Needed to support mpc52xx boards in arch/powerpc. This patch
retains the platform_bus support when compiling for arch/ppc,
but uses the of_platform bindings for arch/powerpc.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Single typo fix and whitespace changes. In preparation for heavy
changes to this driver when support for arch/powerpc is added.
Since the driver will be changing significantly anyway, then may
as well take the opportunity to clean it up first.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 32-bit version and 64-bit version are almost equal. Unify them. This
makes further improvements (for example, copying with parallel, supporting
PREFETCH, etc.) easier.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is a fix for a typo repeated several times in #error directives for
invalid SiByte configurations.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For the definition of atomic64_t atomic.h was relying on <asm/types.h>
having been included previously. Before changeset
d89d8e0637a5e4e0a12e90c4bc934d0d4c335239 this was happening as a
side effect of including <linux/spinlock.h>.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: (82 commits)
[PATCH] pata_ali: small fixes
[PATCH] pata_via: VIA 8251 bridged systems are now out and about
[PATCH] trivial piix: swap bogus dot for comma space
[PATCH] sata_promise: PHYMODE4 fixup
[PATCH] libata: always use polling IDENTIFY
[libata] pata_cs5535: fix build
[PATCH] ahci: do not powerdown during initialization
[PATCH] libata: prepare ata_sg_clean() for invocation from EH
[PATCH] libata: separate out rw ATA taskfile building into ata_build_rw_tf()
[PATCH] libata: implement ata_exec_internal_sg()
[PATCH] libata: make sure IRQ is cleared after ata_bmdma_freeze()
[PATCH] libata: move BMDMA host status recording from EH to interrupt handler
[PATCH] libata: make sure sdev doesn't go away while rescanning
[PATCH] libata: don't request sense if the port is frozen
[PATCH] libata: fix READ CAPACITY simulation
[PATCH] libata: implement ATA_FLAG_SETXFER_POLLING and use it in pata_via, take #2
[PATCH] libata: set IRQF_SHARED for legacy PCI IDE IRQs
[PATCH] libata: remove unused HSM_ST_UNKNOWN
[PATCH] libata: kill unnecessary sht->max_sectors initializations
[PATCH] libata: add missing sht->slave_destroy
...
Switch to pci_get_bus_and_slot because some x86 systems seem to be
handing us a device with dev->bus = NULL. Also don't apply the isa fixup
to revision C6 and later of the chip.
Really we need to work out wtf is handing us pdev->bus = NULL, but firstly
and more importantly we need the drivers working.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This was exposed by Al's recent header file dependency reduction
patches..
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[SUNHME]: Fix for sunhme failures on x86
[XFRM] xfrm_user: Better validation of user templates.
[DCCP] tfrc: Binary search for reverse TFRC lookup
[DCCP] ccid3: Deprecate TFRC_SMALLEST_P
[DCCP] tfrc: Identify TFRC table limits and simplify code
[DCCP] tfrc: Add protection against invalid parameters to TFRC routines
[DCCP] tfrc: Fix small error in reverse lookup of p for given f(p)
[DCCP] tfrc: Document boundaries and limits of the TFRC lookup table
[DCCP] ccid3: Fix warning message about illegal ACK
[DCCP] ccid3: Fix bug in calculation of send rate
[DCCP]: Fix BUG in retransmission delay calculation
[DCCP]: Use higher RTO default for CCID3
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6: (34 commits)
[S390] Don't use small stacks when lockdep is used.
[S390] cio: Use device_reprobe() instead of bus_rescan_devices().
[S390] cio: Retry internal operations after vary off.
[S390] cio: Use path verification for last path gone after vary off.
[S390] non-unique constant/macro identifiers.
[S390] Memory detection fixes.
[S390] cio: Make ccw_dev_id_is_equal() more robust.
[S390] Convert extmem spin_lock into a mutex.
[S390] set KBUILD_IMAGE.
[S390] lockdep: show held locks when showing a stackdump
[S390] Add dynamic size check for usercopy functions.
[S390] Use diag260 for memory size detection.
[S390] pfault code cleanup.
[S390] Cleanup memory_chunk array usage.
[S390] Misaligned wait PSW at memory detection.
[S390] cpu shutdown rework
[S390] cpcmd <-> __cpcmd calling issues
[S390] Bad kexec control page allocation.
[S390] Reset infrastructure for re-IPL.
[S390] Some documentation typos.
...
Make the m68knommu DMA handling consistent with other architectures.
Compile problems pointed out by Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove use of __rom_end symbol all together. This helps clean out the
miscellaneous symbols lying around in the m68knommu linker script.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here is a small patch to automatically detect the DRAM size on m520x.
It was generated against 2.6.17-uc0, and tested on an Intec 5208 dev board.
(This part of the patch if the memory register defines for the 520x
ColdFire CPU family - Greg).
Signed-off-by: Michael Broughton <mbobowik@telusplanet.net>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here is a small patch to automatically detect the DRAM size on m520x.
It was generated against 2.6.17-uc0, and tested on an Intec 5208 dev board.
Signed-off-by: Michael Broughton <mbobowik@telusplanet.net>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It turns out SHMAT, SHMDT, SHMGET and SHMCTL support in sys_ipc() for
m68knommu in 2.6 kernel(uClinux-dist-20060803 release) is missing.
(copied from m68k sources, report by David Wu <davidwu@arcturusnetworks.com>)
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes the following compile error with
CONFIG_BLK_DEV_INITRD=n and -Werror-implicit-function-declaration:
...
CC arch/m68knommu/kernel/setup.o
/home/bunk/linux/kernel-2.6/linux-2.6.18-rc5-mm1/arch/m68knommu/kernel/setup.c: In function 'setup_arch':
/home/bunk/linux/kernel-2.6/linux-2.6.18-rc5-mm1/arch/m68knommu/kernel/setup.c:268: error: implicit declaration of function 'paging_init'
make[2]: *** [arch/m68knommu/kernel/setup.o] Error 1
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The lock dependency validator adds a bunch of extra stack frames to
the stack, which can cause stack overflows. Especially seen on 31 bit
where the small stack is only 4k.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In io_subchannel_register(), it is better to just reprobe the current
device if it hasn't a driver yet than to rescan the whole bus.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If I/O was running on a just varied off chpid, it will be terminated.
If this was a common I/O layer internal I/O, it needs to be retried.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the last path to a device is gone after a chpid has been varied
off, putting it on the slow queue doesn't prevent a device driver
from still attempting to use it (it may stay on the slow queue for a
long time). Instead, trigger a verify event which will prevent I/O
attempts from the device driver immediately.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add some prefixes to constands defined in drivers/s390/net/qdio.h
and drivers/s390/lcs.h to make it possible to include the three
header files drivers/s390/net/qeth.h, drivers/s390/net/qdio.h and
drivers/net/s390/lcs.h in one C file. This is required for the
patch that generates the kerntypes.o file for use by lcrash.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
VMALLOC_END on 31bit should be 0x8000000UL instead of 0x7fffffffL.
The page mask which is used to make sure memory_end is on 4MB/2MB
boundary is wrong and not needed. Therefore remove it.
Make sure a vmalloc area does also exist and work on (future)
machines with 4TB and more memory.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Using memcmp to compare ccw_dev_id implies that the whole structure (incl.
padding) has always been completely initialized to sane values. Comparing
the structures field by field doesn't make such assumptions.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There's no need to have a spin_lock here, but need sleepable context
for vmem_map. Therefore convert the spin_lock into a mutex.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Set KBUILD_IMAGE to a sane value. This enables "make rpm"
Signed-off-by: Christian Borntraeger <cborntra@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Follow i386/x86_64:
lockdep can be used to print held locks when printing a
backtrace. This can be useful when debugging things like
'scheduling while atomic' asserts.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use a wrapper for copy_to/from_user to chose the best usercopy method.
The mvcos instruction is better for sizes greater than 256 bytes, if
mvcos is not available a page table walk is better for sizes greater
than 1024 bytes. Also removed the redundant copy_to/from_user_std_small
functions.
Signed-off-by: Gerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Avoid the tprot loop if diag260 works and reports that there are no
holes in memory. The tprot instruction can lead to a significant delay
in the ipl process if the virtual guest has a lot of memory and the
host is under memory pressure.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Need this at yet another file and don't want to add yet another
extern...
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the memory detection code would ever reach the point where it would
load the wait psw, it would generate a specification exception and the
system would crash at ipl time. This is because of a misaligned wait
psw. It needs to be on a double word boundary instead of a word
boundary.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Let one master cpu kill all other cpus instead of sending an external
interrupt to all other cpus so they can kill themselves.
Simplifies reipl/shutdown functions a lot.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case of reipl cpcmd gets called when all other cpus are not running
anymore. To prevent deadlocks change __cpcmd so that it doesn't take
any locks and call cpcmd or __cpcmd, whatever is correct in the current
context.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
KEXEC_CONTROL_MEMORY_LIMIT is an unsigned long value and therefore
should be defined as one. Otherwise the kexec control page can be
allocated above 2GB which will cause a specification exception on the
sam31 instruction in the s390 kexec relocation code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case of re-IPL and diag308 doesn't work we have to reset all devices
manually and wait synchronously that each reset finished.
This patch adds the necessary infrastucture and the first exploiter of it.
Subsystems that need to add a function that needs to be called at re-IPL
may register/unregister this function via
struct reset_call {
struct reset_call *next;
void (*fn)(void);
};
void register_reset_call(struct reset_call *reset);
void unregister_reset_call(struct reset_call *reset);
When the registered function get called the context is:
- all cpus beside the current one are stopped
- all machine checks and interrupts are disabled
- prefixing is disabled
- a default machine check handler is available for use
The registered functions may not take any locks are sleep.
For the common I/O layer part of this patch:
Introduce a reset_call css_reset that does the following:
- clear all subchannels
- perform a rchp on all channel paths and wait for the resulting
machine checks
This replaces the calls to clear_all_subchannels() and
cio_reset_channel_paths() for kexec and ccw reipl. reipl_ccw_dev() now
uses reipl_find_schid() to determine the subchannel id for a given
device id.
Also remove cio_reset_channel_paths() and friends since they are not
needed anymore.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
segment save will exit with a lock held if the passed segment doesn't
exist. Any subsequent call to segment_save will lead to a deadlock.
Fix this and give up the lock before returning.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
