We only have direct access to MDIO on Falcon, so move this out of
struct efx_nic.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only have direct access to SPI on Falcon, so move all this state
out of struct efx_nic.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool EEPROM interface is really meant for exposing chip
configuration, not BootROM configuration.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the Falcon board config is invalid, we cannot proceed - we do not
have a valid board type to pass to falcon_probe_board(), and if we
kluge that to work with an unknown board then other initialisation
code will crash.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mcfw *never* sends CMDDONE when rebooting. Changing this so that it always
sends CMDDONE *before* REBOOT is easy on Siena, but it's not obvious that we
could guarantee to be able to implement this on future hardware.
Given this, I'm less convinced that the protocol should be changed.
To reiterate the failure mode: The driver sees this:
issue command
receive REBOOT event
Was that reboot event sent before the command was issued, or in
response to the command? If the former then there will be a subsequent
CMDDONE event, if the latter, then there will be no CMDDONE event.
Options to resolve this are:
1. REBOOT always completes an outstanding mcdi request, and we set
the credits count to ignore a subsequent CMDDONE event with
mismatching seqno.
2. REBOOT never completes an outstanding mcdi request. If there is
no CMDDONE event then we rely on the mcdi timeout code to complete
the outstanding request, incurring a 10s delay.
I'd argue that (2) is tidier, but that incurring a 10s delay is a little
needless. Let's go with (1).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we enable PMA/PMD loopback this automatically sets RXIN_SEL
(inverse polarity for RXIN). We need to clear that bit during the
soft-reset sequence, as it is not done automatically.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not want to shut down the board based on a fault that has
already been cleared.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set both the 'maximum' and critical temperature limits for LM87
hardware monitors on Falcon boards. Do not shut down a port until the
critical temperature is reached, but warn as soon as the 'maximum'
temperature is reached.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some errors are expected, e.g. when sending new commands to an MC
running old firmware. Only the caller of efx_mcdi_rpc() can decide
what is a real error. Therefore log the error responses with
netif_dbg().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delete unnecessary spin_lock for accessing Message Object.
Since all message objects are divided into tx/rx area completely,
spin_lock processing is unnecessary.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
For easy to readable, LEC #define macros are replaced to enums.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For easy to readable, add Message Object index like below.
PCH_RX_OBJ_START
PCH_RX_OBJ_END
PCH_TX_OBJ_START
PCH_TX_OBJ_END
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CAN register of Intel PCH EG20T has 2 sets of interface register.
To reduce whole of code size, separate interface register.
As a result, the number of function also can be reduced.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use strncpy instead of memcpy when working on strings
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove printks for ring blocks, fifo blocks, and rx doorbell mode as
they clutter the dmesg output during modprobe and provide no useful
information.
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NIC partitioning is another flavor of multi function - having few
PCI functions share the same physical port. Unlike the currently
supported mode of multi-function which depends on the switch
configuration and uses outer-VLAN, the NPAR mode is switch independent
and uses the MAC addresses to distribute incoming packets to the different
functions. This patch adds the specific HW setting of the NPAR mode
and some distinctions between switch dependent (SD) and
switch independent (SI) multi-function (MF) modes where the configuration
is not the same.
Advance driver version to 1.60.00-6
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the normal debugging functions.
Print mac address when using random_ether_addr.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These were probably just for initial driver debugging
and have not been enabled in builds in git history.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use vsprintf extension %pM for a mac address in one instance.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neaten the phy_init function by adding and calling vendor
specific functions.
object size is reduced by ~1kb:
$ size drivers/net/forcedeth.o.*
text data bss dec hex filename
83475 1848 19304 104627 198b3 drivers/net/forcedeth.o.new
84459 1848 19544 105851 19d7b drivers/net/forcedeth.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Deduplicate the code use for the init/reset of this device.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netdev_<level> when a struct net_device * is available.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert printks to pr_<level>.
Remove "forcedeth: " from some calls as it's now added by pr_fmt.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The remaining dprintk uses are emitted as KERN_INFO.
Change these dprintk uses to netdev_dbg.
Remove the now unused dprintk macros.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the more standard macro to preface netdev->name.
Fix casting on resource use.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the printk out of reg_delay and make
the callers emit a message on error.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If RSS is disabled, we can ifdef out some RSS specific code. This fixes
the compile error found by Randy Dunlap.
Signed-off-by: Scott J. Goldman <scottjg@vmware.com>
Reviewed-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tso hdr is longer then the regular l3 hdr. Fix the calculation
of the total len by accounting the size of the tso hdr.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device initialization of a qeth device contains a STARTLAN step.
This step may fail, if cable is not yet plugged in. The qeth device
stays in state HARDSETUP until cable is plugged in. This prevents
further preparational initialization steps of the qeth device and
its network interface. This patch makes sure initialization of qeth
device continues, even though cable is not yet plugged in.
Once carrier is available, qeth is notified, triggers a recovery
which results in a working network interface.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1d7138de87
igmp: RCU conversion of in_dev->mc_list
converted rwlock to RCU.
Update the s390 network drivers(qeth & lcs) code to adapt to this change.
V2 : Changes based on suggestions given by Eric Dumazet
Signed-off-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit to convert to use the dev_pm_ops struct
introduces a bug. The shutdown flag is not yet used
because the hibernation on memory is done by using
the freeze callback.
Thanks to Vlad for having reported it.
Reported-by: Vlad Lungu <vlad.lungu@windriver.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the ret variable is not used for anything other than
receive the value of the t3_adapter_error(), which will always be 0,
because the reset parameter is 0.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calculating the BD entry using a modulus operation isn't optimal, especially
inside the loop. This patch removes the modulus operations in favour of:
i) simply checking for wrapping in the case of cur_rx
ii) forcing num_tx to be a power of two and using it to mask out the
entry from cur_tx
The also prevents possible issues related overflow of the cur_rx and cur_tx
counters.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
