ATA_CBL_PATA_UNK indicates that the cable type can't be determined
from the host side and might be either 80c or 40c. libata applies
drive or other generic limit in this case. However, there are
controllers where both host and drive side detections are
misimplemented and the driver has to rely solely on private method -
peeking BIOS or ACPI configuration or using some other private
mechanism.
This patch adds ATA_CBL_PATA_IGN which tells libata to ignore the
cable type completely and just let the LLD determine the transfer mode
via host transfer mode masks and ->mode_filter().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jeff says xfer_mask is unsigned long not unsigned int. Convert all
xfermask fields and handling functions to deal with unsigned longs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_id_to_dma_mode() isn't quite generic. The function is basically
privately implemented ata_id_xfermask() combined with hardcoded mode
printing and configuration which are specific to ata_generic.
Kill the function and open code it in generic_set_mode() using generic
xfermode handling functions.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* s/ATA_BITS_(PIO|MWDMA|UDMA)/ATA_NR_\1_MODES/g
* Consistently use 0xff to indicate invalid transfer mode (0x00 is
valid for PIO_SLOW).
* Make ata_xfer_mode2mask() return proper mode mask instead of just
the highest bit.
* Sort ata_timing table in increasing xfermode order and update
ata_timing_find_mode() accordingly.
This patch doesn't introduce any behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Export the following xfermode related functions.
* ata_pack_xfermask()
* ata_unpack_xfermask()
* ata_xfer_mask2mode()
* ata_xfer_mode2mask()
* ata_xfer_mode2shift()
* ata_mode_string()
* ata_id_xfermask()
* ata_timing_find_mode()
These functions will be used later by LLD updates. While at it,
change unsigned short @speed to u8 @xfer_mode in
ata_timing_find_mode() for consistency.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATA_DFLAG_DUBIOUS_XFER is set whenever data transfer speed or method
changes and gets cleared when data transfer command succeeds in the
newly configured transfer mode.
This will be used to improve speed down logic.
Signed-off-by: Tejun Heo <htejun@gmail.com<
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move ata_set_mode() to libata-eh.c. ata_set_mode() is surely an EH
action and will be more tightly coupled with the rest of error
handling. Move it to libata-eh.c.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement protocol tests - ata_is_atapi(), ata_is_nodata(),
ata_is_pio(), ata_is_dma(), ata_is_ncq() and ata_is_data() and use
them to replace is_atapi_taskfile() and hard coded protocol tests.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I believe this version meets all Sergei's objections
Correct the logic for when we issue a set features for transfer mode
- If the device has IORDY and the controller has IORDY - set the mode
- If the device has IORDY and the controller does not - turn IORDY off
- If neither has IORDY do nothing
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Historically word 48 in the identify data was used to mean 32bit I/O
was supported for VLB IDE etc. ATA8 reassigns this word to the Trusted
Computing Group, where it is used for TCG features. This means that
an ATA8 TCG drive is going to trigger 32bit I/O on some systems which
will be funny.
Anyway we need to sort this out ready for ATA8 so:
- Reorder the ata.h header a bit so the ata_version function occurs early
in it
- Make dword_io check the ATA version
- Add an ATA8 version checking TCG presence test
While we are at it the current drafts have a flaw where it may not be
possible to disable TCG features at boot (and opt out of the trusted
model) as TCG intends because it relies on presence of a different
optional feature (DCS). Handle this in software by refusing the TCG
commands if libata.allow_tpm is not set. (We must make it possible
as some environments such as proprietary VDR devices will doubtless
want to use it to lock up content)
Finally as with CPRM print a warning so that the user knows they may
not be able to full access and use the device.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With ATAPI transfer chunk size properly programmed, libata PIO HSM
should be able to handle full spurious data chunks. Also, it's a good
idea to suppress trailing data warning for misc ATAPI commands as
there can be many of them per command - for example, if the chunk size
is 16 and the drive tries to transfer 510 bytes, there can be 31
trailing data messages.
This patch makes the following updates to libata ATAPI PIO HSM
implementation.
* Make it drain full spurious chunks.
* Suppress trailing data warning message for misc commands.
* Put limit on how many bytes can be drained.
* If odd, round up consumed bytes and the number of bytes to be
drained. This gets the number of bytes to drain right for drivers
which do 16bit PIO.
This patch is partial backport of improve-ATAPI-data-xfer patchset
pending for #upstream.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add two hooks - ata_acpi_dissociate() which is called during driver
detach after the whole host is shutdown and ata_acpi_on_disable()
which is called when a device is disabled.
Signed-off-by: Tejun heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_port_detach() calls ata_dev_disable() with host lock held but
ata_dev_disable() should be called from EH context. ata_port_detach()
steals EH context by setting ATA_PFLAG_UNLOADAING and flushing EH.
Drop locking around ata_dev_disable() and note that ata_port_detach()
owns EH context at that point.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Like ST380817AS / 3.42, ST3160023AS / 3.42 times out commands if NCQ
is used. Blacklist it. This is reported by Matheus Izvekov in the
following thread.
http://thread.gmane.org/gmane.linux.ide/24202
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Matheus Izvekov <mizvekov@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
link->eh_info.serror is used to cache SError for controllers which
need it cleared from interrupt handler to clear IRQ. It also should
be cleared after reset just like SError itself.
Make ata_std_postreset() clear link->eh_info.serror too and update
sata_sil such that it doesn't care about bookkeeping the value.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Spurious NCQ completion detection implemented in ahci was incorrect.
On AHCI receving and processing FISes and raising interrupts are not
interlocked and spurious interrupts are expected.
For example, if an interrupt occurs while interrupt handler is running
and the running interrupt handler handles the event the new IRQ
indicated, after IRQ handler finishes, it will be executed again
because IRQ pending bit is set by the new interrupt but there won't be
anything to process.
Please read the following message for more information.
http://article.gmane.org/gmane.linux.ide/26012
This patch...
* Removes all spurious IRQ whining from ahci. Spurious NCQ completion
detection was completely wrong. Spurious D2H Register FIS taught us
that some early drives send spurious D2H Register FIS with I bit set
while NCQ commands are in progress but none of recent drives does
that and even the ones which show such behavior can do NCQ fine.
* Kills all NCQ blacklist entries which were added because of spurious
NCQ completions. I tracked down each commit and verified all
removed ones are actually added because of spurious completions.
WD740ADFD-00NLR1 wasn't deleted but moved upward because the drive
not only had spurious NCQ completions but also is slow on sequential
data transfers if NCQ is enabled.
Maxtor 7V300F0 was added by 0e3dbc01d5
from Alan Cox. I can only find evidences that the drive only had
troubles with spuruious completions by searching the mailing list.
This entry needs to be verified and removed if it doesn't have other
NCQ related problems.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On Fri, 30 Nov 2007 14:34:11 +0200 (EET)
Meelis Roos <mroos@linux.ee> wrote:
> > Can you stick a stack trace in at that point ? That would help diagnose
> > it a great deal quicker.
>
> Finally done - found out hard way that BUG() is too bad and
> dump_st5ack() suits me better.
Thanks. This should fix the real cause, and also allow for port start to
fail politely with -ENODEV.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata: Add more TSST (Samsung/Toshiba) IDE drives with broken
cable detection validation bits.
signed-off-by: Peter Missel (peter.missel@onlinehome.de)
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Per Mark's comments, maybe all ATAPI tape drives need ATA_HORKAGE_STUCK_ERR.
This patch applys ATA_HORKAGE_STUCK_ERR for all ATAPI tape drives.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Tejun Heo <htejun@gmail.com>
After an error condition, some ATAPI tape drives set DRQ=1 together
with ERR=1 when asking the host to transfer the CDB of the next packet
command (i.e. request sense). This patch, a revised version of
Alan/Mark's previous patch, adds ATA_HORKAGE_STUCK_ERR to workaround
the problem by ignoring the ERR bit and proceed sending the CDB.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Port / host stop calls used to be made from ata_host_release() which
is called after all hardware resources acquired after host allocation
are released. This is wrong as port and host stop routines often
access the hardware.
Add separate devres for port / host stop which is invoked right after
IRQ is released but with all other hardware resources intact. The
devres is added iff ->host_stop and/or ->port_stop exist.
This problem has been spotted by Mark Lord.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In a presentation of true workmanship, pata_ali asserts IRQ
permanantly if the TF status register is read more than once when
there's no device attached to the port.
Avoid waiting polling for !0xff if it's PATA. It's needed only for
some rare SATA devices anyway.
This problem is reported by Luca Tettamanti in bugzilla bug 9298.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Tested-By: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
By default ata_host_activate() expects a valid IRQ in order to
successfully register the host. This patch enables a special case
for registering polling-only hosts that either don't have IRQs
or have buggy IRQ generation (either in terms of handling or
sensing), which otherwise work fine.
Hosts that want to use polling mode can simply set ATA_FLAG_PIO_POLLING
and pass in an invalid IRQ.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
One or two ancient drives predated the cable spec and didn't sent the
valid bits for the field. I had hoped to leave this out of libata as a
piece of historical annoyance but a recent CD drive shows the same bug so
we have to import support for it.
Same concept as Bartlomiej's changes old IDE except that as we have
centralised blacklists we can avoid keeping another private table of stuff
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
LPM seems to get hung up while disabling DIPM, and after thinking
about this a bit, I don't think we really need to manually disable it
anyway.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There's nothing to be gained by configuring downstream links faster
than the upstream link and such configurations cause problems on
certain PMPs. Limit downstream link speed by the upstream link speed.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In sata_set_spd_needed(), if SControl read failed, it returned 0 and
skipped PHY speed configuration. However, if SControl access fails,
it's far more logical to request PHY speed configuration. Reverse the
logic.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Commands sent to ATAPI tape drives via the SCSI generic (sg) driver are
limited in the amount of data that they can transfer by the max_sectors
value. The max_sectors value is currently calculated according to the
command set for disk drives, which doesn't apply to tape drives. The
default max_sectors value of 256 limits ATAPI tape drive commands to
128 KB. This patch against 2.6.24-rc1 increases the max_sectors value
for tape drives to 65535, which permits tape drive commands to transfer
just under 32 MB.
Tested with a SuperMicro PDSME motherboard, AHCI, and a Sony SDX-570V
SATA tape drive.
Note that some of the chipset drivers also set their own max_sectors
value, which may override the value set in libata-core. I don't have
any of these chipsets to test, so I didn't go messing with them. Also,
ATAPI devices other than tape drives may benefit from similar changes,
but I have only tape drives and disk drives to test.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/ata/libata-core.c:768: warning: 'ata_lpm_enable' defined but not used
drivers/ata/libata-core.c:784: warning: 'ata_lpm_disable' defined but not used
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'alpm' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] AHCI: add hw link power management support
[libata] Link power management infrastructure
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] AHCI: fix newly introduced host-reset bug
[libata] sata_nv: fix SWNCQ enabling
libata: add MAXTOR 7V300F0/VA111900 to NCQ blacklist
libata: no need to speed down if already at PIO0
libata: relocate forcing PIO0 on reset
pata_ns87415: define SUPERIO_IDE_MAX_RETRIES
[libata] Address some checkpatch-spotted issues
[libata] fix 'if(' and similar areas that lack whitespace
libata: implement ata_wait_after_reset()
libata: track SLEEP state and issue SRST to wake it up
libata: relocate and fix post-command processing
Device Initiated Power Management, which is defined
in SATA 2.5 can be enabled for disks which support it.
This patch enables DIPM when the user sets the link
power management policy to "min_power".
Additionally, libata drivers can define a function
(enable_pm) that will perform hardware specific actions to
enable whatever power management policy the user set up
for Host Initiated Power management (HIPM).
This power management policy will be activated after all
disks have been enumerated and intialized. Drivers should
also define disable_pm, which will turn off link power
management, but not change link power management policy.
Documentation/scsi/link_power_management_policy.txt has additional
information.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
MAXTOR 7V300F0/VA111900 does spurious NCQ completions. Add it to
blacklist. This problem is reported by Carsten Otto.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Carsten Otto <c-otto@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Forcing PIO0 on reset was done inside ata_bus_softreset(), which is a
bit out of place as it should be applied to all resets - hard, soft
and implementation which don't use ata_bus_softreset(). Relocate it
such that...
* For new EH, it's done in ata_eh_reset() before calling prereset.
* For old EH, it's done before calling ap->ops->phy_reset() in
ata_bus_probe().
This makes PIO0 forced after all resets. Another difference is that
reset itself is done after PIO0 is forced.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On certain device/controller combination, 0xff status is asserted
after reset and doesn't get cleared during 150ms post-reset wait. As
0xff status is interpreted as no device (for good reasons), this can
lead to misdetection on such cases.
This patch implements ata_wait_after_reset() which replaces the 150ms
sleep and waits upto ATA_TMOUT_FF_WAIT if status is 0xff.
ATA_TMOUT_FF_WAIT is currently 800ms which is enough for
HHD424020F7SV00 to get detected but not enough for Quantum GoVault
drive which is known to take upto 2s.
Without parallel probing, spending 2s on 0xff port would incur too
much delay on ata_piix's which use 0xff to indicate empty port and
doesn't have SCR register, so GoVault needs to wait till parallel
probing.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATA devices in SLEEP mode don't respond to any commands. SRST is
necessary to wake it up. Till now, when a command is issued to a
device in SLEEP mode, the command times out, which makes EH reset the
device and retry the command after that, causing a long delay.
This patch makes libata track SLEEP state and issue SRST automatically
if a command is about to be issued to a device in SLEEP.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Bruce Allen <ballen@gravity.phys.uwm.edu>
Cc: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some commands need post-processing after successful completion. This
was done in ata_scsi_qc_complete() till now but this has the following
problems.
* Post-command processing gets executed when qc is completed from EH.
Some qc's are retried from EH with zero err_mask and thus triggers
unnecessary/incorrect post-command processing.
* Command post processing doesn't belong to SAT layer.
* Link-wide revalidation was scheduled where device revalidation
suffices.
This patch moves post-command processing to success completion path of
ata_qc_complete() which is travelled iff the command is going to be
completed without passing through EH and updates post-command
processing such that device-specific action is used. While at it,
restructure code a bit for readability.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After turning on DEBUG_SG I hit a fail:
kernel BUG at include/linux/scatterlist.h:50!
ata_qc_issue
ata_scsi_translate
ipr_queuecommand
scsi_dispatch_cmd
scsi_request_fn
elv_insert
blk_execute_rq_nowait
blk_execute_rq
sg_io
scsi_cmd_ioctl
cdrom_ioctl
sr_block_ioctl
blkdev_driver_ioctl
blkdev_ioctl
block_ioctl
do_ioctl
vfs_ioctl
sys_ioctl
sg_ioctl_trans
It looks like ata_sg_setup is working on an uninitialised sg table. Call
sg_init_table to initialise it before use.
Signed-off-by: Anton Blanchard <anton@samba.org>
Note: this patch will fix it, but you could also get away with just
doing the sg_init_table() once at qc creation time.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* 'sg' of git://git.kernel.dk/linux-2.6-block:
fix sg_phys to use dma_addr_t
ub: add sg_init_table for sense and read capacity commands
x86: pci-gart fix
blackfin: fix sg fallout
xtensa: dma-mapping.h is using linux/scatterlist.h functions, so include it
SG: audit of drivers that use blk_rq_map_sg()
arch/um/drivers/ubd_kern.c: fix a building error
SG: Change sg_set_page() to take length and offset argument
AVR32: Fix sg_page breakage
mmc: sg fallout
m68k: sg fallout
More SG build fixes
sg: add missing sg_init_table calls to zfcp
SG build fix
I guess Windows didn't care about the command so neither did they
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Most drivers need to set length and offset as well, so may as well fold
those three lines into one.
Add sg_assign_page() for those two locations that only needed to set
the page, where the offset/length is set outside of the function context.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Another one doing spurious NCQ completions. Blacklist it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Did a complete audit of these and found we have another error case.
ata_bus_softreset calls ata_check_status which means that it tries to do
an ioread8 on the port blindly and check versus 0xFF for an error.
It should of course be using the ap->ops method for this via chk_status,
and this bug causes a wrog status call on the NS87415 at least.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
