Currently udev does not know about the device being removed from the
file system. This may result in the situation where we're unable to
mount the file system by UUID or by LABEL because the by-uuid and
by-label links may still point to the device which is no longer part of
the btrfs file system and hence does not have any btrfs super block.
It can be easily reproduced by the following:
mkfs.btrfs -L bugfs /dev/loop[0-6]
mount /dev/loop0 /mnt/test
btrfs device delete /dev/loop0 /mnt/test
umount /mnt/test
mount LABEL=bugfs /mnt/test <---- this fails
then see:
ls -l /dev/disk/by-label/bugfs
which will still point to the /dev/loop0
We did not noticed this before because libblkid would send the udev
event for us when it notice that the link does not fit the reality,
however it does not do that anymore and completely relies on udev
information.
Fix this by sending the KOBJ_CHANGE event to the bdev kobject after
successful device removal.
Note that this does not affect device addition, because we will open the
device prior the addition from userspace and udev will notice that and
reread the device afterwards.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
This issue was detected by the "0-DAY kernel build testing".
fs/btrfs/volumes.c: In function 'btrfs_rm_device':
fs/btrfs/volumes.c:1505:1: warning: label 'error_close' defined but not used [-Wunused-label]
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Make the target disk of a running device replace operation
available for reading. This is only used as a last ressort for
the defect repair procedure. And it is dependent on the location
of the data block to read, because during an ongoing device
replace operation, the target drive is only partially filled
with the filesystem data.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
It is desirable to be able to configure the device replace
procedure to avoid reading the source drive (the one to be
copied) whenever possible. This is useful when the number of
read errors on this disk is high, because it would delay the
copy procedure alot. Therefore there is an option to avoid
reading from the source disk unless the repair procedure
really needs to access it. The regular read req asks for
mapping the block with mirror_num == 0, in this case the
source disk is avoided whenever possible. The repair code
selects the mirror_num explicitly (mirror_num != 0), this
case is not changed by this commit.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
During a running dev replace operation, all write requests to
the live filesystem are duplicated to also write to the target
drive. Therefore btrfs_map_block() is changed to duplicate
stripes that are written to the source disk of a device replace
procedure to be written to the target disk as well.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Before this commit, btrfs_map_block() was called with REQ_WRITE
in order to retrieve the list of mirrors for a disk block.
This needs to be changed for the device replace procedure since
it makes a difference whether you are asking for read mirrors
or for locations to write to.
GET_READ_MIRRORS is introduced as a new interface to call
btrfs_map_block().
In the current commit, the functionality is not yet changed,
only the interface for GET_READ_MIRRORS is introduced and all
the places that should use this new interface are adapted.
The reason that REQ_WRITE cannot be abused anymore to retrieve
a list of read mirrors is that during a running dev replace
operation all write requests to the live filesystem are
duplicated to also write to the target drive.
Keep in mind that the target disk is only partially a valid
copy of the source disk while the operation is ongoing. All
writes go to the target disk, but not all reads would return
valid data on the target disk. Therefore it is not possible
anymore to abuse a REQ_WRITE interface to find valid mirrors
for a REQ_READ.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
This commit contains all the essential changes to the core code
of Btrfs for support of the device replace procedure.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
This adds a new file to the sources together with the header file
and the changes to ioctl.h and ctree.h that are required by the
new C source file. Additionally, 4 new functions are added to
volume.c that deal with device creation and destruction.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
With the addition of the device replace procedure, it is possible
for btrfs_map_bio(READ) to report an error. This happens when the
specific mirror is requested which is located on the target disk,
and the copy operation has not yet copied this block. Hence the
block cannot be read and this error state is indicated by
returning EIO.
Some background information follows now. A new mirror is added
while the device replace procedure is running.
btrfs_get_num_copies() returns one more, and
btrfs_map_bio(GET_READ_MIRROR) adds one more mirror if a disk
location is involved that was already handled by the device
replace copy operation. The assigned mirror num is the highest
mirror number, e.g. the value 3 in case of RAID1.
If btrfs_map_bio() is invoked with mirror_num == 0 (i.e., select
any mirror), the copy on the target drive is never selected
because that disk shall be able to perform the write requests as
quickly as possible. The parallel execution of read requests would
only slow down the disk copy procedure. Second case is that
btrfs_map_bio() is called with mirror_num > 0. This is done from
the repair code only. In this case, the highest mirror num is
assigned to the target disk, since it is used last. And when this
mirror is not available because the copy procedure has not yet
handled this area, an error is returned. Everywhere in the code
the handling of such errors is added now.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
This patch adds some code to disallow operations on the device that
is used as the target for the device replace operation.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Btrfs admin operations that are manually started from user mode
and that cannot be executed at the same time return -EINPROGRESS.
A common way to enter and leave this locked section is introduced
since it used to be specific to the balance operation.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
A small number of functions that are used in a device replace
procedure when the operation is resumed at mount time are unable
to pass the same root pointer that would be used in the regular
(ioctl) context. And since the root pointer is not required, only
the fs_info is, the root pointer argument is replaced with the
fs_info pointer argument.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
This new function is used by the device replace procedure in
a later patch.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
This is required for the device replace procedure in a later step.
Two calling functions also had to be changed to have the fs_info
pointer: repair_io_failure() and scrub_setup_recheck_block().
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
This is required for the device replace procedure in a later step.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
The new function btrfs_find_device_missing_or_by_path() will be
used for the device replace procedure. This function itself calls
the second new function btrfs_find_device_by_path().
Unfortunately, it is not possible to currently make the rest of the
code use these functions as well, since all functions that look
similar at first view are all a little bit different in what they
are doing. But in the future, new code could benefit from these
two new functions, and currently, device replace uses them.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Some code to open block devices, to read the superblock and to
handle errors was repeated multiple times in 3 places, and the
following patch makes use of it as well. This code is now moved
into a subfunction.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Since we've kill the bigger one volume_mutex, we need to add devices
list mutex back.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Someone who is root or capable(CAP_SYS_ADMIN) could corrupt the
superblock and make Btrfs printk("%s") crash while holding the
uuid_mutex since nobody forces a limit on the string. Since the
uuid_mutex is significant, the system would be unusable
afterwards.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Reviewed-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Use WARN rather than printk followed by WARN_ON(1), for conciseness.
A simplified version of the semantic patch that makes this transformation
is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression list es;
@@
-printk(
+WARN(1,
es);
-WARN_ON(1);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Remove an invalid size check up from btrfs_shrink_dev().
The new size should not larger than the device->total_bytes as it was
already verified before coming to here(i.e. new_size < old_size).
Remove invalid check up for btrfs_shrink_dev().
Signed-off-by: Jie Liu <jeff.liu@oracle.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Alex reported a problem where we were writing between chunks on a rbd
device. The thing is we do bio_add_page using logical offsets, but the
physical offset may be different. So when we map the bio now check to see
if the bio is still ok with the physical offset, and if it is not split the
bio up and redo the bio_add_page with the physical sector. This fixes the
problem for Alex and doesn't affect performance in the normal case. Thanks,
Reported-and-tested-by: Alex Elder <elder@inktank.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
div_factor{_fine} has been implemented for two times, cleanup it.
And I move them into a independent file named math.h because they are
common math functions.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Steps to reproduce:
# mkfs.btrfs -m raid1 <disk1> <disk2>
# btrfstune -S 1 <disk1>
# mount <disk1> <mnt>
# btrfs device add <disk3> <disk4> <mnt>
# mount -o remount,rw <mnt>
# dd if=/dev/zero of=<mnt>/tmpfile bs=1M count=1
Deadlock happened.
It is because of the nested chunk allocation. When we wrote the data
into the filesystem, we would allocate the data chunk because there was
no data chunk in the filesystem. At the end of the data chunk allocation,
we should insert the metadata of the data chunk into the extent tree, but
there was no raid1 chunk, so we tried to lock the chunk allocation mutex to
allocate the new chunk, but we had held the mutex, the deadlock happened.
By rights, we would allocate the raid1 chunk when we added the second device
because the profile of the seed filesystem is raid1 and we had two devices.
But we didn't do that in fact. It is because the last step of the first device
insertion didn't commit the transaction. So when we added the second device,
we didn't cow the tree, and just inserted the relative metadata into the leaves
which were generated by the first device insertion, and its profile was dup.
So, I fix this problem by commiting the transaction at the end of the first
device insertion.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
So far the return code of barrier_all_devices() is ignored, which
means that errors are ignored. The result can be a corrupt
filesystem which is not consistent.
This commit adds code to evaluate the return code of
barrier_all_devices(). The normal btrfs_error() mechanism is used to
switch the filesystem into read-only mode when errors are detected.
In order to decide whether barrier_all_devices() should return
error or success, the number of disks that are allowed to fail the
barrier submission is calculated. This calculation accounts for the
worst RAID level of metadata, system and data. If single, dup or
RAID0 is in use, a single disk error is already considered to be
fatal. Otherwise a single disk error is tolerated.
The calculation of the number of disks that are tolerated to fail
the barrier operation is performed when the filesystem gets mounted,
when a balance operation is started and finished, and when devices
are added or removed.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Call btrfs_abort_transaction as early as possible when an error
condition is detected, that way the line number reported is useful
and we're not clueless anymore which error path led to the abort.
Signed-off-by: David Sterba <dsterba@suse.cz>
Pull btrfs fixes from Chris Mason:
"I've split out the big send/receive update from my last pull request
and now have just the fixes in my for-linus branch. The send/recv
branch will wander over to linux-next shortly though.
The largest patches in this pull are Josef's patches to fix DIO
locking problems and his patch to fix a crash during balance. They
are both well tested.
The rest are smaller fixes that we've had queued. The last rc came
out while I was hacking new and exciting ways to recover from a
misplaced rm -rf on my dev box, so these missed rc3."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (25 commits)
Btrfs: fix that repair code is spuriously executed for transid failures
Btrfs: fix ordered extent leak when failing to start a transaction
Btrfs: fix a dio write regression
Btrfs: fix deadlock with freeze and sync V2
Btrfs: revert checksum error statistic which can cause a BUG()
Btrfs: remove superblock writing after fatal error
Btrfs: allow delayed refs to be merged
Btrfs: fix enospc problems when deleting a subvol
Btrfs: fix wrong mtime and ctime when creating snapshots
Btrfs: fix race in run_clustered_refs
Btrfs: don't run __tree_mod_log_free_eb on leaves
Btrfs: increase the size of the free space cache
Btrfs: barrier before waitqueue_active
Btrfs: fix deadlock in wait_for_more_refs
btrfs: fix second lock in btrfs_delete_delayed_items()
Btrfs: don't allocate a seperate csums array for direct reads
Btrfs: do not strdup non existent strings
Btrfs: do not use missing devices when showing devname
Btrfs: fix that error value is changed by mistake
Btrfs: lock extents as we map them in DIO
...
Commit 442a4f6308 added btrfs device
statistic counters for detected IO and checksum errors to Linux 3.5.
The statistic part that counts checksum errors in
end_bio_extent_readpage() can cause a BUG() in a subfunction:
"kernel BUG at fs/btrfs/volumes.c:3762!"
That part is reverted with the current patch.
However, the counting of checksum errors in the scrub context remains
active, and the counting of detected IO errors (read, write or flush
errors) in all contexts remains active.
Cc: stable <stable@vger.kernel.org> # 3.5
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
We need a barrir before calling waitqueue_active otherwise we will miss
wakeups. So in places that do atomic_dec(); then atomic_read() use
atomic_dec_return() which imply a memory barrier (see memory-barriers.txt)
and then add an explicit memory barrier everywhere else that need them.
Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
When we close devices we add back empty devices for some reason that escapes
me. In the case of a missing dev we don't allocate an rcu_string for it's
name, so check to see if the device has a name and if it doesn't don't
bother strdup()'ing it. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
The '->write_super' superblock method is gone, and this patch removes all the
references to 'write_super' from btrfs.
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: linux-btrfs@vger.kernel.org
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Code is added to suppress the I/O stats printing at mount time if all
statistic values are zero.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
People complained about the annoying kernel log message
"btrfs: no dev_stats entry found ... (OK on first mount after mkfs)"
everytime a filesystem is mounted for the first time after running
mkfs. Since the distribution of the btrfs-progs is not synchronized
to the kernel version, mkfs like it is now will be used also in the
future. Then this message is not useful to find errors, it is just
annoying. This commit removes the printk().
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
This will be used in conjunction with btrfs device ready <dev>. This is
needed for initrd's to have a nice and lightweight way to tell if all of the
devices needed for a file system are in the cache currently. This keeps
them from having to do mount+sleep loops waiting for devices to show up.
Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Commit c11d2c236c (Btrfs: add ioctl to get and reset the device
stats) introduced two ioctls doing almost the same thing distinguished
by just the ioctl number which encodes "do reset after read". I have
suggested
http://www.mail-archive.com/linux-btrfs@vger.kernel.org/msg16604.html
to implement it via the ioctl args. This hasn't happen, and I think we
should use a more clean way to pass flags and should not waste ioctl
numbers.
CC: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: David Sterba <dsterba@suse.cz>
This introduces btrfs_resume_balance_async(), which, given that
restriper state was recovered earlier by btrfs_recover_balance(),
resumes balance in btrfs-balance kthread.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Fix a bug that triggered asserts in btrfs_balance() in both normal and
resume modes -- restriper state was not properly restored on read-only
mounts. This factors out resuming code from btrfs_restore_balance(),
which is now also called earlier in the mount sequence to avoid the
problem of some early writes getting the old profile.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
It is normal behaviour of the low level btrfs function btrfs_map_bio()
to complete a bio with -EIO if the device is missing, instead of just
preventing the bio creation in an earlier step.
This used to cause I/O statistic read error increments and annoying
printk_ratelimited messages. This commit fixes the issue.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Reported-by: Carey Underwood <cwillu@cwillu.com>
Al pointed out that we can just toss out the old name on a device and add a
new one arbitrarily, so anybody who uses device->name in printk could
possibly use free'd memory. Instead of adding locking around all of this he
suggested doing it with RCU, so I've introduced a struct rcu_string that
does just that and have gone through and protected all accesses to
device->name that aren't under the uuid_mutex with rcu_read_lock(). This
protects us and I will use it for dealing with removing the device that we
used to mount the file system in a later patch. Thanks,
Reviewed-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Josef Bacik <josef@redhat.com>
The device statistics are written into the device tree with each
transaction commit. Only modified statistics are written.
When a filesystem is mounted, the device statistics for each involved
device are read from the device tree and used to initialize the
counters.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
An ioctl interface is added to get the device statistic counters.
A second ioctl is added to atomically get and reset these counters.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
The goal is to detect when drives start to get an increased error rate,
when drives should be replaced soon. Therefore statistic counters are
added that count IO errors (read, write and flush). Additionally, the
software detected errors like checksum errors and corrupted blocks are
counted.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Reproduce:
$ mkfs.btrfs /dev/sdb7
$ mount /dev/sdb7 /mnt/btrfs -o ro
$ btrfs dev add /dev/sdb8 /mnt/btrfs
ERROR: error adding the device '/dev/sdb8' - Invalid argument
Since we mount with readonly options, and /dev/sdb7 is not a seeding one,
a readonly notification is preferred.
Signed-off-by: Liu Bo <liubo2009@cn.fujitsu.com>
Reviewed-by: Josef Bacik <josef@redhat.com>
btrfs_map_block sets mirror_num, so that the repair code knows eventually
which device gave us the read error. For RAID10, mirror_num must be 1 or 2.
Before this fix mirror_num was incorrectly related to our stripe index.
Signed-off-by: Jan Schmidt <list.btrfs@jan-o-sch.net>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Fix a bug, where in case we need to adjust stripe_size so that the
length of the resulting chunk is less than or equal to max_chunk_size,
DUP chunks turn out to be only half as big as they could be.
Cc: Arne Jansen <sensille@gmx.net>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
We miscalculate the length of extents we're discarding, and it leads to
an eof of device.
Reported-by: Daniel Blueman <daniel@quora.org>
Signed-off-by: Liu Bo <liubo2009@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Btrfs puts the filesystem metadata into its own address space, and
somehow the block device address space isn't getting onto disk properly
before a mount. The end result is that a loop of mkfs and mounting the
filesystem will sometimes find stale or incorrect data.
This commit should fix it by sprinkling fdatawrites and invalidate_bdev
calls around. This is a short term measure to make sure it is fixed.
The block devices really should be flushed and cleaned up higher in the
stack.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
