Just as we don't allow PDs, CQs, etc. to be destroyed if there are QPs
that are attached to them, don't let a QP be destroyed if there are
multicast group(s) attached to it. Use the existing usecnt field of
struct ib_qp which was added by commit 0e0ec7e ("RDMA/core: Export
ib_open_qp() to share XRC TGT QPs") to track this.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Use a bit in wc_flags rather then a whole integer to hold the
"checksum OK" flag. By itself, this change doesn't reduce the size of
struct ib_wc on 64bit machines -- it stays on 56 bytes because of
padding. However, it will allow to add more fields in the future
without enlarging the struct. Also, it will let us have a unified
approach with future libibverbs checksum offload reporting, because a
bit flag doesn't break the library ABI.
This patch was suggested during conversation with Liran Liss
<liranl@mellanox.com>.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The kernel IB stack uses one enumeration for IB speed, which wasn't
explicitly specified in the verbs header file. Add that enum, and use
it all over the code.
The IB speed/width notation is also used by iWARP and IBoE HW drivers,
which use the convention of rate = speed * width to advertise their
port link rate.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add defines for MAD error codes so that they can be used when
returning error responses.
Signed-off-by: Swapna Thete <swapna.thete@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Clean up sparse warnings in the rdma core layer.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (62 commits)
mlx4_core: Deprecate log_num_vlan module param
IB/mlx4: Don't set VLAN in IBoE WQEs' control segment
IB/mlx4: Enable 4K mtu for IBoE
RDMA/cxgb4: Mark QP in error before disabling the queue in firmware
RDMA/cxgb4: Serialize calls to CQ's comp_handler
RDMA/cxgb3: Serialize calls to CQ's comp_handler
IB/qib: Fix issue with link states and QSFP cables
IB/mlx4: Configure extended active speeds
mlx4_core: Add extended port capabilities support
IB/qib: Hold links until tuning data is available
IB/qib: Clean up checkpatch issue
IB/qib: Remove s_lock around header validation
IB/qib: Precompute timeout jiffies to optimize latency
IB/qib: Use RCU for qpn lookup
IB/qib: Eliminate divide/mod in converting idx to egr buf pointer
IB/qib: Decode path MTU optimization
IB/qib: Optimize RC/UC code by IB operation
IPoIB: Use the right function to do DMA unmap pages
RDMA/cxgb4: Use correct QID in insert_recv_cqe()
RDMA/cxgb4: Make sure flush CQ entries are collected on connection close
...
Allow processes that share the same XRC domain to open an existing
shareable QP. This permits those processes to receive events on the
shared QP and transfer ownership, so that any process may modify the
QP. The latter allows the creating process to exit, while a remaining
process can still transition it for path migration purposes.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
XRC TGT QPs are shared resources among multiple processes. Since the
creating process may exit, allow other processes which share the same
XRC domain to open an existing QP. This allows us to transfer
ownership of an XRC TGT QP to another process.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Allow the user to indicate the QP type separately from the port space
when allocating an rdma_cm_id. With RDMA_PS_IB, there is no longer a
1:1 relationship between the QP type and port space, so we need to
switch on the QP type to select between UD and connected QPs.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add RDMA_PS_IB. XRC QP types will use the IB port space when operating
over the RDMA CM. For the 'IP protocol' field value, we select 0x3F,
which is listed as being for 'any local network'.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
We require additional information to create XRC SRQs than we can
exchange using the existing create SRQ ABI. Provide an enhanced create
ABI for extended SRQ types.
Based on patches by Jack Morgenstein <jackm@dev.mellanox.co.il>
and Roland Dreier <roland@purestorage.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Allow user space to create XRC domains. Because XRCDs are expected to
be shared among multiple processes, we use inodes to identify an XRCD.
Based on patches by Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
XRC TGT QPs are intended to be shared among multiple users and
processes. Allow the destruction of an XRC TGT QP to be done explicitly
through ib_destroy_qp() or when the XRCD is destroyed.
To support destroying an XRC TGT QP, we need to track TGT QPs with the
XRCD. When the XRCD is destroyed, all tracked XRC TGT QPs are also
cleaned up.
To avoid stale reference issues, if a user is holding a reference on a
TGT QP, we increment a reference count on the QP. The user releases the
reference by calling ib_release_qp. This releases any access to the QP
from a user above verbs, but allows the QP to continue to exist until
destroyed by the XRCD.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
XRC ("eXtended reliable connected") is an IB transport that provides
better scalability by allowing senders to specify which shared receive
queue (SRQ) should be used to receive a message, which essentially
allows one transport context (QP connection) to serve multiple
destinations (as long as they share an adapter, of course).
XRC communication is between an initiator (INI) QP and a target (TGT)
QP. Target QPs are associated with SRQs through an XRCD. An XRC TGT QP
behaves like a receive-only RD QP. XRC INI QPs behave similarly to RC
QPs, except that work requests posted to an XRC INI QP must specify the
remote SRQ that is the target of the work request.
We define two new QP types for XRC, to distinguish between INI and TGT
QPs, and update the core layer to support XRC QPs.
This patch is derived from work by Jack Morgenstein
<jackm@dev.mellanox.co.il>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
XRC ("eXtended reliable connected") is an IB transport that provides
better scalability by allowing senders to specify which shared receive
queue (SRQ) should be used to receive a message, which essentially
allows one transport context (QP connection) to serve multiple
destinations (as long as they share an adapter, of course).
XRC defines SRQs that are specifically used by XRC connections. Expand
the SRQ code to support XRC SRQs. An XRC SRQ is currently restricted to
only XRC use according to the IB XRC Annex.
Portions of this patch were derived from work by
Jack Morgenstein <jackm@dev.mellanox.co.il>.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Currently, there is only a single ("basic") type of SRQ, but with XRC
support we will add a second. Prepare for this by defining an SRQ type
and setting all current users to IB_SRQT_BASIC.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
XRC ("eXtended reliable connected") is an IB transport that provides
better scalability by allowing senders to specify which shared receive
queue (SRQ) should be used to receive a message, which essentially
allows one transport context (QP connection) to serve multiple
destinations (as long as they share an adapter, of course).
A few new concepts are introduced to support this. This patch adds:
- A new device capability flag, IB_DEVICE_XRC, which low-level
drivers set to indicate that a device supports XRC.
- A new object type, XRC domains (struct ib_xrcd), and new verbs
ib_alloc_xrcd()/ib_dealloc_xrcd(). XRCDs are used to limit which
XRC SRQs an incoming message can target.
This patch is derived from work by Jack Morgenstein <jackm@dev.mellanox.co.il>.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Introduce support for the following extended speeds:
FDR-10: a Mellanox proprietary link speed which is 10.3125 Gbps with
64b/66b encoding rather than 8b/10b encoding.
FDR: IBA extended speed 14.0625 Gbps.
EDR: IBA extended speed 25.78125 Gbps.
Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il>
Reviewed-by: Hal Rosenstock <hal@mellanox.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Update struct iw_cm_event to support propagating the ird/ord values
upwards to the application.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch does several things:
- introduces __ethtool_get_settings which is called from ethtool code and
from drivers as well. Put ASSERT_RTNL there.
- dev_ethtool_get_settings() is replaced by __ethtool_get_settings()
- changes calling in drivers so rtnl locking is respected. In
iboe_get_rate was previously ->get_settings() called unlocked. This
fixes it. Also prb_calc_retire_blk_tmo() in af_packet.c had the same
problem. Also fixed by calling __dev_get_by_index() instead of
dev_get_by_index() and holding rtnl_lock for both calls.
- introduces rtnl_lock in bnx2fc_vport_create() and fcoe_vport_create()
so bnx2fc_if_create() and fcoe_if_create() are called locked as they
are from other places.
- use __ethtool_get_settings() in bonding code
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
v2->v3:
-removed dev_ethtool_get_settings()
-added ASSERT_RTNL into __ethtool_get_settings()
-prb_calc_retire_blk_tmo - use __dev_get_by_index() and lock
around it and __ethtool_get_settings() call
v1->v2:
add missing export_symbol
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> [except FCoE bits]
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the various definitions and mad structures needed for software
implementation of IBA PM agent from the ipath and qib drivers into a
single include file, which in turn could be used by more consumers.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add IB GID change event type. This is needed for IBoE when the HW
driver updates the GID (e.g when new VLANs are added/deleted) table
and the change should be reflected to the IB core cache.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/cma: Save PID of ID's owner
RDMA/cma: Add support for netlink statistics export
RDMA/cma: Pass QP type into rdma_create_id()
RDMA: Update exported headers list
RDMA/cma: Export enum cma_state in <rdma/rdma_cm.h>
RDMA/nes: Add a check for strict_strtoul()
RDMA/cxgb3: Don't post zero-byte read if endpoint is going away
RDMA/cxgb4: Use completion objects for event blocking
IB/srp: Fix integer -> pointer cast warnings
IB: Add devnode methods to cm_class and umad_class
IB/mad: Return EPROTONOSUPPORT when an RDMA device lacks the QP required
IB/uverbs: Add devnode method to set path/mode
RDMA/ucma: Add .nodename/.mode to tell userspace where to create device node
RDMA: Add netlink infrastructure
RDMA: Add error handling to ib_core_init()
Add callbacks and data types for statistics export of all current
devices/ids. The schema for RDMA CM is a series of netlink messages.
Each one contains an rdma_cm_stat struct. Additionally, two netlink
attributes are created for the addresses for each message (if
applicable).
Their types used are:
RDMA_NL_RDMA_CM_ATTR_SRC_ADDR (The source address for this ID)
RDMA_NL_RDMA_CM_ATTR_DST_ADDR (The destination address for this ID)
sockaddr_* structs are encapsulated within these attributes.
In other words, every transaction contains a series of messages like:
-------message 1-------
struct rdma_cm_id_stats {
__u32 qp_num;
__u32 bound_dev_if;
__u32 port_space;
__s32 pid;
__u8 cm_state;
__u8 node_type;
__u8 port_num;
__u8 reserved;
}
RDMA_NL_RDMA_CM_ATTR_SRC_ADDR attribute - contains the source address
RDMA_NL_RDMA_CM_ATTR_DST_ADDR attribute - contains the destination address
-------end 1-------
-------message 2-------
struct rdma_cm_id_stats
RDMA_NL_RDMA_CM_ATTR_SRC_ADDR attribute
RDMA_NL_RDMA_CM_ATTR_DST_ADDR attribute
-------end 2-------
Signed-off-by: Nir Muchtar <nirm@voltaire.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The RDMA CM currently infers the QP type from the port space selected
by the user. In the future (eg with RDMA_PS_IB or XRC), there may not
be a 1-1 correspondence between port space and QP type. For netlink
export of RDMA CM state, we want to export the QP type to userspace,
so it is cleaner to explicitly associate a QP type to an ID.
Modify rdma_create_id() to allow the user to specify the QP type, and
use it to make our selections of datagram versus connected mode.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Various RDMA headers are intended to be exported to userspace, so add
them to the headers-y list. Add a (strictly speaking, superfluous)
include of <linux/types.h> to avoid a headers_check warning.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Move cma.c's internal definition of enum cma_state to enum rdma_cm_state
in an exported header so that it can be exported via RDMA netlink.
Signed-off-by: Nir Muchtar <nirm@voltaire.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1446 commits)
macvlan: fix panic if lowerdev in a bond
tg3: Add braces around 5906 workaround.
tg3: Fix NETIF_F_LOOPBACK error
macvlan: remove one synchronize_rcu() call
networking: NET_CLS_ROUTE4 depends on INET
irda: Fix error propagation in ircomm_lmp_connect_response()
irda: Kill set but unused variable 'bytes' in irlan_check_command_param()
irda: Kill set but unused variable 'clen' in ircomm_connect_indication()
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_transport()
be2net: Kill set but unused variable 'req' in lancer_fw_download()
irda: Kill set but unused vars 'saddr' and 'daddr' in irlan_provider_connect_indication()
atl1c: atl1c_resume() is only used when CONFIG_PM_SLEEP is defined.
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_peer().
rxrpc: Kill set but unused variable 'local' in rxrpc_UDP_error_handler()
rxrpc: Kill set but unused variable 'sp' in rxrpc_process_connection()
rxrpc: Kill set but unused variable 'sp' in rxrpc_rotate_tx_window()
pkt_sched: Kill set but unused variable 'protocol' in tc_classify()
isdn: capi: Use pr_debug() instead of ifdefs.
tg3: Update version to 3.119
tg3: Apply rx_discards fix to 5719/5720
...
Fix up trivial conflicts in arch/x86/Kconfig and net/mac80211/agg-tx.c
as per Davem.
Add basic RDMA netlink infrastructure that allows for registration of
RDMA clients for which data is to be exported and supplies message
construction callbacks.
Signed-off-by: Nir Muchtar <nirm@voltaire.com>
[ Reorganize a few things, add CONFIG_NET dependency. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
The IW_CM_EVENT_STATUS_xxx values were used in only a couple of places;
cma.c uses -Exxx values instead, and so do the amso1100, cxgb3 and cxgb4
drivers -- only nes was using the enum values (with the mild consequence
that all nes connection failures were treated as generic errors rather
than reported as timeouts or rejections).
We can fix this confusion by getting rid of enum iw_cm_event_status and
using a plain int for struct iw_cm_event.status, and converting nes to
use -Exxx as the other iWARP drivers do.
This also gets rid of the warning
drivers/infiniband/core/cma.c: In function 'cma_iw_handler':
drivers/infiniband/core/cma.c:1333:3: warning: case value '4294967185' not in enumerated type 'enum iw_cm_event_status'
drivers/infiniband/core/cma.c:1336:3: warning: case value '4294967186' not in enumerated type 'enum iw_cm_event_status'
drivers/infiniband/core/cma.c:1332:3: warning: case value '4294967192' not in enumerated type 'enum iw_cm_event_status'
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Faisal Latif <faisal.latif@intel.com>
Lustre requires that clients bind to a privileged port number before
connecting to a remote server. On larger clusters (typically more
than about 1000 nodes), the number of privileged ports is exhausted,
resulting in lustre being unusable.
To handle this, we add support for reusable addresses to the rdma_cm.
This mimics the behavior of the socket option SO_REUSEADDR. A user
may set an rdma_cm_id to reuse an address before calling
rdma_bind_addr() (explicitly or implicitly). If set, other
rdma_cm_id's may be bound to the same address, provided that they all
have reuse enabled, and there are no active listens.
If rdma_listen() is called on an rdma_cm_id that has reuse enabled, it
will only succeed if there are no other id's bound to that same
address. The reuse option is exported to user space. The behavior of
the kernel reuse implementation was verified against that given by
sockets.
This patch is derived from a path by Ira Weiny <weiny2@llnl.gov>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This makes sure that when a driver calls the ethtool's
get/set_settings() callback of another driver, the data passed to it
is clean. This guarantees that speed_hi will be zeroed correctly if
the called callback doesn't explicitely set it: we are sure we don't
get a corrupted speed from the underlying driver. We also take care of
setting the cmd field appropriately (ETHTOOL_GSET/SSET).
This applies to dev_ethtool_get_settings(), which now makes sure it
sets up that ethtool command parameter correctly before passing it to
drivers. This also means that whoever calls dev_ethtool_get_settings()
does not have to clean the ethtool command parameter. This function
also becomes an exported symbol instead of an inline.
All drivers visible to make allyesconfig under x86_64 have been
updated.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* ib_wq is added, which is used as the common workqueue for infiniband
instead of the system workqueue. All system workqueue usages
including flush_scheduled_work() callers are converted to use and
flush ib_wq.
* cancel_delayed_work() + flush_scheduled_work() converted to
cancel_delayed_work_sync().
* qib_wq is removed and ib_wq is used instead.
This is to prepare for deprecation of flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add 802.1q VLAN support to IBoE. The VLAN tag is encoded within the
GID derived from a link local address in the following way:
GID[11] GID[12] contain the VLAN ID when the GID contains a VLAN.
The 3 bits user priority field of the packets are identical to the 3
bits of the SL.
In case of rdma_cm apps, the TOS field is used to generate the SL
field by doing a shift right of 5 bits effectively taking to 3 MS bits
of the TOS field.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for packing IBoE packet headers.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
[ Clean up and fix ib_ud_header_init() a bit. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for IBoE device binding and IP --> GID resolution. Path
resolving and multicast joining are implemented within cma.c by
filling in the responses and running callbacks in the CMA work queue.
IP --> GID resolution always yields IPv6 link local addresses; remote
GIDs are derived from the destination MAC address of the remote port.
Multicast GIDs are always mapped to multicast MACs as is done in IPv6.
(IPv4 multicast is enabled by translating IPv4 multicast addresses to
IPv6 multicast as described in
<http://www.mail-archive.com/ipng@sunroof.eng.sun.com/msg02134.html>.)
Some helper functions are added to ib_addr.h.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch allows ports to have different link layers:
IB_LINK_LAYER_INFINIBAND or IB_LINK_LAYER_ETHERNET. This is required
for adding IBoE (InfiniBand-over-Ethernet, aka RoCE) support. For
devices that do not provide an implementation for querying the link
layer property of a port, we return a default value based on the
transport: RMA_TRANSPORT_IB nodes will return IB_LINK_LAYER_INFINIBAND
and RDMA_TRANSPORT_IWARP nodes will return IB_LINK_LAYER_ETHERNET.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change abbreviated IB_QPT_RAW_ETY to IB_QPT_RAW_ETHERTYPE to make
the special QP type easier to understand.
cf http://www.mail-archive.com/linux-rdma@vger.kernel.org/msg04530.html
Signed-off-by: Aleksey Senin <alekseys@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a new parameter to ib_register_device() so that low-level device
drivers can pass in a pointer to a callback function that will be
called for each port that is registered in sysfs. This allows
low-level device drivers to create files in
/sys/class/infiniband/<hca>/ports/<N>/
without having to poke through the internals of the RDMA sysfs handling.
There is no need for an unregister function since the kobject
reference will go to zero when ib_unregister_device() is called.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- Add new IB_WR_MASKED_ATOMIC_CMP_AND_SWP and IB_WR_MASKED_ATOMIC_FETCH_AND_ADD
send opcodes that can be used to post "masked atomic compare and
swap" and "masked atomic fetch and add" work request respectively.
- Add masked_atomic_cap capability.
- Add mask fields to atomic struct of ib_send_wr
- Add new opcodes to ib_wc_opcode
The new operations are described more precisely below:
* Masked Compare and Swap (MskCmpSwap)
The MskCmpSwap atomic operation is an extension to the CmpSwap
operation defined in the IB spec. MskCmpSwap allows the user to
select a portion of the 64 bit target data for the “compare” check as
well as to restrict the swap to a (possibly different) portion. The
pseudo code below describes the operation:
| atomic_response = *va
| if (!((compare_add ^ *va) & compare_add_mask)) then
| *va = (*va & ~(swap_mask)) | (swap & swap_mask)
|
| return atomic_response
The additional operands are carried in the Extended Transport Header.
Atomic response generation and packet format for MskCmpSwap is as for
standard IB Atomic operations.
* Masked Fetch and Add (MFetchAdd)
The MFetchAdd Atomic operation extends the functionality of the
standard IB FetchAdd by allowing the user to split the target into
multiple fields of selectable length. The atomic add is done
independently on each one of this fields. A bit set in the
field_boundary parameter specifies the field boundaries. The pseudo
code below describes the operation:
| bit_adder(ci, b1, b2, *co)
| {
| value = ci + b1 + b2
| *co = !!(value & 2)
|
| return value & 1
| }
|
| #define MASK_IS_SET(mask, attr) (!!((mask)&(attr)))
| bit_position = 1
| carry = 0
| atomic_response = 0
|
| for i = 0 to 63
| {
| if ( i != 0 )
| bit_position = bit_position << 1
|
| bit_add_res = bit_adder(carry, MASK_IS_SET(*va, bit_position),
| MASK_IS_SET(compare_add, bit_position), &new_carry)
| if (bit_add_res)
| atomic_response |= bit_position
|
| carry = ((new_carry) && (!MASK_IS_SET(compare_add_mask, bit_position)))
| }
|
| return atomic_response
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ib_ud_header_init() first clears header and then fills up the various
fields. Later on, it tests header->immediate_present, which it has
already cleared, so the condition is always false. Fix this by adding
an immediate_present parameter and setting header->immediate_present
as is done with grh_present. Also remove unused calculation of
header_len.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A small change to reduce the size of ib_device to 1112 bytes
(from 1128).
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The defined SCTP number is incorrect (0x83, rather than 0x84), and
since it is not used anywhere, simply remove the definition.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
