Reverts commit 3ab2512337
[media] af9035: override tuner for AVerMedia A835B devices
Original commit itself is correct, but it was replaced by more
general solution (commit 1cbbf90d04).
This old solution was committed by a accident and is not needed
anymore.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Old IT9135 AX needs a little bit different register settings for
sleep than newer IT9135 BX. This has been broken always, as power
management of the whole driver, but it started to be problem as I
fixed clock. Earlier clock was disabled very first on sleep and
rest of the commands were skipped by the chip as no clock, leaving
tuner full power state. When I fixed clocks these PM bugs started
raising out as I/O errors.
Cc: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Error on init leaves some internal divisor zero, which causes oops
later. Fix it by populating divisors even it fails.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
IT913x tuner driver disables own clock, provided by demod core, as
very a first operation when tuner is put on *sleep*. That likely
causes failure of all the rest commands on sleep sequence, which
leads situation where tuner is not actually on sleep, but consuming
a lot of power.
I measured 102mA current consumption from the USB before change
and after change it was only 32mA. Used device was single tuner
IT9135 BX.
Second reason to remove that register from tuner driver is reason
it is simply on wrong driver (demod vs. tuner), breaking the
principle of correct driver.
Clock is now provided more correctly af9033 demod driver as a
config option.
Cc: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Integrated RF tuner of IT9135 is connected to demod clock source
named dyn0_clk. Enable that clock source in order to provide stable
clock early enough.
Cc: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
AF903x/IT913x demod provides clock source(s). It seems that this
clock source is used for integrated RF tuner of IT913x. It is
enabled by default, but firmware disables it automatically when
suspend is requested (suspend_flag (0x004c) + trigger_ofsm
(0x0000)). Automatic disable behavior seems to be similar for both
AF903x and IT913x I tested, though there is no likely any real
clock user in a case of AF903x.
Cc: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
coda-bit uses kmalloc/kfree functions, so the slab header needs to be included
in order to fix the following build errors:
drivers/media/platform/coda/coda-bit.c: In function 'coda_fill_bitstream':
drivers/media/platform/coda/coda-bit.c:231:4: error: implicit declaration of function 'kmalloc' [-Werror=implicit-function-declaration]
drivers/media/platform/coda/coda-bit.c: In function 'coda_alloc_framebuffers':
drivers/media/platform/coda/coda-bit.c:312:3: error: implicit declaration of function 'kfree' [-Werror=implicit-function-declaration]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is 2 different versions of that chip available, master and
slave. Slave is used only on dual tuner devices with master tuner.
Laser printing top of chip is 18212/M or 18212/S according to chip
version.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a variable to keep track if firmware is loaded or not and skip parts of the
initialization if fw is already loaded. Resume from sleep with a different
command compared to initial power up and run command 85 after resume command.
This behaviour is observed when using manufacturer provided binary-only si2168
driver for TechnoTrend CT2-4400.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a variable into state to keep track if firmware has been loaded or not.
Skip firmware loading in case it is already loaded (resume from sleep).
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of sending command 13 to the tuner, send command 16 when sleeping. This
behaviour is observed when using manufacturer provided binary-only Linux driver
for TechnoTrend CT2-4400 (Windows driver does not do power management).
The issue with command 13 is that firmware loading is necessary after that.
This is not an issue with tuners that do not require firmware, but starting
streaming after sleep on an Si2158 takes noticeable time as firmware is
loaded on resume.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove function name from debug logs. Logging system could add it
automatically.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sample rate calculation gives a little bit too large results because
in real life there was around one milliseconds (~one usb packet) too
much data for given time. Calculate time more accurate in order to
provide better results.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is no need to init flags before calling spin_lock_irqsave().
spin_lock_irqsave is macro which stores value to 'flags'
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove function name from debug logs. Logging system could add it
automatically.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is no need to init flags before calling spin_lock_irqsave().
spin_lock_irqsave is macro which stores value to 'flags'.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove function name from debug logs. Logging system could add it
automatically.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Kernel logging system needs pointer to usb interface device in
order to print names and bus numbers properly. There was wrong
device pointer given and log printings wasn't correct.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sample rate calculation gives a little bit too large results because
in real life there was around one milliseconds (~one usb packet) too
much data for given time. Calculate time more accurate in order to
provide better results.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is no need to init flags before calling spin_lock_irqsave().
spin_lock_irqsave is a macro which stores value to 'flags'.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Kernel logging system needs pointer to usb interface device in
order to print names and bus numbers properly. There was wrong
device pointer given and log printings wasn't correct.
Remove some debug logging from v4l2 ioctl functions. v4l2 core debug
prints almost same information when enabled.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Free all reserved USB buffers and URBs on failure. Return all queued
buffers to vb2 with state queued on error case.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are some patches that depends on media-v3.16-rc6.
So, merge back from upstream before applying them.
* linus/master: (1123 commits)
drm/nouveau: ltc/gf100-: fix cbc issues on certain boards
drm/bochs: add missing drm_connector_register call
drm/cirrus: add missing drm_connector_register call
staging: vt6655: buffer overflow in ioctl
USB: storage: Add quirks for Entrega/Xircom USB to SCSI converters
USB: storage: Add quirk for Ariston Technologies iConnect USB to SCSI adapter
USB: storage: Add quirk for Adaptec USBConnect 2000 USB-to-SCSI Adapter
USB: EHCI: unlink QHs even after the controller has stopped
[SCSI] fix for bidi use after free
[SCSI] fix regression that accidentally disabled block-based tcq
[SCSI] libiscsi: fix potential buffer overrun in __iscsi_conn_send_pdu
drm/radeon: Fix typo 'addr' -> 'entry' in rs400_gart_set_page
drm/nouveau/runpm: fix module unload
drm/radeon/px: fix module unload
vgaswitcheroo: add vga_switcheroo_fini_domain_pm_ops
drm/radeon: don't reset dma on r6xx-evergreen init
drm/radeon: don't reset sdma on CIK init
drm/radeon: don't reset dma on NI/SI init
drm/radeon/dpm: fix resume on mullins
drm/radeon: Disable HDP flush before every CS again for < r600
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tsEN
-----END PGP SIGNATURE-----
Merge tag 'media-v3.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"some media bug fixes:
- a Kconfig dependency issue
- some fixes for af9033/it913x demod to be more reliable and address
a performance regression
- cx18: fix an oops on devices with tda8290 tuner
- two new USB IDs for af9035
- a couple fixes on smapp driver"
* tag 'media-v3.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] af9035: new IDs: add support for PCTV 78e and PCTV 79e
[media] af9033: feed clock to RF tuner
[media] it913x: init tuner on attach
[media] af9033: update IT9135 tuner inittabs
[media] Kconfig: do not select SPI bus on sub-driver auto-select
[media] cx18: fix kernel oops with tda8290 tuner
[media] smiapp: Set sub-device owner
[media] smiapp: Fix power count handling
Here are some IIO and Staging driver fixes for 3.17-rc6. They are all
pretty simple, and resolve reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlQdukgACgkQMUfUDdst+ymENwCfTYAbHywZxtdQRMQ+ByfAeQY4
5kIAnjb6xVPATRL9DMt/cUfyE550SiEz
=UW80
-----END PGP SIGNATURE-----
Merge tag 'staging-3.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging / IIO fixes from Greg KH:
"Here are some IIO and Staging driver fixes for 3.17-rc6. They are all
pretty simple, and resolve reported issues"
* tag 'staging-3.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: vt6655: buffer overflow in ioctl
iio:magnetometer: bugfix magnetometers gain values
iio: adc: at91: don't use the last converted data register
iio: adc: xilinx-xadc: assign auxiliary channels address correctly
iio: meter: ade7758: Fix indio_dev->trig assignment
iio: inv_mpu6050: Fix indio_dev->trig assignment
iio: gyro: itg3200: Fix indio_dev->trig assignment
iio: st_sensors: Fix indio_dev->trig assignment
iio: hid_sensor_hub: Fix indio_dev->trig assignment
iio: adc: ad_sigma_delta: Fix indio_dev->trig assignment
iio: accel: bma180: Fix indio_dev->trig assignment
iio:trigger: modify return value for iio_trigger_get
iio:inkern: fix overwritten -EPROBE_DEFER in of_iio_channel_get_by_name
Here are some USB and PHY fixes and quirks for 3.17-rc6. Nothing major,
just a few things that have been reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlQduf0ACgkQMUfUDdst+ylJdwCaAnzHvU6geu1tINSYpk0/XNKE
SgEAoJcaG0Nswpm5gKrJZbX0JstagIgn
=JOUD
-----END PGP SIGNATURE-----
Merge tag 'usb-3.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes / quirks from Greg KH:
"Here are some USB and PHY fixes and quirks for 3.17-rc6. Nothing
major, just a few things that have been reported"
* tag 'usb-3.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: storage: Add quirks for Entrega/Xircom USB to SCSI converters
USB: storage: Add quirk for Ariston Technologies iConnect USB to SCSI adapter
USB: storage: Add quirk for Adaptec USBConnect 2000 USB-to-SCSI Adapter
USB: EHCI: unlink QHs even after the controller has stopped
phy: spear1340-miphy: fix driver dependencies
phy: spear1310-miphy: fix driver dependencies
phy: miphy365x: Fix off-by-one error
Pull SCSI target fixes from Nicholas Bellinger:
"Here are the target pending fixes for v3.17-rc6.
Included are Sagi's long overdue fixes related to iser-target
shutdown, along with a couple of fixes from Sebastian related to ALUA
Referrals changes that when in during the v3.14 time-frame.
Also included are a few iscsi-target fixes, most recently of which
where found during Joern's Coverity scanning of target code"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: avoid NULL pointer in iscsi_copy_param_list failure
iscsi-target: Fix memory corruption in iscsit_logout_post_handler_diffcid
target: Fix inverted logic in SE_DEV_ALUA_SUPPORT_STATE_STORE
target: Fix user data segment multiplier in spc_emulate_evpd_b3()
iscsi-target: Ignore ICF_GOT_LAST_DATAOUT during Data-Out ITT lookup
Target/iser: Fix initiator_depth and responder_resources
Target/iser: Avoid calling rdma_disconnect twice
Target/iser: Don't put isert_conn inside disconnected handler
Target/iser: Get isert_conn reference once got to connected_handler
Pull drm fixes from Dave Airlie:
"A bunch of radeon fixes for oops on module unload, and problems with
resetting the dma engine, one nouveau fix for black boxes in rendering
on my mbp retina, one sti fix, and a couple of intel fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau: ltc/gf100-: fix cbc issues on certain boards
drm/bochs: add missing drm_connector_register call
drm/cirrus: add missing drm_connector_register call
drm/radeon: Fix typo 'addr' -> 'entry' in rs400_gart_set_page
drm/nouveau/runpm: fix module unload
drm/radeon/px: fix module unload
vgaswitcheroo: add vga_switcheroo_fini_domain_pm_ops
drm/radeon: don't reset dma on r6xx-evergreen init
drm/radeon: don't reset sdma on CIK init
drm/radeon: don't reset dma on NI/SI init
drm/radeon/dpm: fix resume on mullins
drm/radeon: Disable HDP flush before every CS again for < r600
drm/radeon: delete unused PTE_* defines
drm/i915: Add limited color range readout for HDMI/DP ports on g4x/vlv/chv
drm: sti: do not iterate over the info frame array
drm/i915: Fix SRC_COPY width on 830/845g
A mismatch between FB and LTC's idea of how big a large page is causes
issues such as black "holes" in rendering to occur on some boards
(those where LTC is configured for 64KiB large pages) when compression
is used.
Confirmed to fix at least the GK107 MBP.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
single fix for regression on rs4xx/rs690/rs740
* 'drm-fixes-3.17' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: Fix typo 'addr' -> 'entry' in rs400_gart_set_page
->u.generic_elem.len is a user controlled number between 0-255. We
should limit it to avoid memory corruption.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Fix an overwritten error return that can prevent deferred probing when
using of_iio_channel_get_by_name
* A series that deals with an incorrect reference count when the default
trigger is set within the main probe routine for a driver. Can result
in a double free if the trigger is changed.
* Fix a buglet with xilinx-xadc concerning setup of the address for an
aux channel.
* At91 adc driver could sometimes get a touchscreen reading rather than
the intended adc channel. This is fixed by using the channel data register
instead.
* Fix some ST magnetometer gain values that differ in production parts from
the prerelease ones used for driver development.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=MS7C
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-3.17a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First round of IIO fixes for the 3.17 cycle.
* Fix an overwritten error return that can prevent deferred probing when
using of_iio_channel_get_by_name
* A series that deals with an incorrect reference count when the default
trigger is set within the main probe routine for a driver. Can result
in a double free if the trigger is changed.
* Fix a buglet with xilinx-xadc concerning setup of the address for an
aux channel.
* At91 adc driver could sometimes get a touchscreen reading rather than
the intended adc channel. This is fixed by using the channel data register
instead.
* Fix some ST magnetometer gain values that differ in production parts from
the prerelease ones used for driver development.
This patch adds quirks for Entrega Technologies (later Xircom PortGear) USB-
SCSI converters. They use Shuttle Technology EUSB-01/EUSB-S1 chips. The
US_FL_SCM_MULT_TARG quirk is needed to allow multiple devices on the SCSI
chain to be accessed. Without it only the (single) device with SCSI ID 0
can be used.
The standalone converter sold by Entrega had model number U1-SC25. Xircom
acquired Entrega and re-branded the product line PortGear. The PortGear USB
to SCSI Converter (model PGSCSI) is internally identical to the Entrega
product, but later models may use a different USB ID. The Entrega-branded
units have USB ID 1645:0007, as does my Xircom PGSCSI, but the Windows and
Macintosh drivers also support 085A:0028.
Entrega also sold the "Mac USB Dock", which provides two USB ports, a Mac
(8-pin mini-DIN) serial port and a SCSI port. It appears to the computer as
a four-port hub, USB-serial, and USB-SCSI converters. The USB-SCSI part may
have initially used the same ID as the standalone U1-SC25 (1645:0007), but
later production used 085A:0026.
My Xircom PortGear PGSCSI has bcdDevice=0x0100. Units with bcdDevice=0x0133
probably also exist.
This patch adds quirks for 1645:0007, 085A:0026 and 085A:0028. The Windows
driver INF file also mentions 085A:0032 "PortStation SCSI Module", but I
couldn't find any mention of that actually existing in the wild; perhaps it
was cancelled before release?
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi,
The Ariston Technologies iConnect 025 and iConnect 050 (also known as e.g.
iSCSI-50) are SCSI-USB converters which use Shuttle Technology/SCM
Microsystems chips. Only the connectors differ; both have the same USB ID.
The US_FL_SCM_MULT_TARG quirk is required to use SCSI devices with ID other
than 0.
I don't have one of these, but based on the other entries for Shuttle/
SCM-based converters this patch is very likely correct. I used 0x0000 and
0x9999 for bcdDeviceMin and bcdDeviceMax because I'm not sure which
bcdDevice value the products use.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Adaptec USBConnect 2000 is another SCSI-USB converter which uses
Shuttle Technology/SCM Microsystems chips. The US_FL_SCM_MULT_TARG quirk is
required to use SCSI devices with ID other than 0.
I don't have a USBConnect 2000, but based on the other entries for Shuttle/
SCM-based converters this patch is very likely correct. I used 0x0000 and
0x9999 for bcdDeviceMin and bcdDeviceMax because I'm not sure which
bcdDevice value the product uses.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Old code in ehci-hcd tries to expedite disabling endpoints after the
controller has stopped, by destroying the endpoint's associated QH
without first unlinking the QH. This was necessary back when the
driver wasn't so careful about keeping track of the controller's
state.
But now we are careful about it, and the driver knows that when the
controller isn't running, no unlinking delay is needed. Furthermore,
skipping the unlink step will trigger a BUG() in qh_destroy() when the
preceding QH is released, because the link pointer will be non-NULL.
Removing the lines that skip the unlinking step and go directly to
QH_STATE_IDLE fixes the problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull btrfs fixes from Chris Mason:
"I've got a revert to fix a regression with btrfs device registration,
and Filipe has part two of his fsync fix from last week"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Revert "Btrfs: device_list_add() should not update list when mounted"
Btrfs: set inode's logged_trans/last_log_commit after ranged fsync
Highligts:
- Fix an Oops in nfs4_open_and_get_state
- Fix an Oops in the nfs4_state_manager
- Fix another bug in the close/open_downgrade code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=EOW6
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.17-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client fixes from Trond Myklebust:
"Highligts:
- fix an Oops in nfs4_open_and_get_state
- fix an Oops in the nfs4_state_manager
- fix another bug in the close/open_downgrade code"
* tag 'nfs-for-3.17-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4: Fix another bug in the close/open_downgrade code
NFSv4: nfs4_state_manager() vs. nfs_server_remove_lists()
NFS: remove BUG possibility in nfs4_open_and_get_state
Enumeration
- Don't default exclusively to first video device (Bruno Prémont)
PCI device hotplug
- Remove "no hotplug settings from platform" warning (Bjorn Helgaas)
- Add pci_ignore_hotplug() for VGA switcheroo (Bjorn Helgaas)
Freescale i.MX6
- Put LTSSM in "Detect" state before disabling (Lucas Stach)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xIYe
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.17-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These fix:
- Boot video device detection on dual-GPU Apple systems
- Hotplug fiascos on VGA switcheroo with radeon & nouveau drivers
- Boot hang on Freescale i.MX6 systems
- Excessive "no hotplug settings from platform" warnings
In particular:
Enumeration
- Don't default exclusively to first video device (Bruno Prémont)
PCI device hotplug
- Remove "no hotplug settings from platform" warning (Bjorn Helgaas)
- Add pci_ignore_hotplug() for VGA switcheroo (Bjorn Helgaas)
Freescale i.MX6
- Put LTSSM in "Detect" state before disabling (Lucas Stach)"
* tag 'pci-v3.17-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
vgaarb: Drop obsolete #ifndef
vgaarb: Don't default exclusively to first video device with mem+io
ACPIPHP / radeon / nouveau: Remove acpi_bus_no_hotplug()
PCI: Remove "no hotplug settings from platform" warning
PCI: Add pci_ignore_hotplug() to ignore hotplug events for a device
PCI: imx6: Put LTSSM in "Detect" state before disabling it
MAINTAINERS: Add Lucas Stach as co-maintainer for i.MX6 PCI driver
This is a set of three fixes. One represents a nasty shared tag map
regression (another inverted condition) caused by recent SCSI MQ patches, one
is a longstanding potential buffer overrun in the iscsi data buffer and the
final one is a use after free for the rare bidirectional commands.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJUHDQjAAoJEDeqqVYsXL0MAksIAMW7JMBW2BRSixKhqtZOsItd
DrYN1wfvOuoKgyKnXBfhLbgKih9UgMEnc4zWnB96gBnNJCwFpW9vIICdf6kCWwXh
c7Bh24SjcHMvYU9Of08TcAdUxyql6md/d28jzjoIi9zFj4C3XvLgevR8n4x2Lk2b
3SQnX/PYUVMd4sKZaTQDLLAy5+CYGf2tbLPHlMZQHlIN+Cgjorm8zW7tIWJ+rhrv
Sc3f9O9LxROsJ5wJNJpD0/9adlpsFxSD6cJWELaXBFsgw7jh0ZUjAXSYpyHASZqF
Mln4kNCEcoa3IIiLVxBbBoQCVF01+kYpGuZM4o4nU6b+wluXupcuhTh5o37G7Q8=
=FPm9
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of three fixes.
One represents a nasty shared tag map regression (another inverted
condition) caused by recent SCSI MQ patches, one is a longstanding
potential buffer overrun in the iscsi data buffer and the final one is
a use after free for the rare bidirectional commands"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] fix for bidi use after free
[SCSI] fix regression that accidentally disabled block-based tcq
[SCSI] libiscsi: fix potential buffer overrun in __iscsi_conn_send_pdu
Pull perf fixes from Ingo Molnar:
"Two kernel side fixes: a kprobes fix and a perf_remove_from_context()
fix (which does not yet fix the migration bug which is WIP)"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix a race condition in perf_remove_from_context()
kprobes/x86: Free 'optinsn' cache when range check fails
Pull x86 fixes from Ingo Molnar:
"Misc fixes:
EFI fixes, a build fix, a page table dumping (debug) fix and a clang
build fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/arm64: Fix fdt-related memory reservation
x86/mm: Apply the section attribute to the variable, not its type
x86/efi: Fixup GOT in all boot code paths
x86/efi: Only load initrd above 4g on second try
x86-64, ptdump: Mark espfix area only if existent
x86, irq: Fix build error caused by 9eabc99a63
