Add improved logic to detect the exact CX2388[578] A/V core that is being
probed. Also cleaned up detection and logging for CX2310[12], CX2583[67],
and CX2584[0123] cores and chips.
Also added code to identify a CX2388[578] A/V decoder core that is not
responding properly. Typical symptoms include registers 0x00-0xff
responding properly but all other registers returning the same value
(0x13 and 0x5 have been observed). This state will cause proper detection of
'885 vs. '887 vs. '888 to fail and the chip won't respond to get configured
properly anyway. I have no method of reseting the core to a working state at
this time; but I didn't try too hard to work one out either. The problem
likely only occurs in development. I suspect configuring the SYS PLL VCO to
oscillate too slowly (286.3 MHz?) before post divide may be the root cause,
when encountered.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change adds a skeletal implementation of a v4l2_subdevice to provide
encapsulation and abstraction of the CX23888's integrated consumer infrared
controller. This change also instantiates the cx23888_ir subdev for the
HVR-1850 which has IR hardware physically wired up to a CX23888.
The cx23888_ir subdev code is being written with long-term objectives to:
1. port it to the cx25840 module for the CX2584x, CX2583x, CX23885, & CX231xx
IR controllers
2. possibly port it to the cx18 module for the CX23418 IR controller
3. have the IR subdevice accessed abstractly in the cx23885 module, so the
driver can ignore the difference between the CX23885 and CX23888.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This changes corrects the ioctl() operations for both the CX2388[578] analog
video and MPEG video device nodes to properly and consistently support
VIDIOC_G_CHIP_IDENT, VIDIOC_DBG_G_REGISTER and VIDIOC_DBG_S_REGISTER ioctl()s.
This caused some ioctl() support routines to be broken out into a separate
source file.
Now v4l2-dbg can be used to manipulate CX2388[578] and CX23417 registers
including the CX2388[57] functions handled by the cx25840 module.
This was done in anticipation of developing a new v4l2_subdev for the
integrated IR controller of the CX23888.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add identifiers for CX2388[578] chips, CX2310[012] chips, integrated
A/V decoders cores, integrated IR controller core, and the CX23417
MPEG encoder. The cx23885 module and cx25840 module will use these
identifiers in upcoming changes.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The board support has been validated by the user, so get rid of the warning
that shows up on board load.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dmitri's patch for the Behold X7 didn't use the #define I had setup for
XC5000_RADIO_FM1, so cut over to using that instead of "1".
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the digital side of the Behold X7
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make analog audio, dvb and the remote work on a Terratec Cinergy Hybrid
XS (em2882).
Note by djh: Thanks go out fo Andrej Suligoi for his contribution in providing
and testing pretty much the exact same patch as provided by Uros. Between
the two of them, they got all the core functionality working for the device.
Cc: Andrej Suligoi <suligoi@gmail.com>
Signed-off-by: Uroš Vampl <mobile.leecher@gmail.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Seems that the reference design used for the KWorld 2800d switched from the
em2860 to em2862, so we need to add the new USB id (and the i2c hash remains
so all we need is the default em2862 id.
Thanks to Ian Young for reporting the issue and testing the fix.
Cc: Ian Young <ian@duffrecords.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove hard-coded definition of the xc5000 FM radio input, making it a
parameter passed in when doing the attach call.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set radio frequency only upon success.
Signed-off-by: David Ellingsworth <david@identd.dyndns.org>
Acked-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Preserve radio state during suspend/resume.
Signed-off-by: David Ellingsworth <david@identd.dyndns.org>
Acked-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ensure the radio is initialized to a consistent state.
Signed-off-by: David Ellingsworth <david@identd.dyndns.org>
Acked-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Looks like eeprom IR mode byte value 0x04 means there is remote
which should be polled. Patch enables polling also in case of 0x04.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support for MSI DIGIVOX mini III remote.
Thanks to Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
Thanks to Roman <lists@hasnoname.de>
Cc: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
Cc: Roman <lists@hasnoname.de>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add USB ID 1b80:c161 for KWorld PlusTV DVB-T PCI Pro Card (DVB-T PC160-T).
Thanks to Andrew Cruickshank <atcrank@gmail.com> for reporting this.
Cc: Andrew Cruickshank <atcrank@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Update the dib7000p:
The status is HAS_LOCK only if the demod is able to decode the TPS. Sometimes, there is a TPS data lock, even if the demod is not able to decode it (ex: no RF signal).
For the STK7770P: correct value for the charge pump
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dib7000p/dib8000: added pid filtering
dib8000: the SNR is in 10th of dB (not in dB)
dib7000p and dib8000: added the pid filtering. This feature is enabled by module option (dvb-usb module).
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This IR uses NEC protocol. In order to use, dvb_usb_dib0700_ir_proto=0
should be used.
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, dvb_usb_dib0700_ir_proto is supported only with firmwares
older than 1.2. Adds support for it also with the newer firmware.
This is needed in order to support PixelView SBTVD IR.
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'tracing-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (40 commits)
tracing: Separate raw syscall from syscall tracer
ring-buffer-benchmark: Add parameters to set produce/consumer priorities
tracing, function tracer: Clean up strstrip() usage
ring-buffer benchmark: Run producer/consumer threads at nice +19
tracing: Remove the stale include/trace/power.h
tracing: Only print objcopy version warning once from recordmcount
tracing: Prevent build warning: 'ftrace_graph_buf' defined but not used
ring-buffer: Move access to commit_page up into function used
tracing: do not disable interrupts for trace_clock_local
ring-buffer: Add multiple iterations between benchmark timestamps
kprobes: Sanitize struct kretprobe_instance allocations
tracing: Fix to use __always_unused attribute
compiler: Introduce __always_unused
tracing: Exit with error if a weak function is used in recordmcount.pl
tracing: Move conditional into update_funcs() in recordmcount.pl
tracing: Add regex for weak functions in recordmcount.pl
tracing: Move mcount section search to front of loop in recordmcount.pl
tracing: Fix objcopy revision check in recordmcount.pl
tracing: Check absolute path of input file in recordmcount.pl
tracing: Correct the check for number of arguments in recordmcount.pl
...
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: Fix trace_marker output
tracing: Fix event format export
tracing: Fix return value of tracing_stats_read()
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (31 commits)
rcu: Make RCU's CPU-stall detector be default
rcu: Add expedited grace-period support for preemptible RCU
rcu: Enable fourth level of TREE_RCU hierarchy
rcu: Rename "quiet" functions
rcu: Re-arrange code to reduce #ifdef pain
rcu: Eliminate unneeded function wrapping
rcu: Fix grace-period-stall bug on large systems with CPU hotplug
rcu: Eliminate __rcu_pending() false positives
rcu: Further cleanups of use of lastcomp
rcu: Simplify association of forced quiescent states with grace periods
rcu: Accelerate callback processing on CPUs not detecting GP end
rcu: Mark init-time-only rcu_bootup_announce() as __init
rcu: Simplify association of quiescent states with grace periods
rcu: Rename dynticks_completed to completed_fqs
rcu: Enable synchronize_sched_expedited() fastpath
rcu: Remove inline from forward-referenced functions
rcu: Fix note_new_gpnum() uses of ->gpnum
rcu: Fix synchronization for rcu_process_gp_end() uses of ->completed counter
rcu: Prepare for synchronization fixes: clean up for non-NO_HZ handling of ->completed counter
rcu: Cleanup: balance rcu_irq_enter()/rcu_irq_exit() calls
...
* 'core-printk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ratelimit: Make suppressed output messages more useful
printk: Remove ratelimit.h from kernel.h
ratelimit: Fix/allow use in atomic contexts
ratelimit: Use per ratelimit context locking
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
mutex: Fix missing conditions to build mutex_spin_on_owner()
mutex: Better control mutex adaptive spinning config
locking, task_struct: Reduce size on TRACE_IRQFLAGS and 64bit
locking: Use __[SPIN|RW]_LOCK_UNLOCKED in [spin|rw]_lock_init()
locking: Remove unused prototype
locking: Reduce ifdefs in kernel/spinlock.c
locking: Make inlining decision Kconfig based
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (63 commits)
x86, Calgary IOMMU quirk: Find nearest matching Calgary while walking up the PCI tree
x86/amd-iommu: Remove amd_iommu_pd_table
x86/amd-iommu: Move reset_iommu_command_buffer out of locked code
x86/amd-iommu: Cleanup DTE flushing code
x86/amd-iommu: Introduce iommu_flush_device() function
x86/amd-iommu: Cleanup attach/detach_device code
x86/amd-iommu: Keep devices per domain in a list
x86/amd-iommu: Add device bind reference counting
x86/amd-iommu: Use dev->arch->iommu to store iommu related information
x86/amd-iommu: Remove support for domain sharing
x86/amd-iommu: Rearrange dma_ops related functions
x86/amd-iommu: Move some pte allocation functions in the right section
x86/amd-iommu: Remove iommu parameter from dma_ops_domain_alloc
x86/amd-iommu: Use get_device_id and check_device where appropriate
x86/amd-iommu: Move find_protection_domain to helper functions
x86/amd-iommu: Simplify get_device_resources()
x86/amd-iommu: Let domain_for_device handle aliases
x86/amd-iommu: Remove iommu specific handling from dma_ops path
x86/amd-iommu: Remove iommu parameter from __(un)map_single
x86/amd-iommu: Make alloc_new_range aware of multiple IOMMUs
...
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-nmw: (31 commits)
GFS2: Fix glock refcount issues
writeback: remove unused nonblocking and congestion checks (gfs2)
GFS2: drop rindex glock to refresh rindex list
GFS2: Tag all metadata with jid
GFS2: Locking order fix in gfs2_check_blk_state
GFS2: Remove dirent_first() function
GFS2: Display nobarrier option in /proc/mounts
GFS2: add barrier/nobarrier mount options
GFS2: remove division from new statfs code
GFS2: Improve statfs and quota usability
GFS2: Use dquot_send_warning()
VFS: Export dquot_send_warning
GFS2: Add set_xquota support
GFS2: Add get_xquota support
GFS2: Clean up gfs2_adjust_quota() and do_glock()
GFS2: Remove constant argument from qd_get()
GFS2: Remove constant argument from qdsb_get()
GFS2: Add proper error reporting to quota sync via sysfs
GFS2: Add get_xstate quota function
GFS2: Remove obsolete code in quota.c
...
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (30 commits)
TOMOYO: Add recursive directory matching operator support.
remove CONFIG_SECURITY_FILE_CAPABILITIES compile option
SELinux: print denials for buggy kernel with unknown perms
Silence the existing API for capability version compatibility check.
LSM: Move security_path_chmod()/security_path_chown() to after mutex_lock().
SELinux: header generation may hit infinite loop
selinux: Fix warnings
security: report the module name to security_module_request
Config option to set a default LSM
sysctl: require CAP_SYS_RAWIO to set mmap_min_addr
tpm: autoload tpm_tis based on system PnP IDs
tpm_tis: TPM_STS_DATA_EXPECT workaround
define convenient securebits masks for prctl users (v2)
tpm: fix header for modular build
tomoyo: improve hash bucket dispersion
tpm add default function definitions
LSM: imbed ima calls in the security hooks
SELinux: add .gitignore files for dynamic classes
security: remove root_plug
SELinux: fix locking issue introduced with c6d3aaa4e3
...
