On Thu, 1 Feb 2007, Andrew Morton wrote:
> On Thu, 1 Feb 2007 15:34:29 -0800
> bugme-daemon@bugzilla.kernel.org wrote:
>
> > http://bugzilla.kernel.org/show_bug.cgi?id=7919
> >
> > Summary: Tape dies if wrong block size used
> > Kernel Version: 2.6.20-rc5
> > Status: NEW
> > Severity: normal
> > Owner: scsi_drivers-other@kernel-bugs.osdl.org
> > Submitter: dmartin@sccd.ctc.edu
> >
> >
> > Most recent kernel where this bug did *NOT* occur: 2.6.17.14
> >
> > Other Kernels Tested and Results:
> >
> > OK 2.6.15.7
> > OK 2.6.16.37
> > OK 2.6.17.14
> > BAD 2.6.18.6
> > BAD 2.6.18-1.2869.fc6
> > BAD 2.6.19.2 +
> > BAD 2.6.20-rc5
> >
> > NOTE: 2.6.18-1.2869.fc6 is a Fedora modified kernel, all others are from kernel.org
> >
...
> > Steps to reproduce:
> > Get a Adaptec AHA-2940U/UW/D / AIC-7881U card and a tape drive,
> > install a recent kernel
> > set the tape block size - mt setblk 4096
> > read from or write to tape using wrong block size - tar -b 7 -cvf /dev/tape foo
> >
Write does not trigger this bug because the driver refuses in fixed block
mode writes that are not a multiple of the block size. Read does trigger
it in my system.
The bug is not associated with any specific HBA. st tries to do direct i/o
in fixed block mode with reads that are not a multiple of tape block size.
The patch in this message fixes the st problem by switching to using the
driver buffer up to the next close of the device file in fixed block mode
if the user asks for a read like this.
I don't know why the bug has surfaced only after 2.6.17 although the st
problem is old. There may be another bug in the block subsystem and this
patch works around it. However, the patch fixes a problem in st and in
this way it is a valid fix.
This patch may also fix the bug 7900.
The patch compiles and is lightly tested.
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
I noticed that in_use in st_buffer is not used. The patch below
against 2.6.17-rc3 removes it, assuming there is no future use for it.
It was tested in a sparc SS20 with a DLT4000.
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
convert st to always send scatterlists and kill scsi_request
usage.
This is the same as last time as it was posted, but with Kai's patches
merged and we now pass the bytes value to scsi_execute_async.
TODO:
- move DIO code to common place or make block layers usable for ULDs.
- move buffer allocation code to common place for all ULDs to use. And
make buffer allocation code handle all queue limits so we can find
out about problems before calling scsi_execute_async.
- move indirect (copy_to/from_user) paths commone place or make block
layers usable for ULDs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
I have rediffed the patch against 2.6.13-rc5, done a couple of cosmetic
cleanups, and run some tests. Brian King has acknowledged that it fixes the
problems he has seen. Seems mature enough for inclusion into 2.6.14 (or
later)?
Nate's explanation of the changes:
I've attached patches against 2.6.13rc2. These are basically identical
to my earlier patches, as I found that all issues I'd seen in earlier
kernels still existed in this kernel.
To summarize, the changes are: (more details in my original email)
- add a kref to the scsi_tape structure, and associate reference
counting stuff
- set sr_request->end_io = blk_end_sync_rq so we get notified when an IO
is rejected when the device goes away
- check rq_status when IOs complete, else we don't know that IOs
rejected for a dead device in fact did not complete
- change last_SRpnt so it's set before an async IO is issued (in case
st_sleep_done is bypassed)
- fix a bogus use of last_SRpnt in st_chk_result
Signed-off-by: Nate Dailey <nate.dailey@stratus.com>
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
