The Allwinner A20 is a dual-core Cortex-A7-based SoC. It is
pin-compatible with the A10, and re-uses most of the IPs found in it,
plus some additional ones like a Gigabit Ethernet controller.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner A31 has a different watchdog, with a slightly different
register layout, that requires a different restart code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner A31 is a quad-Cortex-A7 based SoC, which shares a lot of
IPs with the previous SoCs from Allwinner, like the PIO, I2C, UARTs,
timers, watchdog IPs, but also differs by dropping the WEMAC ethernet
controller and most notably dropping the in-house IRQ controller in
favor of a ARM GIC one.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Since we've been a multi-platform enabled kernel from the beginning,
Makefile.boot has always been dead code.
Remove it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Preparing to move the parsing of reboot= to generic kernel code forces
the change in reboot_mode handling to use the enum.
[akpm@linux-foundation.org: fix arch/arm/mach-socfpga/socfpga.c]
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in
this branch, both containing almost no platform specific code at all,
since they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part of
the SoC specific code. With the changes done by Thomas Petazzoni, we can
now more easily have PCI host controller drivers as loadable modules and
keep them separate from the platform code in drivers/pci/host. This has
already led to the discovery that three platforms (exynos, spear and imx)
are actually using an identical PCIe host controller and will be able
to share a driver once support for spear and imx is added.
Conflicts:
* asm/glue-proc.h has one CPU type getting added that conflicts
with another addition in 3.10-rc7
* Simple context changes in arch/arm/Makefile and arch/arm/Kconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=0r9S
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC specific changes from Arnd Bergmann:
"These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and
EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in this
branch, both containing almost no platform specific code at all, since
they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part
of the SoC specific code. With the changes done by Thomas Petazzoni,
we can now more easily have PCI host controller drivers as loadable
modules and keep them separate from the platform code in
drivers/pci/host. This has already led to the discovery that three
platforms (exynos, spear and imx) are actually using an identical PCIe
host controller and will be able to share a driver once support for
spear and imx is added."
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (480 commits)
ARM: integrator: let pciv3 use mem/premem from device tree
ARM: integrator: set local side PCI addresses right
ARM: dts: Add pcie controller node for exynos5440-ssdk5440
ARM: dts: Add pcie controller node for Samsung EXYNOS5440 SoC
ARM: EXYNOS: Enable PCIe support for Exynos5440
pci: Add PCIe driver for Samsung Exynos
ARM: OMAP5: voltagedomain data: remove temporary OMAP4 voltage data
ARM: keystone: Move CPU bringup code to dedicated asm file
ARM: multiplatform: always pick one CPU type
ARM: imx: select syscon for IMX6SL
ARM: keystone: select ARM_ERRATA_798181 only for SMP
ARM: imx: Synertronixx scb9328 needs to select SOC_IMX1
ARM: OMAP2+: AM43x: resolve SMP related build error
dmaengine: edma: enable build for AM33XX
ARM: edma: Add EDMA crossbar event mux support
ARM: edma: Add DT and runtime PM support to the private EDMA API
dmaengine: edma: Add TI EDMA device tree binding
arm: add basic support for Rockchip RK3066a boards
arm: add debug uarts for rockchip rk29xx and rk3xxx series
arm: Add basic clocks for Rockchip rk3066a SoCs
...
Adds machine support for the Allwinner A10s SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=XZDd
-----END PGP SIGNATURE-----
Merge tag 'sunxi-core-for-3.11-2' of git://github.com/mripard/linux into next/soc
From Maxime Ripard:
Allwinner platform additions, take 2
Adds machine support for the Allwinner A10s SoC
* tag 'sunxi-core-for-3.11-2' of git://github.com/mripard/linux:
ARM: sunxi: Add Allwinner A10s machine compatible
Depends on the sunxi/cleanup branch
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The A10s is a SoC member of the Allwinner sun5i family. It is basically
an A13 with an EMAC and an HDMI controller.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
- Patches to remove the .init_irq definition when using irqchip_init
- Make the ARM core code call debug_ll_io_init when no map_io callback is
declared
- Remove the .map_io definition in the various machines using it
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=sNQl
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-cleanups-for-3.11' of git://github.com/mripard/linux into next/cleanup
From Maxime Ripard:
Cleanups in various machine definitions
- Patches to remove the .init_irq definition when using irqchip_init
- Make the ARM core code call debug_ll_io_init when no map_io callback is
declared
- Remove the .map_io definition in the various machines using it
(Some of these go through the platform maintainers, these are the ones who got
explicitly acked and not picked up by anyone else)
Signed-off-by: Olof Johansson <olof@lixom.net>
* tag 'arm-soc-cleanups-for-3.11' of git://github.com/mripard/linux:
ARM: sunxi: Remove the .map_io function declaration
ARM: mxs: remove the .map_io declaration
ARM: highbank: remove the .map_io declaration
ARM: mmu: Call debug_ll_io_init if no map_io function is specified
ARM: vt8500: Remove init_irq declaration in machine description
ARM: virt: Remove init_irq declaration in machine description
ARM: vexpress: Remove init_irq declaration in machine description
ARM: sirf: Remove init_irq declaration in machine description
ARM: spear: Remove init_irq declaration in machine description
ARM: nomadik: Remove init_irq declaration in machine description
debug_ll_io_init should be enough to map the needed addresses at boot,
so remove the trivial map_io code, and let the core call
debug_ll_io_init.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Commit ebafed7a ("ARM: irq: Call irqchip_init if no init_irq function is
specified") removed the need to explictly setup the init_irq field in
the machine description when using only irqchip_init. Remove that
declaration for sunxi as well.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
CONFIG_ARCH_SUNXI currently doesn't enable a gpiolib, which causes build
problems when building a kernel with only the sunxi platform enabled.
Select ARCH_REQUIRE_GPIOLIB to solve this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Emilio López <emilio@elopez.com.ar>
The Allwinner sun6i (A31) has a slightly different watchdog, that
doesn't allow to use the already existing restart code.
Rework a bit the restart code to allow to plug in more easily different
restart handlers depending on the device tree.
In the past, we were also meaning sunxi as a generic name covering all
Allwinner SoCs. This won't be true anymore with the A31 (sun6i) that
differs pretty much from sun4i and sun5i, and we will end up having
sunxi, for sun4i and sun5i, and sun6i, which is neither consistent nor
convenient. So, while we're at it, also change sunxi to sun4i.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This allows to remove some boilerplate code. At the same time, call the
set_handle_irq function in the initialization function of the irqchip,
so that we can remove it from the machine declaration.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
During the introduction of the Allwinner SoC platforms, sunxi was
initially meant as a generic name for all the variants of the Allwinner
SoC.
It was ok at the time of the support of only the A10 and A13 that
looks pretty much the same, but it's beginning to be troublesome with
the future addition of the Allwinner A31 (sun6i) that is quite
different, and would introduce some weird logic, where sunxi would
actually mean in some case sun4i and sun5i but without sun6i...
Moreover, it makes the compatible strings naming scheme not consistent
with other architectures, where usually for this kind of compability, we
just use the oldest SoC name that has this IP, so let's do just this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Using CLKSRC_OF allows to remove the SoC specific sunxi_timer.h header,
and instead of using a custom init function in the machine definition
use the standard clocksource_of_init function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A large number of cleanups, all over the platforms. This is dominated
largely by the Samsung platforms (s3c, s5p, exynos) and a few of the
others moving code out of arch/arm into more appropriate subsystems.
The clocksource and irqchip drivers are now abstracted to the point
where platforms that are already cleaned up do not need to even specify
the driver they use, it can all get configured from the device tree
as we do for normal device drivers. The clocksource changes basically
touch every single platform in the process.
We further clean up the use of platform specific header files here,
with the goal of turning more of the platforms over to being
"multiplatform" enabled, which implies that they cannot expose
their headers to architecture independent code any more.
It is expected that no functional changes are part of the cleanup.
The overall reduction in total code lines is mostly the result of
removing broken and obsolete code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=DvgJ
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"A large number of cleanups, all over the platforms. This is dominated
largely by the Samsung platforms (s3c, s5p, exynos) and a few of the
others moving code out of arch/arm into more appropriate subsystems.
The clocksource and irqchip drivers are now abstracted to the point
where platforms that are already cleaned up do not need to even
specify the driver they use, it can all get configured from the device
tree as we do for normal device drivers. The clocksource changes
basically touch every single platform in the process.
We further clean up the use of platform specific header files here,
with the goal of turning more of the platforms over to being
"multiplatform" enabled, which implies that they cannot expose their
headers to architecture independent code any more.
It is expected that no functional changes are part of the cleanup.
The overall reduction in total code lines is mostly the result of
removing broken and obsolete code."
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (133 commits)
ARM: mvebu: correct gated clock documentation
ARM: kirkwood: add missing include for nsa310
ARM: exynos: move exynos4210-combiner to drivers/irqchip
mfd: db8500-prcmu: update resource passing
drivers/db8500-cpufreq: delete dangling include
ARM: at91: remove NEOCORE 926 board
sunxi: Cleanup the reset code and add meaningful registers defines
ARM: S3C24XX: header mach/regs-mem.h local
ARM: S3C24XX: header mach/regs-power.h local
ARM: S3C24XX: header mach/regs-s3c2412-mem.h local
ARM: S3C24XX: Remove plat-s3c24xx directory in arch/arm/
ARM: S3C24XX: transform s3c2443 subirqs into new structure
ARM: S3C24XX: modify s3c2443 irq init to initialize all irqs
ARM: S3C24XX: move s3c2443 irq code to irq.c
ARM: S3C24XX: transform s3c2416 irqs into new structure
ARM: S3C24XX: modify s3c2416 irq init to initialize all irqs
ARM: S3C24XX: move s3c2416 irq init to common irq code
ARM: S3C24XX: Modify s3c_irq_wake to use the hwirq property
ARM: S3C24XX: Move irq syscore-ops to irq-pm
clocksource: always define CLOCKSOURCE_OF_DECLARE
...
The Allwinner SoCs have an IP module that handle both the muxing and the
GPIOs.
This IP has 8 banks of 32 bits, with a number of pins actually useful
for each of these banks varying from one to another, and depending on
the SoC used on the board.
This driver only implements the pinctrl part, the gpio part will come
eventually.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This creates irqchip initialization infrastructure from Thomas
Petazzoni. The VIC and GIC irqchip code is moved to drivers/irqchips
and adapted to use the new infrastructure. All DT enabled platforms
using GIC and VIC are converted over to use the new irqchip_init.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQ8ZobAAoJEMhvYp4jgsXiihIH/2VvxmSHZb0e3jN6AR0B42b7
9EwX0IE0B23t91hNTwdzzmTJQYA7pMmWkgHNfd3vIeqSepJAmrVv/gp4iM9CtPwE
KNh+kDWOK2ZsOH4Vb0lYRJHN8WQOIQHuCUr9+MdYLNOgf/pPL6G/Y9kv9A1e7fTC
W+tFRjC5N1ilZMGyowX12L1wnwDk6kHzed6YV6bskC17cZ9/pg8PhSVbM4A/3kAv
NXYKqbXJb+eCsWGXg/knZXOL6V9gBwvVYoe4O9X3nQ0226AWB9caad8l8tchAjRB
fmrYF1tbkpOWPnLxhvQy5b5MJichJgTMJHh7RgiEcc/3f63kOljjlx4QKiqHvT0=
=q7gm
-----END PGP SIGNATURE-----
Merge tag 'gic-vic-to-irqchip' of git://sources.calxeda.com/kernel/linux into next/cleanup
From Rob Herring:
Initial irqchip init infrastructure and GIC and VIC clean-ups
This creates irqchip initialization infrastructure from Thomas
Petazzoni. The VIC and GIC irqchip code is moved to drivers/irqchips
and adapted to use the new infrastructure. All DT enabled platforms
using GIC and VIC are converted over to use the new irqchip_init.
* tag 'gic-vic-to-irqchip' of git://sources.calxeda.com/kernel/linux:
irqchip: Move ARM vic.h to include/linux/irqchip/arm-vic.h
ARM: picoxcell: use common irqchip_init function
ARM: spear: use common irqchip_init function
irqchip: Move ARM VIC to drivers/irqchip
ARM: samsung: remove unused tick.h
ARM: remove unneeded vic.h includes
ARM: remove mach .handle_irq for VIC users
ARM: VIC: set handle_arch_irq in VIC initialization
ARM: VIC: shrink down vic.h
irqchip: Move ARM gic.h to include/linux/irqchip/arm-gic.h
ARM: use common irqchip_init for GIC init
irqchip: Move ARM GIC to drivers/irqchip
ARM: remove mach .handle_irq for GIC users
ARM: GIC: set handle_arch_irq in GIC initialization
ARM: GIC: remove direct use of gic_raise_softirq
ARM: GIC: remove assembly ifdefs from gic.h
ARM: mach-ux500: use SGI0 to wake up the other core
arm: add set_handle_irq() to register the parent IRQ controller handler function
irqchip: add basic infrastructure
irqchip: add to the directories part of the IRQ subsystem in MAINTAINERS
Fixed up massive merge conflicts with the timer cleanup due to adjacent changes:
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-bcm/board_bcm.c
arch/arm/mach-cns3xxx/cns3420vb.c
arch/arm/mach-ep93xx/adssphere.c
arch/arm/mach-ep93xx/edb93xx.c
arch/arm/mach-ep93xx/gesbc9312.c
arch/arm/mach-ep93xx/micro9.c
arch/arm/mach-ep93xx/simone.c
arch/arm/mach-ep93xx/snappercl15.c
arch/arm/mach-ep93xx/ts72xx.c
arch/arm/mach-ep93xx/vision_ep9307.c
arch/arm/mach-highbank/highbank.c
arch/arm/mach-imx/mach-imx6q.c
arch/arm/mach-msm/board-dt-8960.c
arch/arm/mach-netx/nxdb500.c
arch/arm/mach-netx/nxdkn.c
arch/arm/mach-netx/nxeb500hmi.c
arch/arm/mach-nomadik/board-nhk8815.c
arch/arm/mach-picoxcell/common.c
arch/arm/mach-realview/realview_eb.c
arch/arm/mach-realview/realview_pb1176.c
arch/arm/mach-realview/realview_pb11mp.c
arch/arm/mach-realview/realview_pba8.c
arch/arm/mach-realview/realview_pbx.c
arch/arm/mach-socfpga/socfpga.c
arch/arm/mach-spear13xx/spear1310.c
arch/arm/mach-spear13xx/spear1340.c
arch/arm/mach-spear13xx/spear13xx.c
arch/arm/mach-spear3xx/spear300.c
arch/arm/mach-spear3xx/spear310.c
arch/arm/mach-spear3xx/spear320.c
arch/arm/mach-spear3xx/spear3xx.c
arch/arm/mach-spear6xx/spear6xx.c
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/board-dt-tegra30.c
arch/arm/mach-u300/core.c
arch/arm/mach-ux500/board-mop500.c
arch/arm/mach-ux500/cpu-db8500.c
arch/arm/mach-versatile/versatile_ab.c
arch/arm/mach-versatile/versatile_dt.c
arch/arm/mach-versatile/versatile_pb.c
arch/arm/mach-vexpress/v2m.c
include/asm-generic/vmlinux.lds.h
Numerous includes of asm/hardware/vic.h aren't needed, so remove them.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Hubert Feurstein <hubert.feurstein@contec.at>
Cc: Alessandro Rubini <rubini@unipv.it>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: STEricsson <STEricsson_nomadik_linux@list.st.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Acked-By: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: linux-samsung-soc@vger.kernel.org
Cc: patches@opensource.wolfsonmicro.com
Acked-by: Arnd Bergmann <arnd@arndb.de>
Commit 6bb27d7 "ARM: delete struct sys_timer" removed struct sys_timer,
but didn't update mach-sunxi/sunxi.c for this change, even though the
sunxi timer implementation itself was updated. This caused a build break:
arch/arm/mach-sunxi/sunxi.c:94:2: error: unknown field 'timer' specified in initializer
arch/arm/mach-sunxi/sunxi.c:94:12: error: 'sunxi_timer' undeclared here (not in a function)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 68136b10 ("ARM: sunxi: Change device tree naming scheme for
sunxi") changed the naming scheme and the compatible strings used in the
device trees related to the sunXi platform, but forgot to change the
compatible string in the DT machine definition.
This prevents the kernel from booting on these boards.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
CC arch/arm/mach-sunxi/sunxi.o
./arch/arm/mach-sunxi/sunxi.c: In function 'sunxi_restart':
./arch/arm/mach-sunxi/sunxi.c:55:3: error: implicit declaration of function 'mdelay' [-Werror=implicit-function-declaration]
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds support for the Cubieboard based on the Allwinner
A10/sun4i SoC. Currently only UART is supported. Other devices
will eventually follow.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
