This requests the status GPIO with initial input setup. It is required
to read the GPIO status at probe time and thus correctly avoid sending
I2C messages when AC is not plugged.
When requesting the GPIO without initial input setup, it always reads 0
which causes probe to fail as it assumes the charger is connected, sends
I2C messages and fails.
While at it, this switches the driver over to gpiod API.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Switch to using new gpio_desc interface and devm gpio get calls to
automatically manage gpio resource. Use gpiod_get_value which handles
active high / low calls.
If gpio_detect is set then force loading of the driver as it is
reasonable to assume that the battery may not be present.
Update the is_present flag immediately in the IRQ.
Remove legacy gpio specification from platform data.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add the power supply's current max property,
POWER_SUPPLY_PROP_CURRENT_MAX.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add the power supply capacity level property, it corresponds to
POWER_SUPPLY_CAPACITY_LEVEL_*.
It also utilizes the precision voltage detector function module
to catch the low battery voltage.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The power supply type property is varying as the external power
supply changes. It is not a constant.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add the charger status change interrupt support, it will report
the power supply changed event.
This interrupt is generated by one of the conditions as below:
- the state machine jumps out of or into the EOC state
- the CHGIN input voltage goes out of or into the valid range.
- the battery temperature goes out of or into the valid range.
- the PRECHARGE time-out occurs.
- the total charge time-out occurs.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
When get the property, first check the charger state machine,
then check the status bit to decide what value is assigned to
the corresponding property.
Retain the SUSCHG bit of REG 0x71 when configure the timers to
avoid losting the charger suspending info after boot.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Remove "battery_temperature" member, it is redundant, it is the
hardware's responsibility to handle TH pin properly.
It is unnecessary to use the dt property to check if there is
a battery temperature monitor or not.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Since the act8945a_charger is regarded as a sub-device, all properties will
be assigned to its own device node. All properties can be achieved from its
own node, instead of from its parent device.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
When the charger is missing (disconnected), it is safe to assume that
the charger chip is no charging.
This is especially relevant when a status GPIO is present and the
charger is getting disconnected. bq24735_charger_is_charging will be
triggered due to the interrupt then, it will attempt to read whether it
is charging through i2c, which will fail as the charger is disconnected.
This also fixes that specific issue.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Change my email address to kernel.org instead of Samsung one for the
purpose of any future contact. The copyrights remain untouched and are
attributed to Samsung.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
alloc_ordered_workqueue() with WQ_MEM_RECLAIM set replaces
deprecated create_singlethread_workqueue(). This is the identity
conversion.
The workqueue "monitor_wqueue" is used to monitor the battery
status. It has been identity converted.
It queues multiple work items viz &di->monitor_work,
&di->set_charged_work, which require execution ordering.
Hence, alloc_workqueue has been used to replace the
deprecated create_singlethread_workqueue instance.
WQ_MEM_RECLAIM flag has been set to ensure forward progress under
memory pressure.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
alloc_ordered_workqueue() with WQ_MEM_RECLAIM set replaces
deprecated create_singlethread_workqueue(). This is the identity
conversion.
The workqueue "fg_wq" is used for running the FG algorithm periodically.
It has been identity converted.
It has multiple work items viz fg_periodic_work, fg_low_bat_work,
fg_reinit_work, fg_work, fg_acc_cur_work and fg_check_hw_failure_work,
which require execution ordering. Hence, a dedicated ordered workqueue
has been used here.
The WQ_MEM_RECLAIM flag has been set to guarantee forward progress under
memory pressure.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The workqueue "wq" is used for handling battery related tasks.
It has a single work item viz &mb->update and hence it doesn't require
execution ordering. Hence, alloc_workqueue has been used to replace the
deprecated create_singlethread_workqueue instance.
The WQ_MEM_RECLAIM flag has been set to ensure forward progress under
memory pressure.
Since there is a single work item, explicit concurrency
limit is unnecessary here.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
alloc_ordered_workqueue() with WQ_MEM_RECLAIM set replaces
deprecated create_singlethread_workqueue(). This is the identity
conversion.
The workqueue "charger_wq" is used for the IRQs and checking HW state of
the charger. It has been identity converted.
It has multiple work items viz usb_charger_attached_work, kick_wd_work,
check_vbat_work, check_hw_failure_work, usb_charger_attached_work,
ac_work, ac_charger_attached_work, attach_work and check_usbchgnotok_work,
which require execution ordering. Hence, a dedicated ordered workqueue
has been used here.
The WQ_MEM_RECLAIM flag has also been set to ensure
forward progress under memory pressure.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The workqueue "monitor_wqueue" is used to monitor the PMIC battery status.
It queues a single work item (pbi->monitor_battery) and hence doesn't
require ordering. Hence, alloc_workqueue has been used to replace the
deprecated create_singlethread_workqueue instance.
Since PMIC battery status needs to be monitored for any change, the
WQ_MEM_RECLAIM flag has been set to ensure forward progress under memory
pressure.
Since there is a single work item, explicit concurrency
limit is unnecessary here.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
alloc_ordered_workqueue() with WQ_MEM_RECLAIM set replaces
deprecated create_singlethread_workqueue(). This is the identity
conversion.
The workqueue "charger_wq" is used for running all the charger related
tasks. This involves charger detection, checking for HW failure and HW
status. This workqueue has been identity converted.
It queues multiple workitems viz &pm2->check_main_thermal_prot_work,
&pm2->check_hw_failure_work, &pm2->ac_work. Hence, the deprecated
create_singlethread_workqueue() instance has been replaced with a
dedicated ordered workqueue.
The WQ_MEM_RECLAIM flag has been set to ensure forward progress under
memory pressure.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The workqueue "btemp_wq" is used for measuring the temperature
periodically. It queues a single workitem (btemp_periodic_work) and
hence doesn't require ordering. Thus, the deprecated
create_singlethread_workqueue() instance has been replaced with
alloc_workqueue().
The WQ_MEM_RECLAIM flag has been set to ensure forward progress under
memory pressure.
Since there is a single work item, explicit concurrency
limit is unnecessary here.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
alloc_ordered_workqueue() with WQ_MEM_RECLAIM set replaces
deprecated create_singlethread_workqueue(). This is the identity
conversion.
The workqueue "chargalg_wq" is used for running the charging algorithm.
It has multiple workitems viz &di->chargalg_periodic_work,
&di->chargalg_wd_work, &di->chargalg_work per abx500_chargalg, which
require ordering. It has been identity converted.
Also, WQ_MEM_RECLAIM has been set to ensure forward progress under
memory pressure.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Remove .owner field if calls are used which set it automatically.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use the managed resource version of reboot_mode_register().
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Provide managed resource version of reboot_mode_register() and
reboot_mode_unregister() to simplify implementations.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Battery capacity level is a standard feature of sbs battery
That can be used to tell what the remainig battery capacity is, and
can tell if the battery has not been calibrated/initialized, which makes
the capacity and charging/discharging percentages invalid.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add missing platform_set_drvdata() in tps65217_charger_probe(), otherwise
calling platform_get_drvdata() in remove returns NULL.
This is detected by Coccinelle semantic patch.
Fixes: 3636859b28 ("power_supply: Add support for tps65217-charger")
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use devm_power_supply_register instead of power_supply_register.
Remove call to power_supply_unregister.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Currently the battery detect gpio can not be used with a chained interrupt
controller that requires threaded irq handlers. Use threaded irq instead.
In addition this was not going to be working at present because
chip->power_supply is assigned after the request irq call.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use devm_kzalloc to allow memory to be freed automatically on
driver probe failure or removal.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The bq27000 and bq27010 have a single byte FLAGS register.
Other gauges have 16 bit FLAGS registers.
For reading the FLAGS register it is sufficient to read the single
register instead of reading RSOC at the next higher address as
well and then ignore the high byte.
This does not change functionality but optimizes i2c and hdq
traffic.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Make use of IRQ resources defined in tps65217 mfd code. If they are valid
we use them instead separate poll task, in order to define AC power state.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
commit 4fcd504edb ("power: reset: add reboot mode driver") uses api from
syscon, and syscon uses ioremap/iounmap which depends on HAS_IOMEM, so
let's depend on MFD_SYSCON instead of selecting it directly to avoid the
um-allyesconfig like build error on archs that without iomem:
drivers/mfd/syscon.c: In function 'of_syscon_register':
drivers/mfd/syscon.c:67:9: error: implicit declaration of function 'ioremap' [-Werror=implicit-function-declaration]
base = ioremap(res.start, resource_size(&res));
^
drivers/mfd/syscon.c:67:7: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
base = ioremap(res.start, resource_size(&res));
^
drivers/mfd/syscon.c:109:2: error: implicit declaration of function 'iounmap' [-Werror=implicit-function-declaration]
iounmap(base);
^
Reported-by: Kbuild test robot <fengguang.wu@intel.com>
Fixes: 4fcd504edbf7("power: reset: add reboot mode driver")
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The device's model download function returns the model data as
an array of u32s, which is later compared to the reference
model data. However, since the latter is an array of u16s,
the comparison does not happen correctly, and model verification
fails. This in turn breaks the POR initialization sequence.
Fixes: 39e7213edc ("max17042_battery: Support regmap to access device's registers")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sven Van Asbroeck <TheSven73@googlemail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This moves all power supply drivers from drivers/power/
to drivers/power/supply/. The intention is a cleaner
source tree, since drivers/power/ also contains frameworks
unrelated to power supply, like adaptive voltage scaling.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we merge
through arm-soc for historical reasons, is also sizable this time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=O8+y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we
merge through arm-soc for historical reasons, is also sizable this
time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
soc: raspberrypi-power: add CONFIG_OF dependency
firmware: scpi: add CONFIG_OF dependency
video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
serial: clps711x: Changing the compatibility string to match with the smallest supported chip
irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
clk: clps711x: Changing the compatibility string to match with the smallest supported chip
...
The cleanup branch keeps going down in size as we've completed a lot of
the major legacy platform removals and conversions.
A handful of changes this time around, some of the themes or larger sets are:
- A bunch of i.MX cleanups around platform detection, init call cleanups
- Misc fixes of missing/implicit includes
- Removal of ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SfR/
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"The cleanup branch keeps going down in size as we've completed a lot
of the major legacy platform removals and conversions.
A handful of changes this time around, some of the themes or larger
sets are:
- A bunch of i.MX cleanups around platform detection, init call cleanups
- Misc fixes of missing/implicit includes
- Removal of ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (40 commits)
ARM: mps2: fix typo
ARM: s3c64xx: avoid warning about 'struct device_node'
bus: mvebu-mbus: make mvebu_mbus_syscore_ops static
bus: mvebu-mbus: fix __iomem on register pointers
ARM: tegra: Remove board_init_funcs array
ARM: iop: Fix indentation
ARM: imx: remove cpu_is_mx*()
ARM: imx: remove last call to cpu_is_mx5*
ARM: imx: rework mx27_pm_init() call
ARM: imx: deconstruct mx3_idle
ARM: imx: deconstruct mxc_rnga initialization
ARM: imx: remove cpu_is_mx1 check
ARM: i.MX: Do not explicitly call l2x0_of_init()
ARM: i.MX: system.c: Tweak prefetch settings for performance
ARM: i.MX: system.c: Replace magic numbers
ARM: i.MX: system.c: Remove redundant errata 752271 code
ARM: i.MX: system.c: Convert goto to if statement
ARM: Kirkwood: fix kirkwood_pm_init() declaration/type
ARM: Kirkwood: make kirkwood_disable_mbus_error_propagation() static
ARM: orion5x: make orion5x_legacy_handle_irq static
...
* introduce reboot mode driver
* add DT support to max8903
* add power supply support for axp221
* misc. fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bMvA
-----END PGP SIGNATURE-----
Merge tag 'for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
- introduce reboot mode driver
- add DT support to max8903
- add power supply support for axp221
- misc fixes
* tag 'for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
power: reset: add reboot mode driver
dt-bindings: power: reset: add document for reboot-mode driver
power_supply: fix return value of get_property
power: qcom_smbb: Make an extcon for usb cable detection
max8903: adds support for initiation via device tree
max8903: adds documentation for device tree bindings.
max8903: remove unnecessary 'out of memory' error message.
max8903: removes non zero validity checks on gpios.
max8903: adds requesting of gpios.
max8903: cleans up confusing relationship between dc_valid, dok and dcm.
max8903: store pointer to pdata instead of copying it.
power_supply: bq27xxx_battery: Group register mappings into one table
docs: Move brcm,bcm21664-resetmgr.txt
power/reset: make syscon_poweroff() static
power: axp20x_usb: Add support for usb power-supply on axp22x pmics
power_supply: bq27xxx_battery: Index register numbers by enum
power_supply: bq27xxx_battery: Fix copy/paste error in header comment
MAINTAINERS: Add file patterns for power supply device tree bindings
power: reset: keystone: Enable COMPILE_TEST
Pull timer updates from Thomas Gleixner:
"This update provides the following changes:
- The rework of the timer wheel which addresses the shortcomings of
the current wheel (cascading, slow search for next expiring timer,
etc). That's the first major change of the wheel in almost 20
years since Finn implemted it.
- A large overhaul of the clocksource drivers init functions to
consolidate the Device Tree initialization
- Some more Y2038 updates
- A capability fix for timerfd
- Yet another clock chip driver
- The usual pile of updates, comment improvements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (130 commits)
tick/nohz: Optimize nohz idle enter
clockevents: Make clockevents_subsys static
clocksource/drivers/time-armada-370-xp: Fix return value check
timers: Implement optimization for same expiry time in mod_timer()
timers: Split out index calculation
timers: Only wake softirq if necessary
timers: Forward the wheel clock whenever possible
timers/nohz: Remove pointless tick_nohz_kick_tick() function
timers: Optimize collect_expired_timers() for NOHZ
timers: Move __run_timers() function
timers: Remove set_timer_slack() leftovers
timers: Switch to a non-cascading wheel
timers: Reduce the CPU index space to 256k
timers: Give a few structs and members proper names
hlist: Add hlist_is_singular_node() helper
signals: Use hrtimer for sigtimedwait()
timers: Remove the deprecated mod_timer_pinned() API
timers, net/ipv4/inet: Initialize connection request timers as pinned
timers, drivers/tty/mips_ejtag: Initialize the poll timer as pinned
timers, drivers/tty/metag_da: Initialize the poll timer as pinned
...
Here's the big USB driver update for 4.8-rc1. Lots of the normal stuff
in here, musb, gadget, xhci, and other updates and fixes. All of the
details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iFYEABECABYFAleVPioPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspB5AAnj7a
VJ2t2kcWzFUNQ6dyJrJCGGRAAKDZmb5CnOGeqJmdVpDzN1CGLYjfiw==
=47iA
-----END PGP SIGNATURE-----
Merge tag 'usb-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big USB driver update for 4.8-rc1. Lots of the normal
stuff in here, musb, gadget, xhci, and other updates and fixes. All
of the details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
cdc-acm: beautify probe()
cdc-wdm: use the common CDC parser
cdc-acm: cleanup error handling
cdc-acm: use the common parser
usbnet: move the CDC parser into USB core
usb: musb: sunxi: Simplify dr_mode handling
usb: musb: sunxi: make unexported symbols static
usb: musb: cppi41: add dma channel tracepoints
usb: musb: cppi41: move struct cppi41_dma_channel to header
usb: musb: cleanup cppi_dma header
usb: musb: gadget: add usb-request tracepoints
usb: musb: host: add urb tracepoints
usb: musb: add tracepoints to dump interrupt events
usb: musb: add tracepoints for register access
usb: musb: dsps: use musb register read/write wrappers instead
usb: musb: switch dev_dbg to tracepoints
usb: musb: add tracepoints support for debugging
usb: quirks: Add no-lpm quirk for Elan
phy: rcar-gen3-usb2: fix mutex_lock calling in interrupt
phy: rockhip-usb: use devm_add_action_or_reset()
...
Here is the big char/misc driver update for 4.8-rc1.
Not a lot of stuff, but it's all over the place, full details are in the
shortlog below. All of these have been in linux-next with no reported
issues for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iFYEABECABYFAleVPBsPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspEQgAoJOX
nSWKA7j4JMGy1v+uNIqsgUmUAJsFyS388N+Faa2K4uyp7CYQ6jaAZw==
=0Ofd
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc driver update for 4.8-rc1.
Not a lot of stuff, but it's all over the place, full details are in
the shortlog. All of these have been in linux-next with no reported
issues for a while"
* tag 'char-misc-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (49 commits)
lkdtm: silence warnings about function declarations
lkdtm: hide unused functions
intel_th: pci: Add Kaby Lake PCH-H support
intel_th: Fix a deadlock in modprobing
dsp56k: prevent a harmless underflow
chardev: add missing line break in pr_warn
lkdtm: use struct arrays instead of enums
lkdtm: move jprobe entry points to start of source
lkdtm: reorganize module paramaters
lkdtm: rename globals for clarity
lkdtm: rename "count" to "crash_count"
lkdtm: remove intentional off-by-one array access
lkdtm: split remaining logic bug tests to separate file
lkdtm: split heap corruption tests to separate file
lkdtm: split memory permissions tests to separate file
lkdtm: split usercopy tests to separate file
lkdtm: drop "alloc_size" parameter
lkdtm: add usercopy test for blocking kernel text
extcon: adc-jack: add suspend/resume support
extcon: add missing of_node_put after calling of_parse_phandle
...
We now have implicit batching in the timer wheel. The slack API is no longer
used, so remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Chris Mason <clm@fb.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: George Spelvin <linux@sciencehorizons.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-block@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160704094342.189813118@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This driver parses the reboot commands like "reboot bootloader"
and "reboot recovery" to get a boot mode described in the
device tree , then call the write interfae to store the boot
mode in some place like special register or sram, which can
be read by the bootloader after system reboot, then the bootloader
can take different action according to the mode stored.
This is commonly used on Android based devices, in order to
reboot the device into fastboot or recovery mode.
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
Tested-by: John Stultz <john.stultz@linaro.org>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
power_supply_get_property() should ideally return -EAGAIN if it is
called while the power_supply is being registered. There was no way
previously to determine if use_cnt == 0 meant that the power_supply
wasn't fully registered yet, or if it had already been unregistered.
Add a new boolean to the power_supply struct to simply show if
registration is completed. Lastly, modify the check in
power_supply_show_property() to also ignore -EAGAIN when so it
doesn't complain about not returning the property.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
On these PMICs the usb cable connection/disconnection is
indicated by the usb-valid interrupt being high or low
respectively. Let's make an extcon for that, so we can notify usb
drivers of the cable state.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Adds support for device tree to setup a max8903 battery charger. DC and USB
validity are determined by looking the presence of the dok and uok gpios.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Remove the 'out of memory' error message as it is printed by the core.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Prior to this commit a zero gpio was treated as invalid. Whereas
gpio_is_valid() will treat a zero gpio as valid.
This commit removes the confusion and explicitly uses gpio_is_valid()
throughout. Which in turn results in several of the error messages becoming
redundant and thus removed.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
