When marsheling a user path to the kernel struct ib_sa_path, need
to zero smac, dmac and set the vlan id to the "no vlan" value.
Fixes: dd5f03beb4 ("IB/core: Ethernet L2 attributes in verbs/cm structures")
Reported-by: Aleksey Senin <alekseys@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When device is being removed (e.g during VPI port link type change
from ETH to IB), tasks for gid table changes should not be executed.
Flush the current queue of tasks and block further tasks from entering the queue.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Chuck Lever reported the following stack trace:
=================================
[ INFO: inconsistent lock state ]
3.16.0-rc2-00024-g2e78883 #17 Tainted: G E
---------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
swapper/0/0 [HC0[0]:SC1[1]:HE1:SE0] takes:
(&(&iboe->lock)->rlock){+.?...}, at: [<ffffffffa065f68b>] mlx4_ib_addr_event+0xdb/0x1a0 [mlx4_ib]
{SOFTIRQ-ON-W} state was registered at:
[<ffffffff810b3110>] mark_irqflags+0x110/0x170
[<ffffffff810b4806>] __lock_acquire+0x2c6/0x5b0
[<ffffffff810b4bd9>] lock_acquire+0xe9/0x120
[<ffffffff815f7f6e>] _raw_spin_lock+0x3e/0x80
[<ffffffffa0661084>] mlx4_ib_scan_netdevs+0x34/0x260 [mlx4_ib]
[<ffffffffa06612db>] mlx4_ib_netdev_event+0x2b/0x40 [mlx4_ib]
[<ffffffff81522219>] register_netdevice_notifier+0x99/0x1e0
[<ffffffffa06626e3>] mlx4_ib_add+0x743/0xbc0 [mlx4_ib]
[<ffffffffa05ec168>] mlx4_add_device+0x48/0xa0 [mlx4_core]
[<ffffffffa05ec2c3>] mlx4_register_interface+0x73/0xb0 [mlx4_core]
[<ffffffffa05c505e>] cm_req_handler+0x13e/0x460 [ib_cm]
[<ffffffff810002e2>] do_one_initcall+0x112/0x1c0
[<ffffffff810e8264>] do_init_module+0x34/0x190
[<ffffffff810ea62f>] load_module+0x5cf/0x740
[<ffffffff810ea939>] SyS_init_module+0x99/0xd0
[<ffffffff815f8fd2>] system_call_fastpath+0x16/0x1b
irq event stamp: 336142
hardirqs last enabled at (336142): [<ffffffff810612f5>] __local_bh_enable_ip+0xb5/0xc0
hardirqs last disabled at (336141): [<ffffffff81061296>] __local_bh_enable_ip+0x56/0xc0
softirqs last enabled at (336004): [<ffffffff8106123a>] _local_bh_enable+0x4a/0x50
softirqs last disabled at (336005): [<ffffffff810617a4>] irq_exit+0x44/0xd0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&iboe->lock)->rlock);
<Interrupt>
lock(&(&iboe->lock)->rlock);
*** DEADLOCK ***
The above problem was caused by the spin lock being taken both in the process
context and in a soft-irq context (in a netdev notifier handler).
The required fix is to use spin_lock/unlock_bh() instead of spin_lock/unlock
on the iboe lock.
Reported-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When a RoCE port becomes active and the netdev of the port has upper
device (e.g bond/team), GIDs derived from the upper dev should appear
in the port's RoCE GID table.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
There's no need to reset the gid table twice and we need to do it only
for Ethernet ports. Also, no need to actively scan ndetdevs since it's
being done immediatly after we register netdev notifiers.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When reading the IPv6 addresses from the net-device, make sure to
avoid adding a duplicate entry to the GID table because of equality
between the default GID we generate and the default IPv6 link-local
address of the device.
Fixes: acc4fccf4e ("IB/mlx4: Make sure GID index 0 is always occupied")
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When Ethernet netdev is not present for a port (e.g. when the link
layer type of the port is InfiniBand) it's possible to dereference a
null pointer when we do netdevice scanning.
To fix that, we move a section of code that needs to run only when
netdev is present to a proper if () statement.
Fixes: ad4885d279 ("IB/mlx4: Build the port IBoE GID table properly under bonding")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
We need to fail the bind operation if the iser connection state != UP
(started teardown) and this should be done under the state lock.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When failing to allocate TX CQ we already allocated RX CQ, so we need to make
sure we release it. Also, when failing to register notification to the RX CQ
we currently leak both RX and TX CQs of the current index, fix that too.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
ocrdma_query_ah() does not use correct macro, and checks the wrong bit
for the validity of address handle in vector table. Fix this.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Because of IP-based GIDs, userspace AHs must have MAC and VLAN ID
resolved separately. Presently, user AHs are broken for ocrdma. This
patch resolves L2 addresses while creating user AH and obtains the
right DMAC and VLAN ID before creating AH.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch addresses feedback from Sagi Grimberg on the rereg_mr
implementation of mlx4. The following are fixed:
1. Set the correct pd_flags
2. Make sure we change the iova and size MR fields only after
successful write and allocation of the MTTs.
3. Make the error checking more robust
Fixes: e630664c83 ("mlx4_core: Add helper functions to support MR re-registration")
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Pull workqueue fix from Tejun Heo:
"create_singlethread_workqueue() is the old interface which is kept
around for backward compatibility - each should be reviewed to
determine whether singlethread usage was to save worker threads or for
ordering guarantee and whether it's depended upon by memory reclaim
path.
While adding NUMA support for unbound workqueues during v3.10, I
forgot to update it breaking the singlethread and ordering properties
on NUMA setups. The breakage was unfortunately rather subtle and went
without being reported until now.
The only missing piece is __WQ_ORDERED flag which makes the unbounded
workqueue use a single backend queue across different NUMA nodes.
It's fixed by making create_singlethread_workqueue() wrap
alloc_ordered_workqueue() so that possible future updates are
inherited automatically"
* 'for-3.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: apply __WQ_ORDERED to create_singlethread_workqueue()
On 32-bit architectures, the legacy buffer_head functions are not always
handling the sector number with the proper 64-bit types, and will thus
fail on 4TB+ disks.
Any code that uses __getblk() (and thus bread(), breadahead(),
sb_bread(), sb_breadahead(), sb_getblk()), and calls it using a 64-bit
block on a 32-bit arch (where "long" is 32-bit) causes an inifinite loop
in __getblk_slow() with an infinite stream of errors logged to dmesg
like this:
__find_get_block_slow() failed. block=6740375944, b_blocknr=2445408648
b_state=0x00000020, b_size=512
device sda1 blocksize: 512
Note how in hex block is 0x191C1F988 and b_blocknr is 0x91C1F988 i.e. the
top 32-bits are missing (in this case the 0x1 at the top).
This is because grow_dev_page() is broken and has a 32-bit overflow due
to shifting the page index value (a pgoff_t - which is just 32 bits on
32-bit architectures) left-shifted as the block number. But the top
bits to get lost as the pgoff_t is not type cast to sector_t / 64-bit
before the shift.
This patch fixes this issue by type casting "index" to sector_t before
doing the left shift.
Note this is not a theoretical bug but has been seen in the field on a
4TiB hard drive with logical sector size 512 bytes.
This patch has been verified to fix the infinite loop problem on 3.17-rc5
kernel using a 4TB disk image mounted using "-o loop". Without this patch
doing a "find /nt" where /nt is an NTFS volume causes the inifinite loop
100% reproducibly whilst with the patch it works fine as expected.
Signed-off-by: Anton Altaparmakov <aia21@cantab.net>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While debugging a cpufreq-related hardware failure on a system I saw the
following lockdep warning:
=========================
[ BUG: held lock freed! ] 3.17.0-rc4+ #1 Tainted: G E
-------------------------
insmod/2247 is freeing memory ffff88006e1b1400-ffff88006e1b17ff, with a lock still held there!
(&policy->rwsem){+.+...}, at: [<ffffffff8156d37d>] __cpufreq_add_dev.isra.21+0x47d/0xb80
3 locks held by insmod/2247:
#0: (subsys mutex#5){+.+.+.}, at: [<ffffffff81485579>] subsys_interface_register+0x69/0x120
#1: (cpufreq_rwsem){.+.+.+}, at: [<ffffffff8156cf73>] __cpufreq_add_dev.isra.21+0x73/0xb80
#2: (&policy->rwsem){+.+...}, at: [<ffffffff8156d37d>] __cpufreq_add_dev.isra.21+0x47d/0xb80
stack backtrace:
CPU: 0 PID: 2247 Comm: insmod Tainted: G E 3.17.0-rc4+ #1
Hardware name: HP ProLiant MicroServer Gen8, BIOS J06 08/24/2013
0000000000000000 000000008f3063c4 ffff88006f87bb30 ffffffff8171b358
ffff88006bcf3750 ffff88006f87bb68 ffffffff810e09e1 ffff88006e1b1400
ffffea0001b86c00 ffffffff8156d327 ffff880073003500 0000000000000246
Call Trace:
[<ffffffff8171b358>] dump_stack+0x4d/0x66
[<ffffffff810e09e1>] debug_check_no_locks_freed+0x171/0x180
[<ffffffff8156d327>] ? __cpufreq_add_dev.isra.21+0x427/0xb80
[<ffffffff8121412b>] kfree+0xab/0x2b0
[<ffffffff8156d327>] __cpufreq_add_dev.isra.21+0x427/0xb80
[<ffffffff81724cf7>] ? _raw_spin_unlock+0x27/0x40
[<ffffffffa003517f>] ? pcc_cpufreq_do_osc+0x17f/0x17f [pcc_cpufreq]
[<ffffffff8156da8e>] cpufreq_add_dev+0xe/0x10
[<ffffffff814855d1>] subsys_interface_register+0xc1/0x120
[<ffffffff8156bcf2>] cpufreq_register_driver+0x112/0x340
[<ffffffff8121415a>] ? kfree+0xda/0x2b0
[<ffffffffa003517f>] ? pcc_cpufreq_do_osc+0x17f/0x17f [pcc_cpufreq]
[<ffffffffa003562e>] pcc_cpufreq_init+0x4af/0xe81 [pcc_cpufreq]
[<ffffffffa003517f>] ? pcc_cpufreq_do_osc+0x17f/0x17f [pcc_cpufreq]
[<ffffffff81002144>] do_one_initcall+0xd4/0x210
[<ffffffff811f7472>] ? __vunmap+0xd2/0x120
[<ffffffff81127155>] load_module+0x1315/0x1b70
[<ffffffff811222a0>] ? store_uevent+0x70/0x70
[<ffffffff811229d9>] ? copy_module_from_fd.isra.44+0x129/0x180
[<ffffffff81127b86>] SyS_finit_module+0xa6/0xd0
[<ffffffff81725b69>] system_call_fastpath+0x16/0x1b
cpufreq: __cpufreq_add_dev: ->get() failed
insmod: ERROR: could not insert module pcc-cpufreq.ko: No such device
The warning occurs in the __cpufreq_add_dev() code which does
down_write(&policy->rwsem);
...
if (cpufreq_driver->get && !cpufreq_driver->setpolicy) {
policy->cur = cpufreq_driver->get(policy->cpu);
if (!policy->cur) {
pr_err("%s: ->get() failed\n", __func__);
goto err_get_freq;
}
If cpufreq_driver->get(policy->cpu) returns an error we execute the
code at err_get_freq, which does not up the policy->rwsem. This causes
the lockdep warning.
Trivial patch to up the policy->rwsem in the error path.
After the patch has been applied, and an error occurs in the
cpufreq_driver->get(policy->cpu) call we will now see
cpufreq: __cpufreq_add_dev: ->get() failed
cpufreq: __cpufreq_add_dev: ->get() failed
modprobe: ERROR: could not insert 'pcc_cpufreq': No such device
Fixes: 4e97b631f2 (cpufreq: Initialize governor for a new policy under policy->rwsem)
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 3.14+ <stable@vger.kernel.org> # 3.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cpufreq core introduces cpufreq_suspended flag to let cpufreq sysfs nodes
across S2RAM/S2DISK. But the flag is only set in the cpufreq_suspend()
for cpufreq drivers which have target or target_index callback. This
skips intel_pstate driver. This patch is to set the flag before checking
target or target_index callback.
Fixes: 2f0aea9363 (cpufreq: suspend governors on system suspend/hibernate)
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+
[rjw: Subject]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is a typo, it should be negative -errno instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ThinkPad X201s has a working ACPI video backlight interface and is
shipped before Win8; then there is BIOS update that starts to query
_OSI("Windows 2012") and that would make our video module stop creating
backlight interface and caused problem for the user. Add it to the DMI
table to disable native backlight to fix this problem.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=81691
Link: https://bugzilla.kernel.org/show_bug.cgi?id=51231
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Reported-and-tested-by: Yves-Alexis Perez <corsac@debian.org>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Correct a simple mistake of checking the wrong variable
before a dereference, resulting in the dereference not being
properly protected by rcu_dereference().
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KoreController and KoreController2 need an EP1_CMD_DIMM_LEDS command to set
their LEDs, not EP1_CMD_WRITE_IO.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reported-and-tested-by: Brad Wilson <brad.wilson.00@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The calculated frame size was wrong because snd_pcm_format_physical_width()
actually returns the number of bits, not bytes.
Use snd_pcm_format_size() instead, which not only returns bytes, but also
simplifies the calculation.
Fixes: 8bea869c5e ("ALSA: PCM midlevel: improve fifo_size handling")
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If a devices is being recovered it is not InSync and is not Faulty.
If a read error is experienced on that device, fix_read_error()
will be called, but it ignores non-InSync devices. So it will
neither fix the error nor fail the device.
It is incorrect that fix_read_error() ignores non-InSync devices.
It should only ignore Faulty devices. So fix it.
This became a bug when we allowed reading from a device that was being
recovered. It is suitable for any subsequent -stable kernel.
Fixes: da8840a747
Cc: stable@vger.kernel.org (v3.5+)
Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Tested-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Both normal IO and resync IO can be retried with reschedule_retry()
and so be counted into ->nr_queued, but only normal IO gets counted in
->nr_pending.
Before the recent improvement to RAID1 resync there could only
possibly have been one or the other on the queue. When handling a
read failure it could only be normal IO. So when handle_read_error()
called freeze_array() the fact that freeze_array only compares
->nr_queued against ->nr_pending was safe.
But now that these two types can interleave, we can have both normal
and resync IO requests queued, so we need to count them both in
nr_pending.
This error can lead to freeze_array() hanging if there is a read
error, so it is suitable for -stable.
Fixes: 79ef3a8aa1
cc: stable@vger.kernel.org (v3.13+)
Reported-by: Brassow Jonathan <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
raise_barrier() uses next_resync as part of its calculations, so it
really should be updated first, instead of afterwards.
next_resync is always used under resync_lock so update it under
resync lock to, just before it is used. That is safest.
This could cause normal IO and resync IO to interact badly so
it suitable for -stable.
Fixes: 79ef3a8aa1
cc: stable@vger.kernel.org (v3.13+)
Signed-off-by: NeilBrown <neilb@suse.de>
next_resync is (approximately) the location for the next resync request.
However it does *not* reliably determine the earliest location
at which resync might be happening.
This is because resync requests can complete out of order, and
we only limit the number of current requests, not the distance
from the earliest pending request to the latest.
mddev->curr_resync_completed is a reliable indicator of the earliest
position at which resync could be happening. It is updated less
frequently, but is actually reliable which is more important.
So use it to determine if a write request is before the region
being resynced and so safe from conflict.
This error can allow resync IO to interfere with normal IO which
could lead to data corruption. Hence: stable.
Fixes: 79ef3a8aa1
cc: stable@vger.kernel.org (v3.13+)
Signed-off-by: NeilBrown <neilb@suse.de>
The resync/recovery process for raid1 was recently changed
so that writes could happen in parallel with resync providing
they were in different regions of the device.
There is a problem though: While a write request will always
wait for conflicting resync to complete, a resync request
will *not* always wait for conflicting writes to complete.
Two changes are needed to fix this:
1/ raise_barrier (which waits until it is safe to do resync)
must wait until current_window_requests is zero
2/ wait_battier (which waits at the start of a new write request)
must update current_window_requests if the request could
possible conflict with a concurrent resync.
As concurrent writes and resync can lead to data loss,
this patch is suitable for -stable.
Fixes: 79ef3a8aa1
Cc: stable@vger.kernel.org (v3.13+)
Cc: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If there are outstanding writes when close_sync is called,
the change to ->start_next_window might cause them to
decrement the wrong counter when they complete. Fix this
by merging the two counters into the one that will be decremented.
Having an incorrect value in a counter can cause raise_barrier()
to hangs, so this is suitable for -stable.
Fixes: 79ef3a8aa1
cc: stable@vger.kernel.org (v3.13+)
Signed-off-by: NeilBrown <neilb@suse.de>
This reverts commit 747dba7de2.
It breaks concurrent vbi and video capturing:
While v4l2->users is the number of users of the whole device (all device nodes),
v4l2_fh_is_singular() only checks the number of users of a specific device node.
As a result. if one device node is open and a second device node is opened
(closed), the device is reinitialized (streaming is stopped).
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
commit 79ef3a8aa1 made
it possible for reads to happen concurrently with resync.
This means that we need to be more careful where read_balancing
is allowed during resync - we can no longer be sure that any
resync that has already started will definitely finish.
So keep read_balancing to before recovery_cp, which is conservative
but safe.
This bug makes it possible to read from a device that doesn't
have up-to-date data, so it can cause data corruption.
So it is suitable for any kernel since 3.11.
Fixes: 79ef3a8aa1
cc: stable@vger.kernel.org (v3.13+)
Signed-off-by: NeilBrown <neilb@suse.de>
r1_bio->start_next_window is not initialised in the READ
case, so allow_barrier may incorrectly decrement
conf->current_window_requests
which can cause raise_barrier() to block forever.
Fixes: 79ef3a8aa1
cc: stable@vger.kernel.org (v3.13+)
Reported-by: Brassow Jonathan <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When both VBI and video are streaming, and video stream is stopped,
a subsequent trial to restart it will fail, because S_FMT will
return -EBUSY.
That prevents applications like zvbi to work properly.
Please notice that, while this fix it fully for zvbi, the
best is to get rid of streaming_users and res_get logic as a hole.
However, this single-line patch is better to be merged at -stable.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The poll documentation was incomplete: document how events (POLLPRI)
are handled and fix the documentation of what poll does for display devices
and streaming I/O.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Clarify what poll() returns if STREAMON was called but not QBUF.
Make explicit the different behavior for this scenario for
capture and output devices.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The recent conversion of saa7134 to vb2 unconvered a poll() bug that
broke the teletext applications alevt and mtt. These applications
expect that calling poll() without having called VIDIOC_STREAMON will
cause poll() to return POLLERR. That did not happen in vb2.
This patch fixes that behavior. It also fixes what should happen when
poll() is called when STREAMON is called but no buffers have been
queued. In that case poll() will also return POLLERR, but only for
capture queues since output queues will always return POLLOUT
anyway in that situation.
This brings the vb2 behavior in line with the old videobuf behavior.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The v4l2_ctrl_config struct must be zeroed before passing it to
v4l2_ctrl_new_custom(). This was always wrong, but with the recent
v4l2-ctrls.c changes this is now much more likely to lead to a
kernel bug.
This is the only place where this struct wasn't initialized properly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Pridvorov Andrey <ua0lnj@bk.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The log_status function should show HDMI information, but the test checking for
an HDMI input was inverted. Fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org # for v3.12 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix build errors in radio-miropcm20.c due to missing header file:
drivers/media/radio/radio-miropcm20.c: In function 'rds_waitread':
drivers/media/radio/radio-miropcm20.c:90:3: error: implicit declaration of function 'inb' [-Werror=implicit-function-declaration]
drivers/media/radio/radio-miropcm20.c: In function 'rds_rawwrite':
drivers/media/radio/radio-miropcm20.c:106:3: error: implicit declaration of function 'outb' [-Werror=implicit-function-declaration]
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It's also invalid when plane_no is equal to vb->num_planes
Signed-off-by: Zhaowei Yuan <zhaowei.yuan@samsung.com>
Cc: stable@vger.kernel.org # for v3.7 and up
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Note: the revision text for the v4l2_pix_format change from Laurent
erroneously mentioned 3.16 when it only got merged for 3.17. Fixed
that as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit bd994ddb2a (vb2: Fix stream start and
buffer completion race) broke the buffer state check in vb2_buffer_done.
So accept all three possible states there since I can no longer tell the
difference between vb2_buffer_done called from start_streaming or from
elsewhere.
Instead add a WARN_ON at the end of start_streaming that will check whether
any buffers were added to the done list, since that implies that the wrong
state was used as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@vger.kernel.org # for v3.15 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The comment for start_streaming that tells the developer with which vb2 state
buffers should be returned to vb2 gave the wrong state. Very confusing.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Recently WARN_ON() calls have been added to warn if the driver is not
properly returning buffers to vb2 in start_streaming (if it fails) or
stop_streaming(). Add comments before those WARN_ON calls that refer
to the videobuf2-core.h header that explains what drivers are supposed
to do in these situations. That should help point developers in the
right direction if they see these warnings.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Pull ARM fixes from Russell King:
"Fixes for ARM, the most notable being the fix from Nathan Lynch to fix
the state of various registers during execve, to ensure that data
can't be leaked between two executables.
Fixes from Victor Kamensky for get_user() on big endian platforms,
since the addition of 8-byte get_user() support broke these fairly
badly.
A fix from Sudeep Holla for affinity setting when hotplugging CPU 0.
A fix from Stephen Boyd for a perf-induced sleep attempt while atomic.
Lastly, a correctness fix for emulation of the SWP instruction on
ARMv7+, and a fix for wrong carry handling when updating the
translation table base address on LPAE platforms"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8149/1: perf: Don't sleep while atomic when enabling per-cpu interrupts
ARM: 8148/1: flush TLS and thumbee register state during exec
ARM: 8151/1: add missing exports for asm functions required by get_user macro
ARM: 8137/1: fix get_user BE behavior for target variable with size of 8 bytes
ARM: 8135/1: Fix in-correct barrier usage in SWP{B} emulation
ARM: 8133/1: use irq_set_affinity with force=false when migrating irqs
ARM: 8132/1: LPAE: drop wrong carry flag correction after adding TTBR1_OFFSET
Using memset before strncpy just to ensure a trailing null character is
an unnecessary double writing of a string
Patch modified by Helge Deller to additionally reduce stack usage.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Helge Deller <deller@gmx.de>
