While developing the GPE reference counting code we overlooked the
fact that acpi_ev_update_gpes() could have enabled GPEs before
acpi_ev_initialize_gpe_block() was called. As a result, some GPEs
are enabled twice during the initialization.
To fix this issue avoid calling acpi_enable_gpe() from
acpi_ev_initialize_gpe_block() for the GPEs that have nonzero
runtime reference counters.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPICA uses acpi_hw_write_gpe_enable_reg() to re-enable a GPE after
an event signaled by it has been handled. However, this function
writes the entire GPE enable mask to the GPE's enable register which
may not be correct. Namely, if one of the other GPEs in the same
register was previously enabled by acpi_enable_gpe() and subsequently
disabled using acpi_set_gpe(), acpi_hw_write_gpe_enable_reg() will
re-enable it along with the target GPE.
To fix this issue rework acpi_hw_write_gpe_enable_reg() so that it
calls acpi_hw_low_set_gpe() with a special action value,
ACPI_GPE_COND_ENABLE, that will make it only enable the GPE if the
corresponding bit in its register's enable_for_run mask is set.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPICA uses acpi_ev_enable_gpe() for enabling GPEs at the low level,
which is incorrect, because this function only enables the GPE if the
corresponding bit in its enable register's enable_for_run mask is set.
This causes acpi_set_gpe() to work incorrectly if used for enabling
GPEs that were not previously enabled with acpi_enable_gpe(). As a
result, among other things, wakeup-only GPEs are never enabled by
acpi_enable_wakeup_device(), so the devices that use them are unable
to wake up the system.
To fix this issue remove acpi_ev_enable_gpe() and its counterpart
acpi_ev_disable_gpe() and replace acpi_hw_low_disable_gpe() with
acpi_hw_low_set_gpe() that will be used instead to manipulate GPE
enable bits at the low level. Make the users of acpi_ev_enable_gpe()
and acpi_ev_disable_gpe() call acpi_hw_low_set_gpe() instead and
make sure that GPE enable masks are only updated by acpi_enable_gpe()
and acpi_disable_gpe() when GPE reference counters change from 0
to 1 and from 1 to 0, respectively.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
In quite a few places ACPICA needs to compute a GPE enable mask with
only one bit, corresponding to a given GPE, set. Currently, that
computation is always open coded which leads to unnecessary code
duplication. Fix this by introducing a helper function for computing
one-bit GPE enable masks and using it where appropriate.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Commit 0f849d2cc6 (ACPICA: Minimize
the differences between linux GPE code and ACPICA code base)
introduced a change attempting to disable a GPE before installing
a handler for it in acpi_install_gpe_handler() which was incorrect.
First, the GPE disabled by it is never enabled again (except during
resume) which leads to battery insert/remove events not being
reported on the Maxim Levitsky's machine. Second, the disabled
GPE is still reported as enabled by the sysfs interface that only
checks its enable register's enable_for_run mask.
Revert this change for now, because it causes more damage to happen
than the bug it was supposed to fix.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We have ported Rafael's major GPE changes
(ACPI: Use GPE reference counting to support shared GPEs) into ACPICA code base.
But the port and Rafael's original patch have some differences, so we made
below patch to make linux GPE code consistent with ACPICA code base.
Most changes are about comments and coding styles.
Other noticeable changes are based on:
Rafael: Reduce code duplication related to GPE lookup
https://patchwork.kernel.org/patch/86237/
Rafael: Always use the same lock for GPE locking
https://patchwork.kernel.org/patch/90471/
A new field gpe_count in struct acpi_gpe_block_info to record the number
of individual GPEs in block.
Rename acpi_ev_save_method_info to acpi_ev_match_gpe_method.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Robert Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Some BIOS on Toshiba machines corrupt the DSDT, so add a new
boot option acpi=copy_dsdt to workaround it.
Add warning message to ask users to use this option if corrupt DSDT detected.
Also build a DMI blacklist to check it and automatically copy DSDT.
https://bugzilla.kernel.org/show_bug.cgi?id=14679
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Move initialization of DSDT pointer. Emit address of DSDT
in the dump of both table headers (good/bad DSDT).
Now handles the case where the root table can be reallocated,
which would invalidate the original pointer.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Optionally copy the entire DSDT to local memory (instead of
simply mapping it.) There are some BIOSs that corrupt or replace
the original DSDT, creating the need for this option. Default is
FALSE, do not copy the DSDT.
https://bugzilla.kernel.org/show_bug.cgi?id=14679
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This change adds support to detect a DSDT that has been corrupted
and/or replaced from outside the OS (by firmware). This is
typically catastrophic for the system, but has been seen on
some machines.
https://bugzilla.kernel.org/show_bug.cgi?id=14679
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The original implementation only supported reading from a DataTable
region. However, some machines have been seen that actually write
to the ACPI table contained in such a region. This change adds
support for writing to a DataTable region.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When copying the root table to the new allocation, the length
used was incorrect. The new size was used instead of the current
table size, meaning too much data was copied.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Also split some long lines.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixed a problem with the AML Mutex handling function
acpi_ex_release_mutex where the function could fault under the very
rare condition when the interpreter has blocked, the interpreter
lock is released, the interpreter is then reentered via the
same thread, and attempts to acquire a mutex that was previously
acquired. FreeBSD report 140979.
http://www.freebsd.org/cgi/query-pr.cgi?pr=140979
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Always use 0x prefix for hex output, use %u for integer output
(all integers are unsigned.)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This change will enable debug object output via a global variable,
acpi_gbl_enable_aml_debug_object. This will help with remote machine
debugging. Also, moved all debug object support code to a new
file, exdebug.c. Entire debug object module can now be
configured out of the ACPICA build if desired.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Commit b91ecb00 ("gigaset: include cleanup cleanup") removed an implicit
sched.h inclusion that came in via slab.h, and caused various compile
problems as a result.
This should fix it.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
gigaset: include cleanup cleanup
packet : remove init_net restriction
WAN: flush tx_queue in hdlc_ppp to prevent panic on rmmod hw_driver.
ip: Fix ip_dev_loopback_xmit()
net: dev_pick_tx() fix
fib: suppress lockdep-RCU false positive in FIB trie.
tun: orphan an skb on tx
forcedeth: fix tx limit2 flag check
iwlwifi: work around bogus active chains detection
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: add FireMV 2400 PCI ID.
drm/radeon/kms: allow R500 regs VAP_ALT_NUM_VERTICES and VAP_INDEX_OFFSET
drivers/gpu/radeon: Add MSPOS regs to safe list.
drm/radeon/kms: disable the tv encoder when tv/cv is not in use
drm/radeon/kms: adjust pll settings for tv
drm/radeon/kms: fix tv dac conflict resolver
drm/radeon/kms/evergreen: don't enable hdmi audio stuff
drm/radeon/kms/atom: fix dual-link DVI on DCE3.2/4.0
drm/radeon/kms: fix rs600 tlb flush
drm/radeon/kms: print GPU family and device id when loading
drm/radeon/kms: fix calculation of mipmapped 3D texture sizes
drm/radeon/kms: only change mode when coherent value changes.
drm/radeon/kms: more atom parser fixes (v2)
[airlied: fix V_A_N_V to not be safe and fix check to make sure only r500
- bump userspace version]
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Switching between TV and VGA caused VGA to break on some systems
since the TV encoder was left enabled when VGA was used.
fixes fdo bug 25520.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On systems with the tv dac shared between DVI and TV,
we can only use the dac for one of the connectors.
However, when using a digital monitor on the DVI port,
you can use the dac for the TV connector just fine.
Check the use_digital status when resolving the conflict.
Fixes fdo bug 27649, possibly others.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Got broken during the evergreen merge.
Fixes fdo bug 27001.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Typo in in flush leaded to no flush of the RS600 tlb which
ultimately leaded to massive system ram corruption, with
this patch everythings seems to work properly.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This will help figuring out GPU when looking at bugs log.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 5a0e3ad causes slab.h to be included twice in many of the
Gigaset driver's source files, first via the common include file
gigaset.h and then a second time directly. Drop the spares, and
use the opportunity to clean up a few more similar cases.
Impact: cleanup, no functional change
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
CC: Tejun Heo <tj@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Ignore LVDS EDID when it is unavailabe or invalid
drm/i915: Add no_lvds entry for the Clientron U800
drm/i915: Rename many remaining uses of "output" to encoder or connector.
drm/i915: Rename intel_output to intel_encoder.
agp/intel: intel_845_driver is an agp driver!
drm/i915: introduce to_intel_bo helper
drm/i915: Disable FBC on 915GM and 945GM.
tx_queue is used as a temporary queue when not allowed to queue skb
directly to the hw device driver (which may sleep). Most paths flush
it before returning, but ppp_start() currently cannot. Make sure we
don't leave skbs pointing to a non-existent device.
Thanks to Michael Barkowski for reporting this problem.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
access_bit_width field is u8 in ACPICA, thus 256 value written to it
becomes 0, causing divide by zero later.
Proper fix would be to remove access_bit_width at all, just because
we already have access_byte_width, which is access_bit_width / 8.
Limit access width to 64 bit for now.
https://bugzilla.kernel.org/show_bug.cgi?id=15749
fixes regression caused by the fix for:
https://bugzilla.kernel.org/show_bug.cgi?id=14667
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Correct fix for the "ioremap() causes build failure on S390" should have been
a dependancy on HAS_IOMEM. So we add this dependancy also (and leave the driver
in the ARM section for now).
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
When shutting down the watchdog timer, special care must be taken
not to overwrite other bits in the register, as it may be shared
with other peripherals.
For example, on the Arcom Vulcan, the register is shared between
the watchdog and the PCI reset line...
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
A previous fix changed the WDTP function to use the period directly,
rather than subtracting from 63. However the mask generation was
not changed, so the mask was coming out as 0. This patch fixes it.
Signed-off-by: Luuk Paulussen <luuk.paulussen@alliedtelesis.co.nz>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch allows Watchdog timer to be selected for OMAP4 by fixing
Kconfig entry
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - switch mode upon system resume
Revert "Input: wacom - merge out and in prox events"
Input: matrix_keypad - allow platform to disable key autorepeat
Input: ALPS - add signature for HP Pavilion dm3 laptops
Input: i8042 - spelling fix
Input: sparse-keymap - implement safer freeing of the keymap
Input: update the status of the Multitouch X driver project
Input: clarify the no-finger event in multitouch protocol
Input: bcm5974 - retract efi-broken suspend_resume
Input: sparse-keymap - free the right keymap on error
When Wacom devices wake up from a sleep, the switch mode command
(wacom_query_tablet_data) is needed before wacom_open is called.
wacom_query_tablet_data should not be executed inside wacom_open
since wacom_open is called more than once during probe.
wacom_retrieve_hid_descriptor is removed from wacom_resume due
to the fact that the required descriptors are stored properly
upon system resume.
Reported-and-tested-by: Anton Anikin <Anton@Anikin.name>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Cc: stable@kernel.org
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add the iMac9,1 and the MacBookPro2,2 temperature sensors to hwmon
driver applesmc to fix kernel bug #14429:
https://bugzilla.kernel.org/show_bug.cgi?id=14429
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Acked-by: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
When any temperature sensor type is changed, the corresponding
temperature value needs to be updated. The register caching mechanism
may delay this update, so we want to invalidate the cache to force an
immediate update.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Currently, if someone tries to set the thermal sensor type to an
unsupported value, subsequent accesses to the chip may temporarily
show the sensor in question as disabled. Use a temporary variable
and only update the cached value on success, to prevent such
confusion.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Temperature channels can be used in 2 different modes (thermistor and
thermal diode) and we don't know which one, if any, is correct for
every given board. So don't arbitrarily choose one. Instead, leave the
temperature channels untouched. They can be configured from user-space
if needed anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
When CONFIG_REGULATOR isn't set, regulator_get_voltage() returns 0.
Properly handle this case by not trusting the value.
Reported-by: Jerome Oufella <jerome.oufella@savoirfairelinux.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
I discovered two issues.
First the previous sht15_calc_temp() loop did not iterate through the
temppoints array since the (data->supply_uV > temppoints[i - 1].vdd)
test is always true in this direction.
Also the two-points linear interpolation function was returning biased
values due to a stray division by 1000 which shouldn't be there.
[JD: Also change the default value for d1 from 0 to something saner.]
Signed-off-by: Jerome Oufella <jerome.oufella@savoirfairelinux.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
This is a partial revert of 4cd8b5e2a1 "lguest: use KVM hypercalls";
we revert to using (just as questionable but more reliable) int $15 for
hypercalls. I didn't revert the register mapping, so we still use the
same calling convention as kvm.
KVM in more recent incarnations stopped injecting a fault when a guest
tried to use the VMCALL instruction from ring 1, so lguest under kvm
fails to make hypercalls. It was nice to share code with our KVM
cousins, but this was overreach.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Matias Zabaljauregui <zabaljauregui@gmail.com>
Cc: Avi Kivity <avi@redhat.com>
