Pad retention control after suspend/resume cycle should be done from pin
controller driver instead of PMU (power management unit) driver to avoid
possible ordering and logical dependencies. Till now it worked fine only
because PMU driver registered its sys_ops after pin controller.
This patch adds infrastructure to handle pad retention during pin control
driver resume.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Support for Exynos4415 is going away because there are no internal nor
external users.
Since commit 46dcf0ff0d ("ARM: dts: exynos: Remove exynos4415.dtsi"),
the platform cannot be instantiated so remove also the drivers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch supports the multiple IORESOURCE_MEM resources for one pin-bank.
In the pre-existing Exynos series, the registers of the gpio bank are included
in the one memory map. But, some gpio bank need to support the one more memory
map (IORESOURCE_MEM) because the registers of gpio bank are separated into
the different memory map.
For example,
The both ALIVE and IMEM domain have the different memory base address.
The GFP[1-5] of exynos5433 are composed as following:
- ALIVE domain : WEINT_* registers
- IMEM domain : CON/DAT/PUD/DRV/CONPDN/PUDPDN register
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: linux-gpio@vger.kernel.org
Suggested-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add Samsung EXYNOS5410 SoC specific data to enable pinctrl
support for all platforms based on EXYNOS5410.
Signed-off-by: Hakjoo Kim <ruppi.kim@hardkernel.com>
[AF: Rebased onto Exynos5260, irq_chip consolidation, const'ification]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Tested-by: Pavel Fedin <p.fedin@samsung.com>
[k.kozlowski: Rebased on current v4.3]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch adds driver data for Exynos5433 SoC. Exynos5433 includes 228 multi-
functional input/output port pins and 135 memory port pins. There are 41 general
port groups and 2 memory port groups.
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin controllers of Exynos4415 are similar to Exynos4412, but certain
differences cause the need to create separate driver data for it. This
patch adds pin controller and bank descriptor arrays to the driver to
support the new SoC.
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
[cw00.choi: Rebase it on mainline kernel]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
[tomasz.figa@gmail.com: Resolved merge with earlier clean-up series.]
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
This patch adds initial driver data for Exynos7 pinctrl support.
Signed-off-by: Naveen Krishna Ch <naveenkrishna.ch@gmail.com>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Reviewed-by: Thomas Abraham <thomas.ab@samsung.com>
Tested-by: Thomas Abraham <thomas.ab@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
The function exynos_irq_demux_eint16_31 uses pre-defined offsets for external
interrupt pending status and mask registers. So this function is not extensible
for Exynos7 SoC which has these registers at different offsets. Generalize
the exynos_irq_demux_eint16_31 function by using the pending/mask register
offset values from the exynos_irq_chip structure. This is done by adding a
irq_chip field to the samsung_pin_bank struct.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Reviewed-by: Thomas Abraham <thomas.ab@samsung.com>
Tested-by: Thomas Abraham <thomas.ab@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Currently the driver mixes constant init data with runtime data, which
is far from being elegant and can invite potential hard to track issues.
This patch intends to solve this by introducing a new
samsung_pin_bank_data structure to hold only constant data known at
compile time, which can be copied to main samsung_pin_bank struct used
at runtime.
In addition, thanks to this change, all per-bank initdata can be marked
with const and __initconst keywords and dropped after init completes.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
In order to separate initialization constants from runtime data, this
patch modifies the driver to store only constant data in
samsung_pin_ctrl struct and copy data required at runtime to
samsung_pinctrl_drv_data struct. This makes it possible to mark all
existing instances of samsung_pin_ctrl struct as const and __initconst.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
This structure is not intended to be modified at runtime and functions
as constant data shared between multiple pin banks. This patch makes all
instances of it constant across the driver.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
There is no code using it and in fact there are pin controller variants
that do not even have this field initialized in their init data. This
patch removes it completely.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Currently after configuring a GPIO pin as an interrupt related pinmux
registers are changed, but there is no protection from calling
gpio_direction_*() in a badly written driver, which would cause the same
pinmux register to be reconfigured for regular input/output and this
disabling interrupt capability of the pin.
This patch addresses this issue by moving pinmux reconfiguration to
.irq_{request,release}_resources() callback of irq_chip and calling
gpio_lock_as_irq() helper to prevent reconfiguration of pin direction.
Setting up a GPIO interrupt on Samsung SoCs is a two-step operation -
in addition to trigger configuration in a dedicated register, the pinmux
must be also reconfigured to GPIO interrupt, which is a different function
than normal GPIO input, although I/O-wise they both behave in the same way
and gpio_get_value() can be used on a pin configured as IRQ as well.
Such design implies subtleties such as gpio_direction_input() not having
to fail if a pin is already configured as an interrupt nor change the
configuration to normal input. But the FLAG_USED_AS_IRQ set in gpiolib by
gpio_lock_as_irq() is only used to check that gpio_direction_output() is
not called, it's not used to prevent gpio_direction_input() to be called.
So this is not a complete solution for Samsung SoCs but it's definitely a
move in the right direction.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
[javier: use request resources instead of startup and expand commit message]
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Group all pin control drivers of Samsung platform together in
a sub-directory for easy maintenance.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
