We use decimal for all the other RP magic values, so change
GEN6_RP_DOWN_TIMEOUT to decimal as well. Also change the order
of the register writes to match the BIOS spec for easier verification.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Deepak S<deepak.s@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Follow the sequence in the BIOS spec and clear the RC_CONTROL register
before changing any of the other RC6/RP registers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Deepak S<deepak.s@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use new Sideband offset to read max/min/gaur freq based on the SKU it
is running on. Based on the Number of EU, we read different bits to
identify the max frequencies at which system can run.
v2: reuse mask definitions & INTEL_INFO() to get device info (Ville)
v3: add break in switch conditions (Ville)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala at linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- refactor i915/snd-hda interaction to use the component framework (Imre)
- psr cleanups and small fixes (Rodrigo)
- a few perf w/a from Ken Graunke
- switch to atomic plane helpers (Matt Roper)
- wc mmap support (Chris Wilson & Akash Goel)
- smaller things all over
* tag 'drm-intel-next-2015-01-17' of git://anongit.freedesktop.org/drm-intel: (40 commits)
drm/i915: Update DRIVER_DATE to 20150117
i915: reuse %ph to dump small buffers
drm/i915: Ensure the HiZ RAW Stall Optimization is on for Cherryview.
drm/i915: Enable the HiZ RAW Stall Optimization on Broadwell.
drm/i915: PSR link standby at debugfs
drm/i915: group link_standby setup and let this info visible everywhere.
drm/i915: Add missing vbt check.
drm/i915: PSR HSW/BDW: Fix inverted logic at sink main_link_active bit.
drm/i915: PSR VLV/CHV: Remove condition checks that only applies to Haswell.
drm/i915: VLV/CHV PSR needs to exit PSR on every flush.
drm/i915: Fix kerneldoc for i915 atomic plane code
drm/i915: Don't pretend SDVO hotplug works on 915
drm/i915: Don't register HDMI connectors for eDP ports on VLV/CHV
drm/i915: Remove I915_HAS_HOTPLUG() check from i915_hpd_irq_setup()
drm/i915: Make hpd arrays big enough to avoid out of bounds access
Revert "drm/i915/chv: Use timeout mode for RC6 on chv"
drm/i915: Improve HiZ throughput on Cherryview.
drm/i915: Reset CSB read pointer in ring init
drm/i915: Drop unused position fields (v2)
drm/i915: Move to atomic plane helpers (v9)
...
Backmerge Linus tree after rc5 + drm-fixes went in.
There were a few amdkfd conflicts I wanted to avoid,
and Ben requested this for nouveau also.
Conflicts:
drivers/gpu/drm/amd/amdkfd/Makefile
drivers/gpu/drm/amd/amdkfd/kfd_chardev.c
drivers/gpu/drm/amd/amdkfd/kfd_mqd_manager.c
drivers/gpu/drm/amd/amdkfd/kfd_priv.h
drivers/gpu/drm/amd/include/kgd_kfd_interface.h
drivers/gpu/drm/i915/intel_runtime_pm.c
drivers/gpu/drm/radeon/radeon_kfd.c
This reverts commit 5a0afd4b78.
Although timeout mode allows higher residency it impact badly on performance.
I believe while we don't have a way to balance between performance and
power savings at runtime I believe we have to revert and prioritize
performance that was impacted a lot.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88103
Cc: Deepak S <deepak.s@linux.intel.com>
Cc: Wendy Wang <wendy.wang@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Conflicts:
drivers/gpu/drm/i915/intel_runtime_pm.c
Separate branch so that Takashi can also pull just this refactoring
into sound-next.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
We apply the RPS interrupt workaround on VLV everywhere except when
writing the mask directly during idling the GPU. For consistency do this
also there.
While at it also extend the code comment about affected platforms.
I couldn't reproduce the issue on VLV fixed by this workaround, by
removing the workaround from everywhere, while it's 100% reproducible on
SNB using igt/gem_reset_stats/ban-ctx-render. So also add a note that
it hasn't been verified if the workaround really applies to VLV/CHV.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In
commit dbea3cea69
Author: Imre Deak <imre.deak@intel.com>
Date: Mon Dec 15 18:59:28 2014 +0200
drm/i915: sanitize RPS resetting during GPU reset
we disable RPS interrupts during GPU resetting, but don't apply the
necessary GEN6 HW workaround. This leads to a HW lockup during a
subsequent "looping batchbuffer" workload. This is triggered by the
testcase that submits exactly this kind of workload after a simulated
GPU reset. I'm not sure how likely the bug would have triggered
otherwise, since we would have applied the workaround anyway shortly
after the GPU reset, when enabling GT powersaving from the deferred
work.
This may also fix unrelated issues, since during driver loading /
suspending we also disable RPS interrupts and so we also had a short
window during the rest of the loading / resuming where a similar
workload could run without the workaround applied.
v2:
- separate the fix to route RPS interrupts to the CPU on GEN9 too
to a separate patch (Daniel)
Bisected-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Testcase: igt/gem_reset_stats/ban-ctx-render
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=87429
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
GEN8+ HW has the option to route PM interrupts to either the CPU or to
GT. For GEN8 this was already set correctly to routing to CPU, but not
for GEN9, so fix this. Note that when disabling RPS interrupts this was
set already correctly, though in that case it didn't matter much except
for the possibility of spurious interrupts.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
- plane handling refactoring from Matt Roper and Gustavo Padovan in prep for
atomic updates
- fixes and more patches for the seqno to request transformation from John
- docbook for fbc from Rodrigo
- prep work for dual-link dsi from Gaurav Signh
- crc fixes from Ville
- special ggtt views infrastructure from Tvrtko Ursulin
- shadow patch copying for the cmd parser from Brad Volkin
- execlist and full ppgtt by default on gen8, for testing for now
* tag 'drm-intel-next-2014-12-19' of git://anongit.freedesktop.org/drm-intel: (131 commits)
drm/i915: Update DRIVER_DATE to 20141219
drm/i915: Hold runtime PM during plane commit
drm/i915: Organize bind_vma funcs
drm/i915: Organize INSTDONE report for future.
drm/i915: Organize PDP regs report for future.
drm/i915: Organize PPGTT init
drm/i915: Organize Fence registers for future enablement.
drm/i915: tame the chattermouth (v2)
drm/i915: Warn about missing context state workarounds only once
drm/i915: Use true PPGTT in Gen8+ when execlists are enabled
drm/i915: Skip gunit save/restore for cherryview
drm/i915/chv: Use timeout mode for RC6 on chv
drm/i915: Add GPGPU_THREADS_DISPATCHED to the register whitelist
drm/i915: Tidy up execbuffer command parsing code
drm/i915: Mark shadow batch buffers as purgeable
drm/i915: Use batch length instead of object size in command parser
drm/i915: Use batch pools with the command parser
drm/i915: Implement a framework for batch buffer pools
drm/i915: fix use after free during eDP encoder destroying
drm/i915/skl: Skylake also supports DP MST
...
Haswell significantly improved the performance of sampler_c messages,
but the optimization appears to be off by default. Later platforms
remove this bit, and apparently always enable the optimization.
Improves performance in "Counter Strike: Global Offensive" by 18%
at default settings on Iris Pro.
This may break sampling of paletted formats (P8/A8P8/P8A8). It's
unclear whether it affects sampling of paletted formats in general,
or just the sample_c message (which is never used).
While libva does have support for using paletted formats (primarily
for OSDs), that support appears to have been broken for at least a
year, so I couldn't observe a regression from this:
I tried to get libva-intel to use paletted formats, and observe a
regression...but the only thing I found that used it was mplayer's OSD
(on screen display). Even without my patch, the colors were totally
wrong with that, and it's according to a few distro wikis, that's been
the case for over a year.
If libva's code for paletted formats /is/ broken, they could always
add code to disable this bit using the command validator when fixing
it.
Further investigation from Haihao shows that libva mplayer OSD seems
to work at least on his setup (still unclear what's wron with Ken's),
and that it's not affected by this patch. Quoting the discussion
between Haihao and Ken:
> > > If you use "-vo gl" or "-vo xv", the OSD is solid white text with a black
> > > border around it. I presume that it's supposed to be white with vaapi as
> > > well, but I guess I'm not entirely sure.
> > >
> > > It's possible that the optimization doesn't affect the palette as long as
> > > you never use sample_c with the paletted textures.
> >
> > I verified the palette takes effect in the following way:
> >
> > 1. Only support P8A8 format in the driver
> >
> > 2. ran the above command and I saw white OSD text
> >
> > 3. Only support P4A4 format in the driver and don't use
> > 3DSTATE_SAMPLER_PALETTE_LOAD0 to load the value to the texture palette,
> > so the palette keeps unchanged.
> >
> > 4. ran the above command and I saw black OSD text.
> >
> > 5. Load the right value to the texture palette and ran the above command
> > again, I saw white OSD text.
> >
> > Hence I think sample_c with the paletted textures is used in the driver.
>
> That sounds like the palette is actually working, then. Great :)
>
> I doubt that libva would use sample_c - sampling with a shadow comparison?
> It looks like it just uses sample and sample+killpix.
You are right, libva driver doesn't use sample_c message.
> I'm pretty sure the sample_c optimization just uses the palette memory as
> storage for some stuff, so it's quite possible it just works if you're
> only using sample and sample+killpix.
Thanks for the explanation, it makes sense to me.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
[danvet: Add wa name from Ville's review to the comment and copypaste
the explanation why we don't care about libva (already broken) from
Ken. Also add conclusion from libva devs that&why this is all fine.]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: "Xiang, Haihao" <haihao.xiang@intel.com>
Cc: libva@lists.freedesktop.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Higher RC6 residency is observed using timeout mode
instead of EI mode. It's Recommended to use TO Method for RC6.
v2: Add comment about timeout threshold. (Tom)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm, we don't disable RPS interrupts and related work items before
resetting the GPU. This may interfere with the following GPU
initialization and cause RPS interrupts to show up in PM_IIR too early
before calling gen6_enable_rps_interrupts() (triggering a WARN there).
Solve this by disabling RPS interrupts and flushing any related work
items before resetting the GPU.
v2:
- split out the common parts of the gt suspend and the new gt reset
functions (Paulo)
v3:
- remove the check for UMS, it's a NOP nowadays (Daniel)
Reported-by: He, Shuang <shuang.he@intel.com>
Testcase: igt/gem_reset_stats/ban-render
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=86644
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We were incorreectly bypassing the flush everytime which led to fifo
underrun when more than one plane is enabled.
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Satheeshakrishna M<satheeshakrishna.m@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The pipe wm parameters is not correctly updated with sprite parameters
because it copies them for each plane from plane_list to the sprite
offset in pipe wm parameters. Since plane_list also contains primary and
cursor planes, we end up updating wrong params for sprites.
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No functional changes. This is just the begin of a FBC rework.
v2 (Paulo):
- Revert intel_fbc_init() changed parameter.
- Revert set_no_fbc_reason() rename.
- Rebase.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I was playing with clang and oh surprise! a warning trigerred by
-Wshift-overflow (gcc doesn't have this one):
WA_SET_BIT_MASKED(GEN7_GT_MODE,
GEN6_WIZ_HASHING_MASK | GEN6_WIZ_HASHING_16x4);
drivers/gpu/drm/i915/intel_ringbuffer.c:786:2: warning: signed shift result
(0x28002000000) requires 43 bits to represent, but 'int' only has 32 bits
[-Wshift-overflow]
WA_SET_BIT_MASKED(GEN7_GT_MODE,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/i915/intel_ringbuffer.c:737:15: note: expanded from macro
'WA_SET_BIT_MASKED'
WA_REG(addr, _MASKED_BIT_ENABLE(mask), (mask) & 0xffff)
Turned out GEN6_WIZ_HASHING_MASK was already shifted by 16, and we were
trying to shift it a bit more.
The other thing is that it's not the usual case of setting WA bits here, we
need to have separate mask and value.
To fix this, I've introduced a new _MASKED_FIELD() macro that takes both the
(unshifted) mask and the desired value and the rest of the patch ripples
through from it.
This bug was introduced when reworking the WA emission in:
Commit 7225342ab5
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Tue Oct 7 17:21:26 2014 +0300
drm/i915: Build workaround list in ring initialization
v2: Invert the order of the mask and value arguments (Daniel Vetter)
Rewrite _MASKED_BIT_ENABLE() and _MASKED_BIT_DISABLE() with
_MASKED_FIELD() (Jani Nikula)
Make sure we only evaluate 'a' once in _MASKED_BIT_ENABLE() (Dave Gordon)
Add check to ensure the value is within the mask boundaries (Chris Wilson)
v3: Ensure the the value and mask are 16 bits (Dave Gordon)
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The conversion table can be replaced with simple enough function.
text data bss dec hex filename
839688 10987 24 850699 cfb0b drivers/gpu/drm/i915/i915.ko
839224 10987 24 850235 cf93b drivers/gpu/drm/i915/i915.ko
Result is 494 saved bytes (.05525%).
v2: - no run on sentences from subject (Chris, Jani)
- be verbose about the savings (Chris, Daniel)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This function can be called now with i915 interrupts enabled, so the
corresponding WARN is incorrect, remove it. I think this was spotted by
Paulo during his review, but since I already removed the same WARN
from intel_suspend_gt_powersave() I missed then his point.
Spotted-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I saw punit timeouts in vlv_set_rps_idle() while running various
subtests of pm_rpm. Increasing the timeout to 100ms got rid of the
issue.
Testcase: igt/pm_rpm
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=82939
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Guo Jinxian <jinxianx.guo@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In __gen6_update_ring_freq, use the full range of
possible gpu frequencies from max_freq to min_freq.
The actual gpu frequency could be outside the range
from max_freq_softlimit to min_freq_softlimit due
to power/thermal constraints.
Signed-off-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In gen8_enable_rps, change the initial rps setting
to the min_freq_softlimit (same as gen6_enable_rps).
Signed-off-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Set the min_freq_softlimit to max(RPe, 450MHz).
Setting a floor can ensure a minimum experience
level. The 450MHz value came from a power and
performance study of various types of workloads
(3D, Media, GPGPU, idle, etc).
v2: rebased
Signed-off-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added gen6_init_rps_frequencies() to initialize
the rps frequency values. This function replaces
parse_rp_state_cap(). In addition to reading RPn,
RP0, and RP1 from RP_STATE_CAP register, the new
function reads efficient frequency (aka RPe) from
pcode for Haswell and Broadwell and sets the turbo
softlimits. The turbo minimum frequency softlimit
is set to RPe for Haswell and Broadwell and to RPn
otherwise.
For RPe, the efficiency is based on the frequency/power
ratio (MHz/W); this is considering GT power and not
package power. The efficent frequency is the highest
frequency for which the frequency/power ratio is within
some threshold of the highest frequency/power ratio.
A fixed decrease in frequency results in smaller
decrease in power at frequencies less than RPe than
at frequencies above RPe.
v2: Following suggestions from Chris Wilson and
Daniel Vetter to extend and rename parse_rp_state_cap
and to open-code a poorly named function.
Signed-off-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Remove unused variables.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So with all the code movement and extraction in intel_pm.c in -next
git is hopelessly confused with
commit 2208d655a9
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Nov 14 09:25:29 2014 +0100
drm/i915: drop WaSetupGtModeTdRowDispatch:snb
from -fixes. Worse even small changes in -next move around the
conflict context so rerere is equally useless. Let's just backmerge
and be done with it.
Conflicts:
drivers/gpu/drm/i915/i915_drv.c
drivers/gpu/drm/i915/intel_pm.c
Except for git getting lost no tricky conflicts really.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
After the previous patch RPS disabling doesn't depend any more on the
first level interrupts being disabled, so we can move it everywhere
earlier. Doing so let's us think about the uninitialization steps
afterwards independently of any asynchronous RPS events that can happen
atm. It also makes the system/runtime suspend time RPS disabling more
uniform. Finally this gets rid of the WARN in
intel_suspend_gt_powersave(), which we can hit if a final RPS work runs
after we disabled the first level interrupts.
Testcase: igt/pm_rpm
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=82939
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When disabling the RPS interrupts there is a tricky dependency between
the thread disabling the interrupts, the RPS interrupt handler and the
corresponding RPS work. The RPS work can reenable the interrupts, so
there is no straightforward order in the disabling thread to (1) make
sure that any RPS work is flushed and to (2) disable all RPS
interrupts. Currently this is solved by masking the interrupts using two
separate mask registers (first level display IMR and PM IMR) and doing
the disabling when all first level interrupts are disabled.
This works, but the requirement to run with all first level interrupts
disabled is unnecessary making the suspend / unload time ordering of RPS
disabling wrt. other unitialization steps difficult and error prone.
Removing this restriction allows us to disable RPS early during suspend
/ unload and forget about it for the rest of the sequence. By adding a
more explicit method for avoiding the above race, it also becomes easier
to prove its correctness. Finally currently we can hit the WARN in
snb_update_pm_irq(), when a final RPS work runs with the first level
interrupts already disabled. This won't lead to any problem (due to the
separate interrupt masks), but with the change in this and the next
patch we can get rid of the WARN, while leaving it in place for other
scenarios.
To address the above points, add a new RPS interrupts_enabled flag and
use this during RPS disabling to avoid requeuing the RPS work and
reenabling of the RPS interrupts. Since the interrupt disabling happens
now in intel_suspend_gt_powersave(), we will disable RPS interrupts
explicitly during suspend (and not just through the first level mask),
but there is no problem doing so, it's also more consistent and allows
us to unify more of the RPS disabling during suspend and unload time in
the next patch.
v2/v3:
- rebase on patch "drm/i915: move rps irq disable one level up" in the
patchset
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm we first enable the RPS interrupts then we clear any pending ones.
By this we could lose an interrupt arriving after we unmasked it. This
may not be a problem as the caller should handle such a race, but logic
still calls for the opposite order. Also we can delay enabling the
interrupts until after all the RPS initialization is ready with the
following order:
1. disable left-over RPS (earlier via intel_uncore_sanitize)
2. clear any pending RPS interrupts
3. initialize RPS
4. enable RPS interrupts
This also allows us to do the 2. and 4. step the same way for all
platforms, so let's follow this order to simplifying things.
Also make sure any queued interrupts are also cleared.
v2:
- rebase on the GEN9 patches where we don't support RPS yet, so we
musn't enable RPS interrupts on it (Paulo)
v3:
- avoid enabling RPS interrupts on GEN>9 too (Paulo)
- clarify the RPS init sequence in the log message (Chris)
- add POSTING_READ to gen6_reset_rps_interrupts() (Paulo)
- WARN if any PM_IIR bits are set in gen6_enable_rps_interrupts()
(Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We disable the RPS interrupts for all platforms at the same spot, so
move it one level up in the callstack to simplify things.
No functional change.
v2:
- rebase on the GEN9 patches where RPS isn't supported yet, so we don't
need to disable RPS interrupts on it (Paulo)
v3:
- avoid disabling the interrupts on GEN>9 too (Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In sandybridge_pcode_read and sandybridge_pcode_write,
extend the mbox parameter from u8 to u32.
On Haswell and Sandybridge, bits 7:0 encode the mailbox
command and bits 28:8 are used for address control for
specific commands.
Based on suggestion from Ville Syrjälä.
Signed-off-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to "Cherryview_GFXclocks_y14w36d1.xlsx" the GPU frequency
divider should be 10 in when the CZ clock is 400 MHz. Change the code
to agree so that we report the correct frequencies.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The divider used in the GPU frequency calculations is compatible between
vlv and chv. vlv just wants doubled values compared to chv.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Always print the final PCBR register value on both vlv and chv, and
also tell us whether the BIOS was a good citizen or not.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our freq<->opcode conversions assume that GPLL is always used.
Apparently that should be the case always, but let's scream if we
ever encounter something different.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove the magic number for the GPLLENABLE bit by adding a name for it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Even with the rps debug messages signficantly recuced by
commit 67956867aa
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Tue Sep 2 15:12:17 2014 +0300
drm/i915: Don't spam dmesg with rps messages on vlv/chv
we still get an inordinate amount of spam from this. Just kill the debug
print. If someone wants to observe it they can just use the tracepoint.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts the regressing
commit 6547fbdbff
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Dec 14 23:38:29 2012 +0100
drm/i915: Implement WaSetupGtModeTdRowDispatch
that causes GPU hangs immediately on boot.
Reported-by: Leo Wolf <jclw@ymail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79996
Cc: stable@vger.kernel.org (v3.8+)
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
[Jani: amended the commit message slightly.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Given the history, there's some chance we'll keep the same WM code for a
bit (previously, we were able to reuse the same WM code from ILK to BDW,
so that sounds like a fair assumption).
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville found out that the DATA1 register exists since SNB with some
scarce apparitions in the specs throughout the times. In his own words:
Also according to Bspec the mailbox data1 register already existed
since snb. The hsw cdclk change sequence also mentions that it should
be set to 0, but eg. the bdw IPS sequence doesn't mention it. I guess
in theory some pcode command might cause it to be clobbered, so I'm
thinking we should just explicitly set it to 0 for all platforms in
the pcode read/write functions
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When reading a CCK register we should obviously read it from CCK not
Punit. This problem has been present ever since this of code was
introduced in
commit 67c3bf6f55
Author: Deepak S <deepak.s@linux.intel.com>
Date: Thu Jul 10 13:16:24 2014 +0530
drm/i915: populate mem_freq/cz_clock for chv
The problem was raised during review by Mika [1] but somehow slipped
through the cracks, and the patch got applied with the problem unfixed.
[1] http://lists.freedesktop.org/archives/intel-gfx/2014-July/048937.html
Cc: Deepak S <deepak.s@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The logical place for these functions is in i915_irq.c next to the rest of
PM interrupt handling functions.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The GEN6 and GEN8 versions differ only in the PM IIR and IER register
addresses and that on GEN8 we need to keep the
GEN8_PMINTR_REDIRECT_TO_NON_DISP PM interrupt unmasked. Abstract away
these 3 things in the GEN6 versions of the helpers and use them
everywhere.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The helpers to enable/disable PM IRQs for GEN6 and GEN8 are the same
except for the PM interrupt mask register, so abstract away this
register in the GEN6 versions and use these everywhere.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-WaDisableDopClockGating:chv
-WaDisableSamplerPowerBypass:chv
-WaDisableGunitClockGating:chv
-WaDisableFfDopClockGating:chv
-WaDisableDopClockGating:chv
v2: Remove pre-production WA instead of restricting them
based on revision id (Ville)
For: VIZ-4090
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Configure and enable RC6 for Gen9.
v2: Rebase on top of BDW rc6 support (Damien)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Zhe Wang <zhe1.wang@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we write new values for the DDB allocation and WM parameters, we now
need to trigger the double buffer update for the pipe to take the new
configuration into account.
As the DDB is a global resource shared between planes, enabling or
disabling one plane will result in changes for all planes that are
currently in use, thus the need write PLANE_SURF/CUR_BASE for more than
the plane we're touching.
v2: Don't wait for pipes that are off
v3: Split the staging results structure to not exceed the 1Kb stack
allocation in skl_update_wm()
v4: Rework and document the algorithm after Ville found that it was all
wrong.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To correctly flush the new DDB allocation we need to know about the pipe
allocation layout inside the DDB in order to sequence the re-allocation
to not cause a newly allocated pipe to fetch from a space that was
previously allocated to another pipe.
This patch preserves the per-pipe (start,end) allocation to be used in
the flush.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
