Since commit [e58aa3d2: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler
returns with interrupts enabled (see commit [b738a50a:
genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reasons for the replacement:
The current driver for McPDM was developed to support the legacy mode only.
In preparation for the ABE support the current driver stack need the be
replaced.
The new driver is much simpler, easier to extend, and it also fixes some of the
issues with the old stack.
Main changes:
- single file for omap-mcpdm (mcpdm.c/h removed)
- Define names for registers, bits cleaned up, prefixed
- Full-duplex audio operation (arecord | aplay) has been fixed
- Less code
McPDM need to be turned off after all streams has been stopped.
This might cause pop noise on the output, if the codec's DAC is
still powered at this time.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order to probe, and operate correctly, the OMAP McPDM driver needs to
be converted to use hwmod.
The device name has been changed to probe the driver.
Replace the clk_* with pm_runtime_* calls to manage the clocks correctly.
Missing request_mem_region/release_mem_region added.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
DMA packet_size must be configured based on the McPDM FIFO threshold
value, number of channels.
Due to the FIFO operation the DMA muse be configured differently for
playback, and capture.
At the same time fix the McPDM threshold values used for playback, and
capture to avoid broken code.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The model_id is no longer needed within the platform_data
for the TPA driver since the model of TPA specified
with the device name (tpa6130a2/tpa6140a2).
Also update rx51 (the only affected user) to use the device name rather
than platform data.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the device name and driver_data to identify
the TPA model supported by the driver.
Board files should use either "tpa6130a2" or
"tpa6140a2" as device name to specify the model
in used on the specific board.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The orginal code does not cover the case that one DAI such as codec
may be shared between other two DAIs(CPU).
When do symmetry checking, altough the codec DAI requires symmetry,
the two CPU DAIs may still be configured to run on different rates.
We change to check each DAI's state separately instead of only checking
the dai link to prevent this issue.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reset the codec according to the Audio power-up delay errata for the 88PM8607.
Signed-off-by: Bas Vermeulen <bas.vermeulen@novero.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Introduce a I2S CLK supply so playback and capture can operate independently.
Signed-off-by: Bas Vermeulen <bas.vermeulen@novero.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is not used outside this driver so no need to make the symbol global.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is not used outside this driver so no need to make the symbol global.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is not used outside this driver so no need to make the symbol global.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is not used outside this driver so no need to make the symbol global.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 873bd4c (ASoC: Don't set invalid name string to snd_card->driver
field) broke generation of a driver name for all ASoC cards relying on the
automatic generation of one. Fix this by using the old default with spaces
replaced by underscores.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
The indentation is getting a little deep. Should be straight code motion,
no functional changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
One of the longest standing areas for improvement in ASoC has been the
DAPM algorithm - it repeats the same checks many times whenever it is run
and makes no effort to limit the areas of the graph it checks meaning we
do an awful lot of walks over the full graph. This has never mattered too
much as the size of the graph has generally been small in relation to the
size of the devices supported and the speed of CPUs but it is annoying.
In preparation for work on improving this insert a trace point after the
graph walk has been done. This gives us specific timing information for
the walk, and in order to give quantifiable (non-benchmark) numbers also
count every time we check a link or check the power for a widget and report
those numbers. Substantial changes in the algorithm may require tweaks to
the stats but they should be useful for simpler things.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since modern HDMI cards often have more than one output pin and thus
input device, we need to know which one has actually been plugged in.
This patch adds a name hint that indicates which PCM device is connected
to which pin.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Increase readability and understandability in the automute code.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The WM5100 is a highly integrated low power audio subsystem with advanced
digital signal processing capabilities including effects, speech clarity
enhancement and active noise cancellation. This initial driver provides
support for basic audio paths, further patches will provide more
complete functionality.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The driver assumes that control_data points to the drivers i2c_client struct,
but this is no longer the case since the ASoC core has switched to regmap.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Call platform_device_put() instead of platform_device_unregister() if
platform_device_add() fails.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This functionality is now subsumed within the bias management, using the
standard cache management functionality, without assuming the cache type.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
For digital only paths we need to make sure the bandgap is enabled prior
to starting the FLL which isn't tied into DAPM.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Add the PCM rule to allow disabling the PCM playback SRC.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the PCM rule to allow disabling the PCM playback SRC.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the PCM rules to allow disabling the PCM playback and capture SRCs.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a helper function to allow drivers to disable hardware resampling
when the application has specified the SNDRV_PCM_HW_PARAMS_NORESAMPLE
flag.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The installation of the minimum period size constraint in the PCM open
callbacks was not checked for errors. Add this check, and move the call
to the beginning of the function to avoid having to do any cleanups in
the error case.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
twl6040 supports 5 playback, and 2 capture channels
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Only mono audio can be used for vibra (DL4 channel).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reset the twl6040_reg array to hold the chip default values.
The only changed values were for the microphone input selection.
Select no input for the microphones in the twl6040_init_chip function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is no need to write to the vio registers at probe time, since most
them either read only, or shared with MFD or not used.
On the other hand it is a good idea to updated the ASICREV register in
the cache at this time.
After power up we need to restore some registers. Clean up the list to
contain only the registers we are going to restore.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
1. add different clkmux mode handling
SAIF can use two instances to implement full duplex (playback &
recording) and record saif may work on EXTMASTER mode which is
using other saif's BITCLK&LRCLK.
The clkmux mode could be set in pdata->init() in mach-specific code.
For generic saif driver, it only needs to know who is his master
and the master id is also provided in mach-specific code.
2. support playback and capture simutaneously however the sample
rates can not be different due to hw limitation.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8996 can measure the impedance of accessories connected to the
headphone output. Implement initial support for this, measuring the
left channel impedance when an accessory is detected and using this
to distinguish between a line load and a headphone load.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Rather than managing the bandgap in the bias level control use a supply
widget as we only actually need to enable it for analogue paths, not
fully digital ones.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
When the system has only the headphone and the line-out jacks without
speakers, the current auto-mute code doesn't work. It's because the
spec->automute_lines flag is wrongly referred in update_speakers().
This flag must be meaningless when spec->automute_hp_lo isn't set, thus
they should be always coupled.
The patch fixes the problem and add a comment to indicate the
relationship briefly.
BugLink: http://bugs.launchpad.net/bugs/851697
Reported-by: David Henningsson <david.henningsson@canonical.com>
Tested-By: Jayne Han <jayne.han@canonical.com>
Cc: stable@kernel.org (3.0)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The WM8776 supports a continuous range of sample rates rather than
discrete values and supports a wider range of sample rates on the
playback path than is currently supported. Update the constraints on
the DAIs to reflect this.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The i2c core will clear the clientdata pointer automatically,
we don't have to set the `data' field to NULL in remove() or
if probe() failed anymore.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The ambiguously named variable 'link' is used as a temporary throughout
davinci-pcm -- its presence makes grepping (and groking) the code
difficult.
Replace link with the value of link in almost all sites. The exception
is a couple places where the last-assigned link/chan needs to be
returned by a function -- in these cases, rename to last_link.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current method for machine driver to register with the ASoC core is to use
snd_soc_register_card() instead of creating a "soc-audio" platform device.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Reviewed-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current method for machine driver to register with the ASoC core is to
use snd_soc_register_card() instead of creating a "soc-audio" platform device.
In addition we use platform_device_register_simple() to create a platform
device for the codec. This function will handle putting and deleting the
device automatically which simplifies the error handling in the machine
driver.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Reviewed-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To get the PCM module loaded automatically by udev et al. we need to add a
proper MODULE_ALIAS.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Reviewed-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current method for machine driver to register with the ASoC core is to use
snd_soc_register_card() instead of creating a "soc-audio" platform device.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Reviewed-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_pcm_format_width() to determine the sample size, instead of
checking specify sample formats and assuming that those are the only
valid format.
This change adds support for big-endian architectures (which use the _BE
formats) and the packed 24-bit format (SNDRV_PCM_FORMAT_S24_3xE).
[Fixed single letter variable name legibility problem -- broonie]
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Roland UM-ONE midi usb interface differs from Roland UM-1.
Signed-off-by: Daniele Guerrieri <d.guerrieri@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We need to count the timeout down.
Reported-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Fix below build warning:
sound/soc/blackfin/bf5xx-ad73311.c: warning: initialization from incompatible pointer type
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
clk_get() returns a pointer to the struct clk or an ERR_PTR().
This patch also use PTR_ERR() for return value.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Freescale SSI audio controller supports "synchronous" and "asynchronous"
modes. In synchronous mode, playback and capture use the same input clock,
so sample rates must be the same during simultaneous playback and capture.
Unfortunately, the code which supports asynchronous mode is just broken in
various ways. In particular, it was constraining sample sizes as well as
the sample rate.
The fix also allows us to simplify the code by eliminating the 'asynchronous',
'playback', and 'capture' variables that were used to keep track of playback
and capture streams.
Unfortunately, it turns out that simulataneous playback and record does not
actually work on the only platform that supports asynchronous mode: the
Freescale P1022DS reference board. If a second stream is started, the SSI
grinds to halt for both streams. This is true even if the P1022 is configured
for synchronous mode, so it's likely a hardware problem that needs to be
worked around.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
wait_for_avail() in pcm_lib.c has a race in it (observed in practice by an
Intel validation group).
The function is supposed to return once space in the buffer has become
available, or if some timeout happens. The entity that creates space (irq
handler of sound driver and some such) will do a wake up on a waitqueue
that this function registers for.
However there are two races in the existing code
1) If space became available between the caller noticing there was no
space and this function actually sleeping, the wakeup is missed and the
timeout condition will happen instead
2) If a wakeup happened but not sufficient space became available, the
code will loop again and wait for more space. However, if the second
wake comes in prior to hitting the schedule_timeout_interruptible(), it
will be missed, and potentially you'll wait out until the timeout
happens.
The fix consists of using more careful setting of the current state (so
that if a wakeup happens in the main loop window, the schedule_timeout()
falls through) and by checking for available space prior to going into the
schedule_timeout() loop, but after being on the waitqueue and having the
state set to interruptible.
[tiwai: the following changes have been added to Arjan's original patch:
- merged akpm's fix for waitqueue adding order into a single patch
- reduction of duplicated code of avail check
]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
No code altered at this point, simply preparing for upcoming
refactorizations.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move code from endpoint.c into a new file called stream.c and rename
functions so that their names actually reflect what they're doing.
This way, endpoint.c will be available to functions that hold all the
endpoint logic.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sort its entries in alphabetical order.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes "Surround Speaker Playback Volume" being cut off.
(Commit b4dabfc452 was probably meant to fix this, but it fixed
only the "Switch" name, not the "Volume" name.)
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The AIF1 channels are numbered from zero than one; do the same thing for
AIF2 too.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The WM8996 only requires CPVDD when the charge pump is active so control
it separately to the other supplies, only enabling it when the charge pump
is active. This will result in a small power saving on systems which are
able to provide independent software control of the supply.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The semantics of snd_mpu401_uart_new()'s interrupt parameters are
somewhat counterintuitive: To prevent the function from allocating its
own interrupt, either the irq number must be invalid, or the irq_flags
parameter must be zero. At the same time, the irq parameter being
invalid specifies that the mpu401 code has to work without an interrupt
allocated by the caller. This implies that, if there is an interrupt
and it is allocated by the caller, the irq parameter must be set to
a valid-looking number which then isn't actually used.
With the removal of IRQF_DISABLED, zero becomes a valid irq_flags value,
which forces us to handle the parameters differently.
This patch introduces a new flag MPU401_INFO_IRQ_HOOK for when the
device interrupt is handled by the caller, and makes the allocation of
the interrupt to depend only on the irq parameter. As suggested by
Takashi, the irq_flags parameter was dropped because, when used, it had
the constant value IRQF_DISABLED.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recursive search of widget connections in snd_hda_get_conn_index()
must be terminated at the pin and the audio-out widgets. Otherwise
you'll get "too deep connection" warnings unnecessarily.
Reported-by: Francis Moreau <francis.moro@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A fix merged in 3.1-rc2 introduced a small regression, this should get it
to build again.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The i2c core will clear the clientdata pointer automatically.
We don't have to set the `data' field to NULL in remove() or
if probe() failed anymore.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The i2c core will clear the clientdata pointer automatically.
We don't have to set the `data' field to NULL in remove() or
if probe() failed anymore.
Also remove a unneeded NULL checking for kfree.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- use DAC0 instead of DAC1 for Port-A Headphone
- assign 0x03 to spec->multiout.hp_nid except model="6stack-dig-fp"
Signed-off-by: Raymond Yau <superquad.vortex2@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
YDSXGR_LEGACYOUTVOL is a Playback Volume control for OPL3 FM Synth.
Signed-off-by: Raymond Yau <superquad.vortex2@gmail.com>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Existing code only updates the audio delay when URBs were
submitted/retired. This can introduce an uncertainty of 8ms
on the number of samples played out with the default settings,
and a lot more when URBs convey more packets to reduce the
interrupt rate and power consumption.
This patch relies on the USB frame counter to reduce the
uncertainty to less than 2ms worst-case. The delay information
essentially becomes independent of the URB size and number of
packets. This should help applications like PulseAudio which
require accurate audio timing. Clemens Ladisch reported
a decrease of mplayer's A-V difference from nrpacks down to at
most 1ms.
Thanks to Clemens for also pointing out that the implementation
of frame counters varies between different HCDs. Only the
8 lowest-bits are used to estimate the delay.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
[clemens: changed debug code]
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently register read-back for the ad193x is broken, because it expects bit 0
of the upper byte to be set to indicate a read operation, while the regmap
default for SPI is to use bit 7.
This patch also addresses another oddity of the device. There are SPI and I2C
versions of this codec. In both cases the registers are 8-bit wide and numbered
from 0x0 to 0x10, but in the SPI case there is also a so called
'global address' which is prefixed in-front of the register address. The global
address mimics I2C behaviour and includes a static device address the and the
read/write flag. This basically extends the register address to an 16-bit value
numbered from 0x800 to 0x810. These are the register numbers which are
currently used by the driver. This works, because I2C will ignore the upper
8 bits of the register, but it is still a bit confusing, as there are no such
register numbers in the I2C case.
The approach taken by this patch is to number the registers from 0x00 to 0x10
and encode the global address for SPI mode into the read and write flag masks.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Return proper error instead of 0 if clk_get fails.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
snd_pcm_hw_constraint_integer() could return -1, in this case, sst platform is
not opened successfully. However the corresponding close callback isn't able
to be called later on to release these two allocated memories, thus resulting
in memory leak.
This patch moves the check for hardware contraints earlier, thus resolving this
issue.
Signed-off-by: Lu Guanqun <guanqun.lu@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the builtin snd_soc_set_runtime_hwparams() instead of assigning it by
myself.
Signed-off-by: Lu Guanqun <guanqun.lu@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Return -ENODEV instead of 0 if vendor id mismatch.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We don't use the step size so there's no need to work it out.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
We can directly read the FLL lock status on WM8996 so even if we don't
have an interrupt wired up we can still verify that the FLL started
successfully.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix the codec_name field of the dai_link to match the actual device name
of the codec. Otherwise the card won't be instantiated.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
We need to report the entire jack state to the core jack code, not just
the bits that were being updated by the caller, otherwise the status
reported by other detection methods will be omitted from the state seen
by userspace.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@kernel.org
In the case of no free channel available,
current implementation returns 0 instead of negative errno.
This patch fixes the logic to return -EINVAL if no free channel available.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Similarly to PLLs/FLLs some modern CODECs provide selectable system clock
sources. When the clock is the clock for a DAI we do not usually need to
identify which clock is being configured so can use clk_id for the source
clock but with CODEC wide system clocks we will need to specify both the
clock being configured and the source.
Add a source argument to the CODEC driver set_sysclk() operation to
reflect this. As this operation is not as widely used as the DAI
set_sysclk() operation the change is not very invasive. We probably
ought to go and make the same alternation for DAIs at some point.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fixes the following warning:
CC sound/soc/imx/imx-pcm-fiq.o
sound/soc/imx/imx-pcm-fiq.c: In function 'imx_pcm_fiq_new':
sound/soc/imx/imx-pcm-fiq.c:243: warning: unused variable 'card'
CC sound/soc/imx/imx-pcm-dma-mx2.o
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_codec_readable_register instead of open-coding it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently the condition for these WARN_ONs is reversed and they are placed
before the actual check whether we are going to write to that register. So if
the codec implements the register_writable callback we'll get a warning for each
writable register when syncing the register cache.
While we are at it change the check to use snd_soc_codec_writable_register
instead of open-coding it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Change the default return value of snd_soc_codec_{readable,writable}_register to
true when no codec specific callback for this function is given. Otherwise all
registers of that codec will neither be readable nor writable, which is most
certainly not what we want.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We have dapm_context instead of codec parameter.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Replace the channels_min check with a check for the relevant substream
being present. Suggested here [1] when mxs implemented the
audio-support.
[1] http://www.spinics.net/lists/arm-kernel/msg133010.html
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the channel is allocated as writecombine, then mmaping it should also
use writecombine. Also, add a proper device for the call. Ported from a
similar fix for mach-mxs.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
My first patch to ASoC ever! If I did something wrong, blame Ian.
Signed-off-by: Susan Gao <sgao@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Although the McASP supports sign-extending samples in RX or TX [1]; the
davinci-mcasp driver does not touch the {R,X}PBIT or {R,X}PAD field of the
{R,X}FMT registers meaning that the McASP will serialize the bytes it is given
regardless of their signedness. So supporting unsigned formats is as simple
as adding them to the metadata of the davinci-mcasp driver.
Update the FMTBITs reported in the snd_soc_dai_driver and also update the case
statements in davinci-mcasp's hw_params() function so that the McASP can be
connected to CODECs that use unsigned values.
[1] http://www.ti.com/lit/ug/sprufm1/sprufm1.pdf
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for Starr Labs USB MIDI devices such as the Z7S, which are
based on an FTDI serial UART chip.
Based on a patch by Daniel Mack.
Signed-off-by: Kristian Amlie <kristian@amlie.name>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PM QoS implementation files are better named
kernel/power/qos.c and include/linux/pm_qos.h.
The PM QoS support is compiled under the CONFIG_PM option.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: markgross <markgross@thegnar.org>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Headphones has stopped working for the original reported (a regression
compared to 2.6.38). This is because Speaker and Headphones share the
same DAC, in which case no Headphones volume control was created.
This patch fixes so that both Speaker and Headphones volume
controls are created in such scenario.
BugLink: http://bugs.launchpad.net/bugs/817943
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
'struct of_device' no longer exists, and its functionality has been merged
into platform_device. Update the MPC5200 audio DMA driver (mpc5200_dma)
accordingly. This fixes a build break.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
When the multi-io jacks are available, parse them first and assign DACs
before parsing speakers and headphones. This allows a better chance of
surround I/O in some desktops and laptops with limited DACs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit 23c09b0090
ALSA: hda - Support multiple speakers by Realtek auto-parser
changes the return value from alc_get_line_out_pfx(), and it breaks
the center/LFE mixer split check. The caller must test with a string
"CLFE" now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Introduce the pincfg table to patch_conexant.c for fixing up the extra
pin-configuration for auto-parser. As an example, Lenovo X200 model is
replaced with this new mechanism. (This also fixes the wrong mixer
elements for docking-station I/O in the previous model quirk
automagically.)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds Kconfig to support SMDK4212.
SMDK4212 is based on samsung exynos4212 SoC.
And WM8994 is used for audio codec.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Board file support for Ventana is not yet mainlined, and probably won't
ever be given the move to Device-Tree. Consequently, the Ventana entry
is being removed from arch/arm/tools/mach-types in the next merge window,
since it was registered over a year ago.
This will also remove function machine_is_ventana(), which is used by
the ASoC Tegra WM8903 machine driver. This will cause compilation
failures. Drop Ventana support to resolve this.
Hopefully, in the not-too-distant future, tegra_wm8903.c will be able to
configure itself from Device-Tree, and hence we'll be able to re-instate
Ventana support just by creating a .dts file for the board.
Also note that Aebl support is in a similar boat. However, that board
isn't scheduled for deprecation for at least another 5 months, and
perhaps we will have completely removed non-Device-Tree support from
tegra_wm8903.c by then and/or adjusted mach-types policy.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Joseph Pentland <jp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There are references in the code to 256 sources, so I tested it with 256 aplays,
of which the first and last with real data and the rest playing /dev/zero .
Also increase amount of page tables, so the default aplay size works.
Signed-off-by: Maarten Lankhorst <m.b.lankhorst@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Suppose the ALSA card already has a number of MAX_USER_CONTROLS controls, and
the user wants to replace one, it should not fail at this condition check.
Signed-off-by: Lu Guanqun <guanqun.lu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Similarly like ALC662 asus-mode* models, rewrite the laptop-amic and
dmic models with the static pin-config tables.
Now we can get rid of all alc269_quirks.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Re-implement the asus-mode[1-8] quirks with the pin-config tables.
They are provided in case where BIOS is broken on the device, so it's
not enabled in PCI SSID lookup table. User needs to specify it via model
option explicitly if the driver doesn't work with the BIOS setup as is.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For supporting both the multiple headphones and the multiple speakers,
add the new field in struct hda_multi_out, and evaluate in the standard
setup functions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Let's remove the rest of ALC861 and ALC861-VD quirks.
If any breakage is found, it can be fixed easily via the pin-config
table update.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
During the cleanup by commit 6727b12669,
the specific setups for dallas and hp models, using VREF50 for mic pins,
were lost. Fixed now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... and add a new bit-flags argument to specify the behavior of the
function. The older function is kept as is (as a wrapper).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When multiple headphones or speakers are assigned but no individual
DACs are available, the driver should take the first HP/SPK DAC instead
of another primary output. The patch adds a bit-flag to dac field of
struct pin_dac_pair indicating that it's a slave DAC.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The internal states, jack_present and line_jack_present should be
updated upon unsolicited events even if no automute is set.
Otherwise the wrong state is referred when the automute behavior is
changed by the mixer control.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the headphone or speaker output has no own DAC, initialize the path
using the primary DAC. Otherwise the path won't be set properly and
can result in the silence.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the test on pdev->id before the kzalloc to avoid requiring kfree when
the test fails. This fix was suggested by Wolfram Sang.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier x;
expression E1!=0,E2,E3,E4;
statement S;
iterator I;
@@
(
if (...) { ... when != kfree(x)
when != x = E3
when != E3 = x
* return ...;
}
... when != x = E2
when != I(...,x,...) S
if (...) { ... when != x = E4
kfree(x); ... return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Dong Aisheng <b29396@freescale.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Saif needs clear clk gate first before writing registers or the write
will not success.
The original xx_get_mclk function clear clk gate after mclk setting
that may cause the former mclk setting unwork, then the real output
mclk maybe inaccurate.
Placing the clear before setting mclk to avoid such an issue.
We also have to clear clk gate in startup instead of in prepare function.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The first change is to add an of_node_put, since codec_np has previously
been allocated. The rest of the patch reorganizes the error handling code
so the only code executed is that which is needed.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier x;
expression E1!=0,E2,E3,E4;
statement S;
iterator I;
@@
(
if (...) { ... when != of_node_put(x)
when != x = E3
when != E3 = x
* return ...;
}
... when != x = E2
when != I(...,x,...) S
if (...) { ... when != x = E4
of_node_put(x); ... return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
dma_channel_np has been accessed at this point, so decrease its reference
count before leaving the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier x;
expression E1!=0,E2,E3,E4;
statement S;
iterator I;
@@
(
if (...) { ... when != of_node_put(x)
when != x = E3
when != E3 = x
* return ...;
}
... when != x = E2
when != I(...,x,...) S
if (...) { ... when != x = E4
of_node_put(x); ... return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Introduce a new label that includes kfree and jump to that one.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier x;
expression E1!=0,E2,E3,E4;
statement S;
iterator I;
@@
(
if (...) { ... when != kfree(x)
when != x = E3
when != E3 = x
* return ...;
}
... when != x = E2
when != I(...,x,...) S
if (...) { ... when != x = E4
kfree(x); ... return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Alexander Sverdlin <subaparts@yandex.ru>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adjust the goto to jump to the error handling code that includes kfree.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier x;
expression E1!=0,E2,E3,E4;
statement S;
iterator I;
@@
(
if (...) { ... when != kfree(x)
when != x = E3
when != E3 = x
* return ...;
}
... when != x = E2
when != I(...,x,...) S
if (...) { ... when != x = E4
kfree(x); ... return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
GFP_ATOMIC is not needed here, use GFP_KERNEL instead.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
of_parse_phandle increments the reference count of np, so this should be
decremented before trying the next possibility.
Since we don't actually use np, we can decrement the reference count
immediately.
Reported-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If devices can unconditionally support idle_bias_off let them flag it in
their driver structure.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
In case we have a pending completion, for example due to a problem with
the input clock which got corrected after we timed out.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
This should never happen with level triggered IRQs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The WM8962 features a DSP providing a number of signal processing
features including HD Bass and Virtual Surround Sound (VSS). Enable
initial support for this, allowing users to enable and disable the
algorithms using the default coefficient sets. Further patches will
add support for runtime configuration of the DSP coefficients.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
We get called once per DAPM context but only need to run once. When DAPM
was serialized this was a series of noops but now it can run in parallel
we need to take proper care.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
This occurs frequently if we are in edge triggered mode as we must poll the
interrupt status register until we get no more interrupts so it's worth
the effort - it means we skip writing null acknowledgements to the chip.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
For non-audio uses like accessory detection we can use a lower quality,
unregulated microphone bias, saving a little power. As the hardware can
manually enable and disable the biases we can select regulating mode
automatically with supply widgets connected to the biases.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
There's no need for separate widgets for the enables (as the map already
shows).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Make AIFCLK supply the record paths otherwise record will not work unless
there is a simultaneous playback.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The label outnodev is only used when kzalloc has not yet taken place or has
failed, so there is no need for the call for kfree under this label.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier x;
expression E1!=0,E2,E3,E4;
statement S;
iterator I;
@@
(
if (...) { ... when != kfree(x)
when != x = E3
when != E3 = x
* return ...;
}
... when != x = E2
when != I(...,x,...) S
if (...) { ... when != x = E4
kfree(x); ... return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_hda_get_conn_index() returns a negative value while the current code
stores it in an unsigned int. It must be stored in a signed integer.
Reported-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently HD-audio driver shows the all error ELD byte as an error
in the kernel message. This is annoying when the video driver doesn't
set the correct ELD from the beginning. e.g. radeon sends a zero-byte
data, but we still check ELD with the fixed 128 byte as a workaround
for some broken devices, it spews 128-times errors.
For avoiding this, the driver aborts reading when the first byte is
invalid. In such a case, the whole data is certainly invalid.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch (as1482) adds a macro for testing whether or not a
pm_message value represents an autosuspend or autoresume (i.e., a
runtime PM) event. Encapsulating this notion seems preferable to
open-coding the test all over the place.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
In snd_hda_parse_pin_def_config(), we checked the associated number
of speaker pins and accepts only one number exclusively. But many BIOS
seem to give different assoc number for surround speakers, thus we'd
better to accept all speaker pins no matter which assoc number, and sort
like done for the headphone pins.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the support of multiple speakers by Realtek auto-parser.
When all speaker pins have individual DACs, create each speaker volume
control. Otherwise, create a bind-volume control for all speaker outs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the initial check of dB-range failed due to the read error, try to
check again at the later read, too. When an invalid dB range is found,
remove TLV flags and notify the mixer info change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent fix for testing dB range at the mixer creation time seems
to cause regressions in some devices. In such devices, reading the dB
info at probing time gives an error, thus both dBmin and dBmax are still
zero, and TLV flag isn't set although the later read of dB info succeeds.
This patch adds a workaround for such a case by assuming that the later
read will succeed. In future, a similar test should be performed in a
case where a wrong dB range is seen even in the later read.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
This patch includes below small fixes:
1. Move sta32x_set_bias_level() from sta32x_i2c_remove() to sta32x_remove().
2. Remove a redundant regulator_bulk_free() call in sta32x_i2c_remove(),
as we will call regulator_bulk_free() in sta32x_remove().
3. Remove unneeded snd_soc_codec_set_drvdata(codec, NULL) in sta32x_i2c_remove.
The i2c core will set the clientdata to NULL.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Johannes Stezenbach <js@sig21.net>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix "error: too few arguments to function 'ams_delta_set_bias_level'"
build errors in ams-delta.c that were introduced after commit d4c6005 ("ASoC:
Add context parameter to card DAPM callbacks") by adding dapm context
to ams_delta_set_bias_level calls.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The new parser may use "PCM" volume, but it was missing the vmaster
slave list, thus "Master" volume didn't control it.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=41342
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ASoC core tries to not enforce symmetric rates when
two streams open simultaneously. It does so by checking
rtd->rate being zero. This works exactly once after booting
because it is not set to zero again when the streams close.
Fix this by setting rtd->rate when no active stream is left.
[This leads to lots of warnings about not enforcing the symmetry in some
situations as there's a race in the userspace API where we know we've
got two applications but don't know what rates they want to set.
-- broonie ]
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The previous patch to fsl_dma.c ("fix initialization of DMA buffers")
left behind an unused local variable that causes a build warning.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The PowerPC Freescale SSI driver is claiming the IRQ when the IRQ when
the device is opened, which means that the /proc/interrupts entry for
the SSI exists only during playback or capture. This also meant that
the user won't know that the IRQ number is wrong until he tries to use
the device. Instead, we should claim the IRQ when the device is probed.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a machine driver to support the EVAL-ADAU1373 board connected to a
Analog Devices BF5XX evaluation board.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the Analog Devices ADAU1373 audio codec.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ALSA doesn't really have good mechanisms for dealing with these so we just
log them - the hardware already has automatic shutdown support.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure we have access to all the advanced DSP functinality offered by the
WM8962 by running the system clock at 512fs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Implement new fixup entries for Quanta FL1 and Fujitsu Lifebook
specific COEF and pin configurations. Removed the model entries
from alc269_quirks.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the duplicated creation of capture-mixer elements for some static
ALC268 configurations. The capture mixers must be put to cap_mixer field
instead of mixers array.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently it is only possible to route one source per switch into a mixer.
This patch modifies the code, so that it is possible to route multiple sources
into a mixer via the same switch. One use-case for this is routing a stereo
channel pair into a mono-mixer via the same switch.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pull control is availalbe for WM8994 AIF2, generally disabled as part of
the GPIO configuration in order to save power after system startup. As on
newer devices in the series there is no GPIO functionality on these pins
this will happen less naturally so have the driver disable the pulls as the
AIF is probed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is exactly one match or no match at all during the for loop iteration,
thus we can break from the for loop once a match is found.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove unused variable 'dai' to eliminate below warning.
CC sound/soc/nuc900/nuc900-pcm.o
sound/soc/nuc900/nuc900-pcm.c: In function 'nuc900_dma_new':
sound/soc/nuc900/nuc900-pcm.c:321: warning: unused variable 'dai'
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since commit b8c0dab9bf
"ASoC: core - PCM mutex per rtd",
the global pcm_mutex is not being used any more.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since commit aea170a099
"ASoC: soc-cache: Add reg_size as a member to snd_soc_codec",
the codec_drv pointer variable is not used in snd_soc_lzo_get_blksize.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since commit d779fce5d7
"ASoC: soc-cache: Ensure flat compression uses a copy of the defaults cache",
the codec_drv pointer variable is not used any more.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
asoc cache layer can't support this kind of spi registers well.
remove cache support and read/write registers directly
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[This will be used by the ad193x driver to fix the fact that the
original author of the driver put a bodge for their particular chip into
a the generic ASoC register I/O abstraction layer which looked like an
obvious bug which ended up getting fixed in 3.0. Sadly there were no
comments documenting what was going on. A minimally invasive correction
to the driver is to remove the register cache support and go direct to
the hardware all the time so we're adding a new feature -- broonie]
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
system clock is 24.576MHz instead of 12.288MHz
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
dac word len value should left shift before setting
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Acked-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
fix dac word len mask and adc tdm fmt shift value
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
request_any_context_irq() returns a negative value on failure.
On success, it returns either IRQC_IS_HARDIRQ or IRQC_IS_NESTED.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.orG
Refactoring the code using snd_pcm_hw_constraint_pow2() helper function.
Tested-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AES32 supports the non-standard 128kHZ, and this is enabled only when
SNDRV_PCM_RATE_KNOT is set in hw.rates field.
Tested-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On the Xonar Essence ST/STX, the connector J14 has been confirmed to be
a digital input, so enable it in the driver.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove a field that is not used at all. This remained from
earlier tests, but the current driver has decided not to handle
iris notifications.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC260 HP models work with the BIOS auto-parser. Let's cut them off.
Also move alc260_hp_master_*() to alc262_quirks.c as these are still
referred from there.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: https://bugs.launchpad.net/bugs/826081
The original reporter needs 'Headphone Jack Sense' enabled to have
audible audio, so add his PCI SSID to the whitelist.
Reported-and-tested-by: Muhammad Khurram Khan
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Newer RME cards like RayDAT and AIO support 32 samples per period. This
value is encoded as {1,1,1} in the HDSP_LatencyMask bits in the control
register.
Since {1,1,1} is also the representation for 8192 samples/period on
older RME cards, we have to special case 32 samples and 32768 bytes
according to the actual card.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, hdspm_decode_latency is called several times, violating the
DRY principle. Given that we need to distinguish between old and new
cards when decoding the latency bits in the control register, introduce
hdspm_get_latency() to provide the required functionality.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On newer RME cards like RayDAT and AIO, the 8192 samples per period size
are no longer supported. Instead, setting all three bits of
HDSP_LatencyMask to one ({1,1,1}) now corresponds to 32 samples per
period.
To make this more obvious to future developers, let's reorder the array
according to their bit representation, starting at 64 ({0,0,0}) up to
4096 ({1,1,0}) and finally 32 ({1,1,1}).
Note that this patch doesn't change semantics.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On newer RME cards like RayDAT and AIO, the lower bound is 32 samples
per period in contrast to 64 samples as seen on older cards.
We hence lower period_bytes_min to 32 * 4. Four bytes per sample.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Older RME cards like MADI and AES support period sizes of 8192 samples.
The original hdspm driver already featured this value, apparently, it
was lost during the rewrite.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The snd_usb_caiaq driver currently assumes that output urbs are serviced
in time and doesn't track when and whether they are given back by the
USB core. That usually works fine, but due to temporary limitations of
the XHCI stack, we faced that urbs were submitted more than once with
this approach.
As it's no good practice to fire and forget urbs anyway, this patch
introduces a proper bit mask to track which requests have been submitted
and given back.
That alone however doesn't make the driver work in case the host
controller is broken and doesn't give back urbs at all, and the output
stream will stop once all pre-allocated output urbs are consumed. But
it does prevent crashes of the controller stack in such cases.
See http://bugzilla.kernel.org/show_bug.cgi?id=40702 for more details.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-and-tested-by: Matej Laitl <matej@laitl.cz>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add linux/types.h to fix this compilation error:
In file included from arch/arm/mach-s3c2410/include/mach/gpio-fns.h:27:0,
from arch/arm/mach-s3c2410/include/mach/gpio.h:27,
from /home/anarsoul/work/pda-linux/linux-next/arch/arm/include/asm/gpio.h:5,
from include/linux/gpio.h:18,
from sound/soc/samsung/rx1950_uda1380.c:20:
arch/arm/plat-samsung/include/plat/gpio-cfg.h:29:34: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:30:34: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s5p_gpio_drvstr_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:57:2: error: expected specifier-qualifier-list before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:148:47: error: expected declaration specifiers or ‘...’ before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:156:24: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s3c_gpio_getpull’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:175:24: error: expected declaration specifiers or ‘...’ before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h: In function ‘s3c_gpio_cfgrange_nopull’:
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: error: ‘s3c_gpio_pull_t’ undeclared (first use in this function)
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: note: each undeclared identifier is reported only once for each function it appears in
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: error: expected ‘)’ before numeric constant
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: error: too many arguments to function ‘s3c_gpio_cfgall_range’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:174:12: note: declared here
arch/arm/plat-samsung/include/plat/gpio-cfg.h: At top level:
arch/arm/plat-samsung/include/plat/gpio-cfg.h:199:26: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s5p_gpio_get_drvstr’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:210:50: error: expected declaration specifiers or ‘...’ before ‘s5p_gpio_drvstr_t’
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add linux/types.h to fix this compilation error:
In file included from arch/arm/mach-s3c2410/include/mach/gpio-fns.h:27:0,
from arch/arm/mach-s3c2410/include/mach/gpio.h:27,
from /home/anarsoul/work/pda-linux/linux-next/arch/arm/include/asm/gpio.h:5,
from include/linux/gpio.h:18,
from sound/soc/samsung/rx1950_uda1380.c:20:
arch/arm/plat-samsung/include/plat/gpio-cfg.h:29:34: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:30:34: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s5p_gpio_drvstr_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:57:2: error: expected specifier-qualifier-list before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:148:47: error: expected declaration specifiers or ‘...’ before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:156:24: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s3c_gpio_getpull’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:175:24: error: expected declaration specifiers or ‘...’ before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h: In function ‘s3c_gpio_cfgrange_nopull’:
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: error: ‘s3c_gpio_pull_t’ undeclared (first use in this function)
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: note: each undeclared identifier is reported only once for each function it appears in
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: error: expected ‘)’ before numeric constant
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: error: too many arguments to function ‘s3c_gpio_cfgall_range’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:174:12: note: declared here
arch/arm/plat-samsung/include/plat/gpio-cfg.h: At top level:
arch/arm/plat-samsung/include/plat/gpio-cfg.h:199:26: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s5p_gpio_get_drvstr’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:210:50: error: expected declaration specifiers or ‘...’ before ‘s5p_gpio_drvstr_t’
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since we changed regmap to be selected and register per bus rather than
via the core only we can't rely on it being enabled by the ASoC core.
Support compiling it out.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reported-by: Axel Lin <axel.lin@gmail.com>
When the clocking registers are not overriden some of the registers are
not writable.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@kernel.org
On WM8994 class devices only the analogue portions of the CODEC require
VMID so when running digital only paths we can leave VMID disabled.
On some earlier devices the FLL uses VMID so we don't use DAPM reference
counting alone, we maintain an internal reference count which is also
enabled and disabled by the FLL startup.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Currently this does not actually do anything, it is being introduced in
order to facilitate additional power optimisations for current generation
devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
sound/soc/codecs/wm8750.c:784:2: warning: missing braces around initializer
sound/soc/codecs/wm8750.c:784:2: warning: (near initialization for ‘wm8750_spi_ids[2].name’)
It's because struct spi_device_id.name is a char array, not a pointer,
while the driver initializes explicitly with 0.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When CONFIG_REGMAP_I2C/SPI are m, CONFIG_REGMAP_I2C_MODULE is set in the
pre-processor instead of CONFIG_REGMAP_I2C. This removes SND_SOC_I2C as a
valid option for snd_soc_codec_set_cache_io()'s control parameter, and
causes any ASoC regmap-using codec built as a module to fail to initialize.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order to facilitate the widest range of use cases (especially things
like speakerphone) allow the headphone output to be enabled and disabled
by the application layer.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
My gmail account got disabled and I'm not going to reopen it.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The module device table for of_device_id should use "of" type.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
I2S in Exynos4 and S5PC110(S5PV210) has a internal dma.
It can be used low power audio mode and 2nd channel transfer.
This patch can support idma.
[Reapplied after dependencies propagated through in 3.1-rc1. --broonie]
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This error would have no effect on current silicon revisions, the fall
through case has the same behaviour.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
This fixes faulty outbount packets in case the inbound packets
received from the hardware are fragmented and contain bogus input
iso frames. The bug has been there for ages, but for some strange
reasons, it was only triggered by newer machines in 64bit mode.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-and-tested-by: William Light <wrl@illest.net>
Reported-by: Pedro Ribeiro <pedrib@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the case of "make da8xx_omapl_defconfig;make", the SPI support is disabled.
Thus calling regmap_init_spi in soc-io.c has below build error.
ERROR: "regmap_init_spi" [sound/soc/snd-soc-core.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
This patch fixes the build error by adding CONFIG_REGMAP_I2C/CONFIG_REGMAP_SPI
guards for regmap_init_i2c/regmap_init_spi.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
snd_azf3328_dbgcallenter is called at the very beginning of the function,
so it could be useful to call snd_azf3328_dbgcallleave at all exit points.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In commit 45eebda7, it add new function stac_vrefout_set, but it
is only used in code between CONFIG_SND_HDA_POWER_SAVE macro, so
add the macro to avoid such warning:
sound/pci/hda/patch_sigmatel.c:676:12: warning: 'stac_vrefout_set' defined but not used
Signed-off-by: Wang Shaoyan <wangshaoyan.pt@taobao.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
No meaningful runtime impact but is more in line with other CODECs and
will support further work.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
As we had no id_table only the driver name would be matched against
meaning that WM8987 devices wouldn't be bound.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The I2C address is misformatted and would never match.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@kernel.org
Without this, request_irq on subsequent device initialization fails, and
the codec cannot be used.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Two issues were preventing module snd-soc-tegra-wm8903.ko from being
removed and re-inserted:
a) The speaker-enable GPIO is hosted by the WM8903 chip. This GPIO must
be freed before snd_soc_unregister_card() is called, because that
triggers wm8903.c:wm8903_remove(), which calls gpiochip_remove(), which
then fails if any of the GPIOs are in use. To solve this, free all GPIOs
first, so the code doesn't care where they come from.
b) We need to call snd_soc_jack_free_gpios() to match the call to
snd_soc_jack_add_gpios() during initialization. Without this, the
call to snd_soc_jack_add_gpios() fails during any subsequent modprobe
and initialization, since the GPIO and IRQ are already registered. In
turn, this causes the headphone state not to be monitored, so the
headphone is assumed not to be plugged in, and the audio path to it is
never enabled.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: stable@kernel.org
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Not all PCM devices have all sub-streams. Specifically, the SPDIF driver
only supports playback and hence has no capture substream. Check whether
a substream exists before dereferencing it, when de-allocating DMA
buffers in tegra_pcm_deallocate_dma_buffer.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
sound/oss/pss.c: In function 'configure_nonsound_components':
sound/oss/pss.c:676: warning: 'check_region' is deprecated (declared at include/linux/ioport.h:201)
Signed-off-by: Wang Shaoyan <wangshaoyan.pt@taobao.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A slave-timer instance has no timer reference, and this results in
NULL-dereference at stopping the timer, typically called at closing
the device.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=40682
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow drivers to set up their own regmap API structures. This is mainly
useful with MFDs where the core driver will have set up regmap at the
minute, though it may make sense to push the existing regmap setup out
of the core into the drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Remove all the ASoC specific physical I/O code and replace it with calls
into the regmap API. The bulk write code can only be used safely if all
regmap calls are locked with the CODEC lock, we need to add bulk support
to the regmap API or replace the code with an open coded loop (though
currently it has no users...).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
This closes the small race between a status being read in response to an
interrupt and clearing the interrupt, meaning that if the status changes
between those periods we might not get a reassertion of the interrupt.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For marketing reasons the part will be called WM8996. In order to avoid
user confusion rename the driver to reflect this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Liam Girdwood <lrg@ti.com>
CONFIG_SND_TEA575X is enabled by RADIO_SF16FMR2, but the latter one is
no PCI device. Since tea575x-tuner itself is independent from the board
bus type, the config should be moved out of SND_PCI dependency.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use kzalloc rather than kmalloc followed by memset with 0
This considers some simple cases that are common and easy to validate
Note in particular that there are no ...s in the rule, so all of the
matched code has to be contiguous
The semantic patch that makes this output is available
in scripts/coccinelle/api/alloc/kzalloc-simple.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Purely cosmetic, but fixes the following build warning.
CC [M] sound/usb/quirks.o
sound/usb/quirks.c: In function ‘snd_usb_apply_boot_quirk’:
sound/usb/quirks.c:429:6: warning: ‘err’ may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sound/pci/hda/patch_via.c:2087: warning: 'dac' may be used uninitialized in this function
Signed-off-by: Wang Shaoyan <wangshaoyan.pt@taobao.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Put the exception checks for io_type switch() for possible mistakes in
future. Also this shuts up annoying compile warnings.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add new parameter to disable rounding of buffer/period sizes to
multiples of 128 bytes. This is more efficient in terms of memory
access but isn't required by the HDA spec and prevents users from
specifying exact period/buffer sizes. For example for 44.1kHz, a
period size set to 20ms will be rounded to 19.59ms.
Tested and enabled on Intel HDA controllers. Option is disabled by
default for other controllers.
Tested-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When creating the mixers for an USB audio device, the current code looks
at the host interface stored in mixer->chip->ctrl_if. Change this and
rather keep a local pointer to the interface that was given when
snd_usb_create_mixer() was called.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Nicolai Krakowiak <nicolai.krakowiak@gmail.com>
Reported-by: Lean-Yves LENHOF <jean-yves@lenhof.eu.org>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Focusrite Scarlett 18i6 USB has them that way, which is probably a
bug. Anyway, the driver should simply ignore this fact.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Nicolai Krakowiak <nicolai.krakowiak@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Update the PAS16 driver to use PIT_TICK_RATE instead
of the more generic CLOCK_TICK_RATE as the two are
equivalent on X86 and we want to depecrate the later.
Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It works fine with auto-parser and now the digital mic workaround was
implemented in auto-parser fixup, let's drop the static model quirks for
these models.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The digital-mic unit on ASUS Eee PC gives PDM signals instead of the
normal stereo PCM, thus you can't record a mono stream from the stereo
stream as is; the summed stereo signal results in almost zero level, and
you'll hear only soft noise.
As a workaround, use ALC269-specific COEF to manipulate the dmic route
for mono, like used for ALC271x. This is implemented as a fix-up, thus
it works only with model=auto or without REALTEK_QUIRKS Kconfig.
Reported-and-tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cache handling in this driver is broken. The chip has 16-bit registers, yet the
register numbers also increase by 2 per register, i.e. there are only
even-numbered registers. The cache in this driver, though, simply increments
register numbers, so it does need some mapping as seen in
sgtl5000_restore_regs(), note the '>> 1':
snd_soc_write(codec, SGTL5000_CHIP_LINREG_CTRL,
cache[SGTL5000_CHIP_LINREG_CTRL >> 1]);
That, of course, won't work with snd_soc_update_bits(). (Thus, we won't even
notice the missing register 0x1c in the default regs which shifted all follwing
registers to wrong values.) Noticed on the MX28EVK where enabling the regulators
simply locked up the chip.
Refactor the routines and use a properly sized default_regs array which matches
the register layout of the underlying chip, i.e. create a truly flat cache.
This also saves some code which should make up for the bigger array a little.
When soc-core will somewhen have another cache type which handles a step size,
this conversion will also ease the transition.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Dong Aisheng <b29396@freescale.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Avoids assigning possibly invalid address to pa, even if it
is never dereferenced.
Correct error response to reflect request object/function ids.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The WM1250-EV1 board has an ID chip on it, check the board ID and display
the board revision during startup.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Some devices can have performance optimized by setting different offsets
for left and right channels.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Later WM8994 devices implement a new DC servo readback mode with the
register used to access the offset moved to register 0x59. Implement
support for this and enable it on the appropriate devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
We leak the memory allocated to 'firmware' when we fail to
release_firmware() after a kmalloc() failure in hpi_dsp_code_open().
This patch should take care of the leak.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (430 commits)
[media] ir-mce_kbd-decoder: include module.h for its facilities
[media] ov5642: include module.h for its facilities
[media] em28xx: Fix DVB-C maxsize for em2884
[media] tda18271c2dd: Fix saw filter configuration for DVB-C @6MHz
[media] v4l: mt9v032: Fix Bayer pattern
[media] V4L: mt9m111: rewrite set_pixfmt
[media] V4L: mt9m111: fix missing return value check mt9m111_reg_clear
[media] V4L: initial driver for ov5642 CMOS sensor
[media] V4L: sh_mobile_ceu_camera: fix Oops when USERPTR mapping fails
[media] V4L: soc-camera: remove soc-camera bus and devices on it
[media] V4L: soc-camera: un-export the soc-camera bus
[media] V4L: sh_mobile_csi2: switch away from using the soc-camera bus notifier
[media] V4L: add media bus configuration subdev operations
[media] V4L: soc-camera: group struct field initialisations together
[media] V4L: soc-camera: remove now unused soc-camera specific PM hooks
[media] V4L: pxa-camera: switch to using standard PM hooks
[media] NetUP Dual DVB-T/C CI RF: force card hardware revision by module param
[media] Don't OOPS if videobuf_dvb_get_frontend return NULL
[media] NetUP Dual DVB-T/C CI RF: load firmware according card revision
[media] omap3isp: Support configurable HS/VS polarities
...
Fix up conflicts:
- arch/arm/mach-omap2/board-rx51-peripherals.c:
cleanup regulator supply definitions in mach-omap2
vs
OMAP3: RX-51: define vdds_csib regulator supply
- drivers/staging/tm6000/tm6000-alsa.c (trivial)
rtctimer.c uses interfaces from linux/module.h, so it should
include that file. This fixes build errors.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It adds device tree probe support for sgtl5000 driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This does not function correctly in all circumstances so disable the
periodic updates unconditionally for stable; a future patch will reenable
where appropriate.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Tested with the famous "hey, look! this compiles" test plan.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Acked by: Grant Likely <grant.likely@secretlab.ca>
552d1ef6b5 [ASoC: core - Optimise and refactor
pcm_new() to pass only rtd] breaks compilation of txx9aclc.c:
CC [M] sound/soc/txx9/txx9aclc.o
/home/ralf/src/linux/linux-mips/sound/soc/txx9/txx9aclc.c: In function 'txx9aclc_pcm_new':
/home/ralf/src/linux/linux-mips/sound/soc/txx9/txx9aclc.c:318:3: error: 'card' undeclared (first use in this function)
/home/ralf/src/linux/linux-mips/sound/soc/txx9/txx9aclc.c:318:3: note: each undeclared identifier is reported only once for each function it appears in
make[5]: *** [sound/soc/txx9/txx9aclc.o] Error 1
Fixed by providing a definition for card.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Apparently, there are multiple old firmware revisions in the wild for
the PCI RME MADI cards. Just add them to the list of supported devices
and treat them like their modern counterparts.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In slave mode, the card can only detect the base frequency (32..48kHz)
on the MADI link (exception: 96k frames), so the real external sample
rate is this base frequency multiplied by 1, 2 or 4 depending on the
speed mode.
This patch enables 64..192kHz sample rates in clock slave mode, which
failed before due to an alleged sample rate mismatch between the MADI
link (e.g., 48kHz) and the application in DS/QS mode (e.g., 96kHz,
192kHz).
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When running in slave mode (no clock master), there is no way to
determine the real wirespeed on the MADI link (single/double/quad
speed). Like physical gear, simply provide the user with a tristate
switch to select the appropriate format.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert array index from the loop bound to the loop index.
A simplified version of the semantic patch that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2,ar;
@@
for(e1 = 0; e1 < e2; e1++) { <...
ar[
- e2
+ e1
]
...> }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
sound: oss: rename local change_bits to avoid powerpc bitsops.h definition
ALSA: hda - Fix duplicated DAC assignments for Realtek
ALSA: asihpi - off by one in asihpi_hpi_ioctl()
ALSA: hda - Fix Oops with Realtek quirks with NULL adc_nids
ALSA: asihpi - bug fix pa use before init.
ALSA: hda - Add support for vref-out based mute LED control on IDT codecs
The driver only supports playback firstly.
For recording, as we have to use two saif instances to implement full
duplex (playback & recording) due to hardware limitation, we need to
figure out a good design to fit in ASoC.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove empty and useless g_input and s_input ioctls.
This fixes one fail of v4l2-compliance test.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change locking to allow tea575x-radio device to be opened multiple times.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert radio-sf16fmr2 to use generic TEA575x implementation. Most of the
driver code goes away as SF16-FMR2 is basically just a TEA5757 tuner
connected to ISA bus.
The card can optionally be equipped with PT2254A volume control (equivalent
of TC9154AP) - the volume setting is completely reworked (with balance control
added) and tested.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert tea575x-tuner to use the new V4L2 control framework. Also add
ext_init() callback that can be used by a card driver for additional
initialization right before registering the video device (for SF16-FMR2).
Also embed struct video_device to struct snd_tea575x to simplify the code.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
PCM_TX/RX are the same as SNDRV_PCM_STREAM_PLAYBACK/CAPTURE. Use
them directly.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The use of the "soc-audio" platform device is no longer en vogue,
update the code to the newer, simpler way of doing things.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The PSC audio drivers (psc-ac97/psc-i2s) register the DMA platform_device
on their own. This is frowned upon, from now on board code must
register a simple pcm dma platform device for each PSC with sound duties.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that an ASoC variant is available, tell users that this
driver is now living on borrowed time...
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a machine driver suitable for the AC97 part on the DB1000/DB1500/DB1100
boards.
Run-tested on DB1500.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This collides with powerpc exported functions from bitops.h. Rename the
local copy in the oss soundblaster mixer and ad1848 driver.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Copying hp_pins and speaker_pins from line_out_pins may confuse the
parser, and it can lead to duplicated initializations for the same pin
with a wrong DAC assignment. The problem appears in 3.0 kernel code.
Cc: <stable@kernel.org> (for 3.0)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
"adapter" is used as an array index in the adapters[] array so
the off by one would make us read past the end.
1c073b6797 "ALSA: asihpi - Remove spurious adapter index check"
reverted Dan Rosenberg's check that would have prevented the
overflow here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Somce quirk models don't set adc_nids but let the parser filling it.
But the recent code has unnecessary NULL-checks of spec->input_mux,
and it resulted in NULL dereferences.
This patch fixes that regression.
Reported-and-tested-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixes bug introduced by 1c073b67.
Also declare pa local to block in which it is used.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch also registers all necessary callbacks to support mute LED
only when such control is enabled. And it keeps codec AFG in D0 or D1
state all the time when aggressive power managemnt is enabled for vref-out
control (and mute LED) work correctly.
Signed-off-by: Vitaliy Kulikov <Vitaliy.Kulikov@idt.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
merge fchmod() and fchmodat() guts, kill ancient broken kludge
xfs: fix misspelled S_IS...()
xfs: get rid of open-coded S_ISREG(), etc.
vfs: document locking requirements for d_move, __d_move and d_materialise_unique
omfs: fix (mode & S_IFDIR) abuse
btrfs: S_ISREG(mode) is not mode & S_IFREG...
ima: fmode_t misspelled as mode_t...
pci-label.c: size_t misspelled as mode_t
jffs2: S_ISLNK(mode & S_IFMT) is pointless
snd_msnd ->mode is fmode_t, not mode_t
v9fs_iop_get_acl: get rid of unused variable
vfs: dont chain pipe/anon/socket on superblock s_inodes list
Documentation: Exporting: update description of d_splice_alias
fs: add missing unlock in default_llseek()
* 'next/devel2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (47 commits)
OMAP: Add debugfs node to show the summary of all clocks
OMAP2+: hwmod: Follow the recommended PRCM module enable sequence
OMAP2+: clock: allow per-SoC clock init code to prevent clockdomain calls from clock code
OMAP2+: clockdomain: Add per clkdm lock to prevent concurrent state programming
OMAP2+: PM: idle clkdms only if already in idle
OMAP2+: clockdomain: add clkdm_in_hwsup()
OMAP2+: clockdomain: Add 2 APIs to control clockdomain from hwmod framework
OMAP: clockdomain: Remove redundant call to pwrdm_wait_transition()
OMAP4: hwmod: Introduce the module control in hwmod control
OMAP4: cm: Add two new APIs for modulemode control
OMAP4: hwmod data: Add modulemode entry in omap_hwmod structure
OMAP4: hwmod data: Add PRM context register offset
OMAP4: prm: Remove deprecated functions
OMAP4: prm: Replace warm reset API with the offset based version
OMAP4: hwmod: Replace RSTCTRL absolute address with offset macros
OMAP: hwmod: Wait the idle status to be disabled
OMAP4: hwmod: Replace CLKCTRL absolute address with offset macros
OMAP2+: hwmod: Init clkdm field at boot time
OMAP4: hwmod data: Add clock domain attribute
OMAP4: clock data: Add missing divider selection for auxclks
...
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This update includes the changes necessary for supporting the
CS421x family of codecs. Previously this file only supported
the CS420x family of codecs.
This file also contains init verbs to correct several issues in
the CS421x hardware.
Behavior between the CS421x and CS420x codec families is similar,
so several functions have been reused with "if" statements to
determine which codec family (CS421x or CS420x) is present.
Also, this file will be updated sometime in the near future in
order to add support for a system using CS421x that requires
mono mix on the speaker output only.
[Fix const usages and adaption for new APIs by tiwai]
Signed-off-by: Tim Howe <tim.howe@cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The procedure for codec D-state change may have exceptional cases
depending on the codec chip, such as a longer delay or suppressing D3.
This patch adds a new codec ops, set_power_state() to override the system
default function. For ease of porting, snd_hda_codec_set_power_to_all()
helper function is extracted from the default set_power_state() function.
As an example, the Conexant codec-specific delay is removed from the
default routine but moved to patch_conexant.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new ops, post_suspend(), which is called after suspend() ops is
performed. This is called only in the case of the real PM suspend, and
the codec driver can use this for further changing of D-state or
clearing the LED, etc.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It makes little sense to enable power-saving without PM.
This removes SND_HDA_NEEDS_RESUME define so that we can use CONFIG_PM
in all places.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds ASoC support for the AC97 and I2S controllers
on the old Au1000/Au1500/Au1100 chips,
AC97 Tested on a Db1500. I2S untested since none of the boards
actually have an I2S codec wired up (just test pins).
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds checking of mute state on all outputs besides just
speakers to calculate the master mute state for mute led support.
It also renames and splits the function that does it for better code
clarity.
Signed-off-by: Vitaliy Kulikov <Vitaliy.Kulikov@idt.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Codec state is not restored immediately on resume but on the first
access when power-save is enabled. That leads to an invalid mute led
state after resume until either sound is played or some control is
changed. This patch adds a possibility for a vendor specific patch to
restore codec state immediately after resume if required. And it adds
code to restore IDT codecs state immediately on resume on HP systems
with mute led support.
Signed-off-by: Vitaliy Kulikov <Vitaliy.Kulikov@idt.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stream event debug can be noisy on larger audio devices so improve the
debug SNR by changing it to the verbose level.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In preparation for Dynamic PCM (AKA DSP) support.
This adds a callback function to be called at the completion of a DAPM stream
event.
This can be used by DSP components to perform calculations based on DAPM graphs
after completion of stream events.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
fs: take the ACL checks to common code
bury posix_acl_..._masq() variants
kill boilerplates around posix_acl_create_masq()
generic_acl: no need to clone acl just to push it to set_cached_acl()
kill boilerplate around posix_acl_chmod_masq()
reiserfs: cache negative ACLs for v1 stat format
xfs: cache negative ACLs if there is no attribute fork
9p: do no return 0 from ->check_acl without actually checking
vfs: move ACL cache lookup into generic code
CIFS: Fix oops while mounting with prefixpath
xfs: Fix wrong return value of xfs_file_aio_write
fix devtmpfs race
caam: don't pass bogus S_IFCHR to debugfs_create_...()
get rid of create_proc_entry() abuses - proc_mkdir() is there for purpose
asus-wmi: ->is_visible() can't return negative
fix jffs2 ACLs on big-endian with 16bit mode_t
9p: close ACL leaks
ocfs2_init_acl(): fix a leak
VFS : mount lock scalability for internal mounts
* 'next/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (35 commits)
ARM: msm: platsmp: determine number of CPU cores at boot time
ARM: Tegra: Seaboard: Fix I2C bus numbering for ADT7461
ARM: Tegra: Trimslice: Tri-state DAP3 pinmux
ARM: orion5x: fixup 5181 MPP mask check
ARM: mxs-dma: include <linux/dmaengine.h>
ARM: i.MX53: consistently use MX53_UART_PAD_CTRL for uart txd/rxd/rts/cts
ARM: i.MX53: UARTn_CTS pin should not change RTS input select
ARM: i.MX53: UARTn_TXD pin should not change RXD input select
ARM: mx25: Fix typo on CAN1_RX pad setting
iomux-mx53: add missing 'IOMUX_CONFIG_SION' for some I2C pad definitions
ARM: NUC93X: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: LPC32XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: CNS3XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: i.MX53: Fix IOMUX type o's
ARM i.MX dma: Fix burstsize settings
mach-mx5: fix the I2C clock parents
ARM: mxs/tx28: according to the TX28's datasheet D4-D7 are not used for MMC0
ARM i.MX23/28: platform-mxsfb: Add missing include of linux/dma-mapping.h
ARM: mx53: Fix some interrupts marked as reserved.
MXC: iomux-v3: correct NO_PAD_CTRL definition
...
Fix up trivial conflict in arch/arm/mach-imx/mach-mx31_3ds.c
This reverts commit d7c3e9525a as it does
not currently build due to missing dependencies in the Samsung tree.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Formatting a PCM name is useful for module debug too.
Add snd_prefix when making function public.
[minor coding-style fixes by tiwai]
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (297 commits)
ALSA: asihpi - Replace with snd_ctl_boolean_mono_info()
ALSA: asihpi - HPI version 4.08
ALSA: asihpi - Add volume mute controls
ALSA: asihpi - Control name updates
ALSA: asihpi - Use size_t for sizeof result
ALSA: asihpi - Explicitly include mutex.h
ALSA: asihpi - Add new node and message defines
ALSA: asihpi - Make local function static
ALSA: asihpi - Fix minor typos and spelling
ALSA: asihpi - Remove unused structures, macros and functions
ALSA: asihpi - Remove spurious adapter index check
ALSA: asihpi - Revise snd_pcm_debug_name, get rid of DEBUG_NAME macro
ALSA: asihpi - DSP code loader API now independent of OS
ALSA: asihpi - Remove controlex structs and associated special data transfer code
ALSA: asihpi - Increase request and response buffer sizes
ALSA: asihpi - Give more meaningful name to hpi request message type
ALSA: usb-audio - Add quirk for Roland / BOSS BR-800
ALSA: hda - Remove a superfluous argument of via_auto_init_output()
ALSA: hda - Fix indep-HP path (de-)activation for VT1708* codecs
ALSA: hda - Add documentation for codec-specific mixer controls
...
Fix a regression in the DAC filling code in patch_realtek.c. The already
filled DACs in multiout.dac_nids[] were ignored because of num_dacs=0,
thus always pointed to the first DAC.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'timers-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
mips: Fix i8253 clockevent fallout
i8253: Cleanup outb/inb magic
arm: Footbridge: Use common i8253 clockevent
mips: Use common i8253 clockevent
x86: Use common i8253 clockevent
i8253: Create common clockevent implementation
i8253: Export i8253_lock unconditionally
pcpskr: MIPS: Make config dependencies finer grained
pcspkr: Cleanup Kconfig dependencies
i8253: Move remaining content and delete asm/i8253.h
i8253: Consolidate definitions of PIT_LATCH
x86: i8253: Consolidate definitions of global_clock_event
i8253: Alpha, PowerPC: Remove unused asm/8253pit.h
alpha: i8253: Cleanup remaining users of i8253pit.h
i8253: Remove I8253_LOCK config
i8253: Make pcsp sound driver use the shared i8253_lock
i8253: Make pcspkr input driver use the shared i8253_lock
i8253: Consolidate all kernel definitions of i8253_lock
i8253: Unify all kernel declarations of i8253_lock
i8253: Create linux/i8253.h and use it in all 8253 related files
* 'spi/next' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
spi/imx: add device tree probe support
spi/imx: copy gpio number passed by platform data into driver private data
spi/imx: use soc name in spi device type naming scheme
spi/imx: merge type SPI_IMX_VER_0_7 into SPI_IMX_VER_0_4
spi/imx: do not use spi_imx2_3 to name SPI_IMX_VER_2_3 function and macro
spi/imx: use mx21 to name SPI_IMX_VER_0_0 function and macro
spi/imx: do not make copy of spi_imx_devtype_data
spi/dw: Add spi number into spi irq desc
spi/tegra: Use engineering names in DT compatible property
spi/fsl_spi: fix CPM spi driver
mach-s3c2410: remove unused spi-gpio.h file
spi: remove obsolete spi-s3c24xx-gpio driver
mach-gta2: remove unused spi-gpio.h include
mach-qt2410: convert to spi_gpio
mach-jive: convert to spi_gpio
spi/pxa2xx: Remove unavailable ssp_type from documentation
spi/bfin_spi: uninline fat queue funcs
spi/bfin_spi: constify pin array
spi/bfin_spi: use structs for accessing hardware regs
spi/topcliff-pch: Support new device ML7223 IOH
...
Fix up trivial conflict in arch/arm/mach-ep93xx/Makefile
HPI Version is used to check for firmware compatibility.
This version will accept 4.08.xx released firmware,
and will also accept 4.09.xx beta firmware
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add names corresponding to new HPI node types.
Shorten some names so that constructed names don't overflow the
maximum name length.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Because mutex is used in adapter struct defined here.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
