S3C6410 system restart is triggered by watchdog reset.
Cc: <stable@vger.kernel.org>
Fixes: 9f55342cc2 ("ARM: dts: s3c64xx: Fix infinite interrupt in soft mode")
Signed-off-by: Lihua Yao <ylhuajnu@outlook.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
While parts of the VGIC support a large number of vcpus (we
bravely allow up to 512), other parts are more limited.
One of these limits is visible in the KVM_IRQ_LINE ioctl, which
only allows 256 vcpus to be signalled when using the CPU or PPI
types. Unfortunately, we've cornered ourselves badly by allocating
all the bits in the irq field.
Since the irq_type subfield (8 bit wide) is currently only taking
the values 0, 1 and 2 (and we have been careful not to allow anything
else), let's reduce this field to only 4 bits, and allocate the
remaining 4 bits to a vcpu2_index, which acts as a multiplier:
vcpu_id = 256 * vcpu2_index + vcpu_index
With that, and a new capability (KVM_CAP_ARM_IRQ_LINE_LAYOUT_2)
allowing this to be discovered, it becomes possible to inject
PPIs to up to 4096 vcpus. But please just don't.
Whilst we're there, add a clarification about the use of KVM_IRQ_LINE
on arm, which is not completely conditionned by KVM_CAP_IRQCHIP.
Reported-by: Zenghui Yu <yuzenghui@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Since commit 1137ceee76 ("ARM: OMAP1: ams-delta: Don't request unused
GPIOs"), on-board audio has appeared muted. It has been discovered that
believed to be unused GPIO pins "hookflash1" and "hookflash2" need to be
set low for audible sound in handsfree and handset mode respectively.
According to Amstrad E3 wiki, the purpose of both pins hasn't been
clearly identified. Original Amstrad software used to produce a high
pulse on them when the phone was taken off hook or recall was pressed.
With the current findings, we can assume the pins provide a kind of
audio mute function, separately for handset and handsfree operation
modes.
Commit 2afdb4c41d ("ARM: OMAP1: ams-delta: Fix audio permanently
muted") attempted to fix the issue temporarily by hogging the GPIO pin
"hookflash1" renamed to "audio_mute", however the fix occurred
incomplete as it restored audible sound only for handsfree mode.
Stop hogging that pin, rename the pins to "handsfree_mute" and
"handset_mute" respectively and implement appropriate DAPM event
callbacks for "Speaker" and "Earpiece" DAPM widgets.
Fixes: 1137ceee76 ("ARM: OMAP1: ams-delta: Don't request unused GPIOs")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20190907111650.15440-1-jmkrzyszt@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of relying on the CTS template to wrap the accelerated CBC
skcipher, implement the ciphertext stealing part directly.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Update the AES-XTS implementation based on NEON instructions so that it
can deal with inputs whose size is not a multiple of the cipher block
size. This is part of the original XTS specification, but was never
implemented before in the Linux kernel.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Update the AES-XTS implementation based on AES instructions so that it
can deal with inputs whose size is not a multiple of the cipher block
size. This is part of the original XTS specification, but was never
implemented before in the Linux kernel.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Replace the vector load from memory sequence with a simple instruction
sequence to compose the tweak vector directly.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Replace the vector load from memory sequence with a simple instruction
sequence to compose the tweak vector directly.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When the ARM AES instruction based crypto driver was introduced, there
were no known implementations that could benefit from a 4-way interleave,
and so a 3-way interleave was used instead. Since we have sufficient
space in the SIMD register file, let's switch to a 4-way interleave to
align with the 64-bit driver, and to ensure that we can reach optimum
performance when running under emulation on high end 64-bit cores.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reduce the scope of the kernel_neon_begin/end regions so that the SIMD
unit is released (and thus preemption re-enabled) if the crypto operation
cannot be completed in a single scatterwalk step. This avoids scheduling
blackouts due to preemption being enabled for unbounded periods, resulting
in a more responsive system.
After this change, we can also permit the cipher_walk infrastructure to
sleep, so set the 'atomic' parameter to skcipher_walk_virt() to false as
well.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The AES round keys are arrays of u32s in native endianness now, so
update the function prototypes accordingly.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This is a fairly complete description of an OLPC XO 1.75 laptop.
What's missing for now is the GPU, LCD controller, DCON, the panel and
audio.
The machine is booted with OpenFirmware and thus has a devicetree.
However, older versions are unable to create a valid FDT and don't
follow the Linux bindings. Having an device tree in the kernel tree
makes it easier to use mainline kernels on such machines, test changes
with CONFIG_ARM_APPENDED_DTB and give a good reference on what bindings
are used on the machine without an access to one.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
This device is not an OTG phy, it's a regular USB HS phy. Follow the
generic node name recommendation, and rename it to "usb-phy".
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
This makes the 8250_of driver happy. There are two more drivers in the
tree that bind to mrvl,mmp-uart compatibles: pxa and 8250_pxa and
neither of them requires the reg-shift property, assuming it's always 2.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
The SPI bus has a single address cell and not size cells.
Also, dtc thinks the SPI nodes are preferrably called "spi" and it is
right to think so.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
When the pinmux configuration was added, it was accidentally placed into
the omap3_pmx_wkup node when it should have been placed into the
omap3_pmx_core. This error was accidentally propagated to stable by
me when I blindly requested the pull after seeing I2C issues without
actually reviewing the content of the pinout. Since the bootloader
previously muxed these correctly in the past, was a hidden error.
This patch moves the i2c2_pins and i2c3_pins to the correct node
which should eliminate i2c bus errors and timeouts due to the fact
the bootloader uses the save device tree that no longer properly
assigns these pins.
Fixes: 5fe3c0fa0d ("ARM: dts: Add pinmuxing for i2c2 and i2c3
for LogicPD SOM-LV") #4.9+
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The calculation of memblock_limit in adjust_lowmem_bounds() assumes that
bank 0 starts from a PMD-aligned address. However, the beginning of the
first bank may be NOMAP memory and the start of usable memory
will be not aligned to PMD boundary. In such case the memblock_limit will
be set to the end of the NOMAP region, which will prevent any memblock
allocations.
Mark the region between the end of the NOMAP area and the next PMD-aligned
address as NOMAP as well, so that the usable memory will start at
PMD-aligned address.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
A previous commit removed the panel-dpi driver, which made the
video on the AM3517-evm stop working because it relied on the dpi
driver for setting video timings. Now that the simple-panel driver
is available in omap2plus, this patch migrates the am3517-evm
to use a similar panel and remove the manual timing requirements.
Fixes: 8bf4b16211 ("drm/omap: Remove panel-dpi driver")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A previous commit removed the panel-dpi driver, which made the
Torpedo video stop working because it relied on the dpi driver
for setting video timings. Now that the simple-panel driver is
available in omap2plus, this patch migrates the Torpedo dev kits
to use a similar panel and remove the manual timing requirements.
Fixes: 8bf4b16211 ("drm/omap: Remove panel-dpi driver")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When the panel-dpi driver was removed, the simple-panels driver
was never enabled, so anyone who used the panel-dpi driver lost
video, and those who used it inconjunction with simple-panels
would have to manually enable CONFIG_DRM_PANEL_SIMPLE.
This patch makes CONFIG_DRM_PANEL_SIMPLE a module in the same
way the deprecated panel-dpi was.
Fixes: 8bf4b16211 ("drm/omap: Remove panel-dpi driver")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Large GICv3 updates to support new PPI and SPI ranges
- Conver all alloc_fwnode() users to use PAs instead of VAs
- Add support for Marvell's MMP3 irqchip
- Add support for Amlogic Meson SM1
- Various cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=PsGr
-----END PGP SIGNATURE-----
Merge tag 'irqchip-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates for Linux 5.4 from Marc Zyngier:
- Large GICv3 updates to support new PPI and SPI ranges
- Conver all alloc_fwnode() users to use PAs instead of VAs
- Add support for Marvell's MMP3 irqchip
- Add support for Amlogic Meson SM1
- Various cleanups and fixes
We can currently get "Unable to handle kernel paging request at
virtual address" for invalid clocks with dts node but no driver:
(__clk_get_hw) from [<c0138ebc>] (ti_sysc_find_one_clockdomain+0x18/0x34)
(ti_sysc_find_one_clockdomain) from [<c0138f0c>] (ti_sysc_clkdm_init+0x34/0xdc)
(ti_sysc_clkdm_init) from [<c0584660>] (sysc_probe+0xa50/0x10e8)
(sysc_probe) from [<c065c6ac>] (platform_drv_probe+0x58/0xa8)
Let's add IS_ERR checks to ti_sysc_clkdm_init() as And let's start treating
clk_get() with -ENOENT as a proper error. If the clock name is specified
in device tree we must succeed with clk_get() to continue. For modules with
no clock names specified in device tree we will just ignore the clocks.
Fixes: 2b2f7def05 ("bus: ti-sysc: Add support for missing clockdomain handling")
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
any market.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAl1w+fEQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgaolB/9QiQc2k2HFAwQTS1RpvVW87yKdLXPhqBBs
HhagbY3ucMXDY38tZnLnbLis6CwdvkeHCCL6KC9XLzIgiJZHzXhb+QLiu9YLAw25
ymnWVtamVh0WmSNOBqex65fXwCQH9l/godI8BaxltllEkb472/jwainqHsVkFI7Z
idVGrTo9zgW7NTGQU88Rl6cagHLR6OpHBvc5meu7TIzGYF2U+Xx+x9TZw7BfdQ7u
gKZtIeRTFwsHdiBNbeU78znQCW/apCyzyKaIKW517TiXQsmsm/CEGai2/+XTN0ft
+QqHkXO7NBUh0cPZvBefq53EyDlvJbv1TW+XXP9d+TTFotTtJmXU
=PkdV
-----END PGP SIGNATURE-----
Merge tag 'v5.4-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
Removal of the rk3288-fennec board which never made it to
any market.
* tag 'v5.4-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
dt-bindings: arm: rockchip: remove reference to fennec board
ARM: dts: rockchip: remove rk3288 fennec board support
Link: https://lore.kernel.org/r/1718334.9BoTfW0Ujv@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Alternate flash support for Vesnin
- Minor cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=ranz
-----END PGP SIGNATURE-----
Merge tag 'aspeed-5.4-devicetree-2' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into arm/dt
ASPEED device tree updates for 5.4, second round
- Alternate flash support for Vesnin
- Minor cleanups and fixes
* tag 'aspeed-5.4-devicetree-2' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: dts: aspeed-g5: Fixe gpio-ranges upper limit
ARM; dts: aspeed: mihawk: File should not be executable
ARM: dts: aspeed: swift: Change power supplies to version 2
ARM: dts: aspeed: vesnin: Add secondary SPI flash chip
ARM: dts: aspeed: vesnin: Add wdt2 with alt-boot option
ARM: dts: aspeed-g4: Add all flash chips
Link: https://lore.kernel.org/r/CACPK8Xdp4gVuetmiu2bRTTH6oHhRrC7FELHWKVB2ZGSbPbH7HQ@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Rename static / file-local functions so that they do not conflict with
the functions declared in crypto/sha256.h.
This is a preparation patch for folding crypto/sha256.h into crypto/sha.h.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
According to the AST2500/AST2520 specs, these SoCs support up to 228 GPIO
pins. However, 'gpio-ranges' value in 'aspeed-g5.dtsi' file is currently
setting the upper limit to 220 which isn't allowing access to all their
GPIOs. The correct upper limit value is 232 (actual number is 228 plus a
4-GPIO hole in GPIOAB). Without this patch, GPIOs AC5 and AC6 do not work
correctly on a AST2500 BMC running Linux Kernel v4.19
Fixes: 2039f90d13 ("ARM: dts: aspeed-g5: Add gpio controller to devicetree")
Signed-off-by: Oscar A Perez <linux@neuralgames.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Swift power supplies are version 2 of the IBM CFFPS.
Fixes: 8e8fd0cbd7 ("ARM: dts: aspeed: Add Swift BMC machine")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Adds wdt2 section with 'alt-boot' option into dts for vesnin.
Signed-off-by: Ivan Mikhaylov <i.mikhaylov@yadro.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The FMC supports five chip selects, so describe the five possible flash
chips.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
1. Minor fixup in plat and mach code (S3C platforms),
2. Enable exynos-chipid driver to provide SoC related information,
3. Extend the patterns for Samsung maintainer entries to cover all
important files.
-----BEGIN PGP SIGNATURE-----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=S0YI
-----END PGP SIGNATURE-----
Merge tag 'samsung-soc-5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/soc
Samsung mach/soc changes for v5.4
1. Minor fixup in plat and mach code (S3C platforms),
2. Enable exynos-chipid driver to provide SoC related information,
3. Extend the patterns for Samsung maintainer entries to cover all
important files.
* tag 'samsung-soc-5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
MAINTAINERS: Extend patterns for Samsung SoC, Security Subsystem and clock drivers
ARM: s3c64xx: squash samsung_usb_phy.h into setup-usb-phy.c
ARM: exynos: Enable exynos-chipid driver
ARM: samsung: Include GPIO driver header
Link: https://lore.kernel.org/r/20190904175002.10487-5-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
1. Enable AHCI platform driver on exynos defconfig for Exynos5250-based
Arndale board,
2. Make Max77802 PMIC regulator driver a built-in on multi_v7 defconfig
as it is essential early during boot.
-----BEGIN PGP SIGNATURE-----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=30RN
-----END PGP SIGNATURE-----
Merge tag 'samsung-defconfig-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/defconfig
Samsung defconfig changes for v5.4
1. Enable AHCI platform driver on exynos defconfig for Exynos5250-based
Arndale board,
2. Make Max77802 PMIC regulator driver a built-in on multi_v7 defconfig
as it is essential early during boot.
* tag 'samsung-defconfig-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: multi_v7_defconfig: Make MAX77802 regulator driver built-in
ARM: exynos_defconfig: Enable AHCI-platform SATA driver
Link: https://lore.kernel.org/r/20190904175002.10487-2-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested with kmscube and some glmark2* tests on arndale board.
Signed-off-by: Guillaume Gardet <guillaume.gardet@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested with kmscube and some glmark2* tests on Chromebook snow.
Frequency adapts with load.
Signed-off-by: Guillaume Gardet <guillaume.gardet@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Required to have GPU voltage scaling working properly.
Signed-off-by: Guillaume Gardet <guillaume.gardet@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
For a while we've had omap4 sgx glue layer defined in dts and probed
with ti-sysc driver. This allows idling the sgx module for PM, and
removes the need for custom platform glue layer code for any further
driver changes.
We first drop the unused legacy platform data for omap4 sgx. Then for
omap5, we need add the missing clkctrl clock data so we can configure
sgx. And we configure sgx for omap34xx, omap36xx and am3517.
For am335x, we still have a dependency for rstctrl reset driver changes,
so that will be added later on.
Note that this branch is based on earlier ti-sysc branch for omap36xx
glue layer quirk handling.
-----BEGIN PGP SIGNATURE-----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=a2cp
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.4/ti-sysc-sgx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/late
SoC glue layer changes for SGX on omap variants for v5.4
For a while we've had omap4 sgx glue layer defined in dts and probed
with ti-sysc driver. This allows idling the sgx module for PM, and
removes the need for custom platform glue layer code for any further
driver changes.
We first drop the unused legacy platform data for omap4 sgx. Then for
omap5, we need add the missing clkctrl clock data so we can configure
sgx. And we configure sgx for omap34xx, omap36xx and am3517.
For am335x, we still have a dependency for rstctrl reset driver changes,
so that will be added later on.
Note that this branch is based on earlier ti-sysc branch for omap36xx
glue layer quirk handling.
* tag 'omap-for-v5.4/ti-sysc-sgx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: ARM: dts: Configure interconnect target module for am3517sgx
ARM: dts: Configure interconnect target module for omap3 sgx
ARM: dts: Configure sgx for omap5
clk: ti: add clkctrl data omap5 sgx
ARM: OMAP2+: Drop legacy platform data for omap4 gpu
Link: https://lore.kernel.org/r/pull-1567016893-318461@atomide.com-4
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We can now drop more platform data in favor of dts data for most
devices like cpsw, gpio, i2c, mmc, uart and watchdog.
In general we can do this by dropping legacy "ti,hwmods" custom dts
property, and the platform data assuming the related dts data is correct.
This is best done as single patch as otherwise we'd have to revert two
patches in case of any unexpected issues, and we're just removing data.
Fro cpsw, before we can do this, we need to configure the cpsw mdio clocks
properly in dts though in the first patch. For omap4 i2c, we've already
dropped the platform data earlier, but have been still allocting it
dynamically based on the dts data based on the "ti,hwmods" property, but
that is no longer needed. For d2d, we are missing the dts data, so we
first add it and then drop the platform data.
For dra7, we drop platform data and "ti,hwmods" for mcasp and mcspi.
We've already dropped platform data earlier for gpio, i2c, mmc, and
uart so we just need to drop "ti,hwmods" property for those.
Note that this branch is based on earlier ti-sysc-fixes branch.
-----BEGIN PGP SIGNATURE-----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=mBPp
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.4/ti-sysc-drop-pdata-take2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/late
Drop legacy platform data omap variants for v5.4
We can now drop more platform data in favor of dts data for most
devices like cpsw, gpio, i2c, mmc, uart and watchdog.
In general we can do this by dropping legacy "ti,hwmods" custom dts
property, and the platform data assuming the related dts data is correct.
This is best done as single patch as otherwise we'd have to revert two
patches in case of any unexpected issues, and we're just removing data.
Fro cpsw, before we can do this, we need to configure the cpsw mdio clocks
properly in dts though in the first patch. For omap4 i2c, we've already
dropped the platform data earlier, but have been still allocting it
dynamically based on the dts data based on the "ti,hwmods" property, but
that is no longer needed. For d2d, we are missing the dts data, so we
first add it and then drop the platform data.
For dra7, we drop platform data and "ti,hwmods" for mcasp and mcspi.
We've already dropped platform data earlier for gpio, i2c, mmc, and
uart so we just need to drop "ti,hwmods" property for those.
Note that this branch is based on earlier ti-sysc-fixes branch.
* tag 'omap-for-v5.4/ti-sysc-drop-pdata-take2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Drop legacy custom hwmods property for dra7 gpio
ARM: dts: Drop legacy custom hwmods property for dra7 mmc
ARM: dts: Drop legacy custom hwmods property for dra7 i2c
ARM: dts: Drop legacy custom hwmods property for dra7 uart
ARM: OMAP2+: Drop legacy platform data for dra7 mcasp
ARM: OMAP2+: Drop legacy platform data for dra7 mcspi
ARM: OMAP2+: Drop legacy platform data for omap4 d2d
ARM: dts: Configure d2d dts data for omap4
ARM: OMAP2+: Drop legacy watchdog platform data for omap4
ARM: dts: Drop custom hwmod property for omap4 i2c
ARM: OMAP2+: Drop legacy platform data for cpsw on dra7
ARM: OMAP2+: Drop legacy platform data for cpsw on am3 and am4
ARM: dts: Add fck for cpsw mdio for omap variants
Link: https://lore.kernel.org/r/pull-1567016893-318461@atomide.com-3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
for 5.4, please pull the following:
- Stefan does a bunch of preparatory work for supporting the Raspberry
Pi 4in the next merge window correct register ranges (SPI, I2C,
UART), define memory, HDMI and MMC properties at the board level
-----BEGIN PGP SIGNATURE-----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=DR09
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.4/devicetree' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM-based SoCs Device Tree updates
for 5.4, please pull the following:
- Stefan does a bunch of preparatory work for supporting the Raspberry
Pi 4in the next merge window correct register ranges (SPI, I2C,
UART), define memory, HDMI and MMC properties at the board level
* tag 'arm-soc/for-5.4/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm283x: Enable HDMI at board level
ARM: dts: bcm283x: Define memory at board level
ARM: dts: bcm283x: Define MMC interfaces at board level
ARM: bcm283x: Reduce register ranges for UART, SPI and I2C
* Add DRM_MSM to ARCH_QCOM defconfigs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0xTo
-----END PGP SIGNATURE-----
Merge tag 'qcom-defconfig-for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/defconfig
Qualcomm ARM Based defconfig Updates for v5.4
* Add DRM_MSM to ARCH_QCOM defconfigs
* tag 'qcom-defconfig-for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: multi_v7_defconfig: Add DRM_MSM to defconfigs with ARCH_QCOM
ARM: qcom_defconfig: Add DRM_MSM to defconfigs with ARCH_QCOM
This helps SPI NOR to work on newer board variants.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZBa8
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v5.4/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into arm/dt
Contains a patch to switch to more generic compatible for SPI NOR.
This helps SPI NOR to work on newer board variants.
* tag 'davinci-for-v5.4/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850-evm: Use generic jedec, spi-nor for flash
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
and regulator devices. This will finally help get rid of legacy
GPIO API calls and simplify DaVinci GPIO driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=GdvX
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v5.4/fbdev' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into arm/drivers
This converts the da8xx fbdev driver to use GPIO backlight device
and regulator devices. This will finally help get rid of legacy
GPIO API calls and simplify DaVinci GPIO driver.
* tag 'davinci-for-v5.4/fbdev' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
fbdev: da8xx: use resource management for dma
fbdev: da8xx-fb: drop a redundant if
fbdev: da8xx-fb: use devm_platform_ioremap_resource()
fbdev: da8xx: remove panel_power_ctrl() callback from platform data
ARM: davinci: da850-evm: switch to using a fixed regulator for lcdc
fbdev: da8xx: add support for a regulator
ARM: davinci: da850-evm: model the backlight GPIO as an actual device
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Kbuild provides per-file compiler flag addition/removal:
CFLAGS_<basetarget>.o
CFLAGS_REMOVE_<basetarget>.o
AFLAGS_<basetarget>.o
AFLAGS_REMOVE_<basetarget>.o
CPPFLAGS_<basetarget>.lds
HOSTCFLAGS_<basetarget>.o
HOSTCXXFLAGS_<basetarget>.o
The <basetarget> is the filename of the target with its directory and
suffix stripped.
This syntax comes into a trouble when two files with the same basename
appear in one Makefile, for example:
obj-y += foo.o
obj-y += dir/foo.o
CFLAGS_foo.o := <some-flags>
Here, the <some-flags> applies to both foo.o and dir/foo.o
The real world problem is:
scripts/kconfig/util.c
scripts/kconfig/lxdialog/util.c
Both files are compiled into scripts/kconfig/mconf, but only the
latter should be given with the ncurses flags.
It is more sensible to use the relative path to the Makefile, like this:
obj-y += foo.o
CFLAGS_foo.o := <some-flags>
obj-y += dir/foo.o
CFLAGS_dir/foo.o := <other-flags>
At first, I attempted to replace $(basetarget) with $*. The $* variable
is replaced with the stem ('%') part in a pattern rule. This works with
most of cases, but does not for explicit rules.
For example, arch/ia64/lib/Makefile reuses rule_as_o_S in its own
explicit rules, so $* will be empty, resulting in ignoring the per-file
AFLAGS.
I introduced a new variable, target-stem, which can be used also from
explicit rules.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Marc Zyngier <maz@kernel.org>
driver. DM365 conversion is still under debug and will be part of a
future pull request.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7VBk
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v5.4/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into arm/soc
This converts all DaVinci SoCs except DM365 to use new clocksource
driver. DM365 conversion is still under debug and will be part of a
future pull request.
* tag 'davinci-for-v5.4/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: dm646x: Fix a typo in the comment
ARM: davinci: dm646x: switch to using the clocksource driver
ARM: davinci: dm644x: switch to using the clocksource driver
ARM: davinci: dm355: switch to using the clocksource driver
ARM: davinci: move timer definitions to davinci.h
ARM: davinci: da830: switch to using the clocksource driver
ARM: davinci: da850: switch to using the clocksource driver
ARM: davinci: WARN_ON() if clk_get() fails
ARM: davinci: enable the clocksource driver for DT mode
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
5.4, please pull the following:
- Nicolas enables the Raspberry Pi CPUFREQ driver in both
bcm2835_defconfig and multi_v7_defconfig
-----BEGIN PGP SIGNATURE-----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=dVMC
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.4/defconfig' of https://github.com/Broadcom/stblinux into arm/defconfig
This pull request contains Broadcom ARM-based SoCs defconfig updates for
5.4, please pull the following:
- Nicolas enables the Raspberry Pi CPUFREQ driver in both
bcm2835_defconfig and multi_v7_defconfig
* tag 'arm-soc/for-5.4/defconfig' of https://github.com/Broadcom/stblinux:
ARM: defconfig: enable cpufreq driver for RPi
A helper to find the backing page array based on a virtual address.
This also ensures we do the same vm_flags check everywhere instead
of slightly different or missing ones in a few places.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Currently the generic dma remap allocator gets a vm_flags passed by
the caller that is a little confusing. We just introduced a generic
vmalloc-level flag to identify the dma coherent allocations, so use
that everywhere and remove the now pointless argument.
Signed-off-by: Christoph Hellwig <hch@lst.de>
The arm architecture had a VM_ARM_DMA_CONSISTENT flag to mark DMA
coherent remapping for a while. Lift this flag to common code so
that we can use it generically. We also check it in the only place
VM_USERMAP is directly check so that we can entirely replace that
flag as well (although I'm not even sure why we'd want to allow
remapping DMA appings, but I'd rather not change behavior).
Signed-off-by: Christoph Hellwig <hch@lst.de>
Most dma_map_ops instances are IOMMUs that work perfectly fine in 32-bits
of IOVA space, and the generic direct mapping code already provides its
own routines that is intelligent based on the amount of memory actually
present. Wire up the dma-direct routine for the ARM direct mapping code
as well, and otherwise default to the constant 32-bit mask. This way
we only need to override it for the occasional odd IOMMU that requires
64-bit IOVA support, or IOMMU drivers that are more efficient if they
can fall back to the direct mapping.
Signed-off-by: Christoph Hellwig <hch@lst.de>
There is no need to go through dma_common_mmap for the arm-nommu
dma mmap implementation as the only possible memory not handled above
could be that from the per-device coherent pool.
Signed-off-by: Christoph Hellwig <hch@lst.de>
- Low-level debugging support for RZ/A2M.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXV/PyQAKCRCKwlD9ZEnx
cPvMAQCJ+/oDXHyg48BknWJd2HRMpGAkv4/YS+TM7GWkeVc5YQEA4vF2sQV8Q1zf
NmMRB9sAHnROZb7GiLHkynHDDpjYYQk=
=r42g
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm-soc-for-v5.4-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/soc
Renesas ARM SoC updates for v5.4
- Low-level debugging support for RZ/A2M.
* tag 'renesas-arm-soc-for-v5.4-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
ARM: debug-ll: Add support for r7s9210
Link: https://lore.kernel.org/r/20190823123643.18799-3-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Add support for SMP in thumb mode
- Fix SMP trampoline code when FORTIFY_SOURCE is enabled
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXW5yWgAKCRDKSWXLKUoM
ISrxAJ4vzP6qLTLr2vN9qDQ4XM63kQ/RiQCdEEBejxseeXtdj1xO+s4NebRlkiA=
=0zGR
-----END PGP SIGNATURE-----
Merge tag 'zynq-soc-for-v5.4' of https://github.com/Xilinx/linux-xlnx into arm/soc
ARM: Xilinx Zynq SoC patches for v5.4
- Add support for SMP in thumb mode
- Fix SMP trampoline code when FORTIFY_SOURCE is enabled
* tag 'zynq-soc-for-v5.4' of https://github.com/Xilinx/linux-xlnx:
ARM: zynq: Use memcpy_toio instead of memcpy on smp bring-up
ARM: zynq: Support smp in thumb mode
Link: https://lore.kernel.org/r/8e00ba70-9403-4bf7-2870-a94758e37346@monstr.eu
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This is a GPIO driver so it should include
<linux/gpio/driver.h> not <linux/gpio.h>
Link: https://lore.kernel.org/r/20190820103429.7028-1-linus.walleij@linaro.org
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Enable pinctrl and clock driver support for i.MX8MN SoC.
- Enable SDMA support for i.MX8MQ and i.MX8MM SoC, including
FW_LOADER_USER_HELPER and FW_LOADER_USER_HELPER_FALLBACK to support
SDMA firmware loading via udev.
- Enable module build of i.MX8 DDR PMU driver and ETNAVIV GPU driver.
- Enable module build of OV5645 camera driver in imx_v6_v7_defconfig.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdYqWeAAoJEFBXWFqHsHzO8h8H+wTFJx+q4CF7Z8l+3OCR5rNQ
RSC3gaiYLhQUCEx+HVnvzDvhovdJNyoHiT6qdYqHIO5BYMmacsuWYwuZveaSePCl
WYZ0XkIuvMDZu4KFkl3ufEZx73u/7hbY1s4PevWm7KDeHY28XyWfflX0aW2yM/2Q
1Q/bNjMnsFGJPItBModiwS9lNjxMl7K9XBU47m0K/sJV4LFxbl+2OmfmaQYn4Ook
PAa4XbRH3d/Ff+jXrbwSy+AZZfpsiwDPV6cEwaAOTGr0O6+jKGRzqyAYNTANwjfU
ihUhy/XBjX2GRmGVxqTthDgktoSfX9eVQFU4WfDiHjRYO3y6vpBccC1ixpawUEM=
=iYpD
-----END PGP SIGNATURE-----
Merge tag 'imx-defconfig-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/defconfig
i.MX defconfig update for 5.4:
- Enable pinctrl and clock driver support for i.MX8MN SoC.
- Enable SDMA support for i.MX8MQ and i.MX8MM SoC, including
FW_LOADER_USER_HELPER and FW_LOADER_USER_HELPER_FALLBACK to support
SDMA firmware loading via udev.
- Enable module build of i.MX8 DDR PMU driver and ETNAVIV GPU driver.
- Enable module build of OV5645 camera driver in imx_v6_v7_defconfig.
* tag 'imx-defconfig-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: defconfig: CONFIG_DRM_ETNAVIV=m
ARM: imx_v6_v7_defconfig: Select the OV5645 camera driver
arm64: defconfig: Build imx8 ddr pmu as module
arm64: defconfig: Select CONFIG_CLK_IMX8MN by default
arm64: defconfig: Select CONFIG_PINCTRL_IMX8MN by default
arm64: defconfig: Enable SDMA on i.mx8mq/8mm
Link: https://lore.kernel.org/r/20190825153237.28829-7-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Enable the new AST2600 in multi_v7 and the aspeed_g5 configs.
- Regenerate defconfigs to drop old options
- Clean up network options
-----BEGIN PGP SIGNATURE-----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=XO1W
-----END PGP SIGNATURE-----
Merge tag 'aspeed-5.4-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into arm/defconfig
ASPEED defconfig updates for 5.4
- Enable the new AST2600 in multi_v7 and the aspeed_g5 configs.
- Regenerate defconfigs to drop old options
- Clean up network options
* tag 'aspeed-5.4-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: configs: aspeed_g5: Enable AST2600
ARM: configs: multi_v7: Add ASPEED G6
ARM: configs: aspeed: Refresh defconfigs
ARM: configs: aspeed: Enable commonly used network functionality
Link: https://lore.kernel.org/r/CACPK8XdyWzghA0QPDzA_MK5FYwhT5afqDJHNdhc8mfD2uk8MfQ@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Drop TV-OUT muxgroup from the HREF pin control
- Fix up BU21013 touchpad from Dmitry
- Split of AB8500 config in its own DTSI
- Drop the unused USB regulator config
- Add proper thermal zone for the CPU
-----BEGIN PGP SIGNATURE-----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=JGg5
-----END PGP SIGNATURE-----
Merge tag 'ux500-dts-v5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into arm/dt
More Ux500 device tree updates for the v5.4 kernel:
- Drop TV-OUT muxgroup from the HREF pin control
- Fix up BU21013 touchpad from Dmitry
- Split of AB8500 config in its own DTSI
- Drop the unused USB regulator config
- Add proper thermal zone for the CPU
* tag 'ux500-dts-v5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: dts: ux500: Update thermal zone
ARM: dts: ux500: Remove ab8500_ldo_usb regulator from device tree
ARM: dts: ux500: Move ab8500 nodes to ste-ab8500.dtsi
ARM: ux500: improve BU21013 touchpad bindings
ARM: dts: ux500: Drop TV-out muxgroup on HREFs
Link: https://lore.kernel.org/r/CACRpkdZ9Xvx+rg-hFVgG61_i2CdQSs+nZq5FXkkK2-3Ce9ooWg@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Disable the kirkwood RTC that doesn't work on the ts219 board
-----BEGIN PGP SIGNATURE-----
iFwEABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCXWZPAQAKCRALBhiOFHI7
1XDhAJiWiPskIJ8+YYuSzyf7N7ukmN8ZAJ4sz+nfLMBlC9YiOaAI+eFywZUHfQ==
=hvyg
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-5.4-1' of git://git.infradead.org/linux-mvebu into arm/dt
mvebu dt for 5.4 (part 1)
- Disable the kirkwood RTC that doesn't work on the ts219 board
* tag 'mvebu-dt-5.4-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: kirkwood: ts219: disable the SoC's RTC
Link: https://lore.kernel.org/r/878srdzjpj.fsf@FE-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- New board support: ZII i.MX7 RMU2, Kontron i.MX6UL N6310, and
PHYTEC phyBOARD-Segin based on i.MX6ULL.
- A series from Andrey Smirnov to update vf610-zii boards on I2C
pinmux, switch watchdog, GPIO expander IRQ.
- Move GIC node into soc node for i.MX6 SoCs.
- Add OV5645 camera support for imx6qdl-wandboard board.
- Drop unneeded snvs_pwrkey node for imx7d-zii-rpu2 and imx7-colibri.
- Use simple-mfd instead of simple-bus for i.MX6 ANATOP.
- Move the native-mode property inside the display-timings node for
various i.MX25 and i.MX27 boards.
- Add EDMA devices for i.MX7ULP SoC.
- A series from Stefan Riedmueller to update imx6ul-phytec-segin board
on various devices.
- Use OF graph to describe the display for opos6uldev board.
- Misc random updates on i.MX7/6 boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdYpwdAAoJEFBXWFqHsHzOpjMH/ArmJ/FlGDFmyffpXIT1qQdu
vyHdwySvCtftUsypDAhPSD43eFAOwqqfZR8b05UA+LE3TYKildxu4X2eEK2eFVn9
d97AEUuC49utHv9kf28kVPX0atI3QgqwJOW8/Xa1dlJl8CZN4GupmbLzYl9w6zF/
ii1WCzfnKjCQRW7s6+vFGqSdBnT1QXGSVXSYv5JI9MDh2qCzuYB1AI11CEnemYAq
pgJdTtdgW5g8sn8NHoAzQ9nUsq2IPkBHZzmt38eVk2YyvOmrMnpktNlBzMIBGaCJ
q6tmU7GaLrgcXe/lQMApBZ21jieAeKLWY+mdYN+kg1EumZHzllfitBZKYcL7mVs=
=DoYY
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm32 device tree changes for 5.4:
- New board support: ZII i.MX7 RMU2, Kontron i.MX6UL N6310, and
PHYTEC phyBOARD-Segin based on i.MX6ULL.
- A series from Andrey Smirnov to update vf610-zii boards on I2C
pinmux, switch watchdog, GPIO expander IRQ.
- Move GIC node into soc node for i.MX6 SoCs.
- Add OV5645 camera support for imx6qdl-wandboard board.
- Drop unneeded snvs_pwrkey node for imx7d-zii-rpu2 and imx7-colibri.
- Use simple-mfd instead of simple-bus for i.MX6 ANATOP.
- Move the native-mode property inside the display-timings node for
various i.MX25 and i.MX27 boards.
- Add EDMA devices for i.MX7ULP SoC.
- A series from Stefan Riedmueller to update imx6ul-phytec-segin board
on various devices.
- Use OF graph to describe the display for opos6uldev board.
- Misc random updates on i.MX7/6 boards.
* tag 'imx-dt-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (53 commits)
ARM: dts: vf610-zii-scu4-aib: Configure IRQ line for GPIO expander
ARM: dts: imx6ul-kontron-n6310: Add Kontron i.MX6UL N6310 SoM and boards
ARM: dts: vf610-zii-cfu1: Slow I2C0 down to 100 kHz
ARM: dts: pbab01: correct rtc vendor
ARM: vf610-zii-cfu1: Add node for switch watchdog
ARM: dts: imx6: drop gpmi-nand address and size cells
ARM: dts: imx6: replace simple-bus by simple-mfd for anatop
ARM: dts: imx6qdl-colibri: add phy to fec
ARM: dts: imx7-colibri: add recovery for I2C for iMX7
ARM: dts: imx7-colibri: Add sleep pinctrl to ethernet
ARM: dts: imx7-colibri: prepare module device tree for FlexCAN
ARM: dts: imx7-colibri: disable HS400
ARM: dts: imx7-colibri: make sure module supplies are always on
ARM: dts: imx7d: cl-som-imx7: add compatible for phy
ARM: dts: imx7d: cl-som-imx7: make ethernet work again
ARM: dts: imx6ul: Add csi node
ARM: dts: imx25: mbimxsd25: native-mode is part of display-timings
ARM: dts: apf27dev: native-mode is part of display-timings
ARM: dts: edb7211: native-mode is part of display-timings
ARM: dts: imx27-phytec-phycore-rdk: native-mode is part of display-timings
...
Link: https://lore.kernel.org/r/20190825153237.28829-5-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Remove regulator-boot-off properties that we never had in the mainline
kernel so they won't do anything. We add stdout-path for gta04, and
make am335x-boneblue use am335x-osd335x-common.dtsi file.
-----BEGIN PGP SIGNATURE-----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=Utq2
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.4/dt-take2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dt
dts changes for omap variants for v5.4
Remove regulator-boot-off properties that we never had in the mainline
kernel so they won't do anything. We add stdout-path for gta04, and
make am335x-boneblue use am335x-osd335x-common.dtsi file.
* tag 'omap-for-v5.4/dt-take2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-boneblue: Use of am335x-osd335x-common.dtsi
ARM: dts: gta04: define chosen/stdout-path
ARM: dts: omap3-n950-n9: Remove regulator-boot-off property
ARM: dts: am335x-cm-t335: Remove regulator-boot-off property
Link: https://lore.kernel.org/r/pull-1566599057-142651@atomide.com-2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Our usual pile of patches for the next release, which include mostly:
- More fixes thanks to the DT validation using the YAML bindings
- IR receiver support on the H6
- SPDIF support on the H6
- I2C Support on the H6
- CSI support on the A20
- RTC support on the H6
- New Boards: Lichee Zero Plus, Tanix TX6, A64-Olinuxino-eMMC
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXV/6JgAKCRDj7w1vZxhR
xc+VAQDjZWvNeMX75qsrz7Jbdy7jlbJJ/oDFBGx3C4clcTn7tgD6AsHeM760Pc6o
4a7G5DGcJakuFGsb1s4hNQOylmG3IQ4=
=pXxO
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Allwinner DT changes for 5.4
Our usual pile of patches for the next release, which include mostly:
- More fixes thanks to the DT validation using the YAML bindings
- IR receiver support on the H6
- SPDIF support on the H6
- I2C Support on the H6
- CSI support on the A20
- RTC support on the H6
- New Boards: Lichee Zero Plus, Tanix TX6, A64-Olinuxino-eMMC
* tag 'sunxi-dt-for-5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (40 commits)
arm64: dts: allwinner: orange-pi-3: Enable WiFi
ARM: dts: sunxi: Add missing watchdog clocks
ARM: dts: sunxi: Add missing watchdog interrupts
arm64: dts: allwinner: h6: Add support for RTC and fix the clock tree
ARM: dts: sun7i: Add CSI0 controller
arm64: dts: allwinner: a64: Add A64 OlinuXino board (with eMMC)
dt-bindings: arm: sunxi: Add compatible for A64 OlinuXino with eMMC
ARM: dts: v3s: Change the timers compatible
ARM: dts: h3: Change the timers compatible
ARM: dts: a83t: Change the timers compatible
ARM: dts: a23/a33: Change the timers compatible
ARM: dts: sun6i: Add missing timers interrupts
ARM: dts: sun5i: Add missing timers interrupts
ARM: dts: sun4i: Add missing timers interrupts
dt-bindings: mfd: Convert Allwinner GPADC bindings to a schema
arm64: dts: allwinner: h6: Introduce Tanix TX6 board
dt-bindings: arm: sunxi: Add compatible for Tanix TX6 board
arm64: allwinner: h6: add I2C nodes
dt-bindings: i2c: mv64xxx: Add compatible for the H6 i2c node.
ARM: dts: sunxi: Add mdio bus sub-node to GMAC
...
Link: https://lore.kernel.org/r/d97e6252-9dd7-4cf5-a3cf-56f78b0ca455.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Highlights
- odroid-c1: use MAC address from efuse
- add VDD_EE regulator to several boards
-----BEGIN PGP SIGNATURE-----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=zCaj
-----END PGP SIGNATURE-----
Merge tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/dt
ARM: dts: Amlogic updates for v5.4
Highlights
- odroid-c1: use MAC address from efuse
- add VDD_EE regulator to several boards
* tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson8b: odroidc1: use the MAC address stored in the eFuse
ARM: dts: meson8b: mxq: add the VDDEE regulator
ARM: dts: meson8b: odroidc1: add the VDDEE regulator
ARM: dts: meson8b: ec100: add the VDDEE regulator
ARM: dts: meson8b: add the PWM_D output pin
ARM: dts: meson8b: add ethernet fifo sizes
Link: https://lore.kernel.org/r/7hzhk3bi96.fsf@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
areas and also a 100ms speedup as a delay isn't needed anymore.
New boards are Tiger and Fievel from the Veyron family and the Mecer Xtreme
Mini S6, which I think is the first consumer-grade rk3229-based device in
the kernel.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAl1X/0cQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgT2RB/0X8SGcSRLL6vGCBH4vbATtnh1ceh6O2GA8
NO1N+OgQjPQWQyVx8ZWb7oaWgECwnXn41WT1HP9t0KB4w4sILZEswJrDRKV0dj1o
g+8tpgdxzJ7YF+vEkW1EcdPU2d1bRBJZ4qN38t2/StWg5WCrfThM2zBEUEJyWHpr
QYfSVXmhvPHISyZE+/k0tdgBhEi3KQph7ZVPhsmhugd1PeIV5lMDTVx4H7ljdnuC
/rVM/Yj+93r23bMgp6VGaMQmidlymYWCwxdTM4d4vDozViaykJ38BwDKVzfXX99y
hxA2BxKjp+37tuy4r4IO3kuqTEH6b4rvZzdNxJwBrGmIcBfv3n9j
=b567
-----END PGP SIGNATURE-----
Merge tag 'v5.4-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
A lot more love for Veyron devices with cleanups in the display and wifi
areas and also a 100ms speedup as a delay isn't needed anymore.
New boards are Tiger and Fievel from the Veyron family and the Mecer Xtreme
Mini S6, which I think is the first consumer-grade rk3229-based device in
the kernel.
* tag 'v5.4-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: add device tree for Mecer Xtreme Mini S6
Revert "ARM: dts: rockchip: add startup delay to rk3288-veyron panel-regulators"
ARM: dts: rockchip: Add pin names for rk3288-veyron fievel
ARM: dts: rockchip: A few fixes for veyron-{fievel,tiger}
ARM: dts: rockchip: Cleanup style around assignment operator
ARM: dts: rockchip: add veyron-tiger board
ARM: dts: rockchip: add veyron-fievel board
dt-bindings: ARM: dts: rockchip: Add bindings for rk3288-veyron-{fievel,tiger}
ARM: dts: rockchip: consolidate veyron panel and backlight settings
ARM: dts: rockchip: move rk3288-veryon display settings into a separate file
ARM: dts: rockchip: Limit WiFi TX power on rk3288-veyron-jerry
ARM: dts: rockchip: Specify rk3288-veyron-minnie's display timings
ARM: dts: rockchip: Specify rk3288-veyron-chromebook's display timings
Link: https://lore.kernel.org/r/1611583.rKl1eQBRh8@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
1. Add AHCI to Exynos5250,
2. Add camera and GPU power domains to Exynos5422,
3. Minor cleanup.
-----BEGIN PGP SIGNATURE-----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=HMId
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.4
1. Add AHCI to Exynos5250,
2. Add camera and GPU power domains to Exynos5422,
3. Minor cleanup.
* tag 'samsung-dt-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Add CAM power domain to Exynos5422/5800
ARM: dts: exynos: Add G3D power domain to Exynos542x
ARM: dts: exynos: Move MSC power domain to the right (sorted) place
ARM: dts: exynos: Add port map to Exynos5250 AHCI node
ARM: dts: exynos: Use space after '=' in exynos4412-itop-scp-core
Link: https://lore.kernel.org/r/20190816163042.6604-2-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The first change moves platform-specific asm-offsets.h to arch/arm/mach-omap2
to fix iessu with parallel build with CONFIG_IKHEADERS, and the second change
removes a useless kfree.
Note that the first change causes a trivial merge conflict with the iommu
changes for arch/arm/mach-omap2/Makefile.
-----BEGIN PGP SIGNATURE-----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=DRR4
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.4/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/soc
SoC changes for omap variants for v5.4
The first change moves platform-specific asm-offsets.h to arch/arm/mach-omap2
to fix iessu with parallel build with CONFIG_IKHEADERS, and the second change
removes a useless kfree.
Note that the first change causes a trivial merge conflict with the iommu
changes for arch/arm/mach-omap2/Makefile.
* tag 'omap-for-v5.4/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Delete an unnecessary kfree() call in omap_hsmmc_pdata_init()
ARM: OMAP2+: move platform-specific asm-offset.h to arch/arm/mach-omap2
Link: https://lore.kernel.org/r/pull-1567016893-318461@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- MAINTAINERS updates
- a generated headers parallel build fix
-----BEGIN PGP SIGNATURE-----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=pqcm
-----END PGP SIGNATURE-----
Merge tag 'at91-5.4-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/soc
AT91 SoC for 5.4
- MAINTAINERS updates
- a generated headers parallel build fix
* tag 'at91-5.4-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
mailmap: map old company name to new one @microchip.com
MAINTAINERS: at91: remove the TC entry
MAINTAINERS: at91: Collect all pinctrl/gpio drivers in same entry
ARM: at91: move platform-specific asm-offset.h to arch/arm/mach-at91
Link: https://lore.kernel.org/r/20190825203222.GA22800@piout.net
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Drop AR8031 PHY TX delay adjusting from i.MX7D machine code, as
it's superfluous due to the recent changes to Atheros AT803X driver.
- Select TIMER_IMX_SYS_CTR for arm64 ARCH_MXC platform, since the
system counter is needed as broadcast timer for cpuidle support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdYoI2AAoJEFBXWFqHsHzOxAsH/iKDF5cqmAOdNbD/0stFIxCV
ic+OX45aXyzbtSmD44sp0zuqGVA5RRu/OwYWlKA7WZHoeUUfbKMsMw9knO/ZaQTD
m9CwMuuA8bZhJUWSjbSpqlLJfdqzhnzkGuyq9A6IDqjf0y7eILD7km+YAZPNTBvo
LvvJnLhCI7FKY8miWpMe1pAY3XvzPTqlb1J0LywrJowXyVU9fJWVh7wSPTeDYsS1
+PQCTsnTX5Lm5rvV7px9ADwIzYq7qwuIVOfXwG+H1yMJRefQaWKePGb36KOHU+9S
isHiSYFSKw0BzLIGr2uap54LKaaprJiHdvUMncU8c3M+2hjWWNtlDkgZwUULluM=
=8VOJ
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/soc
i.MX SoC changes for 5.4:
- Drop AR8031 PHY TX delay adjusting from i.MX7D machine code, as
it's superfluous due to the recent changes to Atheros AT803X driver.
- Select TIMER_IMX_SYS_CTR for arm64 ARCH_MXC platform, since the
system counter is needed as broadcast timer for cpuidle support.
* tag 'imx-soc-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: stop adjusting ar8031 phy tx delay
arm64: Enable TIMER_IMX_SYS_CTR for ARCH_MXC platforms
Link: https://lore.kernel.org/r/20190825153237.28829-2-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds support for the new ASPEED AST2600 BMC SoC.
-----BEGIN PGP SIGNATURE-----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=KLEf
-----END PGP SIGNATURE-----
Merge tag 'aspeed-5.4-arch' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into arm/soc
ASPEED architecture updates for 5.4
This adds support for the new ASPEED AST2600 BMC SoC.
* tag 'aspeed-5.4-arch' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: aspeed: Enable SMP boot
ARM: aspeed: Add ASPEED AST2600 architecture
ARM: aspeed: Select timer in each SoC
dt-bindings: arm: cpus: Add ASPEED SMP
Link: https://lore.kernel.org/r/CACPK8Xc1aSp5fXL3cEzC9SJsCXG2JwsSPpQrW3a09dkvhCyHHA@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Single cleanup patch handling type checks using cppcheck tool
(bitwise shift by more than 31 on a 32 bit type)
-----BEGIN PGP SIGNATURE-----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=JqeJ
-----END PGP SIGNATURE-----
Merge tag 'vexpress-update-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/soc
ARMv7 Vexpress update for v5.4
Single cleanup patch handling type checks using cppcheck tool
(bitwise shift by more than 31 on a 32 bit type)
* tag 'vexpress-update-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
ARM: vexpress: Cleanup cppcheck shifting warning
Link: https://lore.kernel.org/r/20190814172441.26143-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Maxim 77802 PMIC is a main PMIC for the following Exynos5 based boards:
Odroid XU, Chromebook Pit and Chromebook Pi. Driver for its voltage
regulator is needed very early during boot to properly instantiate SD/MMC
devices and mount rootfs, so change that driver to be compiled-in.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Commit aff138bf8e ("ARM: dts: exynos: Add TMU nodes regulator supply
for Peach boards") assigned LDO10 to Exynos Thermal Measurement Unit,
but it turned out that it supplies also some other critical parts and
board freezes/crashes when it is turned off.
The mentioned commit made Exynos TMU a consumer of that regulator and in
typical case Exynos TMU driver keeps it enabled from early boot. However
there are such configurations (example is multi_v7_defconfig), in which
some of the regulators are compiled as modules and are not available
from early boot. In such case it may happen that LDO10 is turned off by
regulator core, because it has no consumers yet (in this case consumer
drivers cannot get it, because the supply regulators for it are not yet
available). This in turn causes the board to crash. This patch restores
'always-on' property for the LDO10 regulator.
Fixes: aff138bf8e ("ARM: dts: exynos: Add TMU nodes regulator supply for Peach boards")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Exynos3250 ADC has its own compatible because of differences from
other Exynos SoCs. Therefore it is not entirely compatible with
samsung,exynos-adc-v2. Remove the samsung,exynos-adc-v2.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The actual device name of the SPI controller being registered on EP93xx is
"spi0" (as seen by gpiod_find_lookup_table()). This patch fixes all
relevant lookup tables and the following failure (seen on EDB9302):
ep93xx-spi ep93xx-spi.0: failed to register SPI master
ep93xx-spi: probe of ep93xx-spi.0 failed with error -22
Fixes: 1dfbf334f1 ("spi: ep93xx: Convert to use CS GPIO descriptors")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Link: https://lore.kernel.org/r/20190831180402.10008-1-alexander.sverdlin@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that CONFIG_DRM_MSM is no longer default 'y' add it as a module to all
ARCH_QCOM enabled defconfigs to restore the previous expected build
behavior.
I split this off from the original patch to make this change unique to
the multi_v7_defconfig
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Now that CONFIG_DRM_MSM is no longer default 'y' add it as a module to all
ARCH_QCOM enabled defconfigs to restore the previous expected build
behavior.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
- A fix for update_sections_early() to cope with NULL ->mm pointers.
- A correction to the backtrace code to allow proper backtraces.
- Reinforcement of pfn_valid() with PFNs >= 4GiB.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ec12
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"Three fixes for ARM this time around:
- A fix for update_sections_early() to cope with NULL ->mm pointers.
- A correction to the backtrace code to allow proper backtraces.
- Reinforcement of pfn_valid() with PFNs >= 4GiB"
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8901/1: add a criteria for pfn_valid of arm
ARM: 8897/1: check stmfd instruction using right shift
ARM: 8874/1: mm: only adjust sections of valid mm structures
The majority of the fixes this time are for OMAP hardware,
here is a breakdown of the significant changes:
Various device tree bug fixes:
- TI am57xx boards need a voltage level fix to avoid damaging SD cards
- vf610-bk4 fails to detect its flash due to an incorrect description
- meson-g12a USB phy configuration fails
- meson-g12b reboot should not power off the SD card
- Some corrections for apparently harmless differences from the
documentation.
Regression fixes:
- ams-delta FIQ interrupts broke in 5.3
- TI am3/am4 mmc controllers broke in 5.2
The logic_pio driver (used on some Huawei ARM servers) needs a few
bug fixes for reliability.
A couple of compile-time warning fixes
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=mV+7
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"The majority of the fixes this time are for OMAP hardware, here is a
breakdown of the significant changes:
Various device tree bug fixes:
- TI am57xx boards need a voltage level fix to avoid damaging SD
cards
- vf610-bk4 fails to detect its flash due to an incorrect description
- meson-g12a USB phy configuration fails
- meson-g12b reboot should not power off the SD card
- Some corrections for apparently harmless differences from the
documentation.
Regression fixes:
- ams-delta FIQ interrupts broke in 5.3
- TI am3/am4 mmc controllers broke in 5.2
The logic_pio driver (used on some Huawei ARM servers) got a few bug
fixes for reliability.
And a couple of compile-time warning fixes"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (26 commits)
soc: ixp4xx: Protect IXP4xx SoC drivers by ARCH_IXP4XX || COMPILE_TEST
soc: ti: pm33xx: Make two symbols static
soc: ti: pm33xx: Fix static checker warnings
ARM: OMAP: dma: Mark expected switch fall-throughs
ARM: dts: Fix incomplete dts data for am3 and am4 mmc
bus: ti-sysc: Simplify cleanup upon failures in sysc_probe()
ARM: OMAP1: ams-delta-fiq: Fix missing irq_ack
ARM: dts: dra74x: Fix iodelay configuration for mmc3
ARM: dts: am335x: Fix UARTs length
ARM: OMAP2+: Fix omap4 errata warning on other SoCs
bus: hisi_lpc: Add .remove method to avoid driver unbind crash
bus: hisi_lpc: Unregister logical PIO range to avoid potential use-after-free
lib: logic_pio: Add logic_pio_unregister_range()
lib: logic_pio: Avoid possible overlap for unregistering regions
lib: logic_pio: Fix RCU usage
arm64: dts: amlogic: odroid-n2: keep SD card regulator always on
arm64: dts: meson-g12a-sei510: enable IR controller
arm64: dts: meson-g12a: add missing dwc2 phy-names
ARM: dts: vf610-bk4: Fix qspi node description
ARM: dts: Fix incorrect dcan register mapping for am3, am4 and dra7
...
On mmp3, there's an extra set of ICU registers (ICU2) that handle
interrupts on the extra cores. When masking off interrupts on MP1,
these should be masked as well.
We add a new interrupt controller via device tree to identify when we're
looking at an mmp3 machine via compatible field of "marvell,mmp3-intc".
[lkundrak@v3.sk: Changed "mrvl,mmp3-intc" compatible strings to
"marvell,mmp3-intc". Tidied up the subject line a bit.]
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20190822092643.593488-9-lkundrak@v3.sk
--
Changes since v1:
- Moved mmp3-specific mmp_icu2_base initialization from mmp_init_bases() to
mmp3_of_init() so that we don't have to check for marvell,mmp3-intc
compatibility twice.
- Drop an superfluous call to irq_set_default_host()
arch/arm/mach-mmp/regs-icu.h | 3 +++
drivers/irqchip/irq-mmp.c | 48 ++++++++++++++++++++++++++++++++++++
2 files changed, 51 insertions(+)
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20190822092643.593488-9-lkundrak@v3.sk
arch_dma_mmap_pgprot is used for two things:
1) to override the "normal" uncached page attributes for mapping
memory coherent to devices that can't snoop the CPU caches
2) to provide the special DMA_ATTR_WRITE_COMBINE semantics on older
arm systems and some mips platforms
Replace one with the pgprot_dmacoherent macro that is already provided
by arm and much simpler to use, and lift the DMA_ATTR_WRITE_COMBINE
handling to common code with an explicit arch opt-in.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> # m68k
Acked-by: Paul Burton <paul.burton@mips.com> # mips
The aurora cache on the Marvell Armada-XP SoC supports ECC protection
for the L2 data arrays. Add a "marvell,ecc-enable" device tree property
which can be used to enable this.
[jlu@pengutronix.de: use aurora specific define AURORA_ACR_ECC_EN]
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The aurora cache on the Marvell Armada-XP SoC supports the same tag
parity features as the other l2x0 cache implementations.
[jlu@pengutronix.de: use aurora specific define AURORA_ACR_PARITY_EN]
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
These defines will be used by subsequent patches to add support for the
parity check and error correction functionality in the Aurora L2 cache
controller.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The macro name is too generic, so add a AURORA_ prefix.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
This include file will be used by the AURORA EDAC code.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The stackframe setup when compiled with clang is different.
Since the stack unwinder expects the gcc stackframe setup it
fails to print backtraces. This patch adds support for the
clang stackframe setup.
Link: https://github.com/ClangBuiltLinux/linux/issues/35
Cc: clang-built-linux@googlegroups.com
Suggested-by: Tri Vo <trong@google.com>
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
pfn_valid can be wrong when parsing a invalid pfn whose phys address
exceeds BITS_PER_LONG as the MSB will be trimed when shifted.
The issue originally arise from bellowing call stack, which corresponding to
an access of the /proc/kpageflags from userspace with a invalid pfn parameter
and leads to kernel panic.
[46886.723249] c7 [<c031ff98>] (stable_page_flags) from [<c03203f8>]
[46886.723264] c7 [<c0320368>] (kpageflags_read) from [<c0312030>]
[46886.723280] c7 [<c0311fb0>] (proc_reg_read) from [<c02a6e6c>]
[46886.723290] c7 [<c02a6e24>] (__vfs_read) from [<c02a7018>]
[46886.723301] c7 [<c02a6f74>] (vfs_read) from [<c02a778c>]
[46886.723315] c7 [<c02a770c>] (SyS_pread64) from [<c0108620>]
(ret_fast_syscall+0x0/0x28)
Signed-off-by: Zhaoyang Huang <zhaoyang.huang@unisoc.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
After moving the DB8500 thermal driver to use device tree
we define the default thermal zone for the Ux500 in the
device tree replacing the oldstyle hardcoded trigger
points.
This default thermal zone utilizes the cpufreq driver
(using the generic OF cpufreq back-end) as a passive
cooling device, and defines a critical trip point when
the temperature goes above 85 degrees celsius which will
(hopefully) make the system shut down if the temperature
cannot be controlled.
This default policy can later be augmented for specific
subdevices if these have tighter temperature conditions.
After this patch we get:
/sys/class/thermal/thermal_zone0 (CPU thermal zone)
This reports the rough temperature and trip points
from the thermal zone in the device tree.
By executing two yes > /dev/null & jobs fully utilizing
the two CPU cores we can notice the temperature climbing
in the thermal zone in response and falling when we kill
the jobs.
/syc/class/thermal/cooling_device0 (cpufreq cooling)
this reports all 4 available cpufreq frequencies as
states.
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
