A recent pull from wireless testing generates the following warning:
CC [M] drivers/net/wireless/b43/main.o
drivers/net/wireless/b43/main.c: In function ‘b43_op_set_key’:
drivers/net/wireless/b43/main.c:3636: warning: pointer type mismatch
in conditional expression
This fix was suggested by Johannes Berg <johannes@sipsolutions.net>.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Silence sparse by using a defined value PCI_D3hot instead of a magic
constant in a pci_set_power_state() call.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Couple of '_ATTR's were missing and SEC_CHAN_OFFSET to CHANNEL_TYPE
rename was missed in couple of places.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At least one ar5211 card (GIGABYTE GN-WLMA101, 168c:0012 subsystem
1458:e800) reports itself as 11g capable which seems to be a bug in the
eeprom. initvals.c assumes that ar5211 is only 11b capable and thus refuses
to initialize this card. Hence this patch changes the probing for 11g
capabilities to discard 11g capabilities for ar5211 cards which allows this
specific card to work fine in 11b and 11a modes.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Usually every prism54 design hardware has a tiny eeprom chip in which all
device specific data for calibration and link-tuning is stored.
The stlc45xx chips are the only exception.
They are made for embedded devices, where space is scarce.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for longbow RF chip.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support to upload pre-calculated calibration data to the firmware.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Under memory pressure, we may not be able to allocate a new skb for
new packets. If the allocation fails, ath5k_tasklet_rx will exit but
will leave a buffer in the list with a NULL skb, eventually triggering
a BUG_ON.
Extract the skb allocation from ath5k_rxbuf_setup() and change the
tasklet to allocate the next skb before accepting a packet.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch temporarily fixes a regression introduced by BT coexistence support.
There is an instability in connection when BT coexistence is enabled on some h/w.
This interim fix introduces a module parameter for BT coexistence configuration.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a check for LED_MODE_DEFAULT so that we use the link LED for rt2400
and rt2500 devices.
Signed-off-by: Andrew Price <andy@andrewprice.me.uk>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the IEEE80211_RADIOTAP_RATE flag was moved to be conditional, it
was mistakenly left without cpu_to_le32(). Fix that.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function is only used within rx.c, so mark it static.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add initial support for libertas devices using a GSPI interface. This has
been tested with the 8686.
GSPI is intended to be used on embedded systems. Board-specific parameters are
required (see libertas_spi.h).
Thanks to everyone who took a look at the earlier versions of the patch.
Signed-off-by: Colin McCabe <colin@cozybit.com>
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 reserves 24 bytes in skb->cb for the driver.
So far, we only used them to keep track of used and free device memory.
But p54spi will need a slice of it, as well as the stuck frame detection.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Old firmwares had no problems processing frames which filled eighth of the memory window.
However we have to be a bit more careful with fat frames when we talk to new firmwares.
Apart from that, I confess the old logic was a bit weird and not very sophisticated.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For any callbacks in ieee80211_ops, specify what values the return
codes represent. While at it, fix a couple of capitalization and
punctuation differences.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Reviewed-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
new kew -> a new key
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add GSPI constants to libertas core.
Fix misleading comment in lbs_setup_firmware.
Signed-off-by: Colin McCabe <colin@cozybit.com>
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl3945_init_drv() initialises the wrong lock, and sets the wrong power saving
default level.
With this power saving mode, we are losing a lot of frames in Ad-Hoc mode.
This is a bug fix for bug #1873.
( http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1873 )
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch uses power constraint level while determining the maximum
transmit power, there by it makes sure that any power mitigation
requirement for the channel in the current regulatory domain is met.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that we're using iwl_mod_params, we want our module parameters names to be
in sync with the structure.
So, to set iwl_mod_params.sw_crypto, we'd better use a "swcrypto" parameter
name instead of the "hwcrypto" current one.
Moreover, by setting the decrypted flag properly, this patch also fixes the HW
crypto path for 3945 (the current code is not setting it when running HW
crypto).
This is a bug fix for bug #1872
( http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1872 )
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes 3945 use of hw_params.rx_buf_size instead of
IWL_RX_BUF_SIZE. It also renames IWL_RX_BUF_SIZE to IWL_RX_BUF_SIZE_3K
and moves rx buffer defines into iwl-fh.h.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes doubly defined struct iwl3945_tfd_frame_data
and struct iwl3945_tfd_frame.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces iwl3945_x2_queue_used with iwl_queue_used.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces iwl3945_rx_queue_space with iwl_rx_queue_space.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch kills iwl3945_rx_queue_restock function on prise of new
hw_params.rx_wrt_ptr_reg which holds per NIC RX write pointer register.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes tx_ant_num for hw_params structure. It is not used.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211_hwsim has no problems with MFP, so report it as MFP capable.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure hardware CCMP for management frame protection and use
software crypto when needed.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Return -EOPNOTSUPP if the algorithm is not supported and -ENOSPC if
there is no room in the key cache. This avoids KERN_ERR printk in
mac80211 for "errors" that are actually expected to happen in normal
operating conditions.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows user space to determine whether a driver supports MFP and
behave properly without having to ask user to configure this in
MFP-optional mode.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If driver/firmware/hardware does not support CCMP for management
frames, it can now request mac80211 to take care of encrypting and
decrypting management frames (when MFP is enabled) in software. The
will need to add this new IEEE80211_KEY_FLAG_SW_MGMT flag when a CCMP
key is being configured for TX side and return the undecrypted frames
on RX side without RX_FLAG_DECRYPTED flag to use software CCMP for
management frames (but hardware for data frames).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When MFP is enabled, the AP does not allow a STA to associate if an
existing security association exists without first going through SA
Query process. When this happens, the association request is denied
with a new status code ("temporarily rejected") ans Association
Comeback IE is used to notify when the association may be tried again
(i.e., when the SA Query procedure has timed out).
Use the comeback time to update the mac80211 client MLME timer for
next association attempt to minimize waiting time if association is
temporarily rejected.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ieee80211_drop_unencrypted() to decide whether a received frame
should be dropped with management frames, too. If MFP is negotiated,
unprotected robust management frames will be dropped.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When sending out Action frames, allow ieee80211_tx_skb() to send them
without enforcing do_not_encrypt. These frames will be encrypted if
MFP has been negotiated.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Process SA Query Requests for client mode in mac80211. AP side
processing of SA Query Response frames is in user space (hostapd).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new WEXT IW_AUTH_* parameter for setting MFP
disabled/optional/required.
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added new SIOCSIWENCODEEXT algorithm for configuring BIP (AES-CMAC)
keys (IGTK).
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new IW_AUTH parameter for setting cipher suite for
multicast/broadcast management frames. This is for full-mac drivers
that take care of RSN IE generation for (re)association request frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add mechanism for managing BIP keys (IGTK) and integrate BIP into the
TX/RX paths.
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement Broadcast/Multicast Integrity Protocol for management frame
protection. This patch adds the needed definitions for the new
information element (MMIE) and implementation for the new "encryption"
type (though, BIP is actually not encrypting data, it provides only
integrity protection). These routines will be used by a follow-on patch
that enables BIP for multicast/broadcast robust management frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend CCMP to support encryption and decryption of unicast management
frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add flags for setting STA entries and struct ieee80211_if_sta to
indicate whether management frame protection (MFP) is used.
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We add support for multiple drivers to provide a regulatory_hint()
on a system by adding a wiphy specific regulatory domain cache.
This allows drivers to keep around cache their own regulatory domain
structure queried from CRDA.
We handle conflicts by intersecting multiple regulatory domains,
each driver will stick to its own regulatory domain though unless
a country IE has been received and processed.
If the user already requested a regulatory domain and a driver
requests the same regulatory domain then simply copy to the
driver's regd the same regulatory domain and do not call
CRDA, do not collect $200.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We are calling the reg_notifier() callback per band, this is
not necessary, just call it once.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This modifies hardware flags for powersave to support three different
flags:
* IEEE80211_HW_SUPPORTS_PS - indicates general PS support
* IEEE80211_HW_PS_NULLFUNC_STACK - indicates nullfunc sending in software
* IEEE80211_HW_SUPPORTS_DYNAMIC_PS - indicates dynamic PS on the device
It also adds documentation for all this which explains how to set the
various flags.
Additionally, it fixes a few things:
* a spot where && was used to test flags
* enable CONF_PS only when associated again
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
