Rafał Miłecki)
- Introduce DA9062/61 thermal driver. (Steve Twiss)
- Remove non-DT booting on TI-SoC driver. Also add support to fetching
coefficients from DT. (Keerthy)
- Refactorf RCAR Gen3 thermal driver. (Niklas Söderlund)
- Small fix on MTK and intel-soc-dts thermal driver. (Dawei Chien,
Brian Bian)
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (25 commits)
thermal: core: Add a back up thermal shutdown mechanism
thermal: core: Allow orderly_poweroff to be called only once
Thermal: Intel SoC DTS: Change interrupt request behavior
trace: thermal: add another parameter 'power' to the tracing function
thermal: devfreq_cooling: add new interface for direct power read
thermal: devfreq_cooling: refactor code and add get_voltage function
thermal: mt8173: minor mtk_thermal.c cleanups
thermal: bcm2835: move to the broadcom subdirectory
thermal: broadcom: ns: specify myself as MODULE_AUTHOR
thermal: da9062/61: Thermal junction temperature monitoring driver
Documentation: devicetree: thermal: da9062/61 TJUNC temperature binding
thermal: broadcom: add Northstar thermal driver
dt-bindings: thermal: add support for Broadcom's Northstar thermal
thermal: bcm2835: add thermal driver for bcm2835 SoC
dt-bindings: Add thermal zone to bcm2835-thermal example
thermal: rcar_gen3_thermal: add suspend and resume support
thermal: rcar_gen3_thermal: store device match data in private structure
thermal: rcar_gen3_thermal: enable hardware interrupts for trip points
thermal: rcar_gen3_thermal: record and check number of TSCs found
thermal: rcar_gen3_thermal: check that TSC exists before memory allocation
...
orderly_poweroff is triggered when a graceful shutdown
of system is desired. This may be used in many critical states of the
kernel such as when subsystems detects conditions such as critical
temperature conditions. However, in certain conditions in system
boot up sequences like those in the middle of driver probes being
initiated, userspace will be unable to power off the system in a clean
manner and leaves the system in a critical state. In cases like these,
the /sbin/poweroff will return success (having forked off to attempt
powering off the system. However, the system overall will fail to
completely poweroff (since other modules will be probed) and the system
is still functional with no userspace (since that would have shut itself
off).
However, there is no clean way of detecting such failure of userspace
powering off the system. In such scenarios, it is necessary for a backup
workqueue to be able to force a shutdown of the system when orderly
shutdown is not successful after a configurable time period.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
thermal_zone_device_check --> thermal_zone_device_update -->
handle_thermal_trip --> handle_critical_trips --> orderly_poweroff
The above sequence happens every 250/500 mS based on the configuration.
The orderly_poweroff function is getting called every 250/500 mS.
With a full fledged file system it takes at least 5-10 Seconds to
power off gracefully.
In that period due to the thermal_zone_device_check triggering
periodically the thermal work queues bombard with
orderly_poweroff calls multiple times eventually leading to
failures in gracefully powering off the system.
Make sure that orderly_poweroff is called only once.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The interrupt request call in Intel SoC DTS driver may fail if
there is no underlying BIOS support. However, the user space
thermal daemon can still use the thermal zones created by the
SoC DTS driver in polling mode, therefore, instead of bailing
out on interrupt request failures, it is better just to log
a warning message and continue the init process.
Signed-off-by: Brian Bian <brian.bian@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch adds another parameter to the trace function:
trace_thermal_power_devfreq_get_power().
In case when we call directly driver's code for the real power,
we do not have static/dynamic_power values. Instead we get total
power in the '*power' value. The 'static_power' and
'dynamic_power' are set to 0.
Therefore, we have to trace that '*power' value in this scenario.
CC: Steven Rostedt <rostedt@goodmis.org>
CC: Ingo Molnar <mingo@redhat.com>
CC: Zhang Rui <rui.zhang@intel.com>
CC: Eduardo Valentin <edubezval@gmail.com>
Acked-by: Javi Merino <javi.merino@kernel.org>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
This patch introduces a new interface for device drivers connected to
devfreq_cooling in the thermal framework: get_real_power().
Some devices have more sophisticated methods (like power counters)
to approximate the actual power that they use.
In the previous implementation we had a pre-calculated power
table which was then scaled by 'utilization'
('busy_time' and 'total_time' taken from devfreq 'last_status').
With this new interface the driver can provide more precise data
regarding actual power to the thermal governor every time the power
budget is calculated. We then use this value and calculate the real
resource utilization scaling factor.
Reviewed-by: Chris Diamand <chris.diamand@arm.com>
Acked-by: Javi Merino <javi.merino@kernel.org>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Move the code which gets the voltage for a given frequency.
This code will be resused in few places.
Acked-by: Javi Merino <javi.merino@kernel.org>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Crystal Cove and Whiskey Cove are two different PMICs which are
installed on Intel Atom SoC based platforms.
Moreover there are two independent drivers that by some reason were
supposed (*) to get into one kernel module.
Fix the mess by clarifying Kconfig option for Crystal Cove and split
Whiskey Cove out of it.
(*) It looks like the configuration was never tested with
INTEL_SOC_PMIC=n. The line in Makefile is actually wrong.
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> (supporter:ACPI)
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If thermal bank with 4 sensors, thermal driver should read TEMP_MSR3.
However, currently thermal driver would not read TEMP_MSR3 since mt8173
thermal driver only use 3 sensors on each thermal bank at the same time,
so this patch would not effect temperature.
Only if mt mt8173 thermal driver use 4 sensors on any thermal bank, would
read third sensor two times, and lose fourth sensor of vale.
cc: stable@vger.kernel.org
Fixes: b7cf005373 ("thermal: Add Mediatek thermal driver for mt2701.")
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Dawei Chien <dawei.chien@mediatek.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
We already have 2 Broadcom drivers and at least 1 more is coming. This
made us create broadcom subdirectory where bcm2835 should be moves now.
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Just in case someone uses modinfo to find (blame) me.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add junction temperature monitoring supervisor device driver, compatible
with the DA9062 and DA9061 PMICs. A MODULE_DEVICE_TABLE() macro is added.
If the PMIC's internal junction temperature rises above T_WARN (125 degC)
an interrupt is issued. This T_WARN level is defined as the
THERMAL_TRIP_HOT trip-wire inside the device driver.
The thermal triggering mechanism is interrupt based and happens when the
temperature rises above a given threshold level. The component cannot
return an exact temperature, it only has knowledge if the temperature is
above or below a given threshold value. A status bit must be polled to
detect when the temperature falls below that threshold level again. A
kernel work queue is configured to repeatedly poll and detect when the
temperature falls below this trip-wire, between 1 and 10 second intervals
(defaulting at 3 seconds).
This scheme is provided as an example. It would be expected that any
final implementation will also include a notify() function and any of these
settings could be altered to match the application where appropriate.
When over-temperature is reached, the interrupt from the DA9061/2 will be
repeatedly triggered. The IRQ is therefore disabled when the first
over-temperature event happens and the status bit is polled using a
work-queue until it becomes false.
This strategy is designed to allow the periodic transmission of uevents
(HOT trip point) as the first level of temperature supervision method. It
is intended for non-invasive temperature control, where the necessary
measures for cooling the system down are left to the host software. Once
the temperature falls again, the IRQ is re-enabled so a new critical
over-temperature event can be detected.
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Northstar is a SoC family commonly used in home routers. This commit
adds a driver for checking CPU temperature. As Northstar Plus seems to
also have this IP block this new symbol gets ARCH_BCM_IPROC dependency.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add basic thermal driver for bcm2835 SoC.
This driver currently make sure that tsense HW block is set up
correctly.
Tested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
To restore operation it's easiest to reinitialise all TSCs. In order to
do this the current trip window needs to be stored in the TSC structure
so that it can be restored upon resume.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The device match data needs to be accessible outside the probe function,
store it in the private data structure.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Enable hardware trip points by implementing the set_trips callback. The
thermal core will take care of setting the initial trip point window and
to update it once the driver reports a TSC has moved outside it.
The interrupt structure for this device is a bit odd. There is not a
dedicated IRQ for each TSC, instead the interrupts are shared between
all TSCs. IRQn is fired if the temp monitored in IRQTEMPn is reached in
any of the TSCs, example IRQ3 is fired if temperature in IRQTEMP3 is
reached in either TSC0, TSC1 or TSC2.
For this reason the usage of interrupts in this driver is an all-on or
all-off design. When an interrupt happens all TSCs are checked and all
thermal zones are updated. This could be refined to be more fine grained
but the thermal core takes care of only updating the thermal zones that
have left their trip point window.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Record how many TSCs are found in struct rcar_gen3_thermal_priv, this is
needed to be able to add hardware interrupts for trip points later. Also
add a check to make sure at least one TSC is found.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Move the check for a TSC resource before allocating memory for a new
TSC. If no TSC is found there is little point in allocating memory for
it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
There is no point in protecting a register read with a lock. This is
most likely a leftover from when the driver was reworked before being
submitted for upstream.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The .thermal_init needs to be delayed a short amount of time to allow
for the TEMP register to contain something useful. If it's not delayed
these warnings are common during boot:
thermal thermal_zone0: failed to read out thermal zone (-5)
thermal thermal_zone1: failed to read out thermal zone (-5)
thermal thermal_zone2: failed to read out thermal zone (-5)
The warnings are triggered by the first call to .get_temp() while the
TEMP register contains 0 and rcar_gen3_thermal_get_temp() returns -EIO
since a TEMP value of 0 will result in a temperature reading which is
out of specifications.
This should have been done in the initial commit which adds the driver
as the same issue was found and corrected for r8a7795.
Fixes: 564e73d283 ("thermal: rcar_gen3_thermal: Add R-Car Gen3 thermal driver")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
ti_thermal_expose_sensor always takes the
devm_thermal_zone_of_sensor_register call for registration
with the device tree nodes present for all the bandgap sensors
for omap3/4/5 and dra7 family. There are large chunks of unused
code. Removing all of them.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Now that slope and offset data are being passed from
device tree no need to populate in driver data.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Currently slope and offset values for calculating the hot spot
temperature of a thermal zone is being taken directly from driver
data. So fetch them from device tree.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The best place to register the CPU cooling device is from the cpufreq
driver as we would know if all the resources are already available or
not. That's what is done for the cpufreq-dt.c driver as well.
The cpu-cooling driver for dbx500 platform was just (un)registering
with the thermal framework and that can be handled easily by the cpufreq
driver as well and in proper sequence as well.
Get rid of the cooling driver and its its users and manage everything
from the cpufreq driver instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is possible for dev_pm_opp_find_freq_exact() to return errors. It was
all fine earlier as dev_pm_opp_get_voltage() had a check within it to
check for invalid OPPs, but dev_pm_opp_put() doesn't have any similar
checks and the callers need to make sure OPP is valid before calling
them.
Also update the later dev_warn_ratelimited() to not print the error
message as the OPP is guaranteed to be valid now.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
There isn't much the user can do on seeing these warnings, as the
hardware is actually okay. dev_err suits much better here.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
It is possible for dev_pm_opp_find_freq_exact() to return errors. It was
all fine earlier as dev_pm_opp_get_voltage() had a check within it to
check for invalid OPPs, but dev_pm_opp_put() doesn't have any similar
checks and the callers need to make sure OPP is valid before calling
them.
Also update the later dev_warn_ratelimited() to not print the error
message as the OPP is guaranteed to be valid now.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
There isn't much the user can do on seeing this warning, as the hardware
is actually okay. dev_err suits much better here.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
There is no need to check for IS_ERR() as we are looking for a very
particular error value here. Drop the first check.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
