Found this problem when testing IPv6 from a KVM guest to a remote
host via e1000e device on the host.
The following patch fixes the check for IPv6 GSO packet in Intel
ethernet drivers to use skb_is_gso_v6(). SKB_GSO_DODGY is also set
when packets are forwarded from a guest.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inadequate coordination between the PF driver and the VF driver results
in tx hangs in the VF driver when you perform certain actions that will
lead to a re-init of the PF. Add feature to notify active VFs when the PF
is about to re-initialize so that the VFs can take appropriate action.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF Reset Done bit should not be set in the extended control register
until the PF has actually completed the bring up process. It is a mis-
interpretation of the purpose of this bit to assume it should be set
when the physical reset of the device is done. Instead it should be used
to indicate to the VFs when the PF is ready to provide them with required
services. This is not until after the PF is finished coming up and ready
to process mailbox events.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This data storage for SW emulated MAC addresses is unlikely to ever be used
so pull it.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VFs are allocated (as indicated by adapter->num_vfs is non-zero) then
the PF pool is no longer zero. Instead it will be the same as the number
of VFs allocated. When setting the VLVF entry for the PF we need to use
the correct pool otherwise the PF will get VLAN packets from the wire
because the packet will pass VFTA filtering and the PF has the default
pool, but it will not get VLAN packets from the VFs because it has
not set the correct pool bit in the VLVF entry.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable count and i are unsigned so the (<|>=)0 tests do not work.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resolves issues seen when running netconsole and rebooting via
reboot -f. The issue was due to the fact that we were attempting to
perform interrupt actions when the q_vectors and rings had already been
freed via the ixgbe_shutdown routines.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Skip MAC loopback test when the adapter is set to a VT mode such as SR-IOV
or VMDq
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds SR-IOV features supported by the 82599 controller to the main driver
module. If the CONFIG_PCI_IOV kernel option is selected then the SR-IOV
features are enabled. Use the max_vfs module option to allocate up to 63
virtual functions per physical port.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds code to the core 82599 module to support SR-IOV features of the 82599
network controller
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the mailbox and SR-IOV feature modules to the ixgbe driver Makefile.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This module and header file add functions to support SR-IOV features of the
82599 10Gbe controller.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds register definitions, bit definitions and structures used by
the driver to support SR-IOV features of the 82599 controller.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 82599 virtual function device and the master 82599 physical function
device implement a mailbox utility for communication between the devices
using some SRAM scratch memory and a doorbell/answering mechanism enabled
via interrupt and/or polling. This C module and accompanying header
file implement the base functions for use of this feature.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEFINE_PCI_DEVICE_TABLE() so we get place PCI ids table into correct section
in every case.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tc is still throwing a warning that is could be used
uninitialized. This fixes it, and properly formats the device ID
checks for the use of this variable.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the %pM kernel extension to display the MAC address.
The only difference in the output is that the MAC address is
shown in the usual colon-separated hex notation.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a pci_save_state() call in ixgbe_resume() after
pci_restore_state(). A similar change was made in ixgbe_io_slot_reset()
that accommodates pci_restore_state() new behavior. This change makes
pci_restore_state() clear the saved_state flag This is necessary due
to a resent kernel change to pci_restore_state() so that it now clears
the saved_state flag of the device right after the device.s standard
configuration registers have been poplulated with the previously saved
values.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the 82598 is fed 802.1q packets, it chokes with
an error of the form:
ixgbe: eth0: ixgbe_tx_csum: partial checksum but proto=81!
As the logic there was not smart enough to look into
the vlan header to pick out the encapsulated protocol.
There are times when we'd like to send these packets
out without having to configure a vlan on the interface.
Here we check for the vlan tag and allow the packet to
go out with the correct hardware checksum.
This patch is a clone of a previously submitted patch by
Arthur Jones <ajones@riverbed.com> for igb (Commit -
fa4a7ef36e).
Signed-off-by: Gurucharan Shetty <gshetty@riverbed.com>
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modified patch with Dave's comments to replace mdelay with proper msleep.
Fix 82598 copper link issue, where the phy prematurely indicates link
before it is ready to process packets. The new function looks for phy
link and indicates that, when it is available. If phy is not ready
within few seconds of MAC indicating link, the function will return
failure which translates to link down indication.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the restart_queue and non_eop_desc counters from being
double-counted. They are cumulative in each ring, so we don't want to
add them to the cumulative result in the adapter's master counter.
Otherwise, the stats will be inaccurate
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is an updated version, because ixgbe_get_ethtool_stats()
needs to call dev_get_stats() or "ethtool -S" wont give
correct tx_bytes/tx_packets values.
Several cpus can update netdev->stats.tx_bytes & netdev->stats.tx_packets
in parallel. In this case, TX stats are under estimated and false sharing
takes place.
After a pktgen session sending exactly 200000000 packets :
# ifconfig fiber0 | grep TX
TX packets:198501982 errors:0 dropped:0 overruns:0 carrier:0
Multi queue devices should instead use txq->tx_bytes & txq->tx_packets
in their xmit() method (appropriate txq lock already held by caller, no
cache line miss), or use appropriate locking.
After patch, same pktgen session gives :
# ifconfig fiber0 | grep TX
TX packets:200000000 errors:0 dropped:0 overruns:0 carrier:0
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when disabling interrupts, driver was writing with IO, this is no
necessary because on ixgbe parts the hardware can "oneshot"
disable and clear the interrupt. So on 82598/82599 use of EIAM
should avoid one posted write per interrupt when in MSI-X mode.
This should improve performance and seems to in my limited
testing, reduce CPU utilization VERY slightly.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drop variables that had cache lines modified in simultaneous hot paths.
keep some variables modified on hot paths but make their storage per queue.
cache align DMA data buffer start addresses.
cache align (padding) some structures that end within a cacheline.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
decrease the memory utilization of the tx / rx queue allocation
by changing the default ring size to 512 (from 1024). At
1024 rx entries of 2KB each (from 4kB slab) with 16 queues
ixgbe was using 64 MB of memory per port, which is not
necessary.
Users can still change queue lengths with ethtool -k.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes the Tx queue selection for FCoE traffic from ixgbe_xmit_frame()
and does it in the ndo_select_queue() call, moving all Tx queue selection
into a single routine.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store the user priority for FCoE and use it directly for outgoing
FCoE traffic when DCB is enabled.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes skb_dma_map/unmap calls from the ixgbe driver due to the
fact that the calls don't work with HW IOMMU enabled systems. The problem
is that multiple mappings will give different results when HW IOMMU is
enabled and the skb_dma_map/unmap calls only have one location to store
mappings.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends the ethtool interface to display what PHY
is currently connected to a NIC. The results can be viewed in
ethtool ethX output.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes an issue when clearing out the RAR entries. If RAR[0]
is the only address in use, don't clear the others.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82598 shouldn't try and access LINKS2 while configuring
link and flow control. This is an 82599-only register.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow Control autoneg should be disabled for certain adapters
that don't support autonegotiation of Flow Control at 10 gigabit.
These interfaces are the 10GBASE-T devices, CX4, and SFP+, all
running at 10 gigabit only. 1 gigabit is fine.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was doing a divide by zero when adjusting tx-usecs.
This patch removes the divide by zero code and changes the logic slightly
to ignore tx-usecs in the case of shared TxRx vectors.
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There appears to be a stray setting of the VFE bit when registering vlans.
This should not be done as vlan filtering should be enabled any time the
interface is not in promiscous mode
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While configuring rscctl use rx buffer length from rx ring structure
instead of passing rx_buf_len to ixgbe_configure_rscctl
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Divide 82599 HWRSC counters into aggregated and flushed to count number of
packets getting coalesced per TCP connection.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tc is required by CONFIG_IXGBE_DCB.
This also fixes compilation warning:
drivers/net/ixgbe/ixgbe_main.c: In function ‘ixgbe_tx_is_paused’:
drivers/net/ixgbe/ixgbe_main.c:245: warning: unused variable ‘tc’
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not as fancy as coccinelle. Checkpatch errors ignored.
Compile tested allyesconfig x86, not all files compiled.
grep -rPl --include=*.[ch] "\brequest_irq\s*\([^,\)]+,\s*\&" drivers/net | while read file ; do \
perl -i -e 'local $/; while (<>) { s@(\brequest_irq\s*\([^,\)]+,\s*)\&@\1@g ; print ; }' $file ;\
done
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commmit 4b77b0a2ba EEH breaks
after the second error, since it calls pci_restore_state()
but it returns 0, since pci->state_saved is false.
So, this patch just call pci_save_state() after pci_restore_state().
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch pairs similar-numbered Rx and Tx queues onto a single
MSI-X vector. For example, Tx queue 0 and Rx queue 0's interrupt
with be ethX-RxTx-0. This allows for more efficient cleanup, since
fewer interrupts will be firing during device operation. It also
helps with a cleaner CPU affinity for IRQ affinity.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The values of r_idx and rx_ring are not used after the last time they
are set in ixgbe_msix_clean_rx(), so they can be removed.
Signed-off-by: Ali Gholami Rudi <ali@rudi.ir>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ioatdma was loaded we we were unable to transmit traffic. We weren't
using the correct registers in ixgbe_update_tx_dca for 82599 systems.
Likewise in ixgbe_configure_tx() we weren't disabling the arbiter before
modifying MTQC.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When DCB is enabled, the ixgbe_check_tx_hang() should check the corresponding
TC's TXOFF in TFCS based on the TC that the tx ring belongs to. Adds a
function to map from the tx_ring hw reg_idx to the correspodning TC and read
TFCS accordingly.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 32k gso_max_size when DCB is enabled is for 82598 only, not for 82599.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements the netdev_ops.ndo_fcoe_get_wwn in 82599 if it finds valid
prefix for the World Wide Node Name (WWNN) or World Wide Port Name (WWPN),
as well as valid SAN MAC address.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 82599 EEPROM supports alternative prefix for World Wide Node Name
(WWNN) and World Wide Port Name (WWPN). The prefixes can be used together
with the SAN MAC address to form the WWNN and WWPN, which can be used by
upper layer drivers such as Fiber Channel over Ethernet (FCoE).
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resolves a memory leak that occurs when you resize the rings via
the ethtool -G option while the interface is down.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 59aa3cc4 overlooked the way offsets for netdev stats were considered.
Because of this some of the stats shown by ethtool -S were wrong.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows the recently added backplane device IDs that support KR
to fail over to KX during link setup. This is accomplished by the new MAC
link setup function ixgbe_setup_mac_link_smartspeed(). Comments were also
updated to better document the reason for the delays chosen for KX, KX4, BX,
BX4 and KR connections.
Signed-off-by: Don Skidmore <don.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch will add the device ID for the 82599-based Ethernet
Express Module X520-P2 SFI card.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the private adapter structure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data center bridging ops structure can be const
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds device support for the 82599 based X520 10GbE
Dual Port KX4 Mezzanine card.
Signed-off-by: Don Skidmore<donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch will add support for the 82599 Dual port Backplane
device (0x10f8). This device has the ability to link in serial (KR) and
parallel (KX4/KX) modes, depending on what the switch capabilities are in
the blade chassis.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only error returned by pci_{en,dis}able_pcie_error_reporting() is
-EIO which simply means that Advanced Error Reporting is not supported.
There is no need to report that, so remove the error check from e1000e,
igb and ixgbe.
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ccffad25b5 changed parameters for function
ixgbe_update_uc_addr_list_generic but parameter description was not updated.
This patch corrects it.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ATR support for UDP on 82599 needs to be redesigned, since the
current model doesn't make much sense. The fallout from having
it in though is it causes all UDP traffic to still compute the
ATR hashes on transmit, which are useless. This removal will
return upwards of 10% of relative computational overhead in
forwarding tests.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When LRO is enabled, the received packet and byte counters represent the
LRO'd packets, not the packets/bytes on the wire. The Intel 82599 NIC has
registers that keep count of the physical packets. Add these counters to
the ethtool stats. The byte counters are 36-bit, but the high 4 bits were
being ignored in the 2.6.31 ixgbe driver: Read those as well to allow
longer time between polling the stats to detect wraps.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of changes have gone in since the last version bump. Bump
it to reflect the changes.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Backplane flow control autonegotiation is currently broken for
ixgbe devices. This patch fixes the flow control issues
with clause 37 autoneg.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82599 has a different register offset for the Tx DCA control registers.
We disable relaxed ordering of the descriptor writebacks for Tx head
writeback, but didn't disable it properly for 82599. However, this
shouldn't be a visible issue, since ixgbe doesn't use Tx head writeback.
This patch just makes sure we're not doing blind writes to offsets we
don't expect.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shorten ixgbe_configure_rx() and lessen indent depth.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the user to set Tx specific itr values. This only makes sense
when there are separate vectors for Tx and Rx. When the queues are
doubled up RxTx on the vectors, we still only use the rx itr value.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We weren't stoping the sfp_timer after the device was brought down.
This patch properly cleans up.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the media type detection for CX4 adapters lumps them into a
type of fiber. This causes some strange fallout when firmware verification
is done on the NIC, and certain fiber NIC rules get enforced incorrectly.
This patch introduces a new media type for CX4, and puts both 82598 and
82599 CX4 adapters into this bucket.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for CX4 adapters based on 82599.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packet split feature was recently moved out of the adapter-wide flags
feature field and into a per-Rx ring feature field. In the process, packet
split isn't properly disabled in the Rx ring if the adapter has it globally
disabled, followed by a device reset.
This won't impact the driver today, since it's always in packet split mode.
However, this will prevent any pitfalls if someone disables packet split on
the adapter in the future and doesn't disable it in each ring.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FCoE DDP in 82599 can be used for both FCoE initiator as well as FCoE
target, depending on the indication of the exchange being the responder or
originator in the F_CTL (frame control) field in the encapsulated Fiber
Channel frame header (T10 Spec., FC-FS). For the initiator, OX_ID is used
for FCoE DDP, where for the target RX_ID is used for FCoE DDP.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a simple selection of a FCoE tx queue based on the current cpu id to
distribute transmission of FCoE traffic evenly among multiple FCoE transmit
queues.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for multiple transmit queues to the Fiber Channel
over Ethernet (FCoE) feature found in 82599. Currently, FCoE has multiple
Rx queues available, along with a redirection table, that helps distribute
the I/O load across multiple CPUs based on the FC exchange ID. To make
this the most effective, we need to provide the same layout of transmit
queues to match receive.
Particularly, when Data Center Bridging (DCB) is enabled, the designated
traffic class for FCoE can have dedicated queues for just FCoE traffic,
while not affecting any other type of traffic flow.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 82599 multi speed fiber case when driver is loaded without any
cable and reconnecting the cable with a 1G partner does not bring
up the link in 1Gb mode. When there is no link we first setup the link
at 10G & 1G and then try to re-establish the link at highest speed 10G
and thereby changing autoneg_advertised value to highest speed 10G.
After connecting back the cable to a 1G link partner we never try 1G
as autoneg advertised value is changed to link at 10G only. The
following patch fixes the issue by properly initializing the
autoneg_advertised value just before exiting from link setup routine.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When disabling the Rx and Tx data arbiters prior to configuration changes,
the arbiters were not being shut down properly. This can create a race
in the DCB hardware blocks, and potentially hang the arbiters. Also, the
Tx descriptor arbiter shouldn't be disabled when applying configuration
changes; disabling this arbiter can cause a Tx hang.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link code cleanup: a number of redundant functions and MAC variables are cleaned up,
with some functions being consolidated into a single-purpose code path.
Removed following deprecated link functions and mac variables
* ixgbe_setup_copper_link_speed_82598
* ixgbe_setup_mac_link_speed_multispeed_fiber
* ixgbe_setup_mac_link_speed_82599
* mac.autoneg, mac.autoneg_succeeded, phy.autoneg_wait_to_complete
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for dcbnl_rtnl_ops.setapp/getapp to set or get the current user
priority bitmap for the given application protocol. Currently, 82599 only
supports setapp/getapp for Fiber Channel over Ethernet (FCoE) protocol.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support to the net_device_ops.ndo_fcoe_enable/disable for 82599. This
consequently allows us to dynamically turn FCoE offload feature on or off
upon incoming calls to ndo_fcoe_enable/disable. When this happens, FCoE offload
features are enabled/disabled accordingly, and this is regardless of whether
DCB being turned on or not.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of some bogus return wrapping as well.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were already exporting TSO6 to the vlan, but we weren't exporting the
checksum support for IPV6 which was causing warning messages to be
displayed when doing IPv6 TSO over a vlan.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have some ~40 functions that were being called out with 'make
namespacecheck'. This patch changes these functions to be static.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix ethtool get_settings logic to report 10G & 1G advertised and
supported link modes in all 8259x 10G backplane connection types
except for 82598EB BX network connection type.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable netdev feature flag bit NETIF_F_FCOE_MTU for 82599 devices and enable
jumbo frame correspondingly when NETIF_F_FCOE_MTU is set.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates netdev->vlan_features for NETIF_F_FCOE_CRC and NETIF_F_FSO, so that
FCoE CRC and GSO offloads will get used for FCoE over ixgbe based vlan
interface.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Traffic received with a priority tag (VID = 0) and non-zero priority value was
incorrectly handled by the VLAN packet code path due to a check on zero for
the whole VLAN tag instead of just the VID.
This patch masked out the priority field when checking the vlan tag for
received VLAN packets.
Signed-off-by: Lucy Liu <lucy.liu@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We return the ddp->len in ixgbe_fcoe_ddp() to indicate the length of data that
have been DDPed. However, it is possible that the length is 0, e.g., for SCSI
READ, the FCP_RSP may come back w/ SCSI status 0x28 as Task Set Full with no FCP
data for DDP. In ixgbe_fcoe_ddp(), we return 0 to indicate not passing DDPed
packets to upper layer. Therefore in the case of ddp->len being 0 upon FCP_RSP,
we do not want to return the 0 ddp->len as we want FCP_RSP to be always
delivered to the upper layer. This patch fixes this bug by setting rc only if
ddp->len is non-zero.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently setting rx-usecs when the interface is in legacy interrupt
mode it is not immediate. We were only setting EITR for each MSIx
vector and since this count would be zero for legacy mode it wasn't
set until after a reset. This patch corrects that by checking what
mode we are in and then setting EITR accordingly.
Signed-off-by: Don Skidmore <donald.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For 82599, packet split has to be disabled for FCoE direct data placement.
However, this is only required on received queues allocated for FCoE. This
patch adds a per ring flags to indicate if packet split is disabled on a
per queue basis, particularly for FCoE, as packet split must be disabled
for large receive using direct data placement (DDP).
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of passing the register index of the corresponding rx_ring and find
the way back to get to corresponding rx_ring in ixgbe_configure_srrctl(),
simplify the function ixgbe_configure_srrctl() by passing the rx_ring into
it. Then the register index for that rx_ring is already available from
rx_ring->reg_idx.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb priority to vlan-qos egress mapping that can be configured using
set_egress_map with vconfig is overriden by the DCB code in the driver.
This patch allows this existing mechanism to work and will increase the
configuration flexibility of DCB mode on Linux.
A hierarchy of configuration is:
1. Modifies the ixgbe_select_queue() routine for DCB mode to return the
priority value from the VLAN tag. It will normally be zero, unless the egress
priority map has modified it. This will get packets into the correct queue and
result in the queue_mapping field being set correctly.
2. Any tc filter which modifies queue_mapping will be honored, as the filters
are handled after the vlan egress map is handled.
Signed-off-by: Lucy Liu <lucy.liu@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default completion timeout values for 82598 should be in the
range of 50us to 50ms, however the hardware default for these
parts is 500us to 1ms which is less than the 10ms recommended by
the pcie spec. To address this we need to increase the value to
either 10ms to 250ms for capability version 1 configuration, or
16ms to 55ms for version 2.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a user disables interrupt throttling with ethtool on 82599 devices,
the interrupt timer may not be re-enabled if hardware RSC is running. The
RSC completions in hardware don't complete before the next ITR event tries
to fire, so the ITR timer never gets re-armed. This patch increases the
amount of time between interrupts when throttling is disabled (rx-usecs =
0) when the hardware RSC deature is enabled.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A second set of feature flag bits was added, and the hardware RSC engine
flags were moved there. However, the code itself didn't make the move
completely to use the new bitmap.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our ndo_poll_controller callback is broken for anything but non-multiqueue
setups. This fixes that issue.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an 82599 errata that UDP frames with a zero checksum are
incorrectly marked as checksum invalid by the hardware. This was
leading to misleading hw_csum_rx_error counts. This patch adds a
test around this counter increase for this condition.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calls to device_init_wakeup should not be necessary in drivers that use
device_set_wakeup_enable since pci_pm_init will set the can_wakeup flag
for the device when initialized.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain types of control packets (LLDP, LACP, etc.) are not supposed to have a
priority tag or vlan tag inserted. Ixgbe driver is currently priority
tagging everything (if packet is not on a VLAN interface).
This patch modifies DCB mode, so that packets marked with skb priority
TC_PRIO_CONTROL are not priority tagged. It also transmits these packets on
the highest priority traffic class.
Programs (like dcbd) can set the skb priority using a socket option. Or, a tc
filter can be configured to set the priority value. Using the value
TC_PRIO_CONTROL (7) has the benefit that it is already defined in the kernel,
and the bonding LACP code already sets the skb->priority field to this value.
Signed-off-by: Lucy Liu <lucy.liu@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, FCoE offload feature is turned on when the kernel config has
CONFIG_FCOE or CONFIG_FCOE_MODULE set. However, we really want to turn
FCoE offload on when there is FCoE traffic passing and turn it off when
it's just LAN traffic. Since FCoE depends on a lossless network provided
by DCB, this allows us to have FCoE turned on/off when user turns on DCB
using dcbtool.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep the version number marching along as updates come in.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for a new copper device for 82598, device id 0x150b.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the link comes up, the driver detects which flow control settings are
active. This is done using bitwise operations directly from the hardware
registers, and assumes the proper boolean assignment. Make this an
explicit boolean value before assignment to the bool.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool offline test is the only consumer of the legacy descriptors.
Update that path to only use advanced descriptors, and remove all support
for legacy descriptors.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove debug DPRINTK in DCB mode netlink interface.
Signed-off-by: Lucy Liu <lucy.liu@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change clears the address data block memory space, which is needed for
the 82598 which does not have a SAN MAC.
Signed-off-by: Lucy Liu <lucy.liu@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix coexistence of Fiber Channel over Ethernet (FCoE) and Flow Director (FDIR)
in 82599 and remove the disabling of FDIR when FCoE is enabled.
Currently, FDIR is turned off when FCoE is enabled under the assumption that
FCoE is always enabled with DCB being turned on. However, FDIR does not have
to be turned off all the time when FCoE is enabled since FCoE can be enabled
without DCB being turned on, e.g., use link pause only. This patch makes sure
that when DCB is turned on or off, FDIR is turned on or off correspondingly;
and when FCoE is enabled, it does not disable FDIR, rather, it will have FDIR
set up properly so FCoE and FDIR can coexist regardless of DCB being on or off.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wake-on-lan is currently only supported by 82599 KX4 devices, in all
other cases return a proper value from ixgbe_wol_exclusion function call.
Otherwise from ethtool we will be able to change wol options of
unsupported 8259x devices.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if we loaded the driver, insert an unsupported module, and then
attempt to "ifconfig up" the device it will be brought down but the netdev
would not be unregistered. This behavior is different than all other
code paths. This patch corrects that by down'ing the device and then
scheduling the sfp_config_module_task tasklet. The tasklet will detect
this condition (like it does with other code paths) and do the
unregister_netdev().
I also removed the log message as this condition (an unsupported SFP+
module) will be logged in sfp_config_module_task.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change to check the SFP+ module again on open() was
causing the XFP (non-SFP+) adapters to be rejected. We
only want to try and re-identify the SFP+ module if the
original probe found that this device was an SFP+ device.
So for this code path (driver loaded with SFP module, module
inserted, ifconfig up of the device) the type will be
ixgbe_phy_unknown for an unidentified SFP+ module. So we
only check if that is the case.
This problem also shows up on Copper devices.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several small fixes around negative test case of the insertion of a
IXGBE_ERR_NOT_SUPPORTED module.
- mdio45_probe call was always failing due to mdio.prtad not being
set. The function set to mdio.mdio_read was still working as we just
happen to always be at prtad == 0. This will allow us to set the phy_id
and phy.type correctly now.
- There was timing issue with i2c calls when initiated from a tasklet.
A small delay was added to allow the electrical oscillation to calm down.
- Logic change in ixgbe_sfp_task that allows NOT_SUPPORTED condition
to be recognized.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses three WARN_ON statements from DMA-API debug code
ixgbe is mapping more than it unmaps, reduce the length of the map call and
remove the "used once" local variable.
found by Joerg Roedel <joerg.roedel@amd.com> in 2.6.30, so is a candidate
for -stable.
in addition, fix missing ->dma = 0 after unmap to prevent double free with
pci_unmap_single
and lastly, don't unmap (half) pages that aren't mapped.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapter link advertisement capabilities were not persistent during
adapter resets. While configuring multispeed fiber link check for
phy autoneg_advertised settings before overwriting with default
link capabilities
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82599 single speed fiber modules only support 10G/Full. Return
proper device capabilities while querrying the adapter and error
while changing device advertisement/speed/duplex capabilities.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We had a wide range of log messages for the same sort of SFP
failure. This patch makes them all more similar and less
confusing along with converting them to dev_err.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're about to make DMA_nnBIT_MASK() emit `deprecated' warnings. Convert the
remaining stragglers which are visible to the x86_64 build.
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Eric Moore <Eric.Moore@lsil.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Yi Zou <yi.zou@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is inspired by patch recently posted by Johannes Berg. Basically what
my patch does is to group list and a count of addresses into newly introduced
structure netdev_hw_addr_list. This brings us two benefits:
1) struct net_device becames a bit nicer.
2) in the future there will be a possibility to operate with lists independently
on netdevices (with exporting right functions).
I wanted to introduce this patch before I'll post a multicast lists conversion.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
drivers/net/bnx2.c | 4 +-
drivers/net/e1000/e1000_main.c | 4 +-
drivers/net/ixgbe/ixgbe_main.c | 6 +-
drivers/net/mv643xx_eth.c | 2 +-
drivers/net/niu.c | 4 +-
drivers/net/virtio_net.c | 10 ++--
drivers/s390/net/qeth_l2_main.c | 2 +-
include/linux/netdevice.h | 17 +++--
net/core/dev.c | 130 ++++++++++++++++++--------------------
9 files changed, 89 insertions(+), 90 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Include offloaded FCoE data into total rx/tx statistics for 82599 so they
are properly reflected by ethtool or ifconfig.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_dma_unmap() is quite expensive for small packets,
because we use two different cache lines from skb_shared_info.
One to access nr_frags, one to access dma_maps[0]
Instead of dma_maps being an array of MAX_SKB_FRAGS + 1 elements,
let dma_head alone in a new dma_head field, close to nr_frags,
to reduce cache lines misses.
Tested on my dev machine (bnx2 & tg3 adapters), nice speedup !
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With all the last patchsets going in for 82599 feature enablement, the
driver version needs to be increased for better identification.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82599 has a FW running that helps manage the internal SFI PHY. There are
also a number of pre-production samples of these SFI-based devices in the
field. This patch adds a check to look for the firmware running on all
SFP+ based adapters, and displays a warning to the system log if a
pre-production adapter is identified. The driver will continue loading
though, with no functional degradation.
Also remove an old function prototype from ixgbe_82599.c that isn't being
used.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch rearranges the ixgbe_ring struct to make better use of
cacheline efficiency.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables Flow Director's ATR functionality to the main base
driver for 82599.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the functions for ixgbe to initialize Flow Director. It
also has the function APIs to add Flow Director filters from the base
driver. This also includes ATR, Application Targeted Routing, which is a
feature set of Flow Director. This is the hash-based mechanism to
automatically identify flows and add filters based on the hash, and direct
the Rx of that flow back to that same CPU.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow Director is a Rx filter mechanism designed to match Rx flows back to
the same CPU that the flow's Tx occurred from. This patch adds the first
piece, the defines for the hardware registers, to enable this feature in
82599 hardware.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a second feature flag variable to use for future feature
expansion. Add HW RSC to this new feature flags variable.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the tx cleanup processing out of the MSI-X interrupt
processing and gives it it's own napi routine. This allows the driver to
process TX cleanup in a polling context instead of in an interrupt context
which prevents TX from starving RX.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The v_idx value was being used as both a bitmask and an index. This change
makes it so that the q_vector contains the index and allows for much of the
code to be simplified since disabling a q_vector involves only clearing one
bit in the interrupt bitmask.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver so that it uses rx_buffer_info->dma to
determine if it needs to unmap the page instead of sh_info->nr_frags. This
helps to prevent a cache line miss when receiving small packets as the
rx_buffer_info data should already be in the cache.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool support to change advertised link modes/autoneg settings of
82599 multispeed fiber adapters.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix autoneg restart issues in flow control path which might create
endless link flickering due to known timing issues with 82599
adapters.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakakla@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82599 supports multispeed fiber optical modules (10Gbps/1Gbps). Some
scenarios can cause the autotry mechanism to not negotiate link properly.
What needs to happen is the driver must flap the Tx laser to induce an Rx
Loss of Signal on the link partner. This will restart the autotry
mechanism to get link into a known state. The software definable pin (SDP)
3 on the 0x10fb NIC is wired to cause a Tx LOS event, which triggers the
Rx LOS we require.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the ethtool internal test engine.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When reprogramming the 82599 analog PHY to either SFI optical or Direct
Attach Twinax, we need to restart the DSP in the PHY. The current method
can cause contention with our FW which is managing PHY state, and will
cause unexpected link flaps. This patch fixes the DSP restart by issuing
an AN_RESTART in the MAC, which will properly propagate the DSP restart to
the PHY. This ensures we don't collide with the FW.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 82599 KX4 device defaults to legacy power management, or APME. This
puts the device into ACPI mode, which allows more robust WoL setups to
work properly.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts unicast address list to standard list_head using
previously introduced struct netdev_hw_addr. It also relaxes the
locking. Original spinlock (still used for multicast addresses) is not
needed and is no longer used for a protection of this list. All
reading and writing takes place under rtnl (with no changes).
I also removed a possibility to specify the length of the address
while adding or deleting unicast address. It's always dev->addr_len.
The convertion touched especially e1000 and ixgbe codes when the
change is not so trivial.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
drivers/net/bnx2.c | 13 +--
drivers/net/e1000/e1000_main.c | 24 +++--
drivers/net/ixgbe/ixgbe_common.c | 14 ++--
drivers/net/ixgbe/ixgbe_common.h | 4 +-
drivers/net/ixgbe/ixgbe_main.c | 6 +-
drivers/net/ixgbe/ixgbe_type.h | 4 +-
drivers/net/macvlan.c | 11 +-
drivers/net/mv643xx_eth.c | 11 +-
drivers/net/niu.c | 7 +-
drivers/net/virtio_net.c | 7 +-
drivers/s390/net/qeth_l2_main.c | 6 +-
drivers/scsi/fcoe/fcoe.c | 16 ++--
include/linux/netdevice.h | 18 ++--
net/8021q/vlan.c | 4 +-
net/8021q/vlan_dev.c | 10 +-
net/core/dev.c | 195 +++++++++++++++++++++++++++-----------
net/dsa/slave.c | 10 +-
net/packet/af_packet.c | 4 +-
18 files changed, 227 insertions(+), 137 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Followup of commits 9d21493b4b
and 08baf56108
(net: tx scalability works : trans_start)
(net: txq_trans_update() helper)
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Multi queue drivers can
avoid one cache miss (on dev->trans_start) in their start_xmit()
handler.
Exceptions are NETIF_F_LLTX drivers (vxge & tehuti)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a build warning due to an unused label.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we loaded the driver with out a SFP module plugged in it would
leave it in a state that make it later unable to link when a module
was plugged in. This patch corrects that by:
ixgbe_probe() - moving the check for IXGBE_ERR_SFP_NOT_PRESENT from
after get_invariants() to after reset_hw() as now reset_hw() is
where this condition will be indentified.
ixgbe_reset_hw_82598() - Enable this function to now return
IXGBE_ERR_SFP_NOT_PRESENT.
ixgbe_identify_sfp_module_generic() - This where the lack of SFP
module is detected. Modifications are added to allow a different
return value for modules that just haven't been plugged in yet.
Other functions were updated to allow correct logging.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device ID 0x10d8 is the default silicon device ID for 82599. However, the
device will not be functional without an EEPROM, so we want to prevent the
driver from loading on the device. Otherwise, the driver will load, but no
PHY setup or PCIe setup will occur, causing the device to be unusable. To
prevent users from encountering this, just remove the device ID.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
