This patch adds the initial support for pinctrl based on H407 SoC.
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds a new logic inside the st pinctrl to manage
an unsupported scenario: some sysconfig are not available!
This is the case of STiH407 where, although documented, the
following registers from SYSCFG_FLASH have been removed from the SoC.
SYSTEM_CONFIG3040
Output Enable pad control for all PIO Alternate Functions
and
SYSTEM_ CONFIG3050
Pull Up pad control for all PIO Alternate Functions
Without managing this condition an imprecise external abort
will be detect.
To do this the patch also reviews the st_parse_syscfgs
and other routines to manipulate the registers only if
actually available.
In any case, for example the st_parse_syscfgs detected
an error condition but no action was made in the
st_pctl_probe_dt.
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ST pin controller does not have hardware support for detecting edge
triggered interrupts, It only has level triggering support.
This patch attempts to fake up edge triggers from hw level trigger
support in software. With this facility now the gpios can be easily used
for keypads, otherwise it would be difficult for drivers like keypads to
work with level trigger interrupts.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch add interrupt support to the pincontroller driver.
ST Pincontroller GPIO bank can have one of the two possible types of
interrupt-wirings.
First type is via irqmux, single interrupt is used by multiple gpio
banks. This reduces number of overall interrupts numbers required. All
these banks belong to a single pincontroller.
_________
| |----> [gpio-bank (n) ]
| |----> [gpio-bank (n + 1)]
[irqN]-- | irq-mux |----> [gpio-bank (n + 2)]
| |----> [gpio-bank (... )]
|_________|----> [gpio-bank (n + 7)]
Second type has a dedicated interrupt per gpio bank.
[irqN]----> [gpio-bank (n)]
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Probe function had commas instead of semi-colons on some of the lines.
This patch just fixes those lines. No functional chagnes done in this
patch.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When setting pin configuration in the pinctrl framework, pin_config_set() or
pin_config_group_set() is called in a loop to set one configuration at a time
for the specified pin or group.
This patch 1) removes the loop and 2) changes the API to pass the whole pin
config array to the driver. It is now up to the driver to loop through the
configs. This allows the driver to potentially combine configs and reduce the
number of writes to pin config registers.
All c files changed have been build-tested to verify the change compiles and
that the corresponding .o is successfully generated.
Signed-off-by: Sherman Yin <syin@broadcom.com>
Reviewed-by: Christian Daudt <csd@broadcom.com>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Symbols used only in this file are made static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a DT only driver and st_pctl_of_match is always compiled
in. Hence of_match_ptr is unnecessary.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
In case of error, the function pinctrl_register() returns
NULL not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.
The function syscon_regmap_lookup_by_phandle() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch add pinctrl support to ST SoCs.
About hardware:
ST Set-Top-Box parts have two blocks called PIO and PIO-mux which handle
pin configurations.
Each multi-function pin is controlled, driven and routed through the PIO
multiplexing block. Each pin supports GPIO functionality (ALT0) and
multiple alternate functions(ALT1 - ALTx) that directly connect the pin
to different hardware blocks. When a pin is in GPIO mode, Output Enable
(OE), Open Drain(OD), and Pull Up (PU) are driven by the related PIO
block. Otherwise the PIO multiplexing block configures these parameters
and retiming the signal.
About driver:
This pinctrl driver manages both PIO and PIO-mux block using pinctrl,
pinconf, pinmux, gpio subsystems. All the pinctrl related config
information can only come from device trees.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>