Before 5b83b2234b the driver was hard coding the wakeup irq to
be active low. The generic pm wakeirq does not override the active
high/low parameter, hence it must be specified correctly in the
device tree.
Mind that SDIO IRQ is active low as defined in the SDIO specification
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The am335x can't detect pending cirq in PM runtime suspend.
This patch reconfigures dat1 as a GPIO before going to suspend.
SDIO interrupts are detected with the GPIO, the GPIO will only wake
the module from suspend, SDIO irq detection will still happen through the
IP block.
Idea of remuxing the pins by Tony Lindgren. Code contributions from
Tony Lindgren and Balaji T K <balajitk@ti.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There have been various patches floating around for enabling
the SDIO IRQ for hsmmc, but none of them ever got merged.
Probably the reason for not merging the SDIO interrupt patches
has been the lack of wake-up path for SDIO on some omaps that
has also needed remuxing the SDIO DAT1 line to a GPIO making
the patches complex.
This patch adds the minimal SDIO IRQ support to hsmmc for
omaps that do have the wake-up path. For those omaps, the
DAT1 line need to have the wake-up enable bit set, and the
wake-up interrupt is the same as for the MMC controller.
This patch has been tested on am3730 es1.2 with mwifiex
connected to MMC3 with mwifiex waking to Ethernet traffic
from off-idle mode. Note that for omaps that do not have
the SDIO wake-up path, this patch will not work for idle
modes and further patches for remuxing DAT1 to GPIO are
needed.
Based on earlier patches [1][2] by David Vrabel
<david.vrabel@csr.com>, Steve Sakoman <steve@sakoman.com>
For now, only support SDIO interrupt if we are booted with
a separate wake-irq configued via device tree. This is
because omaps need the wake-irq for idle states, and some
omaps need special quirks. And we don't want to add new
legacy mux platform init code callbacks any longer as we
are moving to DT based booting anyways.
To use it, you need to specify the wake-irq using the
interrupts-extended property.
[1] http://www.sakoman.com/cgi-bin/gitweb.cgi?p=linux.git;a=commitdiff_plain;h=010810d22f6f49ac03da4ba384969432e0320453
[2] http://comments.gmane.org/gmane.linux.kernel.mmc/20446
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When device is booted using devicetree, platforms impacted by Erratum
2.1.1.128 is not detected easily in the mmc driver. This erratum
indicates that the module cannot do multi-block transfers. Platforms
such as LDP which use OMAP3 ES revision prior to ES3.0 are impacted by
this.
Provide a new compatible property "ti,omap3-pre-es3-hsmmc" to allow
driver to determine if driver needs to implement quirks associated
with the specific module version (primarily because the IP revision
information is not sufficient for the same).
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <chris@printf.net>
Adds AM33XX MMC support for am335x-bone, am335x-evm and am335x-evmsk boards.
Also added is the DMA binding definitions based on the generic DMA request
binding.
Additional changes made to DTS:
* Interrupt, reg and compatible properties added
* ti,needs-special-hs-handling added
Signed-off-by: Matt Porter <mporter@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
HSMMC IP on AM33xx need a special setting to handle High-speed cards.
Other platforms like TI81xx, OMAP4 may need this as-well. This depends
on the HSMMC IP timing closure done for the high speed cards.
From AM335x TRM (SPRUH73F - 18.3.12 Output Signals Generation):
The MMC/SD/SDIO output signals can be driven on either falling edge or
rising edge depending on the SD_HCTL[2] HSPE bit. This feature allows
to reach better timing performance, and thus to increase data transfer
frequency.
There are few pre-requisites for enabling the HSPE bit
- Controller should support High-Speed-Enable Bit and
- Controller should not be using DDR Mode and
- Controller should advertise that it supports High Speed in
capabilities register and
- MMC/SD clock coming out of controller > 25MHz
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Now that we have common bindings for MMC, rewrite the individual
bindings to inherit from mmc.txt and describe their differences.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch unifies the current DT MMC bindings documentation and code,
adds generic MMC DT bindings documentation, and updates .dts files for
consistency.
[cjb: typo fixes, addition of max-frequency property]
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Define dt bindings for the ti-omap-hsmmc, and adapt the driver to extract
data (which was earlier passed as platform_data) from device tree.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
