Allows to perform monitor dumping on AX210 device family
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
mac80211 sets max amsdu to min supported ht vs vht but TLC only works
with one mode so we can set to the exact mode used (vht/ht)
and enable larger amsdu sizes for vht.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The layout of the RBD (receive buffer descriptor) isn't quite right,
the hardware ended up being implemented differently. Switch to the
correct RBD layout. While at it, remove the now useless extra defines.
Also, switch the CD (completion descriptor) to the right format, which
is basically just a code cleanup because the only field we really used
(rbid) is still in the same place. We may need fragmentation later if
we ever want to use it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In restart flow, the driver requests HW restart from mac80211
and then mac80211 uses a worker to do the restart flow. In that flow a
sync dump is performed. Instead, schedule the dump worker before
requesting HW restart from mac80211. This approach simplifies the
restart flow.
Also, it is neeeded in order to differentiate between the handling of SW
and HW errors in a future commit.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Only add the size of the tx command to the dump file size if it is set
in the dump_mask.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Newer FWs use a new format of the SCAN_OFFLOAD_PROFILES_QUERY_RSP,
which now supports indicating match on an higher number of channels.
Modify the code to support both the old format and the newer one,
based on a FW TLV.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support REGULATORY_NVM_GET_INFO_RSP_API_S_VER_4.
This API adds the new 6-7GHz channels.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add UHB (ultra high band) channels and use 16 bit variables
to fit the new channels.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If number of channels in the driver is greater than
number of scan channels given by firmware TLV, do not
fail scan config, but adjust to firmware's number of channels.
This is helpful for supporting in driver new channels before
it being supported by firmware scan.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For some reason we never enabled it, but it appears to work fine.
Enable it now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Set the capabilities flags and inform firmware
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are some buggy APs that keeps changing the count while forcing
us to block TX. This eventually results in queue hang, assert, and
disconnection. Detect such APs and disconnect gracefully in advance.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case we receive channel switch announcement with immediate
quiet and unknown switching time, we will switch when FW identifies
AP left channel. However, if AP remains on channel, we will
eventually get TX queue hang. Init a work to disconnect if
switch doesn't occur within 1500 milliseconds. Do it also
for a too long channel switch.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Let FW know if quiet mode is on or not. This is needed
in order to disable it in FW when CSA is complete.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Send to FW modify command for every beacon we receive during channel
switch. FW will track the count, and make sure the event is scheduled
in time even if AP changed count.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Report all NO_DATA events to mac80211 so they get captured
in radiotap for usage in sniffer scenarios; map the info
type to a reasonable radiotap type for this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case we receive abort operation for CSA, clean up
our state.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support passing to FW delayed beacon count. This
represents the delay the AP can have when moving to
the new channel.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
ies1 or ies2 might be null when code inside
_wil_cfg80211_merge_extra_ies access them.
Add explicit check for null and make sure ies1/ies2 are not
accessed in such a case.
spos might be null and be accessed inside
_wil_cfg80211_merge_extra_ies.
Add explicit check for null in the while condition statement
and make sure spos is not accessed in such a case.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HALP ICR is set as long as the FW should stay awake.
To prevent its multiple handling the driver masks this IRQ bit.
However, if there is a different MISC ICR before the driver clears
this bit, there is a risk of race condition between HALP mask and
unmask. This race leads to HALP timeout, in case it is mistakenly
masked.
Add an atomic flag to indicate if HALP ICR should be handled.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Upon status ring handling, in case there are both unicast and
multicast (cid == max) status messages to handle, wrong sta statistics
might get updated.
Fix this by setting stats to NULL upon invalid cid
(e.g. == max_assoc_sta).
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rearrange the code by having functions to access 802.3 header
members, source and destination addresses.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
New FW added support for upto 20 clients in AP mode. Change the driver
to support this as well. FW reports it's max supported associations in
WMI_READY_EVENT. Some WMI commands/events use cidxtid field which is
limited to 16 cids. Use new cid/tid fields instead.
For Rx packets cid from rx descriptor is limited to 3 bits (0..7),
to find the real cid, compare transmitter address with the stored
stations mac address in the driver sta array.
EDMA FW still supports 8 stations. Extending the support to 20
stations will come later.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In AP mode with multiple clients, driver stops net queue
(netif_tx_stop_queue) upon first ring (serving specific client)
becoming full. This can have negative effect on transmission to
other clients which may still have room in their corresponding rings.
Implement new policy in which stop/wake net queue are not used. In
case there is no room in the ring for a transmitted packet, drop the
packet.
New policy can be helpful to debug performance issues, to guarantee
maximum utilization of net queues.
New policy is disabled by default and can be enabled by debugfs:
echo 1 > drop_if_ring_full
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Due to a HW issue in PHY info collection rtap_include_phy_info is not
in use, hence can be removed.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, rx_duration for each peer is not getting populated in
fw_stats debugfs entry for WCN3990.
WCN3990 firmware sends rx duration for each peer as part of
peer_extd_stats in WMI_UPDATE_STATS_EVENT. To enable peer_extd_stats,
firmware expects host to send fw_stats_req_mask with flag
WMI_TLV_PEER_STATS_EXTD set in WMI_REQUEST_STATS_CMD.
Send fw_stats_req_mask with flag WMI_TLV_PEER_STATS_EXTD set in
WMI_REQUEST_STATS_CMD and parse the peer_extd_stats in
WMI_UPDATE_STATS_EVENT to populate the rx_duration of each peer
in fw_stats debugfs entry.
Currently the driver handles 32-bit rx_duration, but the rx_duration
for WCN3990 can be upto 63 bit. The firmware sends rx_duration split
into two 32-bit fields, with the upper 32-bits being valid only if its
MSB is set. This change handles the 63-bit rx_duration obtained from
WCN3990 and maintain the backward compatibility.
To get the rx_duration of each connected peer :
cat /sys/kernel/debug/ieee80211/phyX/ath10k/fw_stats
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ht_idx (ht rate index) and idx (rate table index) are calculated based on
mcs index. This mcs index used in the above calculation should be 0-9 for
getting the correct ht_idx and idx.
Currently the mcs index used for the above calculations is mcs index which
can be 0-31 (in case of HT), leading to incorrect rate index and ht index values.
Fix the issue by obtaining mcs value from the ratecode reported by firmware
and use it for calculating ht_idx and idx (rate-table index).
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: e88975ca37 ("ath10k: dump tx stats in rate table format")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The SGI is updated wrongly in tx stats table in debugfs per sta
entry. To know whether the packets/bytes are sent with SHORT GI,
test whether the SGI bit(ATH10K_RATE_INFO_FLAGS_SGI_BIT) is set or
not in the txrate flags.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: a904417fc8 ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, the bandwidth is updated wrongly in BW table in tx_stats
debugfs per sta as there is difference in number of bandwidth type
in mac80211 and driver stats table. This leads to bandwidth getting
updated at wrong index in bandwidth table in tx_stats.
Fix this index mismatch between mac80211 and driver stats table (BW table)
by making the number of bandwidth type in driver compatible with mac80211.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: a904417fc8 ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The NSS data is updated incorrectly in the tx stats as the array
indexing starts from zero.
Fix the incorrect updation of NSS data in tx_stats by taking into
consideration the array index starting from zero.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: a904417fc8 ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8192se/fw.c: In function '_rtl92s_firmware_downloadcode':
drivers/net/wireless/realtek/rtlwifi/rtl8192se/fw.c:139:17: warning:
variable 'seg_ptr' set but not used [-Wunused-but-set-variable]
It's not used after commit 59ae1d127a ("networking: introduce and use
skb_put_data()")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/hal_btc.c: In function '_rtl8723e_dm_bt_coexist_2_ant':
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/hal_btc.c:1408:5: warning:
variable 'bt_retry_cnt' set but not used [-Wunused-but-set-variable]
It's never used and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8723be/dm.c: In function 'rtl8723be_dm_check_edca_turbo':
drivers/net/wireless/realtek/rtlwifi/rtl8723be/dm.c:998:7: warning:
variable 'b_last_is_cur_rdlstate' set but not used [-Wunused-but-set-variable]
It's never used and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The call to of_find_node_by_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/net/wireless/mediatek/mt76/eeprom.c:58:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 48, but without a corresponding object release within this function.
./drivers/net/wireless/mediatek/mt76/eeprom.c:61:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 48, but without a corresponding object release within this function.
./drivers/net/wireless/mediatek/mt76/eeprom.c:67:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 48, but without a corresponding object release within this function.
./drivers/net/wireless/mediatek/mt76/eeprom.c:70:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 48, but without a corresponding object release within this function.
./drivers/net/wireless/mediatek/mt76/eeprom.c:72:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 48, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The following types of blank line problems are reported:
WARNING: Missing a blank line after declarations
CHECK: Please don't use multiple blank lines
There are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The following problems were found:
WARNING: Missing a blank line after declarations
CHECK: Please don't use multiple blank lines
CHECK: Please use a blank line after function/struct/union/enum declarations
There are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The problems filed include the following:
WARNING: Missing a blank line after declarations
CHECK: Please don't use multiple blank lines
There are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The types of problems fixed are as follows:
WARNING: Missing a blank line after declarations
CHECK: Please use a blank line after function/struct/union/enum declarations
CHECK: Please don't use multiple blank lines
There are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The errors consist of multiple blank lines, and a missing blank line
after the declarations.
There are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The instances where statement continuations are improperly aligned have
been fixed.
There are no changes to generated code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Checkpatch.pl reports a number of problems with block comments.
These changes do not affect the generated code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Checkpatch.pl report problems in wifi.h where spaces are missing, as well
as extraneous spaces.
There are no changes in the generated code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The call to ieee80211_probereq_get can return NULL if a skb allocation
fails, so add a null pointer check and free an earlier skb on the error
exit return path.
Fixes: 7fdcb8e126 ("rsi: add support for hardware scan offload")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware may report general errors using a special message type. Add
basic support for it by simply decoding & printing an error number.
A sample situation in which firmware reports a buf error:
CONSOLE: 027084.733 no host response IOCTL buffer available..so fail the request
will now produce a "Firmware reported general error: 9" on the host.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This updates host struct to match the in-firmawre definition. It's a
cosmetic change as it only applies to the reserved struct space.
Fixes: c988b78244 ("brcmfmac: print firmware reported ring status errors")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/ath9k/recv.c: In function 'ath_rx_count_airtime':
drivers/net/wireless/ath/ath9k/recv.c:1010:18: warning:
variable 'acq' set but not used [-Wunused-but-set-variable]
It's not used after 89cea7493a ("ath9k: Switch to mac80211 TXQ scheduling
and airtime APIs"). Also remove related variables.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since ath9k reports airtime usage directly using the
ieee80211_report_airtime() callback, it shouldn't also report it using the
tx_time in status. Make sure the field is zeroed before TX status is
reported to avoid spurious airtime being accounted by bits being left over
from earlier uses of the cb.
Fixes: 89cea7493a ("ath9k: Switch to mac80211 TXQ scheduling and airtime APIs")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
