After we call find_data_page in truncate_partial_data_page, we could not
guarantee this page is updated or not as error may occurred in lower layer.
We'd better check status of the page to avoid this no updated page be
writebacked to device.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
We have already set page update in ->write_begin, so we should remove redundant
SetPageUptodate in ->write_end.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=75861
Denis 2014-05-10 11:28:59 UTC reported:
"F2FS-fs (mmcblk0p28): mounting..
Unable to handle kernel NULL pointer dereference at virtual address 00000018
...
[<c0a2f678>] (_raw_spin_lock+0x3c/0x70) from [<c03a0330>] (issue_flush_thread+0x50/0x17c)
[<c03a0330>] (issue_flush_thread+0x50/0x17c) from [<c01b4064>] (kthread+0x98/0xa4)
[<c01b4064>] (kthread+0x98/0xa4) from [<c0108060>] (kernel_thread_exit+0x0/0x8)"
This patch assign cmd_control_info in sm_info before issue_flush_thread is being
created, so this make sure that issue flush thread will have no chance to access
invalid info in fcc.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Reviewed-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
If we don't check the current backing device status, balance_dirty_pages can
fall into infinite pausing routine.
This can be occurred when a lot of directories make a small number of dirty
dentry pages including files.
Reported-by: Brian Chadwick <brianchad@westnet.com.au>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
If an inode is renamed, it should be registered as file_lost_pino to conduct
checkpoint at f2fs_sync_file.
Otherwise, the inode cannot be recovered due to no dent_mark in the following
scenario.
Note that, this scenario is from xfstests/322.
1. create "a"
2. fsync "a"
3. rename "a" to "b"
4. fsync "b"
5. Sudden power-cut
After recovery is done, "b" should be seen.
However, the result shows "a", since the recovery procedure does not enter
recover_dentry due to no dent_mark.
The reason is like below.
- The nid of "a" is checkpointed during #2, f2fs_sync_file.
- The inode page for "b" produced by #3 is written without dent_mark by
sync_node_pages.
So, this patch fixes this bug by assinging file_lost_pino to the "a"'s inode.
If the pino is lost, f2fs_sync_file conducts checkpoint, and then recovers
the latest pino and its dentry information for further recovery.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch correct releasing code of new_page to avoid BUG_ON in error patch of
f2fs_rename.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
If we fail in this path:
->init_inode_metadata
->make_empty_dir
->get_new_data_page
->grab_cache_page return -ENOMEM
We will bug on in error path of init_inode_metadata when call remove_inode_page
because i_block = 2 (one inode block will be released later & one dentry block).
We should release the dentry block in init_inode_metadata to avoid this BUG_ON,
and avoid leak of dentry block resource, because we never have second chance to
release that block in ->evict_inode as in upper error path we make this inode
'bad'.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch add lower bound verification for nid in check_nid_range, so nids
reserved like 0, node, meta passed by caller could be checked there.
And then check_nid_range could be used in f2fs_nfs_get_inode for simplifying
code.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch fixes the fallocate bug like below. (See xfstests/255)
In fallocate(fd, 0, 20480),
expand_inode_data processes
for (index = pg_start; index <= pg_end; index++) {
f2fs_reserve_block();
...
}
So, even though fallocate requests 20480, 5 blocks, f2fs allocates 6 blocks
including pg_end.
So, this patch adds one condition to avoid block allocation.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Previous get_block in f2fs didn't report the newly allocated region which has
NEW_ADDR.
For reader, it should not report, but fiemap needs this.
So, this patch introduces two get_block sharing core function.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Pull vfs updates from Al Viro:
"This the bunch that sat in -next + lock_parent() fix. This is the
minimal set; there's more pending stuff.
In particular, I really hope to get acct.c fixes merged this cycle -
we need that to deal sanely with delayed-mntput stuff. In the next
pile, hopefully - that series is fairly short and localized
(kernel/acct.c, fs/super.c and fs/namespace.c). In this pile: more
iov_iter work. Most of prereqs for ->splice_write with sane locking
order are there and Kent's dio rewrite would also fit nicely on top of
this pile"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (70 commits)
lock_parent: don't step on stale ->d_parent of all-but-freed one
kill generic_file_splice_write()
ceph: switch to iter_file_splice_write()
shmem: switch to iter_file_splice_write()
nfs: switch to iter_splice_write_file()
fs/splice.c: remove unneeded exports
ocfs2: switch to iter_file_splice_write()
->splice_write() via ->write_iter()
bio_vec-backed iov_iter
optimize copy_page_{to,from}_iter()
bury generic_file_aio_{read,write}
lustre: get rid of messing with iovecs
ceph: switch to ->write_iter()
ceph_sync_direct_write: stop poking into iov_iter guts
ceph_sync_read: stop poking into iov_iter guts
new helper: copy_page_from_iter()
fuse: switch to ->write_iter()
btrfs: switch to ->write_iter()
ocfs2: switch to ->write_iter()
xfs: switch to ->write_iter()
...
iter_file_splice_write() - a ->splice_write() instance that gathers the
pipe buffers, builds a bio_vec-based iov_iter covering those and feeds
it to ->write_iter(). A bunch of simple cases coverted to that...
[AV: fixed the braino spotted by Cyrill]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This patch-set includes the following major enhancement patches.
o enhance wait_on_page_writeback
o support SEEK_DATA and SEEK_HOLE
o enhance readahead flows
o enhance IO flushes
o support fiemap
o add some tracepoints
The other bug fixes are as follows.
o fix to support a large volume > 2TB correctly
o recovery bug fix wrt fallocated space
o fix recursive lock on xattr operations
o fix some cases on the remount flow
And, there are a bunch of cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xqsO
-----END PGP SIGNATURE-----
Merge tag 'for-f2fs-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs updates from Jaegeuk Kim:
"In this round, there is no special interesting feature, but we've
investigated a couple of tuning points with respect to the I/O flow.
Several major bug fixes and a bunch of clean-ups also have been made.
This patch-set includes the following major enhancement patches:
- enhance wait_on_page_writeback
- support SEEK_DATA and SEEK_HOLE
- enhance readahead flows
- enhance IO flushes
- support fiemap
- add some tracepoints
The other bug fixes are as follows:
- fix to support a large volume > 2TB correctly
- recovery bug fix wrt fallocated space
- fix recursive lock on xattr operations
- fix some cases on the remount flow
And, there are a bunch of cleanups"
* tag 'for-f2fs-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (52 commits)
f2fs: support f2fs_fiemap
f2fs: avoid not to call remove_dirty_inode
f2fs: recover fallocated space
f2fs: fix to recover data written by dio
f2fs: large volume support
f2fs: avoid crash when trace f2fs_submit_page_mbio event in ra_sum_pages
f2fs: avoid overflow when large directory feathure is enabled
f2fs: fix recursive lock by f2fs_setxattr
MAINTAINERS: add a co-maintainer from samsung for F2FS
MAINTAINERS: change the email address for f2fs
f2fs: use inode_init_owner() to simplify codes
f2fs: avoid to use slab memory in f2fs_issue_flush for efficiency
f2fs: add a tracepoint for f2fs_read_data_page
f2fs: add a tracepoint for f2fs_write_{meta,node,data}_pages
f2fs: add a tracepoint for f2fs_write_{meta,node,data}_page
f2fs: add a tracepoint for f2fs_write_end
f2fs: add a tracepoint for f2fs_write_begin
f2fs: fix checkpatch warning
f2fs: deactivate inode page if the inode is evicted
f2fs: decrease the lock granularity during write_begin
...
There is an errorneous case during the recovery like below.
In recovery_dentry,
1) dir = f2fs_iget();
2) mark the dir with FI_DELAY_IPUT
3) goto unmap_out
After the end of recovery routine, there is no dirty dentries so the dir cannot
be released by iput in remove_dirty_dir_inode.
This patch fixes such the bug case by handling the iget and iput in the
recovery_dentry procedure.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
aops->write_begin may allocate a new page and make it visible only to have
mark_page_accessed called almost immediately after. Once the page is
visible the atomic operations are necessary which is noticable overhead
when writing to an in-memory filesystem like tmpfs but should also be
noticable with fast storage. The objective of the patch is to initialse
the accessed information with non-atomic operations before the page is
visible.
The bulk of filesystems directly or indirectly use
grab_cache_page_write_begin or find_or_create_page for the initial
allocation of a page cache page. This patch adds an init_page_accessed()
helper which behaves like the first call to mark_page_accessed() but may
called before the page is visible and can be done non-atomically.
The primary APIs of concern in this care are the following and are used
by most filesystems.
find_get_page
find_lock_page
find_or_create_page
grab_cache_page_nowait
grab_cache_page_write_begin
All of them are very similar in detail to the patch creates a core helper
pagecache_get_page() which takes a flags parameter that affects its
behavior such as whether the page should be marked accessed or not. Then
old API is preserved but is basically a thin wrapper around this core
function.
Each of the filesystems are then updated to avoid calling
mark_page_accessed when it is known that the VM interfaces have already
done the job. There is a slight snag in that the timing of the
mark_page_accessed() has now changed so in rare cases it's possible a page
gets to the end of the LRU as PageReferenced where as previously it might
have been repromoted. This is expected to be rare but it's worth the
filesystem people thinking about it in case they see a problem with the
timing change. It is also the case that some filesystems may be marking
pages accessed that previously did not but it makes sense that filesystems
have consistent behaviour in this regard.
The test case used to evaulate this is a simple dd of a large file done
multiple times with the file deleted on each iterations. The size of the
file is 1/10th physical memory to avoid dirty page balancing. In the
async case it will be possible that the workload completes without even
hitting the disk and will have variable results but highlight the impact
of mark_page_accessed for async IO. The sync results are expected to be
more stable. The exception is tmpfs where the normal case is for the "IO"
to not hit the disk.
The test machine was single socket and UMA to avoid any scheduling or NUMA
artifacts. Throughput and wall times are presented for sync IO, only wall
times are shown for async as the granularity reported by dd and the
variability is unsuitable for comparison. As async results were variable
do to writback timings, I'm only reporting the maximum figures. The sync
results were stable enough to make the mean and stddev uninteresting.
The performance results are reported based on a run with no profiling.
Profile data is based on a separate run with oprofile running.
async dd
3.15.0-rc3 3.15.0-rc3
vanilla accessed-v2
ext3 Max elapsed 13.9900 ( 0.00%) 11.5900 ( 17.16%)
tmpfs Max elapsed 0.5100 ( 0.00%) 0.4900 ( 3.92%)
btrfs Max elapsed 12.8100 ( 0.00%) 12.7800 ( 0.23%)
ext4 Max elapsed 18.6000 ( 0.00%) 13.3400 ( 28.28%)
xfs Max elapsed 12.5600 ( 0.00%) 2.0900 ( 83.36%)
The XFS figure is a bit strange as it managed to avoid a worst case by
sheer luck but the average figures looked reasonable.
samples percentage
ext3 86107 0.9783 vmlinux-3.15.0-rc4-vanilla mark_page_accessed
ext3 23833 0.2710 vmlinux-3.15.0-rc4-accessed-v3r25 mark_page_accessed
ext3 5036 0.0573 vmlinux-3.15.0-rc4-accessed-v3r25 init_page_accessed
ext4 64566 0.8961 vmlinux-3.15.0-rc4-vanilla mark_page_accessed
ext4 5322 0.0713 vmlinux-3.15.0-rc4-accessed-v3r25 mark_page_accessed
ext4 2869 0.0384 vmlinux-3.15.0-rc4-accessed-v3r25 init_page_accessed
xfs 62126 1.7675 vmlinux-3.15.0-rc4-vanilla mark_page_accessed
xfs 1904 0.0554 vmlinux-3.15.0-rc4-accessed-v3r25 init_page_accessed
xfs 103 0.0030 vmlinux-3.15.0-rc4-accessed-v3r25 mark_page_accessed
btrfs 10655 0.1338 vmlinux-3.15.0-rc4-vanilla mark_page_accessed
btrfs 2020 0.0273 vmlinux-3.15.0-rc4-accessed-v3r25 init_page_accessed
btrfs 587 0.0079 vmlinux-3.15.0-rc4-accessed-v3r25 mark_page_accessed
tmpfs 59562 3.2628 vmlinux-3.15.0-rc4-vanilla mark_page_accessed
tmpfs 1210 0.0696 vmlinux-3.15.0-rc4-accessed-v3r25 init_page_accessed
tmpfs 94 0.0054 vmlinux-3.15.0-rc4-accessed-v3r25 mark_page_accessed
[akpm@linux-foundation.org: don't run init_page_accessed() against an uninitialised pointer]
Signed-off-by: Mel Gorman <mgorman@suse.de>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Jan Kara <jack@suse.cz>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Tested-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If data are overwritten through dio, previous f2fs doesn't remain the fsync mark
due to no additional node writes.
Note that this patch should resolve the xfstests:311.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
f2fs's cp has one page which consists of struct f2fs_checkpoint and
version bitmap of sit and nat. To support lots of segments, we need more
blocks for sit bitmap. So let's arrange sit bitmap as following:
+-----------------+------------+
| f2fs_checkpoint | sit bitmap |
| + nat bitmap | |
+-----------------+------------+
0 4k N blocks
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
[Jaegeuk Kim: simple code change for readability]
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Previously we allocate pages with no mapping in ra_sum_pages(), so we may
encounter a crash in event trace of f2fs_submit_page_mbio where we access
mapping data of the page.
We'd better allocate pages in bd_inode mapping and invalidate these pages after
we restore data from pages. It could avoid crash in above scenario.
Changes from V1
o remove redundant code in ra_sum_pages() suggested by Jaegeuk Kim.
Call Trace:
[<f1031630>] ? ftrace_raw_event_f2fs_write_checkpoint+0x80/0x80 [f2fs]
[<f10377bb>] f2fs_submit_page_mbio+0x1cb/0x200 [f2fs]
[<f103c5da>] restore_node_summary+0x13a/0x280 [f2fs]
[<f103e22d>] build_curseg+0x2bd/0x620 [f2fs]
[<f104043b>] build_segment_manager+0x1cb/0x920 [f2fs]
[<f1032c85>] f2fs_fill_super+0x535/0x8e0 [f2fs]
[<c115b66a>] mount_bdev+0x16a/0x1a0
[<f102f63f>] f2fs_mount+0x1f/0x30 [f2fs]
[<c115c096>] mount_fs+0x36/0x170
[<c1173635>] vfs_kern_mount+0x55/0xe0
[<c1175388>] do_mount+0x1e8/0x900
[<c1175d72>] SyS_mount+0x82/0xc0
[<c16059cc>] sysenter_do_call+0x12/0x22
Suggested-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
When large directory feathure is enable, We have one case which could cause
overflow in dir_buckets() as following:
special case: level + dir_level >= 32 and level < MAX_DIR_HASH_DEPTH / 2.
Here we define MAX_DIR_BUCKETS to limit the return value when the condition
could trigger potential overflow.
Changes from V1
o modify description of calculation in f2fs.txt suggested by Changman Lee.
Suggested-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch should resolve the following recursive lock.
[<ffffffff8135a9c3>] call_rwsem_down_write_failed+0x13/0x20
[<ffffffffa01749dc>] f2fs_setxattr+0x5c/0xa0 [f2fs]
[<ffffffffa0174c99>] __f2fs_set_acl+0x1b9/0x340 [f2fs]
[<ffffffffa017515a>] f2fs_init_acl+0x4a/0xcb [f2fs]
[<ffffffffa0159abe>] __f2fs_add_link+0x26e/0x780 [f2fs]
[<ffffffffa015d4d8>] f2fs_mkdir+0xb8/0x150 [f2fs]
[<ffffffff811cebd7>] vfs_mkdir+0xb7/0x160
[<ffffffff811cf89b>] SyS_mkdir+0xab/0xe0
[<ffffffff817244bf>] tracesys+0xe1/0xe6
[<ffffffffffffffff>] 0xffffffffffffffff
The call path indicates:
- f2fs_add_link
: down_write(&fi->i_sem);
- init_inode_metadata
- f2fs_init_acl
- __f2fs_set_acl
- f2fs_setxattr
: down_write(&fi->i_sem);
Here we should not call f2fs_setxattr, but __f2fs_setxattr.
But __f2fs_setxattr is a static function in xattr.c, so that I found the other
generic approach to use f2fs_setxattr.
In f2fs_setxattr, the page pointer is only given from init_inode_metadata.
So, this patch adds this condition to avoid this in f2fs_setxattr.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch uses exported inode_init_owner() to simplify codes in
f2fs_new_inode().
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
If we use slab memory in f2fs_issue_flush(), we will face memory pressure and
latency time caused by racing of kmem_cache_{alloc,free}.
Let's alloc memory in stack instead of slab.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch adds a tracepoint for f2fs_read_data_page to trace when page is
readed by user.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch adds a tracepoint for f2fs_write_{meta,node,data}_pages to trace when
pages are fsyncing/flushing.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch adds a tracepoint for f2fs_write_{meta,node,data}_page to trace when
page is writting out.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch adds a tracepoint for f2fs_write_end to trace write op of user.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch adds a tracepoint for f2fs_write_begin to trace write op of user.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
fix the following checkpatch warning:
WARNING: do {} while (0) macros should not be semicolon terminated
Signed-off-by: Zhang Zhen <zhenzhang.zhang@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
If the inode page is clean during its inode eviction, it'd better drop the page
to reduce further memory pressure.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch reduces the lock granularity during write_begin.
When the system is under memory pressure, it would be better to reduce
the locking time for the data pages.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
We don't need to wait on page writeback for these cases.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch splits grab_cache_page_write_begin into grab_cache_page and
wait_on_page_writeback for node pages.
This patch intends to enhance the latency to get node pages by alleviating
unnecessary wait_on_page_writeback.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Previous we do not truncate inline data in inode page when setattr, so following
case could still read the inline data which has already truncated:
1.write inline data
2.ftruncate size to 0
3.ftruncate size to max inline data size
4.read from offset 0
This patch introduces truncate_inline_data() to fix this problem.
change log from v1:
o fix a bug and do not truncate first page data after truncate inline data.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
We have no so such readahead mechanism in ->iterate() path as the one in
->read() path, it cause low performance when we read large directory.
This patch add readahead in f2fs_readdir() for better performance.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
We should set the error number correctly when we fail in recover_dentry(), so
the recover flow could stop for the reason as error number shows instead of
continuing.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
If an amount of data are allocated though fallocate and user writes a couple of
data among the space, f2fs should return the data offset made by user when
SEEK_DATA is requested.
For example, (N: NEW_ADDR by fallocate, X: NEW_ADDR by user)
1) fallocate 0 ~ 10MB
f -> N N N N N N N N N N N N ... N
2) write 4KB at 5MB offset
f -> N N N N N X N N N N N N ... N
3) SEEK_DATA from 0 should return 5MB offset
So, this patch adds a routine to search the first dirty page to handle that.
Then, the SEEK_DATA flow skips NEW_ADDR offsets until any dirty page is found.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
When SEEK_HOLE is requeted, it should return i_size if the hole position is
found outside of i_size.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
In This patch we introduce f2fs_seek_block to support SEEK_{DATA,HOLE} of
lseek(2).
change log from v1:
o fix bug when lseek from middle of page and fix wrong calculation of
PGOFS_OF_NEXT_DNODE macro.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Introduce help function {create,destroy}_flush_cmd_control to clean up
the create/destory flush merge operation.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Split the flush_merge fields from sm_i, and use the new struct flush_cmd_control
to wrap it, so that we can igonre these fileds if flush_merge is disable, and
it alse can the structs more neat.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Introduce help macro ADDRS_PER_PAGE() to get the number of address pointers in
direct node or inode.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
If f2fs_write_data_page is called through the reclaim path, we should submit
the bio right away.
This patch resolves the following issue that Marc Dietrich reported.
"It took me a while to bisect a problem which causes my ARM (tegra2) netbook to
frequently stall for 5-10 seconds when I enable EXA acceleration (opentegra
experimental ddx)."
And this patch fixes that.
Reported-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch passes the "flags" field to the low level setxattr functions
to use XATTR_REPLACE in the following patches.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
