This patch will add separate function for refiring MFI commands in Fusion
adapters's OCR code.
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This patch will create separate functions for- 1) setting up IRQs for MSI-x
interrupts 2) setting up IRQs for legacy interrupts 3) freeing up IRQs. and
enable interrupts after adapter's initialization. The reason behind
initialising adapter earlier is: by that time firmware is operational and can
send interrupts, so better to use interrupt based interface to send internal
DCMD to firmware instead of using polling method, since MFI frames' pool size
is reduced and polling method does not free up MFI frame for fusion adapters,
so sending more DCMDs with polled method may cause MFI frames's pool go out of
frames and end up failing DCMD.
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
We only want to steer the I/O completion towards a queue, but don't
actually access any per-CPU data, so the raw_ version is fine to use
and avoids the warnings when using smp_processor_id().
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Andy Lutomirski <luto@kernel.org>
Tested-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Sumit Saxena <sumit.saxena@avagotech.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
struct fusion_context *fusion is already memset to '0', so remove a
redundant call to memmset "fusion->load_balance_info" to '0'.
Signed-off-by: Chaitra Basappa <chaitra.basappa@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
1) For fusion adapters, limit reserved frames for non SCSI commands to 8
(3 for parallel IOCTLs + 5 for driver's internal DCMDs).
Earlier reserved commands for non SCSI IO frames was set to 32, so with
this implementation, increased per controller "can_queue".
Behavior of MFI controllers will remain unchanged.
2) Optimize the code related to per controller's 'can_queue' setting.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Chaitra Basappa <chaitra.basappa@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Driver calls megasas_complete_cmd() to call wake_up() for each MFI frame
that was issued through the ioctl() interface prior to the kill adapter.
This ensures userspace ioctl() system calls issued just before a kill
adapter don't get stuck in wait state and IOCTLs are returned to
the application.
Cc: <stable@vger.kernel.org>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Chaitra Basappa <chaitra.basappa@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Update driver "mask_interrupts" before enable/disable hardware interrupt
in order to avoid missing interrupts because of "mask_interrupts" still
set to 1 and hardware interrupts are enabled.
Cc: <stable@vger.kernel.org>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Chaitra Basappa <chaitra.basappa@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch will address the issue of SCSI device created at OS level for
non existing VD. ldTgtIdtoLd[] array has size 256 for Extended VD firmware
and 128 for legacy firmware. Accessing indices beyond array size (OS will
send TUR, INQUIRY.. commands upto device index 255), may return valid LD
value and that particular SCSI command will be SUCCESS and creating SCSI
device for non existing target(VD).
For legacy firmware (64 VD firmware), invalidates LD (by setting LD value
to 0xff) in LdTgtIdtoLd[] array for device index beyond 127, so that
invalid LD(0xff) value should be returned beyond device index beyond 127.
Cc: <stable@vger.kernel.org>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch adds support for Secure Encrypting Drives (SED) in JBOD mode:
1) If the firmware supports SED JBOD, all non read/write commands to JBODs
will be sent via firmware path, and read/write commands to JBODs will
be sent via fastpath.
2) If the firmware does not support SED JBOD, driver will fall back to the
old design, i.e. send all JBOD I/O via fastpath.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Chaitra Basappa <chaitra.basappa@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch addresses below issues:
1) Few endianness bug fixes.
2) Break the iteration after (MAX_LOGICAL_DRIVES_EXT - 1)),
instead of MAX_LOGICAL_DRIVES_EXT.
3) Optimization in MFI INIT frame before firing.
4) MFI IO frame should be 256bytes aligned. Code is optimized to reduce
the size of frame for fusion adapters and make the MFI frame size
calculation a bit transparent and readable.
Cc: <stable@vger.kernel.org>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Chaitra Basappa <chaitra.basappa@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Drop the now unused reason argument from the ->change_queue_depth method.
Also add a return value to scsi_adjust_queue_depth, and rename it to
scsi_change_queue_depth now that it can be used as the default
->change_queue_depth implementation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
We won't ever queue more commands than the host allows. Instead of
letting drivers either reject or ignore this case handle it in
common code. Note that various driver use internal constant or
variables that are assigned to both shost->can_queue and checked
in ->change_queue_depth - I did remove those checks as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Do not process any SCSI and IOCTL command further (return them with
appropriate return values to callers), while driver removal is in
progress or PCI shutdown is invoked.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Corrected wait_event() call which was waiting for wrong completion
status (0xFF).
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In OCR(Online Controller Reset) path, driver sets adapter state to
MEGASAS_HBA_OPERATIONAL before getting new RAID map. There will be a small
window where IO will come from OS with old RAID map. This patch will update
adapter state to MEGASAS_HBA_OPERATIONAL, only after driver has new RAID
map to avoid any IOs getting build using old RAID map.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In OCR (Online Controller Reset) path, driver sets adapter state to
MEGASAS_HBA_OPERATIONAL before getting new RAID map. There will be a small
window where IO will come from OS with old RAID map. This patch will
update adapter state to MEGASAS_HBA_OPERATIONAL, only after driver has new
RAID map to avoid any IOs getting build using old RAID map.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Update MAINTAINERS list and copyright information for megaraid_sas driver.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Update driver version and remove some meta data (release date and extended
version) about megaraid_sas driver.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch fix spelling typo in printk and Kconfig within
various part of kernel sources.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove the tagged argument from scsi_adjust_queue_depth, and just let it
handle the queue depth. For most drivers those two are fairly separate,
given that most modern drivers don't care about the SCSI "tagged" status
of a command at all, and many old drivers allow queuing of multiple
untagged commands in the driver.
Instead we start out with the ->simple_tags flag set before calling
->slave_configure, which is how all drivers actually looking at
->simple_tags except for one worke anyway. The one other case looks
broken, but I've kept the behavior as-is for now.
Except for that we only change ->simple_tags from the ->change_queue_type,
and when rejecting a tag message in a single driver, so keeping this
churn out of scsi_adjust_queue_depth is a clear win.
Now that the usage of scsi_adjust_queue_depth is more obvious we can
also remove all the trivial instances in ->slave_alloc or ->slave_configure
that just set it to the cmd_per_lun default.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Function pci_enable_msix_range() may return negative values for error
conditions. So it's a bug by checking (pci_enable_msix_range() != 0)
for success and causes failure to megaraid driver when MSI is disabled.
[ 16.487267] megaraid_sas 0000:02:00.0: Controller type: iMR
[ 16.487275] genirq: Flags mismatch irq 0. 00000000 (megasas) vs. 00015a00 (tii
mer)
[ 16.487347] megasas: Failed to register IRQ for vector 0.
Fixes: 8ae80ed173 "megaraid: Use pci_enable_msix_range() instead of pci_enable_msix()"
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org> # 3.17
Resending the patch. Addressed the review comments by Tomas Henzl.
Driver version upgrade patch.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Resending the patch. Addressed the review comments from Tomas Henzl.
Added comment for to-do work.
Problem statement:
MFI link list in megaraid_sas driver is used from mfi-mpt pass-through commands.
This list can be corrupted due to many possible race conditions in driver and
eventually we may see kernel panic.
One example -
MFI frame is freed from calling process as driver send command via polling method and interrupt
for that command comes after driver free mfi frame (actually even after some other context reuse
the mfi frame). When driver receive MPT frame in ISR, driver will be using the index of MFI and
access that MFI frame and finally in-used MFI frame’s list will be corrupted.
High level description of new solution -
Free MFI and MPT command from same context.
Free both the command either from process (from where mfi-mpt pass-through was called) or from
ISR context. Do not split freeing of MFI and MPT, because it creates the race condition which
will do MFI/MPT list corruption.
Renamed the cmd_pool_lock which is used in instance as well as fusion with below name.
mfi_pool_lock and mpt_pool_lock to add more code readability.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Resending the patch. Addressed the review comments from Tomas Henzl.
Current driver does fast path read load balancing between arm and mirror disk
for two Drive Raid-1 configuration only.
Now, Driver support fast path read load balancing for all (any number of disk) Raid-1 configuration.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Resending the patch. Addressed the review comments from Tomas Henzl.
For certain deployment, we may need to disable irq cpu affinity hint.
This module parameter provides option for use to disable irq cpu affinity hint
and allow irqbalancer to handle the rest.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Resending the patch. Addressed the review comments from Tomas Henzl.
Round down the max sge to power of two.
Earlier max sge limit is 70 SGE, which will allow block layer to send 280K IO frame.
It is optimal to provide max IO size aligned to the smallest possible stripe size.
E.a
Consider that we have configured RAID Volumes which does not allow Fast Path across the stripe.
Raid volume with stripe size = 256K, will have peformance hit if we get io frame of size 280K.
Driver will not send IO frame large than stripe size to the Fast Path.
Also, FW will convert 280K frame into 256K + 24K. This is an additional overhead.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Resending the patch. Addressed the review comments from Tomas Henzl.
Megaraid_sas driver can now work in host lock less mode.
Remove host lock less as megaraid_sas driver will have safer access to raid map as described in earlier patch.
We now keep Driver Raid map copy, which will make sure
that driver will always have old or new map
Driver raid map will be replaced safely in MR_PopulateDrvRaidMap(), so there is no issue
even if IO is continue from the scsi mid layer.
There is a plan to remove "host_lock" and "hba_lock" usage from megaraid_sas in future.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Resending the patch. Addressed the review comments from Tomas Henzl.
reserved1 field(part of union) of Raid map struct was not required so it is removed.
Current MegaRAID firmware and hence the driver only supported 64VDs.
E.g: If the user wants to create more than 64VD on a controller,
it is not possible on current firmware/driver.
New feature and requirement to support upto 256VD, firmware/driver/apps need changes.
In addition to that there must be a backward compatibility of the new driver with the
older firmware and vice versa.
RAID map is the interface between Driver and FW to fetch all required
fields(attributes) for each Virtual Drives.
In the earlier design driver was using the FW copy of RAID map where as
in the new design the Driver will keep the RAID map copy of its own; on which
it will operate for any raid map access in fast path.
Local driver raid map copy will provide ease of access through out the code
and provide generic interface for future FW raid map changes.
For the backward compatibility driver will notify FW that it supports 256VD
to the FW in driver capability field.
Based on the controller properly returned by the FW, the Driver will know
whether it supports 256VD or not and will copy the RAID map accordingly.
At any given time, driver will always have old or new Raid map.
So with this changes, driver can also work in host lock less mode. Please
see next patch which enable host lock less mode for megaraid_sas driver.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Resending the patch. Addressed the review comments from Tomas Henzl.
Move buff_offset inside spinlock, corrected loop at crash dump buffer free,
reset_devices check is added to disable fw crash dump feature in kdump kernel.
This feature will provide similar interface as kernel crash dump feature.
When megaraid firmware encounter any crash, driver will collect the firmware raw image and
dump it into pre-configured location.
Driver will allocate two different segment of memory.
#1 Non-DMA able large buffer (will be allocated on demand) to capture actual FW crash dump.
#2 DMA buffer (persistence allocation) just to do a arbitrator job.
Firmware will keep writing Crash dump data in chucks of DMA buffer size into #2,
which will be copy back by driver to the host memory as described in #1.
Driver-Firmware interface:
==================
A.) Host driver can allocate maximum 512MB Host memory to store crash dump data.
This memory will be internal to the host and will not be exposed to the Firmware.
Driver may not be able to allocate 512 MB. In that case, driver will do possible memory
(available at run time) allocation to store crash dump data.
Let’s call this buffer as Host Crash Buffer.
Host Crash buffer will not be contigious as a whole, but it will have multiple chunk of contigious memory.
This will be internal to driver and firmware/application are unaware of it.
Partial allocation of Host Crash buffer may have valid information to debug depending upon
what was collected in that buffer and depending on nature of failure.
Complete Crash dump is the best case, but we do want to capture partial buffer just to grab something rather than nothing.
Host Crash buffer will be allocated only when FW Crash dump data is available,
and will be deallocated once application copy Host Crash buffer to the file.
Host Crash buffer size can be anything between 1MB to 512MB. (It will be multiple of 1MBs)
B.) Irrespective of underlying Firmware capability of crash dump support,
driver will allocate DMA buffer at start of the day for each MR controllers.
Let’s call this buffer as “DMA Crash Buffer”.
For this feature, size of DMA crash buffer will be 1MB.
(We will not gain much even if DMA buffer size is increased.)
C.) Driver will now read Controller Info sending existing dcmd “MR_DCMD_CTRL_GET_INFO”.
Driver should extract the information from ctrl info provided by firmware and
figure out if firmware support crash dump feature or not.
Driver will enable crash dump feature only if
“Firmware support Crash dump” +
“Driver was able to create DMA Crash Buffer”.
If either one from above is not set, Crash dump feature should be disable in driver.
Firmware will enable crash dump feature only if “Driver Send DCMD- MR_DCMD_SET_CRASH_BUF_PARA with MR_CRASH_BUF_TURN_ON”
Helper application/script should use sysfs parameter fw_crash_xxx to actually copy data from
host memory to the filesystem.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Resending the patch. Addressed the review comments from Tomas Henzl.
Current driver updates reply post host index to let firmware know that replies are processed,
while returning from ISR function, only if there is no oustanding replies in reply queue.
Driver will free the request frame immediately from ISR but reply post host index is not yet updated.
It means freed request can be used by submission path and there may be a tight loop in request/reply
path. In such condition, firmware may crash when it tries to post reply and there is no free
reply post descriptor.
Eventually two things needs to be change to avoid this issue.
Increase reply queue depth (double than request queue) to accommodate worst case scenario.
Update reply post host index to firmware once it reach to some pre-defined threshold value.
This change will make sure that firmware will always have some buffer of reply descriptor and
will never find empty reply descriptor in completion path.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Resending the patch. Addressed the review comments from Tomas Henzl.
Reduce the assingment for u64 req_data variable.
Use writeq() for 64bit PCI write instead of writel() to avoid additional lock overhead.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Resending the patch. Addressed the review comments from Tomas Henzl.
Current driver allow device scan for all the devices on channel 0 and 1.
E.a If we have two single drive raid volumes, we may see prints like below.
First two prints are for physical device which are used to form VD.
Prints like this creates confusion as it is really not required to scan any
hidden physical devices.
scsi1 : LSI SAS based MegaRAID driver
scsi 1:0:0:0: Direct-Access LSI MR9361-8i 4.21 PQ: 0 ANSI: 5
scsi 1:0:1:0: Direct-Access LSI MR9361-8i 4.21 PQ: 0 ANSI: 5
scsi 1:2:0:0: Direct-Access LSI MR9361-8i 4.21 PQ: 0 ANSI: 5
scsi 1:2:1:0: Direct-Access LSI MR9361-8i 4.21 PQ: 0 ANSI: 5
When slave_alloc called, sdev-type will not be set, so current code will always
return "0" in slave_alloc callback.
This patch make sure that driver return "-ENXIO" for non-syspd devices.
After this patch, we will see prints in syslog only for devices which are exposed.
For current example, below print will be available in syslog.
scsi1 : LSI SAS based MegaRAID driver
scsi 1:2:0:0: Direct-Access LSI MR9361-8i 4.21 PQ: 0 ANSI: 5
scsi 1:2:1:0: Direct-Access LSI MR9361-8i 4.21 PQ: 0 ANSI: 5
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The following patch for megaraid_sas updates the driver version and
Documentation/scsi/ChangeLog.megaraid_sas.
Signed-off-by: Adam Radford <aradford@gmail.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The following patch for megaraid_sas fixes a reset_mutex leak in megasas_reset_fusion().
Signed-off-by: Adam Radford <aradford@gmail.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The following patch for megaraid_sas removes some unused variables from the megasas_instance structure.
Signed-off-by: Adam Radford <aradford@gmail.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The following patch for megaraid_sas adds a missing initial call to
megasas_get_ld_vf_affiliation() at the end of megasas_probe_one().
Signed-off-by: Adam Radford <aradford@gmail.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The following patch for megaraid_sas fixes the LD/VF affiliation policy parsing
code to account for LD targetId's and Hidden LD's (not yet affiliated with any
Virtual Functions). This also breaks megasas_get_ld_vf_affiliation() into 2
separate functions: megasas_get_ld_vf_affiliation_111() and
megasas_get_ld_Vf_affiliation_12() to reduce indentation levels.
Signed-off-by: Adam Radford <aradford@gmail.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Kashyap Desai <Kashyap.desai@avagotech.com>
Cc: Neela Syam Kolli <megaraidlinux@lsi.com>
Cc: linux-scsi@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
Currently the driver fails to analize MSI-X re-enablement
status on resuming and always assumes the success. This
update checks the MSI-X initialization result and fails
to resume if MSI-Xs re-enablement failed.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Kashyap Desai <Kashyap.desai@avagotech.com>
Cc: Neela Syam Kolli <megaraidlinux@lsi.com>
Cc: linux-scsi@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
The SCSI standard defines 64-bit values for LUNs, and large arrays
employing large or hierarchical LUN numbers become more and more
common.
So update the linux SCSI stack to use 64-bit LUN numbers.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When the driver reads state values from the hw it might happen that
different values are read in subsequent reads and this can cause problems,
this may lead to a timeout in this function and a non working adapter.
Cc: Adam Radford <aradford@gmail.com>
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Shintaro Minemoto <fj3207hq@aa.jp.fujitsu.com>
Acked-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The following patch for megaraid_sas updates the driver version to
v06.803.01.00-rc1, and updates Documentation/scsi/ChangeLog.megaraid_sas.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The following patch for megaraid_sas adds Dell PowerEdge VRTS SR-IOV VF
support (Device ID 0x002f).
This patch has some > 80 column lines that need to be left in place
for code readability purposes.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
