This patch adds to support no_skb_reserve function to improve
performance for some platforms. About the detail, please refer to
the commit log of "quirk_avoids_skb_reserve" in
include/linux/usb/gadget.h.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds a flag "no_skb_reserve" in struct eth_dev.
So, if a peripheral driver sets the quirk_avoids_skb_reserve flag,
upper network gadget drivers (e.g. f_ncm.c) can avoid skb_reserve()
calling using the flag as well.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some platforms (e.g. USB-DMAC on R-Car SoCs) has memory alignment
restriction. If memory alignment is not match, the usb peripheral
driver decides not to use the DMA controller. Then, the performance
is not good.
In the case of u_ether.c, since it calls skb_reserve() in rx_submit(),
it is possible to cause memory alignment mismatch.
So, this patch adds a new quirk "quirk_avoids_skb_reserve" to avoid
skb_reserve() calling in u_ether.c to improve performance.
A peripheral driver will set this flag and network gadget drivers
(e.g. f_ncm.c) will reference the flag via gadget_avoids_skb_reserve().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
trivial typo fix in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds support for r8a7796 (R-Car M3-W).
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Memory allocated for goku_udc device is not deallocated at error
paths in goku_probe(), because gadget_release() destructor
is not registered yet.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Trivial fix to spelling mistakes in dev_err messages.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's perfectly fine to have all configfs functions
built-in while having modular legacy gadgets. Let's
allow for that.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case our TRB ring is full, we can avoid trying to
kick transfers which won't start and just add requests
to the queue.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use gadget's framework allocation function instead of directly calling
usb_ep_alloc_request().
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We should always use free_ep_req() when allocating requests with
alloc_ep_req().
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The default_length parameter of alloc_ep_req was not really necessary
and gadget drivers would almost always create an inline function to pass
the same value to len and default_len.
This patch removes that parameter and updates all calls to alloc_ep_req() to
use the new API.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
ENDXFER polling is available on version 3.10a and later of the
DWC_usb3 (USB 3.0) controller. With this feature, the software can poll
the CMDACT bit in the DEPCMD register after issuing an ENDXFER command.
This feature is enabled by writing GUCTL2[14].
This feature is NOT available on the DWC_usb31 (USB 3.1) IP.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The TX settings can be calibrated for particular hardware. The
phy is reset by Linux, so this cannot be handled by the bootloader.
The TRM mentions that the maximum resistance should be used for the
DN/DP calibration in order to pass USB certification.
The values for the TX registers are poorly described in the TRM.
The meanings of the register values were taken from another
NXP-provided document:
https://community.nxp.com/message/566147#comment-566912
Acked-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jaret Cantu <jaret.cantu@timesys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The dwc3 driver expicitly looks for "usb2-phy" or "usb3-phy", but we
never noted these names in the documentation.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add revision number constants for the 3.00a and 3.10a releases.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Introduces a new FunctionFS descriptor flag named
FUNCTIONFS_CONFIG0_SETUP.
When this flag is enabled, FunctionFS userspace drivers can process
non-standard control requests in configuration 0.
Signed-off-by: Felix Hädicke <felixhaedicke@web.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It can sometimes be necessary for gadget drivers to process non-standard
control requests, which host devices can send without having sent
USB_REQ_SET_CONFIGURATION.
Therefore, the req_match() usb_function method is enhanced with the new
parameter "config0". When a USB configuration is active, this parameter
is false. When a non-core control request is processed in
composite_setup(), without an active configuration, req_match() of the
USB functions of all available configurations which implement this
function, is called with config0=true. Then the control request gets
processed by the first usb_function instance whose req_match() returns
true.
Signed-off-by: Felix Hädicke <felixhaedicke@web.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Introduces a new FunctionFS descriptor flag named
FUNCTIONFS_ALL_CTRL_RECIP. When this flag is enabled, control requests,
which are not explicitly directed to an interface or endpoint, can be
handled.
This allows FunctionFS userspace drivers to process non-standard
control requests.
Signed-off-by: Felix Hädicke <felixhaedicke@web.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Even if the /dev/hidg* chardev is automatically created, one
has to guess which one belongs to which function. In the case
of multiple HID functions, or maybe even multiple peripherals,
this becomes difficult.
Add the dev (with major and minor number) to configfs to allow
looking up (or even creating) the right device node for each
function. This file is read-only.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When dwc3 core enters into suspend mode, the system (especially for mobile
device) may power off the dwc3 controller for power saving, that will cause
dwc3 controller lost the mode operation when resuming dwc3 core.
Thus we can move the mode setting into dwc3_core_init() function to avoid this
issue.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This change makes sure that the ALSA buffers are cleaned if an endpoint
becomes disabled.
Before this change, if the internal ALSA buffer did overflow, the MIDI
function would stop sending MIDI to the host.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This refactor results in a cleaner state machine code and promotes
consistency, readability, and maintanability of this driver.
This refactor state machine was well tested and it is currently running in
production code and devices.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
512 is the value used by wMaxPacketSize, as specified by the USB Spec. This
makes sure this driver uses, by default, the most optimal value for IN and OUT
endpoint requests.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The new version of alloc_ep_req() already aligns the buffer size to
wMaxPacketSize on OUT endpoints.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Using usb_ep_align() makes sure that the buffer size for OUT endpoints is
always aligned with wMaxPacketSize (512 usually). This makes sure
that no buffer has the wrong size, which can cause nasty bugs.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Length of buffers should be of type size_t whenever possible. Altough
recommended, this change has no real practical change, unless a driver has a
uses a huge or negative buffer size - it might help find these bugs.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
USB spec specifies wMaxPacketSize to be little endian (as other properties),
so when using this variable in the driver we should convert to the current
CPU endianness if necessary.
This patch also introduces usb_ep_align() which does always returns the
aligned buffer size for an endpoint. This is useful to be used by USB requests
allocator functions.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Introduce an attribute "inquiry_string" to the lun.
In some environments, e. g. BIOS boot menus, the inquiry string
is the only information about devices presented to the user. The
default string depends on the "cdrom" bit of the first lun as
well as the kernel version and allows no further customization.
So without access to the client it is not obvious which gadget is
active at a given point and what any of the available luns might
contain.
If "inquiry_string" is ignored or set to the empty string, the
old behavior is preserved.
Signed-off-by: Philipp Gesang <philipp.gesang@intra2net.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Rockchip platform merely enable usb3 clocks and
populate its children. So we can use this generic
glue layer to support Rockchip dwc3.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds the devicetree documentation required for Rockchip
USB3.0 core wrapper consisting of USB3.0 IP from Synopsys.
It supports DRD mode, and could operate in device mode (SS, HS, FS)
and host mode (SS, HS, FS, LS).
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a quirk to clear the GUSB3PIPECTL.DELAYP1TRANS bit,
which specifies whether disable delay PHY power change
from P0 to P1/P2/P3 when link state changing from U0
to U1/U2/U3 respectively.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Support to configure the UTMI+ PHY with an 8- or 16-bit
interface via DT. The UTMI+ PHY interface is a hardware
capability, and it's platform dependent. Normally, the
PHYIF can be configured during coreconsultant.
But for some specific USB cores(e.g. rk3399 SoC DWC3),
the default PHYIF configuration value is false, so we
need to reconfigure it by software.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a quirk to clear the GUSB2PHYCFG.U2_FREECLK_EXISTS bit,
which specifies whether the USB2.0 PHY provides a free-running
PHY clock, which is active when the clock control input is active.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
With composite gadget (ACM + NCM), USB3380 to host TCP transfer
speed dropped to 150 Mbit/s compared to 900 Mbit/s with NCM
gadget. Problem seems to be that net2280/USB3380 has only four
DMA channels and those DMA channels are allocated to first HW
endpoints. Endpoint match function was mapping endpoint names
directly, so NCM did not get DMA for bulk endpoints.
This patch changed match_ep to prefer DMA enabled hw endpoints
for bulk usb endpoints and PIO for interrupt usb endpoints.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@haltian.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
With SuperSpeed CDC NCM gadget, net2280 would get stuck in
'handle_ep_small' function. Triggering issue requires large
TCP transfer from host to USB3380.
Patch adds check for stuck condition and prevents hard lockup.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@haltian.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Patch enables SuperSpeed for NCM gadget.
Tested with USB3380 and measured TCP throughput with two Intel PCs:
udc to host: 920 Mbit/s
host to udc: 550 Mbit/s
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@haltian.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
alloc_ordered_workqueue replaces the deprecated
create_singlethread_workqueue.
There are multiple work items on the work queue, which require
ordering. Hence, an ordered workqueue has been used.
The workqueue "wq_otg" is not being used on a memory reclaim path.
Hence, WQ_MEM_RECLAIM has not been set.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The assignment ret = ret is redundant and can be removed.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Disabling USB gadget functions configured through configfs is something
that can happen in normal use cases. Keep the existing log for this type
of event, but only as information, not as an error.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As the last known user, ie. pxa27x_udc relying on calls to
usb_gadget_xxx() was amended to use the phy notifier, remove a bit the
USB stack adherence.
Actually the driver still uses the gadget API for structures definition,
but the implementation of USB gadget specific function usb_gadget_*() is
not necessary anymore.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In the gpio based case, the status of the phy is known at start by
reading the VBus gpio.
Actually, this is a fix, as this initial state, when not set up,
prevents a gadget to answer to the enumeration phase, as there is no
notification in this case (the VBus is already high when kernel boots)
so no interrupt is triggered, and the flow is :
- gadget initializes
- gadget gets its phy-generic with a xxx_get_phy_xxx() call type
- gadget does a "set_peripheral()" call type
=> here if the otg->state is correctly filled, the proper vbus
handling will be called, and the gadget will be aware it should
answer enumeration and go forth
Without this fix, the USB cable must be removed and replugged for any
gadget relying on phy-generic and its gpio vbus handling to work.
The problem was seen on a pxa27x architecture based board on a
devicetree build.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
