Minor conflict, a CHECK was placed into an if() statement
in net-next, whilst a newline was added to that CHECK
call in 'net'. Thanks to Daniel for the merge resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since LD_ABS/LD_IND instructions are now removed from the core and
reimplemented through a combination of inlined BPF instructions and
a slow-path helper, we can get rid of the complexity from x32 JIT.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Since LD_ABS/LD_IND instructions are now removed from the core and
reimplemented through a combination of inlined BPF instructions and
a slow-path helper, we can get rid of the complexity from x64 JIT.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The JIT compiler emits ia32 bit instructions. Currently, It supports eBPF
only. Classic BPF is supported because of the conversion by BPF core.
Almost all instructions from eBPF ISA supported except the following:
BPF_ALU64 | BPF_DIV | BPF_K
BPF_ALU64 | BPF_DIV | BPF_X
BPF_ALU64 | BPF_MOD | BPF_K
BPF_ALU64 | BPF_MOD | BPF_X
BPF_STX | BPF_XADD | BPF_W
BPF_STX | BPF_XADD | BPF_DW
It doesn't support BPF_JMP|BPF_CALL with BPF_PSEUDO_CALL at the moment.
IA32 has few general purpose registers, EAX|EDX|ECX|EBX|ESI|EDI. I use
EAX|EDX|ECX|EBX as temporary registers to simulate instructions in eBPF
ISA, and allocate ESI|EDI to BPF_REG_AX for constant blinding, all others
eBPF registers, R0-R10, are simulated through scratch space on stack.
The reasons behind the hardware registers allocation policy are:
1:MUL need EAX:EDX, shift operation need ECX, so they aren't fit
for general eBPF 64bit register simulation.
2:We need at least 4 registers to simulate most eBPF ISA operations
on registers operands instead of on register&memory operands.
3:We need to put BPF_REG_AX on hardware registers, or constant blinding
will degrade jit performance heavily.
Tested on PC (Intel(R) Core(TM) i5-5200U CPU).
Testing results on i5-5200U:
1) test_bpf: Summary: 349 PASSED, 0 FAILED, [319/341 JIT'ed]
2) test_progs: Summary: 83 PASSED, 0 FAILED.
3) test_lpm: OK
4) test_lru_map: OK
5) test_verifier: Summary: 828 PASSED, 0 FAILED.
Above tests are all done in following two conditions separately:
1:bpf_jit_enable=1 and bpf_jit_harden=0
2:bpf_jit_enable=1 and bpf_jit_harden=2
Below are some numbers for this jit implementation:
Note:
I run test_progs in kselftest 100 times continuously for every condition,
the numbers are in format: total/times=avg.
The numbers that test_bpf reports show almost the same relation.
a:jit_enable=0 and jit_harden=0 b:jit_enable=1 and jit_harden=0
test_pkt_access:PASS:ipv4:15622/100=156 test_pkt_access:PASS:ipv4:10674/100=106
test_pkt_access:PASS:ipv6:9130/100=91 test_pkt_access:PASS:ipv6:4855/100=48
test_xdp:PASS:ipv4:240198/100=2401 test_xdp:PASS:ipv4:138912/100=1389
test_xdp:PASS:ipv6:137326/100=1373 test_xdp:PASS:ipv6:68542/100=685
test_l4lb:PASS:ipv4:61100/100=611 test_l4lb:PASS:ipv4:37302/100=373
test_l4lb:PASS:ipv6:101000/100=1010 test_l4lb:PASS:ipv6:55030/100=550
c:jit_enable=1 and jit_harden=2
test_pkt_access:PASS:ipv4:10558/100=105
test_pkt_access:PASS:ipv6:5092/100=50
test_xdp:PASS:ipv4:131902/100=1319
test_xdp:PASS:ipv6:77932/100=779
test_l4lb:PASS:ipv4:38924/100=389
test_l4lb:PASS:ipv6:57520/100=575
The numbers show we get 30%~50% improvement.
See Documentation/networking/filter.txt for more information.
Changelog:
Changes v5-v6:
1:Add do {} while (0) to RETPOLINE_RAX_BPF_JIT for
consistence reason.
2:Clean up non-standard comments, reported by Daniel Borkmann.
3:Fix a memory leak issue, repoted by Daniel Borkmann.
Changes v4-v5:
1:Delete is_on_stack, BPF_REG_AX is the only one
on real hardware registers, so just check with
it.
2:Apply commit 1612a981b7 ("bpf, x64: fix JIT emission
for dead code"), suggested by Daniel Borkmann.
Changes v3-v4:
1:Fix changelog in commit.
I install llvm-6.0, then test_progs willn't report errors.
I submit another patch:
"bpf: fix misaligned access for BPF_PROG_TYPE_PERF_EVENT program type on x86_32 platform"
to fix another problem, after that patch, test_verifier willn't report errors too.
2:Fix clear r0[1] twice unnecessarily in *BPF_IND|BPF_ABS* simulation.
Changes v2-v3:
1:Move BPF_REG_AX to real hardware registers for performance reason.
3:Using bpf_load_pointer instead of bpf_jit32.S, suggested by Daniel Borkmann.
4:Delete partial codes in 1c2a088a66, suggested by Daniel Borkmann.
5:Some bug fixes and comments improvement.
Changes v1-v2:
1:Fix bug in emit_ia32_neg64.
2:Fix bug in emit_ia32_arsh_r64.
3:Delete filename in top level comment, suggested by Thomas Gleixner.
4:Delete unnecessary boiler plate text, suggested by Thomas Gleixner.
5:Rewrite some words in changelog.
6:CodingSytle improvement and a little more comments.
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The JIT logic in jit_subprogs() is as follows: for all subprogs we
allocate a bpf_prog_alloc(), populate it (prog->is_func = 1 here),
and pass it to bpf_int_jit_compile(). If a failure occurred during
JIT and prog->jited is not set, then we bail out from attempting to
JIT the whole program, and punt to the interpreter instead. In case
JITing went successful, we fixup BPF call offsets and do another
pass to bpf_int_jit_compile() (extra_pass is true at that point) to
complete JITing calls. Given that requires to pass JIT context around
addrs and jit_data from x86 JIT are freed in the extra_pass in
bpf_int_jit_compile() when calls are involved (if not, they can
be freed immediately). However, if in the original pass, the JIT
image didn't converge then we leak addrs and jit_data since image
itself is NULL, the prog->is_func is set and extra_pass is false
in that case, meaning both will become unreachable and are never
cleaned up, therefore we need to free as well on !image. Only x64
JIT is affected.
Fixes: 1c2a088a66 ("bpf: x64: add JIT support for multi-function programs")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
While reviewing x64 JIT code, I noticed that we leak the prior allocated
JIT image in the case where proglen != oldproglen during the JIT passes.
Prior to the commit e0ee9c1215 ("x86: bpf_jit: fix two bugs in eBPF JIT
compiler") we would just break out of the loop, and using the image as the
JITed prog since it could only shrink in size anyway. After e0ee9c1215,
we would bail out to out_addrs label where we free addrs and jit_data but
not the image coming from bpf_jit_binary_alloc().
Fixes: e0ee9c1215 ("x86: bpf_jit: fix two bugs in eBPF JIT compiler")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
So by chance I looked into x86 assembly in arch/x86/net/bpf_jit_comp.c and
noticed the weird and inconsistent comment style it mistakenly learned from
the networking code:
/* Multi-line comment ...
* ... looks like this.
*/
Fix this to use the standard comment style specified in Documentation/CodingStyle
and used in arch/x86/ as well:
/*
* Multi-line comment ...
* ... looks like this.
*/
Also, to quote Linus's ... more explicit views about this:
http://article.gmane.org/gmane.linux.kernel.cryptoapi/21066
> But no, the networking code picked *none* of the above sane formats.
> Instead, it picked these two models that are just half-arsed
> shit-for-brains:
>
> (no)
> /* This is disgusting drug-induced
> * crap, and should die
> */
>
> (no-no-no)
> /* This is also very nasty
> * and visually unbalanced */
>
> Please. The networking code actually has the *worst* possible comment
> style. You can literally find that (no-no-no) style, which is just
> really horribly disgusting and worse than the otherwise fairly similar
> (d) in pretty much every way.
Also improve the comments and some other details while at it:
- Don't mix same-line and previous-line comment style on otherwise
identical code patterns within the same function,
- capitalize 'BPF' and x86 register names consistently,
- capitalize sentences consistently,
- instead of 'x64' use 'x86-64': x64 is a Microsoft specific term,
- use more consistent punctuation,
- use standard coding style in macros as well,
- fix typos and a few other minor details.
Consistent coding style is not optional, at least in arch/x86/.
No change in functionality.
( In case this commit causes conflicts with pending development code
I'll be glad to help resolve any conflicts! )
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Commit 2a5418a13f ("bpf: improve dead code sanitizing") replaced dead
code with a series of ja-1 instructions, for safety. That made JIT
compilation much more complex for some BPF programs. One instance of such
programs is, for example:
bool flag = false
...
/* A bunch of other code */
...
if (flag)
do_something()
In some cases llvm is not able to remove at compile time the code for
do_something(), so the generated BPF program ends up with a large amount
of dead instructions. In one specific real life example, there are two
series of ~500 and ~1000 dead instructions in the program. When the
verifier replaces them with a series of ja-1 instructions, it causes an
interesting behavior at JIT time.
During the first pass, since all the instructions are estimated at 64
bytes, the ja-1 instructions end up being translated as 5 bytes JMP
instructions (0xE9), since the jump offsets become increasingly large (>
127) as each instruction gets discovered to be 5 bytes instead of the
estimated 64.
Starting from the second pass, the first N instructions of the ja-1
sequence get translated into 2 bytes JMPs (0xEB) because the jump offsets
become <= 127 this time. In particular, N is defined as roughly 127 / (5
- 2) ~= 42. So, each further pass will make the subsequent N JMP
instructions shrink from 5 to 2 bytes, making the image shrink every time.
This means that in order to have the entire program converge, there need
to be, in the real example above, at least ~1000 / 42 ~= 24 passes just
for translating the dead code. If we add this number to the passes needed
to translate the other non dead code, it brings such program to 40+
passes, and JIT doesn't complete. Ultimately the userspace loader fails
because such BPF program was supposed to be part of a prog array owner
being JITed.
While it is certainly possible to try to refactor such programs to help
the compiler remove dead code, the behavior is not really intuitive and it
puts further burden on the BPF developer who is not expecting such
behavior. To make things worse, such programs are working just fine in all
the kernel releases prior to the ja-1 fix.
A possible approach to mitigate this behavior consists into noticing that
for ja-1 instructions we don't really need to rely on the estimated size
of the previous and current instructions, we know that a -1 BPF jump
offset can be safely translated into a 0xEB instruction with a jump offset
of -2.
Such fix brings the BPF program in the previous example to complete again
in ~9 passes.
Fixes: 2a5418a13f ("bpf: improve dead code sanitizing")
Signed-off-by: Gianluca Borello <g.borello@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In Cilium some of the main programs we run today are hitting 9 passes
on x64's JIT compiler, and we've had cases already where we surpassed
the limit where the JIT then punts the program to the interpreter
instead, leading to insertion failures due to CONFIG_BPF_JIT_ALWAYS_ON
or insertion failures due to the prog array owner being JITed but the
program to insert not (both must have the same JITed/non-JITed property).
One concrete case the program image shrunk from 12,767 bytes down to
10,288 bytes where the image converged after 16 steps. I've measured
that this took 340us in the JIT until it converges on my i7-6600U. Thus,
increase the original limit we had from day one where the JIT covered
cBPF only back then before we run into the case (as similar with the
complexity limit) where we trip over this and hit program rejections.
Also add a cond_resched() into the compilation loop, the JIT process
runs without any locks and may sleep anyway.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Unlike other archs flush_icache_range() is a noop on x64, therefore
remove the JIT's bpf_flush_icache() altogether since not needed.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Eric Dumazet <edumazet@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-02-26
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Various improvements for BPF kselftests: i) skip unprivileged tests
when kernel.unprivileged_bpf_disabled sysctl knob is set, ii) count
the number of skipped tests from unprivileged, iii) when a test case
had an unexpected error then print the actual but also the unexpected
one for better comparison, from Joe.
2) Add a sample program for collecting CPU state statistics with regards
to how long the CPU resides in cstate and pstate levels. Based on
cpu_idle and cpu_frequency trace points, from Leo.
3) Various x64 BPF JIT optimizations to further shrink the generated
image size in order to make it more icache friendly. When tested on
the Cilium generated programs, image size reduced by approx 4-5% in
best case mainly due to how LLVM emits unsigned 32 bit constants,
from Daniel.
4) Improvements and fixes on the BPF sockmap sample programs: i) fix
the sockmap's Makefile to include nlattr.o for libbpf, ii) detach
the sock ops programs from the cgroup before exit, from Prashant.
5) Avoid including xdp.h in filter.h by just forward declaring the
struct xdp_rxq_info in filter.h, from Jesper.
6) Fix the BPF kselftests Makefile for cgroup_helpers.c by only declaring
it a dependency for test_dev_cgroup.c but not every other test case
where it is not needed, from Jesper.
7) Adjust rlimit RLIMIT_MEMLOCK for test_tcpbpf_user selftest since the
default is insufficient for creating the 'global_map' used in the
corresponding BPF program, from Yonghong.
8) Likewise, for the xdp_redirect sample, Tushar ran into the same when
invoking xdp_redirect and xdp_monitor at the same time, therefore
in order to have the sample generically work bump the limit here,
too. Fix from Tushar.
9) Avoid an unnecessary NULL check in BPF_CGROUP_RUN_PROG_INET_SOCK()
since sk is always guaranteed to be non-NULL, from Yafang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
While it's rather cumbersome to reduce prologue for cBPF->eBPF
migrations wrt spill/fill for r15 which is callee saved register
due to bpf_error path in bpf_jit.S that is both used by migrations
as well as native eBPF, we can still trivially save 5 bytes in
prologue for the former since tail calls can never be used there.
cBPF->eBPF migrations also have their own custom prologue in BPF
asm that xors A and X reg anyway, so it's fine we skip this here.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add a generic emit_mov_reg() helper in order to reuse it in BPF
multiplication to load the src into rax, we can save a few bytes
in alu32 while doing so.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Instead of unconditionally performing push/pop on rax/rdx
in case of multiplication, we can save a few bytes in case
of dest register being either BPF r0 (rax) or r3 (rdx)
since the result is written in there anyway.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
While analyzing some of the more complex BPF programs from Cilium,
I found that LLVM generally prefers to emit LD_IMM64 instead of MOV32
BPF instructions for loading unsigned 32-bit immediates into a
register. Given we cannot change the current/stable LLVM versions
that are already out there, lets optimize this case such that the
JIT prefers to emit 'mov %eax, imm32' over 'movabsq %rax, imm64'
whenever suitable in order to reduce the image size by 4-5 bytes per
such load in the typical case, reducing image size on some of the
bigger programs by up to 4%. emit_mov_imm32() and emit_mov_imm64()
have been added as helpers.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
When we shift by one, we can use a different encoding where imm
is not explicitly needed, which saves 1 byte per such op.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Implement a retpoline [0] for the BPF tail call JIT'ing that converts
the indirect jump via jmp %rax that is used to make the long jump into
another JITed BPF image. Since this is subject to speculative execution,
we need to control the transient instruction sequence here as well
when CONFIG_RETPOLINE is set, and direct it into a pause + lfence loop.
The latter aligns also with what gcc / clang emits (e.g. [1]).
JIT dump after patch:
# bpftool p d x i 1
0: (18) r2 = map[id:1]
2: (b7) r3 = 0
3: (85) call bpf_tail_call#12
4: (b7) r0 = 2
5: (95) exit
With CONFIG_RETPOLINE:
# bpftool p d j i 1
[...]
33: cmp %edx,0x24(%rsi)
36: jbe 0x0000000000000072 |*
38: mov 0x24(%rbp),%eax
3e: cmp $0x20,%eax
41: ja 0x0000000000000072 |
43: add $0x1,%eax
46: mov %eax,0x24(%rbp)
4c: mov 0x90(%rsi,%rdx,8),%rax
54: test %rax,%rax
57: je 0x0000000000000072 |
59: mov 0x28(%rax),%rax
5d: add $0x25,%rax
61: callq 0x000000000000006d |+
66: pause |
68: lfence |
6b: jmp 0x0000000000000066 |
6d: mov %rax,(%rsp) |
71: retq |
72: mov $0x2,%eax
[...]
* relative fall-through jumps in error case
+ retpoline for indirect jump
Without CONFIG_RETPOLINE:
# bpftool p d j i 1
[...]
33: cmp %edx,0x24(%rsi)
36: jbe 0x0000000000000063 |*
38: mov 0x24(%rbp),%eax
3e: cmp $0x20,%eax
41: ja 0x0000000000000063 |
43: add $0x1,%eax
46: mov %eax,0x24(%rbp)
4c: mov 0x90(%rsi,%rdx,8),%rax
54: test %rax,%rax
57: je 0x0000000000000063 |
59: mov 0x28(%rax),%rax
5d: add $0x25,%rax
61: jmpq *%rax |-
63: mov $0x2,%eax
[...]
* relative fall-through jumps in error case
- plain indirect jump as before
[0] https://support.google.com/faqs/answer/7625886
[1] a31e654fa1
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Since we've changed div/mod exception handling for src_reg in
eBPF verifier itself, remove the leftovers from x86_64 JIT.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
For the BPF_REG_0 (BPF_REG_A in cBPF, respectively), we can use
the short form of the opcode as dst mapping is on eax/rax and
thus save a byte per such operation. Added to add/sub/and/or/xor
for 32/64 bit when K immediate is used. There may be more such
low-hanging fruit to add in future as well.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Having a pure_initcall() callback just to permanently enable BPF
JITs under CONFIG_BPF_JIT_ALWAYS_ON is unnecessary and could leave
a small race window in future where JIT is still disabled on boot.
Since we know about the setting at compilation time anyway, just
initialize it properly there. Also consolidate all the individual
bpf_jit_enable variables into a single one and move them under one
location. Moreover, don't allow for setting unspecified garbage
values on them.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Typical JIT does several passes over bpf instructions to
compute total size and relative offsets of jumps and calls.
With multitple bpf functions calling each other all relative calls
will have invalid offsets intially therefore we need to additional
last pass over the program to emit calls with correct offsets.
For example in case of three bpf functions:
main:
call foo
call bpf_map_lookup
exit
foo:
call bar
exit
bar:
exit
We will call bpf_int_jit_compile() indepedently for main(), foo() and bar()
x64 JIT typically does 4-5 passes to converge.
After these initial passes the image for these 3 functions
will be good except call targets, since start addresses of
foo() and bar() are unknown when we were JITing main()
(note that call bpf_map_lookup will be resolved properly
during initial passes).
Once start addresses of 3 functions are known we patch
call_insn->imm to point to right functions and call
bpf_int_jit_compile() again which needs only one pass.
Additional safety checks are done to make sure this
last pass doesn't produce image that is larger or smaller
than previous pass.
When constant blinding is on it's applied to all functions
at the first pass, since doing it once again at the last
pass can change size of the JITed code.
Tested on x64 and arm64 hw with JIT on/off, blinding on/off.
x64 jits bpf-to-bpf calls correctly while arm64 falls back to interpreter.
All other JITs that support normal BPF_CALL will behave the same way
since bpf-to-bpf call is equivalent to bpf-to-kernel call from
JITs point of view.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
global bpf_jit_enable variable is tested multiple times in JITs,
blinding and verifier core. The malicious root can try to toggle
it while loading the programs. This race condition was accounted
for and there should be no issues, but it's safer to avoid
this race condition.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
- bpf prog_array just like all other types of bpf array accepts 32-bit index.
Clarify that in the comment.
- fix x64 JIT of bpf_tail_call which was incorrectly loading 8 instead of 4 bytes
- tighten corresponding check in the interpreter to stay consistent
The JIT bug can be triggered after introduction of BPF_F_NUMA_NODE flag
in commit 96eabe7a40 in 4.14. Before that the map_flags would stay zero and
though JIT code is wrong it will check bounds correctly.
Hence two fixes tags. All other JITs don't have this problem.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Fixes: 96eabe7a40 ("bpf: Allow selecting numa node during map creation")
Fixes: b52f00e6a7 ("x86: bpf_jit: implement bpf_tail_call() helper")
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work implements jiting of BPF_J{LT,LE,SLT,SLE} instructions
with BPF_X/BPF_K variants for the x86_64 eBPF JIT.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Reasonably busy this cycle, but perhaps not as busy as in the 4.12
merge window:
1) Several optimizations for UDP processing under high load from
Paolo Abeni.
2) Support pacing internally in TCP when using the sch_fq packet
scheduler for this is not practical. From Eric Dumazet.
3) Support mutliple filter chains per qdisc, from Jiri Pirko.
4) Move to 1ms TCP timestamp clock, from Eric Dumazet.
5) Add batch dequeueing to vhost_net, from Jason Wang.
6) Flesh out more completely SCTP checksum offload support, from
Davide Caratti.
7) More plumbing of extended netlink ACKs, from David Ahern, Pablo
Neira Ayuso, and Matthias Schiffer.
8) Add devlink support to nfp driver, from Simon Horman.
9) Add RTM_F_FIB_MATCH flag to RTM_GETROUTE queries, from Roopa
Prabhu.
10) Add stack depth tracking to BPF verifier and use this information
in the various eBPF JITs. From Alexei Starovoitov.
11) Support XDP on qed device VFs, from Yuval Mintz.
12) Introduce BPF PROG ID for better introspection of installed BPF
programs. From Martin KaFai Lau.
13) Add bpf_set_hash helper for TC bpf programs, from Daniel Borkmann.
14) For loads, allow narrower accesses in bpf verifier checking, from
Yonghong Song.
15) Support MIPS in the BPF selftests and samples infrastructure, the
MIPS eBPF JIT will be merged in via the MIPS GIT tree. From David
Daney.
16) Support kernel based TLS, from Dave Watson and others.
17) Remove completely DST garbage collection, from Wei Wang.
18) Allow installing TCP MD5 rules using prefixes, from Ivan
Delalande.
19) Add XDP support to Intel i40e driver, from Björn Töpel
20) Add support for TC flower offload in nfp driver, from Simon
Horman, Pieter Jansen van Vuuren, Benjamin LaHaise, Jakub
Kicinski, and Bert van Leeuwen.
21) IPSEC offloading support in mlx5, from Ilan Tayari.
22) Add HW PTP support to macb driver, from Rafal Ozieblo.
23) Networking refcount_t conversions, From Elena Reshetova.
24) Add sock_ops support to BPF, from Lawrence Brako. This is useful
for tuning the TCP sockopt settings of a group of applications,
currently via CGROUPs"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1899 commits)
net: phy: dp83867: add workaround for incorrect RX_CTRL pin strap
dt-bindings: phy: dp83867: provide a workaround for incorrect RX_CTRL pin strap
cxgb4: Support for get_ts_info ethtool method
cxgb4: Add PTP Hardware Clock (PHC) support
cxgb4: time stamping interface for PTP
nfp: default to chained metadata prepend format
nfp: remove legacy MAC address lookup
nfp: improve order of interfaces in breakout mode
net: macb: remove extraneous return when MACB_EXT_DESC is defined
bpf: add missing break in for the TCP_BPF_SNDCWND_CLAMP case
bpf: fix return in load_bpf_file
mpls: fix rtm policy in mpls_getroute
net, ax25: convert ax25_cb.refcount from atomic_t to refcount_t
net, ax25: convert ax25_route.refcount from atomic_t to refcount_t
net, ax25: convert ax25_uid_assoc.refcount from atomic_t to refcount_t
net, sctp: convert sctp_ep_common.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_transport.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_chunk.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_datamsg.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_auth_bytes.refcnt from atomic_t to refcount_t
...
In preparation for an objtool rewrite which will have broader checks,
whitelist functions and files which cause problems because they do
unusual things with the stack.
These whitelists serve as a TODO list for which functions and files
don't yet have undwarf unwinder coverage. Eventually most of the
whitelists can be removed in favor of manual CFI hint annotations or
objtool improvements.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: live-patching@vger.kernel.org
Link: http://lkml.kernel.org/r/7f934a5d707a574bda33ea282e9478e627fb1829.1498659915.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add jited_len to struct bpf_prog. It will be
useful for the struct bpf_prog_info which will
be added in the later patch.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take advantage of stack_depth tracking in x64 JIT.
Round up allocated stack by 8 bytes to make sure it stays aligned
for functions called from JITed bpf program.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
in order to JIT programs with different stack sizes we need to
make epilogue and exception path to be stack size independent,
hence move auxiliary stack space from the bottom of the stack
to the top of the stack.
Nice side effect is that JITed function prologue becomes shorter
due to imm8 offset encoding vs imm32.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
free up BPF_JMP | BPF_CALL | BPF_X opcode to be used by actual
indirect call by register and use kernel internal opcode to
mark call instruction into bpf_tail_call() helper.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
set_memory_* functions have moved to set_memory.h. Switch to this
explicitly.
Link: http://lkml.kernel.org/r/1488920133-27229-6-git-send-email-labbott@redhat.com
Signed-off-by: Laura Abbott <labbott@redhat.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For both cases, the verifier is already rejecting such invalid
formed instructions. Thus, remove these artifacts from old times
and align it with ppc64, sparc64 and s390x JITs that don't have
them in the first place.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric and Willem reported that they recently saw random crashes when
JIT was in use and bisected this to 74451e66d5 ("bpf: make jited
programs visible in traces"). Issue was that the consolidation part
added bpf_jit_binary_unlock_ro() that would unlock previously made
read-only memory back to read-write. However, DEBUG_SET_MODULE_RONX
cannot be used for this to test for presence of set_memory_*()
functions. We need to use ARCH_HAS_SET_MEMORY instead to fix this;
also add the corresponding bpf_jit_binary_lock_ro() to filter.h.
Fixes: 74451e66d5 ("bpf: make jited programs visible in traces")
Reported-by: Eric Dumazet <edumazet@google.com>
Reported-by: Willem de Bruijn <willemb@google.com>
Bisected-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Long standing issue with JITed programs is that stack traces from
function tracing check whether a given address is kernel code
through {__,}kernel_text_address(), which checks for code in core
kernel, modules and dynamically allocated ftrace trampolines. But
what is still missing is BPF JITed programs (interpreted programs
are not an issue as __bpf_prog_run() will be attributed to them),
thus when a stack trace is triggered, the code walking the stack
won't see any of the JITed ones. The same for address correlation
done from user space via reading /proc/kallsyms. This is read by
tools like perf, but the latter is also useful for permanent live
tracing with eBPF itself in combination with stack maps when other
eBPF types are part of the callchain. See offwaketime example on
dumping stack from a map.
This work tries to tackle that issue by making the addresses and
symbols known to the kernel. The lookup from *kernel_text_address()
is implemented through a latched RB tree that can be read under
RCU in fast-path that is also shared for symbol/size/offset lookup
for a specific given address in kallsyms. The slow-path iteration
through all symbols in the seq file done via RCU list, which holds
a tiny fraction of all exported ksyms, usually below 0.1 percent.
Function symbols are exported as bpf_prog_<tag>, in order to aide
debugging and attribution. This facility is currently enabled for
root-only when bpf_jit_kallsyms is set to 1, and disabled if hardening
is active in any mode. The rationale behind this is that still a lot
of systems ship with world read permissions on kallsyms thus addresses
should not get suddenly exposed for them. If that situation gets
much better in future, we always have the option to change the
default on this. Likewise, unprivileged programs are not allowed
to add entries there either, but that is less of a concern as most
such programs types relevant in this context are for root-only anyway.
If enabled, call graphs and stack traces will then show a correct
attribution; one example is illustrated below, where the trace is
now visible in tooling such as perf script --kallsyms=/proc/kallsyms
and friends.
Before:
7fff8166889d bpf_clone_redirect+0x80007f0020ed (/lib/modules/4.9.0-rc8+/build/vmlinux)
f5d80 __sendmsg_nocancel+0xffff006451f1a007 (/usr/lib64/libc-2.18.so)
After:
7fff816688b7 bpf_clone_redirect+0x80007f002107 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fffa0575728 bpf_prog_33c45a467c9e061a+0x8000600020fb (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fffa07ef1fc cls_bpf_classify+0x8000600020dc (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff81678b68 tc_classify+0x80007f002078 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff8164d40b __netif_receive_skb_core+0x80007f0025fb (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff8164d718 __netif_receive_skb+0x80007f002018 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff8164e565 process_backlog+0x80007f002095 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff8164dc71 net_rx_action+0x80007f002231 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff81767461 __softirqentry_text_start+0x80007f0020d1 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff817658ac do_softirq_own_stack+0x80007f00201c (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff810a2c20 do_softirq+0x80007f002050 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff810a2cb5 __local_bh_enable_ip+0x80007f002085 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff8168d452 ip_finish_output2+0x80007f002152 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff8168ea3d ip_finish_output+0x80007f00217d (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff8168f2af ip_output+0x80007f00203f (/lib/modules/4.9.0-rc8+/build/vmlinux)
[...]
7fff81005854 do_syscall_64+0x80007f002054 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff817649eb return_from_SYSCALL_64+0x80007f002000 (/lib/modules/4.9.0-rc8+/build/vmlinux)
f5d80 __sendmsg_nocancel+0xffff01c484812007 (/usr/lib64/libc-2.18.so)
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the dummy bpf_jit_compile() stubs for eBPF JITs and make
that a single __weak function in the core that can be overridden
similarly to the eBPF one. Also remove stale pr_err() mentions
of bpf_jit_compile.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If after too many passes still no image could be emitted, then
swap back to the original program as we do in all other cases
and don't use the one with blinding.
Fixes: 959a757916 ("bpf, x86: add support for constant blinding")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows XDP prog to extend/remove the packet
data at the head (like adding or removing header). It is
done by adding a new XDP helper bpf_xdp_adjust_head().
It also renames bpf_helper_changes_skb_data() to
bpf_helper_changes_pkt_data() to better reflect
that XDP prog does not work on skb.
This patch adds one "xdp_adjust_head" bit to bpf_prog for the
XDP-capable driver to check if the XDP prog requires
bpf_xdp_adjust_head() support. The driver can then decide
to error out during XDP_SETUP_PROG.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds recently added constant blinding helpers into the
x86 eBPF JIT. In the bpf_int_jit_compile() path, requirements are
to utilize bpf_jit_blind_constants()/bpf_jit_prog_release_other()
pair for rewriting the program into a blinded one, and to map the
BPF_REG_AX register to a CPU register. The mapping of BPF_REG_AX
is at non-callee saved register r10, and thus shared with cached
skb->data used for ld_abs/ind and not in every program type needed.
When blinding is not used, there's zero additional overhead in the
generated image.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the blinding is strictly only called from inside eBPF JITs,
we need to change signatures for bpf_int_jit_compile() and
bpf_prog_select_runtime() first in order to prepare that the
eBPF program we're dealing with can change underneath. Hence,
for call sites, we need to return the latest prog. No functional
change in this patch.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is never such a situation, where bpf_int_jit_compile() is
called with either prog as NULL or len as 0, so the tests are
unnecessary and confusing as people would just copy them. s390
doesn't have them, so no change is needed there.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
bpf_jit.S has several callable non-leaf functions which don't honor
CONFIG_FRAME_POINTER, which can result in bad stack traces.
Create a stack frame before the call instructions when
CONFIG_FRAME_POINTER is enabled.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Bernd Petrovitsch <bernd@petrovitsch.priv.at>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Chris J Arges <chris.j.arges@canonical.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: live-patching@vger.kernel.org
Cc: netdev@vger.kernel.org
Link: http://lkml.kernel.org/r/fa4c41976b438b51954cb8021f06bceb1d1d66cc.1453405861.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
bpf_jit.S has several functions which can be called from C code. Give
them proper ELF annotations.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Bernd Petrovitsch <bernd@petrovitsch.priv.at>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Chris J Arges <chris.j.arges@canonical.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: live-patching@vger.kernel.org
Cc: netdev@vger.kernel.org
Link: http://lkml.kernel.org/r/bbe1de0c299fecd4fc9a1766bae8be2647bedb01.1453405861.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When sometimes structs or variables need to be initialized/'memset' to 0 in
an eBPF C program, the x86 BPF JIT converts this to use immediates. We can
however save a couple of bytes (f.e. even up to 7 bytes on a single emmission
of BPF_LD | BPF_IMM | BPF_DW) in the image by detecting such case and use xor
on the dst register instead.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Back in the days where eBPF (or back then "internal BPF" ;->) was not
exposed to user space, and only the classic BPF programs internally
translated into eBPF programs, we missed the fact that for classic BPF
A and X needed to be cleared. It was fixed back then via 83d5b7ef99
("net: filter: initialize A and X registers"), and thus classic BPF
specifics were added to the eBPF interpreter core to work around it.
This added some confusion for JIT developers later on that take the
eBPF interpreter code as an example for deriving their JIT. F.e. in
f75298f5c3 ("s390/bpf: clear correct BPF accumulator register"), at
least X could leak stack memory. Furthermore, since this is only needed
for classic BPF translations and not for eBPF (verifier takes care
that read access to regs cannot be done uninitialized), more complexity
is added to JITs as they need to determine whether they deal with
migrations or native eBPF where they can just omit clearing A/X in
their prologue and thus reduce image size a bit, see f.e. cde66c2d88
("s390/bpf: Only clear A and X for converted BPF programs"). In other
cases (x86, arm64), A and X is being cleared in the prologue also for
eBPF case, which is unnecessary.
Lets move this into the BPF migration in bpf_convert_filter() where it
actually belongs as long as the number of eBPF JITs are still few. It
can thus be done generically; allowing us to remove the quirk from
__bpf_prog_run() and to slightly reduce JIT image size in case of eBPF,
while reducing code duplication on this matter in current(/future) eBPF
JITs.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Tested-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Zi Shen Lim <zlim.lnx@gmail.com>
Cc: Yang Shi <yang.shi@linaro.org>
Acked-by: Yang Shi <yang.shi@linaro.org>
Acked-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we need to add further flags to the bpf_prog structure, lets migrate
both bools to a bitfield representation. The size of the base structure
(excluding insns) remains unchanged at 40 bytes.
Add also tags for the kmemchecker, so that it doesn't throw false
positives. Even in case gcc would generate suboptimal code, it's not
being accessed in performance critical paths.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the map backends are of generic nature. In order to avoid
adding much special code into the eBPF core, rewrite part of
the bpf_prog_array map code and make it more generic. So the
new perf_event_array map type can reuse most of code with
bpf_prog_array map and add fewer lines of special code.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Signed-off-by: Kaixu Xia <xiakaixu@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/s390/net/bpf_jit_comp.c
drivers/net/ethernet/ti/netcp_ethss.c
net/bridge/br_multicast.c
net/ipv4/ip_fragment.c
All four conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
