Since commit 4baadb9e05 ("ARM: shmobile: r8a7778: remove obsolete
setup code"), Renesas R-Car SoCs are only supported in generic DT-only
ARM multi-platform builds. The driver doesn't need to use platform data
anymore, hence remove platform data configuration.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[wsa: removed now unused ret value and cast to proper enum type]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Enable the I2C core for this SoC. It is compitable to Gen2 SoCs, so
reuse the settings.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Enable the I2C core for this SoC. I add a new type because this version
has new features (e.g. DMA) which will be added somewhen later.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This allows using OpenCores I2C controller attached to its host in
native-endian mode with bi-endian CPUs. Example of such system is Xtensa
XTFPGA platform.
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-au1550 driver has to program various setup and hold times
for the sda/scl signals by hand. The current values seem to be
working best when the driver is supplied with 50MHz, however on the
DB1300 board 48MHz is the closest we can get to it, and the timings
are a bit too tight for that, leading to the last bit of a transmission
sometimes being swallowed. This manifests itself in wrong readings
of the ne1619 sensor and inability to configure the wm8731 i2s codec.
With the relaxed timings, both the sensor and the i2s codec can now
be accessed more reliably over a wider range of I2C block input
frequencies.
Verified on DB1200, DB1300 and DB1550 boards.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This code is repeated in probe:
i2c_dev->adapter.algo = &tegra_i2c_algo;
Cc: Donglin Peng <pengdonglin137@163.com>
Signed-off-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
According to "KeyStone Architecture Inter-IC Control Bus User Guide", fixed
additive part of frequency divisors (referred as "d" in the code and datasheet)
always equals to 6, independent of module clock prescaler.
module clock frequency
master clock frequency = ----------------------
(ICCL + 6) + (ICCH + 6)
It was not the case with original Davinci IP. Introduce new compatible property
"ti,keystone-i2c", which triggers special handling in the driver.
Without this change Keystone-based systems (having 204.8MHz input clock) choose
prescaler 29 (PSC=28). Using d=5 in this case leads to bus bitrate ~353kHz
instead of requested 400kHz. After correction, assuming d=6 bus rate is ~392kHz.
This gives ~11% transfer rate increase.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Hemanth Guruva Reddy <hemanth.guruva_reddy@nokia.com>
Tested-by: Lukasz Gemborowski <lukasz.gemborowski@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Issue the warning in all error paths when unable to register MSI or its
handler.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Propagate actual return code when requesting interrupt fails.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
struct pci_dev already has a flag to track if MSI is enabled or not. Use it
directly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is no need to repeat the work that is already done in the PCI driver
core. Remove suspend and resume callbacks.
Note that there is no more calls performed to enable or disable a PCI
device during suspend-resume cycle. Nowadays they seems to be
superfluous. Someone can read more in [1].
[1] https://www.kernel.org/doc/ols/2009/ols2009-pages-319-330.pdf
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
pcim_release() will release any requested region. There is no need to duplicate
this effort in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The way we currently scan I2C devices behind an I2C host controller does not
work in cases where the I2C device in question is not declared directly below
the host controller ACPI node.
This is perfectly legal according the ACPI 6.0 specification and some existing
systems are doing this.
To be able to enumerate all devices which are connected to a certain I2C host
controller we need to rework the current I2C scanning routine a bit. Instead of
scanning directly below the host controller we scan the whole ACPI namespace
for present devices with valid I2cSerialBus() connection pointing to the host
controller in question.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Dustin Byford <dustin@cumulusnetworks.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is some code duplication in i2c-designware-platdrv and
i2c-designware-pcidrv probe functions. What is even worse that duplication
requires i2c_dw_xfer(), i2c_dw_func() and i2c_dw_isr() i2c-designware-core
functions to be exported.
Therefore move common code into new i2c_dw_probe() and make functions above
local to i2c-designware-core.
While merging the code patch does following functional changes:
- I2C Adapter name will be "Synopsys DesignWare I2C adapter". Previously it
was used for platform and ACPI devices but PCI device used
"i2c-designware-pci".
- Using device name for interrupt name. Previous it was platform device name,
ACPI device name or "i2c-designware-pci".
- Error code from devm_request_irq() and i2c_add_numbered_adapter() will be
printed in case of error.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make it easier to distinguish between i2c-designware-platdrv and
i2c-designware-core functions and to be consistent with
i2c-designware-pcidrv.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
dw_readl() and dw_writel() are not used outside of i2c-designware-core and
they are not exported so make them static and remove their forward
declaration.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c_dw_is_enabled() became unused by the commit be58eda775
("i2c: designware-pci: Cleanup driver power management") and
i2c_dw_enable() by the commit 3a48d1c08f ("i2c: prevent spurious
interrupt on Designware controllers").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Device must not generate interrupts before registering the interrupt
handler so move i2c_dw_disable_int() before requesting it.
There are no known issues with this. The code has been here since commit
fe20ff5c7e ("i2c-designware: Add support for Designware core behind PCI
devices.").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is no need to clear interrupts in i2c_dw_pci_probe() since only place
where interrupts are unmasked is i2c_dw_xfer_init() and there interrupts
are always cleared after commit 2a2d95e9d6 ("i2c: designware: always
clear interrupts before enabling them").
This allows to cleanup the code and replace i2c_dw_clear_int() in
i2c_dw_xfer_init() by direct register read as there are no other callers.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The requested bit rate can be outside the range supported by the driver.
The maximum bit rate this driver supports at the moment is 400Khz.
If the requested bit rate is larger than the maximum supported by the
driver, set the bitrate to the maximum supported before bitrate_khz is
calculated.
Maximum speed supported by the driver can be increased to 1Mhz by
adding support for "fast plus mode" in the future.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Clear line status and all generated interrupts from the interrupt
status register before starting a transfer, as we may have
unserviced interrupts from previous transfers that might be
handled in the context of the new transfer.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c->line_status accumulates the line status bits that have been seen
with each interrupt. As we're only interested in that bit from the
current interrupt, refer to line_status (the argument to img_i2c_auto)
instead of i2c->line_status.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently, after determining the minimum value for the High period
(TCKH) the remainder of the internal clock pulses is set as the Low
period (TCKL). This causes the i2c clock duty cycle to be much less
than 50%.
Modify the starting position to TCKH and TCKL at 50% of the internal
clock, and adjusts the TCKH and TCKL values from there should the
minimum value for TCKL not be met. This results in duty cycles closer
to 50%.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Using % can be slow depending on the architecture.
Using DIV_ROUND_UP is nicer and more efficient way to do it.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move scb_wr_rd_fence to before reading from fifo and writing to
fifo to make sure the the first read/write is done after the required
number of cycles.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The code to read from the master read fifo, and write to the master
write fifo, checks a bit in an SCB register before every byte to
ensure that the fifo is not full (write fifo) or empty (read fifo).
Due to clock domain crossing inside the SCB block the updated value
of this bit is only visible after 2 cycles.
The scb_wr_rd_fence() function does 2 dummy writes (to the read-only
revision register), and it's called before reading from or writing to the
fifos to ensure that subsequent reads of the fifo status bits do not read
stale values.
As the 2 dummy writes are required in all versions of the ip, the version
check is dropped.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update the comments to match current behaviour. Shorten some comments.
Update copyrights.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If we don't clear START generation as soon as possible, it may cause
another message to be generated. To keep the race window as small as
possible, we clear it right at the beginning of the interrupt. We don't
need checking since we always want to stop START and STOP generation on
the next occasion after we started it.
This patch improves the situation but sadly does not completely fix it.
It is still to be researched if we can do better given this HW design.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Due to broken HW design, master IRQs are more timing critical, so give
them precedence over slave IRQ.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The manual says (55.4.8.6) that HW does automatically send STOP after
NACK was received. My measuerments confirm that.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Setting up new messages was done in process context while handling a
message was in interrupt context. Because of the HW design, this IP core
is sensitive to timing, so the context switches were too expensive. Move
this setup to interrupt context as well.
In my test setup, this fixed the occasional 'data byte sent twice' issue
which a number of people have seen. It also fixes to send REP_START
after a read message which was wrongly send as a STOP + START sequence
before.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We make sure to reinit the HW in the timeout case; then we know that
interrupts are always disabled in the sections protected by the
spinlock. Thus, we can simply remove it which is a preparation for
further refactoring. While here, rename the timeout variable to
time_left which is way more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We don't need to init HW before every transfer since we know the HW
state then. HW init at probe time is enough. While here, add setting the
clock register which belongs to init HW. Also, set MDBS bit since not
setting it is prohibited according to the manual.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull strscpy string copy function implementation from Chris Metcalf.
Chris sent this during the merge window, but I waffled back and forth on
the pull request, which is why it's going in only now.
The new "strscpy()" function is definitely easier to use and more secure
than either strncpy() or strlcpy(), both of which are horrible nasty
interfaces that have serious and irredeemable problems.
strncpy() has a useless return value, and doesn't NUL-terminate an
overlong result. To make matters worse, it pads a short result with
zeroes, which is a performance disaster if you have big buffers.
strlcpy(), by contrast, is a mis-designed "fix" for strlcpy(), lacking
the insane NUL padding, but having a differently broken return value
which returns the original length of the source string. Which means
that it will read characters past the count from the source buffer, and
you have to trust the source to be properly terminated. It also makes
error handling fragile, since the test for overflow is unnecessarily
subtle.
strscpy() avoids both these problems, guaranteeing the NUL termination
(but not excessive padding) if the destination size wasn't zero, and
making the overflow condition very obvious by returning -E2BIG. It also
doesn't read past the size of the source, and can thus be used for
untrusted source data too.
So why did I waffle about this for so long?
Every time we introduce a new-and-improved interface, people start doing
these interminable series of trivial conversion patches.
And every time that happens, somebody does some silly mistake, and the
conversion patch to the improved interface actually makes things worse.
Because the patch is mindnumbing and trivial, nobody has the attention
span to look at it carefully, and it's usually done over large swatches
of source code which means that not every conversion gets tested.
So I'm pulling the strscpy() support because it *is* a better interface.
But I will refuse to pull mindless conversion patches. Use this in
places where it makes sense, but don't do trivial patches to fix things
that aren't actually known to be broken.
* 'strscpy' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: use global strscpy() rather than private copy
string: provide strscpy()
Make asm/word-at-a-time.h available on all architectures
Two tagged for -stable
One is really a cleanup to match and improve kmemcache interface.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=yqg5
-----END PGP SIGNATURE-----
Merge tag 'md/4.3-fixes' of git://neil.brown.name/md
Pull md fixes from Neil Brown:
"Assorted fixes for md in 4.3-rc.
Two tagged for -stable, and one is really a cleanup to match and
improve kmemcache interface.
* tag 'md/4.3-fixes' of git://neil.brown.name/md:
md/bitmap: don't pass -1 to bitmap_storage_alloc.
md/raid1: Avoid raid1 resync getting stuck
md: drop null test before destroy functions
md: clear CHANGE_PENDING in readonly array
md/raid0: apply base queue limits *before* disk_stack_limits
md/raid5: don't index beyond end of array in need_this_block().
raid5: update analysis state for failed stripe
md: wait for pending superblock updates before switching to read-only
Pull MIPS updates from Ralf Baechle:
"This week's round of MIPS fixes:
- Fix JZ4740 build
- Fix fallback to GFP_DMA
- FP seccomp in case of ENOSYS
- Fix bootmem panic
- A number of FP and CPS fixes
- Wire up new syscalls
- Make sure BPF assembler objects can properly be disassembled
- Fix BPF assembler code for MIPS I"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: scall: Always run the seccomp syscall filters
MIPS: Octeon: Fix kernel panic on startup from memory corruption
MIPS: Fix R2300 FP context switch handling
MIPS: Fix octeon FP context switch handling
MIPS: BPF: Fix load delay slots.
MIPS: BPF: Do all exports of symbols with FEXPORT().
MIPS: Fix the build on jz4740 after removing the custom gpio.h
MIPS: CPS: #ifdef on CONFIG_MIPS_MT_SMP rather than CONFIG_MIPS_MT
MIPS: CPS: Don't include MT code in non-MT kernels.
MIPS: CPS: Stop dangling delay slot from has_mt.
MIPS: dma-default: Fix 32-bit fall back to GFP_DMA
MIPS: Wire up userfaultfd and membarrier syscalls.
Pull irq fixes from Thomas Gleixner:
"This update contains:
- Fix for a long standing race affecting /proc/irq/NNN
- One line fix for ARM GICV3-ITS counting the wrong data
- Warning silencing in ARM GICV3-ITS. Another GCC trying to be
overly clever issue"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Count additional LPIs for the aliased devices
irqchip/gic-v3-its: Silence warning when its_lpi_alloc_chunks gets inlined
genirq: Fix race in register_irq_proc()
The MIPS syscall handler code used to return -ENOSYS on invalid
syscalls. Whilst this is expected, it caused problems for seccomp
filters because the said filters never had the change to run since
the code returned -ENOSYS before triggering them. This caused
problems on the chromium testsuite for filters looking for invalid
syscalls. This has now changed and the seccomp filters are always
run even if the syscall is invalid. We return -ENOSYS once we
return from the seccomp filters. Moreover, similar codepaths have
been merged in the process which simplifies somewhat the overall
syscall code.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11236/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull x86 fixes from Ingo Molnar:
"Fixes all around the map: W+X kernel mapping fix, WCHAN fixes, two
build failure fixes for corner case configs, x32 header fix and a
speling fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/headers/uapi: Fix __BITS_PER_LONG value for x32 builds
x86/mm: Set NX on gap between __ex_table and rodata
x86/kexec: Fix kexec crash in syscall kexec_file_load()
x86/process: Unify 32bit and 64bit implementations of get_wchan()
x86/process: Add proper bound checks in 64bit get_wchan()
x86, efi, kasan: Fix build failure on !KASAN && KMEMCHECK=y kernels
x86/hyperv: Fix the build in the !CONFIG_KEXEC_CORE case
x86/cpufeatures: Correct spelling of the HWP_NOTIFY flag
Pull EFI fixes from Ingo Molnar:
"Two EFI fixes: one for x86, one for ARM, fixing a boot crash bug that
can trigger under newer EFI firmware"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
arm64/efi: Fix boot crash by not padding between EFI_MEMORY_RUNTIME regions
x86/efi: Fix boot crash by mapping EFI memmap entries bottom-up at runtime, instead of top-down
Pull drm fixes from Dave Airlie:
"Bunch of fixes all over the place, all pretty small: amdgpu, i915,
exynos, one qxl and one vmwgfx.
There is also a bunch of mst fixes, I left some cleanups in the series
as I didn't think it was worth splitting up the tested series"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (37 commits)
drm/dp/mst: add some defines for logical/physical ports
drm/dp/mst: drop cancel work sync in the mstb destroy path (v2)
drm/dp/mst: split connector registration into two parts (v2)
drm/dp/mst: update the link_address_sent before sending the link address (v3)
drm/dp/mst: fixup handling hotplug on port removal.
drm/dp/mst: don't pass port into the path builder function
drm/radeon: drop radeon_fb_helper_set_par
drm: handle cursor_set2 in restore_fbdev_mode
drm/exynos: Staticize local function in exynos_drm_gem.c
drm/exynos: fimd: actually disable dp clock
drm/exynos: dp: remove suspend/resume functions
drm/qxl: recreate the primary surface when the bo is not primary
drm/amdgpu: only print meaningful VM faults
drm/amdgpu/cgs: remove import_gpu_mem
drm/i915: Call non-locking version of drm_kms_helper_poll_enable(), v2
drm: Add a non-locking version of drm_kms_helper_poll_enable(), v2
drm/vmwgfx: Fix a command submission hang regression
drm/exynos: remove unused mode_fixup() code
drm/exynos: remove decon_mode_fixup()
drm/exynos: remove fimd_mode_fixup()
...
Pull input layer fixes from Dmitry Torokhov:
"Fixes for two recent regressions (in Synaptics PS/2 and uinput
drivers) and some more driver fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics - fix handling of disabling gesture mode"
Input: psmouse - fix data race in __ps2_command
Input: elan_i2c - add all valid ic type for i2c/smbus
Input: zhenhua - ensure we have BITREVERSE
Input: omap4-keypad - fix memory leak
Input: serio - fix blocking of parport
Input: uinput - fix crash when using ABS events
Input: elan_i2c - expand maximum product_id form 0xFF to 0xFFFF
Input: elan_i2c - add ic type 0x03
Input: elan_i2c - don't require known iap version
Input: imx6ul_tsc - fix controller name
Input: imx6ul_tsc - use the preferred method for kzalloc()
Input: imx6ul_tsc - check for negative return value
Input: imx6ul_tsc - propagate the errors
Input: walkera0701 - fix abs() calculations on 64 bit values
Input: mms114 - remove unneded semicolons
Input: pm8941-pwrkey - remove unneded semicolon
Input: fix typo in MT documentation
Input: cyapa - fix address of Gen3 devices in device tree documentation
This patch fixes one cases where abs() was being used with 64-bit
nanosecond values, where the result may be capped at 32-bits.
This potentially could cause watchdog false negatives on 32-bit
systems, so this patch addresses the issue by using abs64().
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1442279124-7309-2-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
inadvertently changing a huge pmd page into a pmd table entry.
- Function graph tracer panic fix caused by the return_to_handler code
corrupting the multi-regs function return value (composite types).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=AJCF
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Fix for transparent huge page change_protection() logic which was
inadvertently changing a huge pmd page into a pmd table entry.
- Function graph tracer panic fix caused by the return_to_handler code
corrupting the multi-regs function return value (composite types).
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: ftrace: fix function_graph tracer panic
arm64: Fix THP protection change logic
Pull m68k updates from Geert Uytterhoeven:
"Summary:
- Fix for accidental modification of arguments of syscall functions
- Wire up new syscalls
- Update defconfigs"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/defconfig: Update defconfigs for v4.3-rc1
m68k: Define asmlinkage_protect
m68k: Wire up membarrier
m68k: Wire up userfaultfd
m68k: Wire up direct socket calls
