SOF_TIMESTAMPING_OPT_ID puts the id in ee_data, not ee_info.
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is very similar to the macvlan driver except that it
uses L3 on the frame to determine the logical interface while
functioning as packet dispatcher. It inherits L2 of the master
device hence the packets on wire will have the same L2 for all
the packets originating from all virtual devices off of the same
master device.
This driver was developed keeping the namespace use-case in
mind. Hence most of the examples given here take that as the
base setup where main-device belongs to the default-ns and
virtual devices are assigned to the additional namespaces.
The device operates in two different modes and the difference
in these two modes in primarily in the TX side.
(a) L2 mode : In this mode, the device behaves as a L2 device.
TX processing upto L2 happens on the stack of the virtual device
associated with (namespace). Packets are switched after that
into the main device (default-ns) and queued for xmit.
RX processing is simple and all multicast, broadcast (if
applicable), and unicast belonging to the address(es) are
delivered to the virtual devices.
(b) L3 mode : In this mode, the device behaves like a L3 device.
TX processing upto L3 happens on the stack of the virtual device
associated with (namespace). Packets are switched to the
main-device (default-ns) for the L2 processing. Hence the routing
table of the default-ns will be used in this mode.
RX processins is somewhat similar to the L2 mode except that in
this mode only Unicast packets are delivered to the virtual device
while main-dev will handle all other packets.
The devices can be added using the "ip" command from the iproute2
package -
ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ]
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Laurent Chavey <chavey@google.com>
Cc: Tim Hockin <thockin@google.com>
Cc: Brandon Philips <brandon.philips@coreos.com>
Cc: Pavel Emelianov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently many changes have been done inside the driver
so this patch updates the driver's doc for example reviewing
information for the rx and tx processes that are managed
by napi method, adding new information for missing glue-logic files
etc.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was initially sent by Lorenzo Colitti, but was subsequently
lost in the final diff he submitted.
Signed-off-by: Loganaden Velvindron <logan@elandsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a sysctl that causes an interface's optimistic addresses
to be considered equivalent to other non-deprecated addresses
for source address selection purposes. Preferred addresses
will still take precedence over optimistic addresses, subject
to other ranking in the source address selection algorithm.
This is useful where different interfaces are connected to
different networks from different ISPs (e.g., a cell network
and a home wifi network).
The current behaviour complies with RFC 3484/6724, and it
makes sense if the host has only one interface, or has
multiple interfaces on the same network (same or cooperating
administrative domain(s), but not in the multiple distinct
networks case.
For example, if a mobile device has an IPv6 address on an LTE
network and then connects to IPv6-enabled wifi, while the wifi
IPv6 address is undergoing DAD, IPv6 connections will try use
the wifi default route with the LTE IPv6 address, and will get
stuck until they time out.
Also, because optimistic nodes can receive frames, issue
an RTM_NEWADDR as soon as DAD starts (with the IFA_F_OPTIMSTIC
flag appropriately set). A second RTM_NEWADDR is sent if DAD
completes (the address flags have changed), otherwise an
RTM_DELADDR is sent.
Also: add an entry in ip-sysctl.txt for optimistic_dad.
Signed-off-by: Erik Kline <ek@google.com>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing upcoming Yaogong patch (converting out of order queue
into an RB tree), I hit the max reordering level of linux TCP stack.
Reordering level was limited to 127 for no good reason, and some
network setups [1] can easily reach this limit and get limited
throughput.
Allow a new max limit of 300, and add a sysctl to allow admins to even
allow bigger (or lower) values if needed.
[1] Aggregation of links, per packet load balancing, fabrics not doing
deep packet inspections, alternative TCP congestion modules...
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yaogong Wang <wygivan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__sk_run_filter has been renamed as __bpf_prog_run, so replace them in comments
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Most notable changes in here:
1) By far the biggest accomplishment, thanks to a large range of
contributors, is the addition of multi-send for transmit. This is
the result of discussions back in Chicago, and the hard work of
several individuals.
Now, when the ->ndo_start_xmit() method of a driver sees
skb->xmit_more as true, it can choose to defer the doorbell
telling the driver to start processing the new TX queue entires.
skb->xmit_more means that the generic networking is guaranteed to
call the driver immediately with another SKB to send.
There is logic added to the qdisc layer to dequeue multiple
packets at a time, and the handling mis-predicted offloads in
software is now done with no locks held.
Finally, pktgen is extended to have a "burst" parameter that can
be used to test a multi-send implementation.
Several drivers have xmit_more support: i40e, igb, ixgbe, mlx4,
virtio_net
Adding support is almost trivial, so export more drivers to
support this optimization soon.
I want to thank, in no particular or implied order, Jesper
Dangaard Brouer, Eric Dumazet, Alexander Duyck, Tom Herbert, Jamal
Hadi Salim, John Fastabend, Florian Westphal, Daniel Borkmann,
David Tat, Hannes Frederic Sowa, and Rusty Russell.
2) PTP and timestamping support in bnx2x, from Michal Kalderon.
3) Allow adjusting the rx_copybreak threshold for a driver via
ethtool, and add rx_copybreak support to enic driver. From
Govindarajulu Varadarajan.
4) Significant enhancements to the generic PHY layer and the bcm7xxx
driver in particular (EEE support, auto power down, etc.) from
Florian Fainelli.
5) Allow raw buffers to be used for flow dissection, allowing drivers
to determine the optimal "linear pull" size for devices that DMA
into pools of pages. The objective is to get exactly the
necessary amount of headers into the linear SKB area pre-pulled,
but no more. The new interface drivers use is eth_get_headlen().
From WANG Cong, with driver conversions (several had their own
by-hand duplicated implementations) by Alexander Duyck and Eric
Dumazet.
6) Support checksumming more smoothly and efficiently for
encapsulations, and add "foo over UDP" facility. From Tom
Herbert.
7) Add Broadcom SF2 switch driver to DSA layer, from Florian
Fainelli.
8) eBPF now can load programs via a system call and has an extensive
testsuite. Alexei Starovoitov and Daniel Borkmann.
9) Major overhaul of the packet scheduler to use RCU in several major
areas such as the classifiers and rate estimators. From John
Fastabend.
10) Add driver for Intel FM10000 Ethernet Switch, from Alexander
Duyck.
11) Rearrange TCP_SKB_CB() to reduce cache line misses, from Eric
Dumazet.
12) Add Datacenter TCP congestion control algorithm support, From
Florian Westphal.
13) Reorganize sk_buff so that __copy_skb_header() is significantly
faster. From Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1558 commits)
netlabel: directly return netlbl_unlabel_genl_init()
net: add netdev_txq_bql_{enqueue, complete}_prefetchw() helpers
net: description of dma_cookie cause make xmldocs warning
cxgb4: clean up a type issue
cxgb4: potential shift wrapping bug
i40e: skb->xmit_more support
net: fs_enet: Add NAPI TX
net: fs_enet: Remove non NAPI RX
r8169:add support for RTL8168EP
net_sched: copy exts->type in tcf_exts_change()
wimax: convert printk to pr_foo()
af_unix: remove 0 assignment on static
ipv6: Do not warn for informational ICMP messages, regardless of type.
Update Intel Ethernet Driver maintainers list
bridge: Save frag_max_size between PRE_ROUTING and POST_ROUTING
tipc: fix bug in multicast congestion handling
net: better IFF_XMIT_DST_RELEASE support
net/mlx4_en: remove NETDEV_TX_BUSY
3c59x: fix bad split of cpu_to_le32(pci_map_single())
net: bcmgenet: fix Tx ring priority programming
...
- eBPF JIT compiler for arm64
- CPU suspend backend for PSCI (firmware interface) with standard idle
states defined in DT (generic idle driver to be merged via a different
tree)
- Support for CONFIG_DEBUG_SET_MODULE_RONX
- Support for unmapped cpu-release-addr (outside kernel linear mapping)
- set_arch_dma_coherent_ops() implemented and bus notifiers removed
- EFI_STUB improvements when base of DRAM is occupied
- Typos in KGDB macros
- Clean-up to (partially) allow kernel building with LLVM
- Other clean-ups (extern keyword, phys_addr_t usage)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SAfQ
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- eBPF JIT compiler for arm64
- CPU suspend backend for PSCI (firmware interface) with standard idle
states defined in DT (generic idle driver to be merged via a
different tree)
- Support for CONFIG_DEBUG_SET_MODULE_RONX
- Support for unmapped cpu-release-addr (outside kernel linear mapping)
- set_arch_dma_coherent_ops() implemented and bus notifiers removed
- EFI_STUB improvements when base of DRAM is occupied
- Typos in KGDB macros
- Clean-up to (partially) allow kernel building with LLVM
- Other clean-ups (extern keyword, phys_addr_t usage)
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (51 commits)
arm64: Remove unneeded extern keyword
ARM64: make of_device_ids const
arm64: Use phys_addr_t type for physical address
aarch64: filter $x from kallsyms
arm64: Use DMA_ERROR_CODE to denote failed allocation
arm64: Fix typos in KGDB macros
arm64: insn: Add return statements after BUG_ON()
arm64: debug: don't re-enable debug exceptions on return from el1_dbg
Revert "arm64: dmi: Add SMBIOS/DMI support"
arm64: Implement set_arch_dma_coherent_ops() to replace bus notifiers
of: amba: use of_dma_configure for AMBA devices
arm64: dmi: Add SMBIOS/DMI support
arm64: Correct ftrace calls to aarch64_insn_gen_branch_imm()
arm64:mm: initialize max_mapnr using function set_max_mapnr
setup: Move unmask of async interrupts after possible earlycon setup
arm64: LLVMLinux: Fix inline arm64 assembly for use with clang
arm64: pageattr: Correctly adjust unaligned start addresses
net: bpf: arm64: fix module memory leak when JIT image build fails
arm64: add PSCI CPU_SUSPEND based cpu_suspend support
arm64: kernel: introduce cpu_init_idle CPU operation
...
Pull documentation updates from Jiri Kosina:
"Updates to kernel documentation.
I took this over (hopefully temporarily) from Randy who was not
willing to maintain it any longer. This pile mostly is a relay of
queue that Randy already had in his tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/doc:
Documentation: fix broken v4l-utils URL
Documentation: update include path for mpssd
Documentation: correct parameter error for dma_mapping_error
MAINTAINERS: update location of linux-doc tree
Documentation: remove networking/.gitignore
tools: add more endian.h macros
Make Documenation depend on headers_install
Docs: this_cpu_ops: remove redundant add forms
Documentation: disable vdso_test to avoid breakage with old glibc
Documentation: update vDSO makefile to build portable examples
Documentation: update .gitignore files
Documentation: support glibc versions without htole macros
v4l2-pci-skeleton: Only build if PCI is available
Documentation: fix misc. warnings
Documentation: make functions static to avoid prototype warnings
Documentation: add makefiles for more targets
Documentation: use subdir-y to avoid unnecessary built-in.o files
1/ Step down as dmaengine maintainer see commit 08223d80df "dmaengine
maintainer update"
2/ Removal of net_dma, as it has been marked 'broken' since 3.13 (commit
7787380336 "net_dma: mark broken"), without reports of performance
regression.
3/ Miscellaneous fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BBBv
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine
Pull dmaengine updates from Dan Williams:
"Even though this has fixes marked for -stable, given the size and the
needed conflict resolutions this is 3.18-rc1/merge-window material.
These patches have been languishing in my tree for a long while. The
fact that I do not have the time to do proper/prompt maintenance of
this tree is a primary factor in the decision to step down as
dmaengine maintainer. That and the fact that the bulk of drivers/dma/
activity is going through Vinod these days.
The net_dma removal has not been in -next. It has developed simple
conflicts against mainline and net-next (for-3.18).
Continuing thanks to Vinod for staying on top of drivers/dma/.
Summary:
1/ Step down as dmaengine maintainer see commit 08223d80df
"dmaengine maintainer update"
2/ Removal of net_dma, as it has been marked 'broken' since 3.13
(commit 7787380336 "net_dma: mark broken"), without reports of
performance regression.
3/ Miscellaneous fixes"
* tag 'dmaengine-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine:
net: make tcp_cleanup_rbuf private
net_dma: revert 'copied_early'
net_dma: simple removal
dmaengine maintainer update
dmatest: prevent memory leakage on error path in thread
ioat: Use time_before_jiffies()
dmaengine: fix xor sources continuation
dma: mv_xor: Rename __mv_xor_slot_cleanup() to mv_xor_slot_cleanup()
dma: mv_xor: Remove all callers of mv_xor_slot_cleanup()
dma: mv_xor: Remove unneeded mv_xor_clean_completed_slots() call
ioat: Use pci_enable_msix_exact() instead of pci_enable_msix()
drivers: dma: Include appropriate header file in dca.c
drivers: dma: Mark functions as static in dma_v3.c
dma: mv_xor: Add DMA API error checks
ioat/dca: Use dev_is_pci() to check whether it is pci device
This patch demonstrates the effect of delaying update of HW tailptr.
(based on earlier patch by Jesper)
burst=1 is the default. It sends one packet with xmit_more=false
burst=2 sends one packet with xmit_more=true and
2nd copy of the same packet with xmit_more=false
burst=3 sends two copies of the same packet with xmit_more=true and
3rd copy with xmit_more=false
Performance with ixgbe (usec 30):
burst=1 tx:9.2 Mpps
burst=2 tx:13.5 Mpps
burst=3 tx:14.5 Mpps full 10G line rate
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work adds the DataCenter TCP (DCTCP) congestion control
algorithm [1], which has been first published at SIGCOMM 2010 [2],
resp. follow-up analysis at SIGMETRICS 2011 [3] (and also, more
recently as an informational IETF draft available at [4]).
DCTCP is an enhancement to the TCP congestion control algorithm for
data center networks. Typical data center workloads are i.e.
i) partition/aggregate (queries; bursty, delay sensitive), ii) short
messages e.g. 50KB-1MB (for coordination and control state; delay
sensitive), and iii) large flows e.g. 1MB-100MB (data update;
throughput sensitive). DCTCP has therefore been designed for such
environments to provide/achieve the following three requirements:
* High burst tolerance (incast due to partition/aggregate)
* Low latency (short flows, queries)
* High throughput (continuous data updates, large file
transfers) with commodity, shallow buffered switches
The basic idea of its design consists of two fundamentals: i) on the
switch side, packets are being marked when its internal queue
length > threshold K (K is chosen so that a large enough headroom
for marked traffic is still available in the switch queue); ii) the
sender/host side maintains a moving average of the fraction of marked
packets, so each RTT, F is being updated as follows:
F := X / Y, where X is # of marked ACKs, Y is total # of ACKs
alpha := (1 - g) * alpha + g * F, where g is a smoothing constant
The resulting alpha (iow: probability that switch queue is congested)
is then being used in order to adaptively decrease the congestion
window W:
W := (1 - (alpha / 2)) * W
The means for receiving marked packets resp. marking them on switch
side in DCTCP is the use of ECN.
RFC3168 describes a mechanism for using Explicit Congestion Notification
from the switch for early detection of congestion, rather than waiting
for segment loss to occur.
However, this method only detects the presence of congestion, not
the *extent*. In the presence of mild congestion, it reduces the TCP
congestion window too aggressively and unnecessarily affects the
throughput of long flows [4].
DCTCP, as mentioned, enhances Explicit Congestion Notification (ECN)
processing to estimate the fraction of bytes that encounter congestion,
rather than simply detecting that some congestion has occurred. DCTCP
then scales the TCP congestion window based on this estimate [4],
thus it can derive multibit feedback from the information present in
the single-bit sequence of marks in its control law. And thus act in
*proportion* to the extent of congestion, not its *presence*.
Switches therefore set the Congestion Experienced (CE) codepoint in
packets when internal queue lengths exceed threshold K. Resulting,
DCTCP delivers the same or better throughput than normal TCP, while
using 90% less buffer space.
It was found in [2] that DCTCP enables the applications to handle 10x
the current background traffic, without impacting foreground traffic.
Moreover, a 10x increase in foreground traffic did not cause any
timeouts, and thus largely eliminates TCP incast collapse problems.
The algorithm itself has already seen deployments in large production
data centers since then.
We did a long-term stress-test and analysis in a data center, short
summary of our TCP incast tests with iperf compared to cubic:
This test measured DCTCP throughput and latency and compared it with
CUBIC throughput and latency for an incast scenario. In this test, 19
senders sent at maximum rate to a single receiver. The receiver simply
ran iperf -s.
The senders ran iperf -c <receiver> -t 30. All senders started
simultaneously (using local clocks synchronized by ntp).
This test was repeated multiple times. Below shows the results from a
single test. Other tests are similar. (DCTCP results were extremely
consistent, CUBIC results show some variance induced by the TCP timeouts
that CUBIC encountered.)
For this test, we report statistics on the number of TCP timeouts,
flow throughput, and traffic latency.
1) Timeouts (total over all flows, and per flow summaries):
CUBIC DCTCP
Total 3227 25
Mean 169.842 1.316
Median 183 1
Max 207 5
Min 123 0
Stddev 28.991 1.600
Timeout data is taken by measuring the net change in netstat -s
"other TCP timeouts" reported. As a result, the timeout measurements
above are not restricted to the test traffic, and we believe that it
is likely that all of the "DCTCP timeouts" are actually timeouts for
non-test traffic. We report them nevertheless. CUBIC will also include
some non-test timeouts, but they are drawfed by bona fide test traffic
timeouts for CUBIC. Clearly DCTCP does an excellent job of preventing
TCP timeouts. DCTCP reduces timeouts by at least two orders of
magnitude and may well have eliminated them in this scenario.
2) Throughput (per flow in Mbps):
CUBIC DCTCP
Mean 521.684 521.895
Median 464 523
Max 776 527
Min 403 519
Stddev 105.891 2.601
Fairness 0.962 0.999
Throughput data was simply the average throughput for each flow
reported by iperf. By avoiding TCP timeouts, DCTCP is able to
achieve much better per-flow results. In CUBIC, many flows
experience TCP timeouts which makes flow throughput unpredictable and
unfair. DCTCP, on the other hand, provides very clean predictable
throughput without incurring TCP timeouts. Thus, the standard deviation
of CUBIC throughput is dramatically higher than the standard deviation
of DCTCP throughput.
Mean throughput is nearly identical because even though cubic flows
suffer TCP timeouts, other flows will step in and fill the unused
bandwidth. Note that this test is something of a best case scenario
for incast under CUBIC: it allows other flows to fill in for flows
experiencing a timeout. Under situations where the receiver is issuing
requests and then waiting for all flows to complete, flows cannot fill
in for timed out flows and throughput will drop dramatically.
3) Latency (in ms):
CUBIC DCTCP
Mean 4.0088 0.04219
Median 4.055 0.0395
Max 4.2 0.085
Min 3.32 0.028
Stddev 0.1666 0.01064
Latency for each protocol was computed by running "ping -i 0.2
<receiver>" from a single sender to the receiver during the incast
test. For DCTCP, "ping -Q 0x6 -i 0.2 <receiver>" was used to ensure
that traffic traversed the DCTCP queue and was not dropped when the
queue size was greater than the marking threshold. The summary
statistics above are over all ping metrics measured between the single
sender, receiver pair.
The latency results for this test show a dramatic difference between
CUBIC and DCTCP. CUBIC intentionally overflows the switch buffer
which incurs the maximum queue latency (more buffer memory will lead
to high latency.) DCTCP, on the other hand, deliberately attempts to
keep queue occupancy low. The result is a two orders of magnitude
reduction of latency with DCTCP - even with a switch with relatively
little RAM. Switches with larger amounts of RAM will incur increasing
amounts of latency for CUBIC, but not for DCTCP.
4) Convergence and stability test:
This test measured the time that DCTCP took to fairly redistribute
bandwidth when a new flow commences. It also measured DCTCP's ability
to remain stable at a fair bandwidth distribution. DCTCP is compared
with CUBIC for this test.
At the commencement of this test, a single flow is sending at maximum
rate (near 10 Gbps) to a single receiver. One second after that first
flow commences, a new flow from a distinct server begins sending to
the same receiver as the first flow. After the second flow has sent
data for 10 seconds, the second flow is terminated. The first flow
sends for an additional second. Ideally, the bandwidth would be evenly
shared as soon as the second flow starts, and recover as soon as it
stops.
The results of this test are shown below. Note that the flow bandwidth
for the two flows was measured near the same time, but not
simultaneously.
DCTCP performs nearly perfectly within the measurement limitations
of this test: bandwidth is quickly distributed fairly between the two
flows, remains stable throughout the duration of the test, and
recovers quickly. CUBIC, in contrast, is slow to divide the bandwidth
fairly, and has trouble remaining stable.
CUBIC DCTCP
Seconds Flow 1 Flow 2 Seconds Flow 1 Flow 2
0 9.93 0 0 9.92 0
0.5 9.87 0 0.5 9.86 0
1 8.73 2.25 1 6.46 4.88
1.5 7.29 2.8 1.5 4.9 4.99
2 6.96 3.1 2 4.92 4.94
2.5 6.67 3.34 2.5 4.93 5
3 6.39 3.57 3 4.92 4.99
3.5 6.24 3.75 3.5 4.94 4.74
4 6 3.94 4 5.34 4.71
4.5 5.88 4.09 4.5 4.99 4.97
5 5.27 4.98 5 4.83 5.01
5.5 4.93 5.04 5.5 4.89 4.99
6 4.9 4.99 6 4.92 5.04
6.5 4.93 5.1 6.5 4.91 4.97
7 4.28 5.8 7 4.97 4.97
7.5 4.62 4.91 7.5 4.99 4.82
8 5.05 4.45 8 5.16 4.76
8.5 5.93 4.09 8.5 4.94 4.98
9 5.73 4.2 9 4.92 5.02
9.5 5.62 4.32 9.5 4.87 5.03
10 6.12 3.2 10 4.91 5.01
10.5 6.91 3.11 10.5 4.87 5.04
11 8.48 0 11 8.49 4.94
11.5 9.87 0 11.5 9.9 0
SYN/ACK ECT test:
This test demonstrates the importance of ECT on SYN and SYN-ACK packets
by measuring the connection probability in the presence of competing
flows for a DCTCP connection attempt *without* ECT in the SYN packet.
The test was repeated five times for each number of competing flows.
Competing Flows 1 | 2 | 4 | 8 | 16
------------------------------
Mean Connection Probability 1 | 0.67 | 0.45 | 0.28 | 0
Median Connection Probability 1 | 0.65 | 0.45 | 0.25 | 0
As the number of competing flows moves beyond 1, the connection
probability drops rapidly.
Enabling DCTCP with this patch requires the following steps:
DCTCP must be running both on the sender and receiver side in your
data center, i.e.:
sysctl -w net.ipv4.tcp_congestion_control=dctcp
Also, ECN functionality must be enabled on all switches in your
data center for DCTCP to work. The default ECN marking threshold (K)
heuristic on the switch for DCTCP is e.g., 20 packets (30KB) at
1Gbps, and 65 packets (~100KB) at 10Gbps (K > 1/7 * C * RTT, [4]).
In above tests, for each switch port, traffic was segregated into two
queues. For any packet with a DSCP of 0x01 - or equivalently a TOS of
0x04 - the packet was placed into the DCTCP queue. All other packets
were placed into the default drop-tail queue. For the DCTCP queue,
RED/ECN marking was enabled, here, with a marking threshold of 75 KB.
More details however, we refer you to the paper [2] under section 3).
There are no code changes required to applications running in user
space. DCTCP has been implemented in full *isolation* of the rest of
the TCP code as its own congestion control module, so that it can run
without a need to expose code to the core of the TCP stack, and thus
nothing changes for non-DCTCP users.
Changes in the CA framework code are minimal, and DCTCP algorithm
operates on mechanisms that are already available in most Silicon.
The gain (dctcp_shift_g) is currently a fixed constant (1/16) from
the paper, but we leave the option that it can be chosen carefully
to a different value by the user.
In case DCTCP is being used and ECN support on peer site is off,
DCTCP falls back after 3WHS to operate in normal TCP Reno mode.
ss {-4,-6} -t -i diag interface:
... dctcp wscale:7,7 rto:203 rtt:2.349/0.026 mss:1448 cwnd:2054
ssthresh:1102 ce_state 0 alpha 15 ab_ecn 0 ab_tot 735584
send 10129.2Mbps pacing_rate 20254.1Mbps unacked:1822 retrans:0/15
reordering:101 rcv_space:29200
... dctcp-reno wscale:7,7 rto:201 rtt:0.711/1.327 ato:40 mss:1448
cwnd:10 ssthresh:1102 fallback_mode send 162.9Mbps pacing_rate
325.5Mbps rcv_rtt:1.5 rcv_space:29200
More information about DCTCP can be found in [1-4].
[1] http://simula.stanford.edu/~alizade/Site/DCTCP.html
[2] http://simula.stanford.edu/~alizade/Site/DCTCP_files/dctcp-final.pdf
[3] http://simula.stanford.edu/~alizade/Site/DCTCP_files/dctcp_analysis-full.pdf
[4] http://tools.ietf.org/html/draft-bensley-tcpm-dctcp-00
Joint work with Florian Westphal and Glenn Judd.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Glenn Judd <glenn.judd@morganstanley.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per commit "77873803363c net_dma: mark broken" net_dma is no longer used
and there is no plan to fix it.
This is the mechanical removal of bits in CONFIG_NET_DMA ifdef guards.
Reverting the remainder of the net_dma induced changes is deferred to
subsequent patches.
Marked for stable due to Roman's report of a memory leak in
dma_pin_iovec_pages():
https://lkml.org/lkml/2014/9/3/177
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: David Whipple <whipple@securedatainnovations.ch>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: <stable@vger.kernel.org>
Reported-by: Roman Gushchin <klamm@yandex-team.ru>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
this patch adds all of eBPF verfier documentation and empty bpf_check()
The end goal for the verifier is to statically check safety of the program.
Verifier will catch:
- loops
- out of range jumps
- unreachable instructions
- invalid instructions
- uninitialized register access
- uninitialized stack access
- misaligned stack access
- out of range stack access
- invalid calling convention
More details in Documentation/networking/filter.txt
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BPF syscall is a multiplexor for a range of different operations on eBPF.
This patch introduces syscall with single command to create a map.
Next patch adds commands to access maps.
'maps' is a generic storage of different types for sharing data between kernel
and userspace.
Userspace example:
/* this syscall wrapper creates a map with given type and attributes
* and returns map_fd on success.
* use close(map_fd) to delete the map
*/
int bpf_create_map(enum bpf_map_type map_type, int key_size,
int value_size, int max_entries)
{
union bpf_attr attr = {
.map_type = map_type,
.key_size = key_size,
.value_size = value_size,
.max_entries = max_entries
};
return bpf(BPF_MAP_CREATE, &attr, sizeof(attr));
}
'union bpf_attr' is backwards compatible with future extensions.
More details in Documentation/networking/filter.txt and in manpage
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some missing files to .gitignore.
Push Documentation/.gitignore down into subdirectories.
Signed-off-by: Peter Foley <pefoley2@pefoley.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a bunch of previously unbuilt source files to the Documentation build
machinery.
Signed-off-by: Peter Foley <pefoley2@pefoley.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Change the Documentation makefiles from obj-m to subdir-y
to avoid generating unnecessary built-in.o files since nothing
in Documentation/ is ever linked in to vmlinux.
Signed-off-by: Peter Foley <pefoley2@pefoley.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Current ICMP rate limiting uses inetpeer cache, which is an RBL tree
protected by a lock, meaning that hosts can be stuck hard if all cpus
want to check ICMP limits.
When say a DNS or NTP server process is restarted, inetpeer tree grows
quick and machine comes to its knees.
iptables can not help because the bottleneck happens before ICMP
messages are even cooked and sent.
This patch adds a new global limitation, using a token bucket filter,
controlled by two new sysctl :
icmp_msgs_per_sec - INTEGER
Limit maximal number of ICMP packets sent per second from this host.
Only messages whose type matches icmp_ratemask are
controlled by this limit.
Default: 1000
icmp_msgs_burst - INTEGER
icmp_msgs_per_sec controls number of ICMP packets sent per second,
while icmp_msgs_burst controls the burst size of these packets.
Default: 50
Note that if we really want to send millions of ICMP messages per
second, we might extend idea and infra added in commit 04ca6973f7
("ip: make IP identifiers less predictable") :
add a token bucket in the ip_idents hash and no longer rely on inetpeer.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit c801e3cc19 ("ipv4: Clarify in docs that accept_local requires rp_filter.").
It is not needed anymore since commit 1dced6a854 ("ipv4: Restore accept_local behaviour in fib_validate_source()").
Suggested-by: Julian Anastasov <ja@ssi.bg>
Cc: Gregory Detal <gregory.detal@uclouvain.be>
Cc: Christoph Paasch <christoph.paasch@uclouvain.be>
Cc: Hannes Frederic Sowa <hannes@redhat.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Sébastien Barré <sebastien.barre@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
add BPF_LD_IMM64 instruction to load 64-bit immediate value into a register.
All previous instructions were 8-byte. This is first 16-byte instruction.
Two consecutive 'struct bpf_insn' blocks are interpreted as single instruction:
insn[0].code = BPF_LD | BPF_DW | BPF_IMM
insn[0].dst_reg = destination register
insn[0].imm = lower 32-bit
insn[1].code = 0
insn[1].imm = upper 32-bit
All unused fields must be zero.
Classic BPF has similar instruction: BPF_LD | BPF_W | BPF_IMM
which loads 32-bit immediate value into a register.
x64 JITs it as single 'movabsq %rax, imm64'
arm64 may JIT as sequence of four 'movk x0, #imm16, lsl #shift' insn
Note that old eBPF programs are binary compatible with new interpreter.
It helps eBPF programs load 64-bit constant into a register with one
instruction instead of using two registers and 4 instructions:
BPF_MOV32_IMM(R1, imm32)
BPF_ALU64_IMM(BPF_LSH, R1, 32)
BPF_MOV32_IMM(R2, imm32)
BPF_ALU64_REG(BPF_OR, R1, R2)
User space generated programs will use this instruction to load constants only.
To tell kernel that user space needs a pointer the _pseudo_ variant of
this instruction may be added later, which will use extra bits of encoding
to indicate what type of pointer user space is asking kernel to provide.
For example 'off' or 'src_reg' fields can be used for such purpose.
src_reg = 1 could mean that user space is asking kernel to validate and
load in-kernel map pointer.
src_reg = 2 could mean that user space needs readonly data section pointer
src_reg = 3 could mean that user space needs a pointer to per-cpu local data
All such future pseudo instructions will not be carrying the actual pointer
as part of the instruction, but rather will be treated as a request to kernel
to provide one. The kernel will verify the request_for_a_pointer, then
will drop _pseudo_ marking and will store actual internal pointer inside
the instruction, so the end result is the interpreter and JITs never
see pseudo BPF_LD_IMM64 insns and only operate on generic BPF_LD_IMM64 that
loads 64-bit immediate into a register. User space never operates on direct
pointers and verifier can easily recognize request_for_pointer vs other
instructions.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The JIT compiler emits A64 instructions. It supports eBPF only.
Legacy BPF is supported thanks to conversion by BPF core.
JIT is enabled in the same way as for other architectures:
echo 1 > /proc/sys/net/core/bpf_jit_enable
Or for additional compiler output:
echo 2 > /proc/sys/net/core/bpf_jit_enable
See Documentation/networking/filter.txt for more information.
The implementation passes all 57 tests in lib/test_bpf.c
on ARMv8 Foundation Model :) Also tested by Will on Juno platform.
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
A buffer is incorrectly zeroed to the length of the pointer. If
cfg_payload_len < sizeof(void *) this can overwrites unrelated memory.
The buffer contents are never read, so no need to zero.
Fixes: 8fe2f761ca ("net-timestamp: expand documentation")
Reported-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As in IPv6 people might increase the igmp query robustness variable to
make sure unsolicited state change reports aren't lost on the network. Add
and document this new knob to igmp code.
RFCs allow tuning this parameter back to first IGMP RFC, so we also use
this setting for all counters, including source specific multicast.
Also take over sysctl value when upping the interface and don't reuse
the last one seen on the interface.
Cc: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new sysctl_mld_qrv knob to configure the mldv1/v2 query
robustness variable. It specifies how many retransmit of unsolicited mld
retransmit should happen. Admins might want to tune this on lossy links.
Also reset mld state on interface down/up, so we pick up new sysctl
settings during interface up event.
IPv6 certification requests this knob to be available.
I didn't make this knob netns specific, as it is mostly a setting in a
physical environment and should be per host.
Cc: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expand Documentation/networking/timestamping.txt with new
interfaces and bytestream timestamping. Also minor
cleanup of the other text.
Import txtimestamp.c test of the new features.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Missing documentation for gc_thresh2 sysctl.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds newly added FCoE files to the build but only if FCoE module is configured.
Also, updates i40e document for added FCoE support.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
trivial rename to indicate that this functions performs classic BPF checking
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the PHY library documentation to describe how a specific PHY
driver can use the PAL MMD register access routines or override those
routines with it's own in the event the PHY does not support the IEEE
standard for reading and writing MMD phy registers.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SO_TIMESTAMPING API defines three types of timestamps: software,
hardware in raw format (hwtstamp) and hardware converted to system
format (syststamp). The last has been deprecated in favor of combining
hwtstamp with a PTP clock driver. There are no active users in the
kernel.
The option was device driver dependent. If set, but without hardware
support, the correct behavior is to return zero in the relevant field
in the SCM_TIMESTAMPING ancillary message. Without device drivers
implementing the option, this field is effectively always zero.
Remove the internal plumbing to dissuage new drivers from implementing
the feature. Keep the SOF_TIMESTAMPING_SYS_HARDWARE flag, however, to
avoid breaking existing applications that request the timestamp.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No device driver will ever return an skb_shared_info structure with
syststamp non-zero, so remove the branch that tests for this and
optionally marks the packet timestamp as TP_STATUS_TS_SYS_HARDWARE.
Do not remove the definition TP_STATUS_TS_SYS_HARDWARE, as processes
may refer to it.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes init_net's high_thresh limit to be the maximum for all
namespaces, thus introducing a global memory limit threshold equal to the
sum of the individual high_thresh limits which are capped.
It also introduces some sane minimums for low_thresh as it shouldn't be
able to drop below 0 (or > high_thresh in the unsigned case), and
overall low_thresh should not ever be above high_thresh, so we make the
following relations for a namespace:
init_net:
high_thresh - max(not capped), min(init_net low_thresh)
low_thresh - max(init_net high_thresh), min (0)
all other namespaces:
high_thresh = max(init_net high_thresh), min(namespace's low_thresh)
low_thresh = max(namespace's high_thresh), min(0)
The major issue with having low_thresh > high_thresh is that we'll
schedule eviction but never evict anything and thus rely only on the
timers.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
merge functionality into the eviction workqueue.
Instead of rebuilding every n seconds, take advantage of the upper
hash chain length limit.
If we hit it, mark table for rebuild and schedule workqueue.
To prevent frequent rebuilds when we're completely overloaded,
don't rebuild more than once every 5 seconds.
ipfrag_secret_interval sysctl is now obsolete and has been marked as
deprecated, it still can be changed so scripts won't be broken but it
won't have any effect. A comment is left above each unused secret_timer
variable to avoid confusion.
Joint work with Nikolay Aleksandrov.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the high_thresh limit is reached we try to toss the 'oldest'
incomplete fragment queues until memory limits are below the low_thresh
value. This happens in softirq/packet processing context.
This has two drawbacks:
1) processors might evict a queue that was about to be completed
by another cpu, because they will compete wrt. resource usage and
resource reclaim.
2) LRU list maintenance is expensive.
But when constantly overloaded, even the 'least recently used' element is
recent, so removing 'lru' queue first is not 'fairer' than removing any
other fragment queue.
This moves eviction out of the fast path:
When the low threshold is reached, a work queue is scheduled
which then iterates over the table and removes the queues that exceed
the memory limits of the namespace. It sets a new flag called
INET_FRAG_EVICTED on the evicted queues so the proper counters will get
incremented when the queue is forcefully expired.
When the high threshold is reached, no more fragment queues are
created until we're below the limit again.
The LRU list is now unused and will be removed in a followup patch.
Joint work with Nikolay Aleksandrov.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document the Layer 2 hash factors with packet type ID field.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: David S. Miller <davem@davemloft.net>
CC: Pan Jiafei <Jiafei.Pan@freescale.com>
Signed-off-by: Jianhua Xie <jianhua.xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SO_TIMESTAMPING API defines option SOF_TIMESTAMPING_SYS_HW.
This feature is deprecated. It should not be implemented by new
device drivers. Existing drivers do not implement it, either --
with one exception.
Driver developers are encouraged to expose the NIC hw clock as a
PTP HW clock source, instead, and synchronize system time to the
HW source.
The control flag cannot be removed due to being part of the ABI, nor
can the structure scm_timestamping that is returned. Due to the one
legacy driver, the internal datapath and structure are not removed.
This patch only clearly marks the interface as deprecated. Device
drivers should always return a syststamp value of zero.
Signed-off-by: Willem de Bruijn <willemb@google.com>
----
We can consider adding a WARN_ON_ONCE in__sock_recv_timestamp
if non-zero syststamp is encountered
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Automatically generate flow labels for IPv6 packets on transmit.
The flow label is computed based on skb_get_hash. The flow label will
only automatically be set when it is zero otherwise (i.e. flow label
manager hasn't set one). This supports the transmit side functionality
of RFC 6438.
Added an IPv6 sysctl auto_flowlabels to enable/disable this behavior
system wide, and added IPV6_AUTOFLOWLABEL socket option to enable this
functionality per socket.
By default, auto flowlabels are disabled to avoid possible conflicts
with flow label manager, however if this feature proves useful we
may want to enable it by default.
It should also be noted that FreeBSD has already implemented automatic
flow labels (including the sysctl and socket option). In FreeBSD,
automatic flow labels default to enabled.
Performance impact:
Running super_netperf with 200 flows for TCP_RR and UDP_RR for
IPv6. Note that in UDP case, __skb_get_hash will be called for
every packet with explains slight regression. In the TCP case
the hash is saved in the socket so there is no regression.
Automatic flow labels disabled:
TCP_RR:
86.53% CPU utilization
127/195/322 90/95/99% latencies
1.40498e+06 tps
UDP_RR:
90.70% CPU utilization
118/168/243 90/95/99% latencies
1.50309e+06 tps
Automatic flow labels enabled:
TCP_RR:
85.90% CPU utilization
128/199/337 90/95/99% latencies
1.40051e+06
UDP_RR
92.61% CPU utilization
115/164/236 90/95/99% latencies
1.4687e+06
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using pktgen I'm seeing the ixgbe driver "push-back", due TX ring
running full. Thus, the TX ring is artificially limiting pktgen.
(Diagnose via "ethtool -S", look for "tx_restart_queue" or "tx_busy"
counters.)
Using ixgbe, the real reason behind the TX ring running full, is due
to TX ring not being cleaned up fast enough. The ixgbe driver combines
TX+RX ring cleanups, and the cleanup interval is affected by the
ethtool --coalesce setting of parameter "rx-usecs".
Do not increase the default NIC TX ring buffer or default cleanup
interval. Instead simply document that pktgen needs special NIC
tuning for maximum packet per sec performance.
Performance results with pktgen with clone_skb=100000.
TX ring size 512 (default), adjusting "rx-usecs":
(Single CPU performance, E5-2630, ixgbe)
- 3935002 pps - rx-usecs: 1 (irqs: 9346)
- 5132350 pps - rx-usecs: 10 (irqs: 99157)
- 5375111 pps - rx-usecs: 20 (irqs: 50154)
- 5454050 pps - rx-usecs: 30 (irqs: 33872)
- 5496320 pps - rx-usecs: 40 (irqs: 26197)
- 5502510 pps - rx-usecs: 50 (irqs: 21527)
TX ring size adjusting (ethtool -G), "rx-usecs==1" (default):
- 3935002 pps - tx-size: 512
- 5354401 pps - tx-size: 768
- 5356847 pps - tx-size: 1024
- 5327595 pps - tx-size: 1536
- 5356779 pps - tx-size: 2048
- 5353438 pps - tx-size: 4096
Notice after commit 6f25cd47d (pktgen: fix xmit test for BQL enabled
devices) pktgen uses netif_xmit_frozen_or_drv_stopped() and ignores
the BQL "stack" pause (QUEUE_STATE_STACK_XOFF) flag. This allow us to put
more pressure on the TX ring buffers.
It is the ixgbe_maybe_stop_tx() call that stops the transmits, and
pktgen respecting this in the call to netif_xmit_frozen_or_drv_stopped(txq).
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This can be used in virtual networking applications, and
may have other uses as well. The option is disabled by
default.
A specific use case is setting up virtual routers, bridges, and
hosts on a single OS without the use of network namespaces or
virtual machines. With proper use of ip rules, routing tables,
veth interface pairs and/or other virtual interfaces,
and applications that can bind to interfaces and/or IP addresses,
it is possibly to create one or more virtual routers with multiple
hosts attached. The host interfaces can act as IPv6 systems,
with radvd running on the ports in the virtual routers. With the
option provided in this patch enabled, those hosts can now properly
obtain IPv6 addresses from the radvd.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
This patch adds a description of eBPFs instruction encoding in order
to bring the documentation in line with the implementation.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the term eBPF is used anyway on mailing list discussions, lets
also document that in the main BPF documentation file and replace a
couple of occurrences with eBPF terminology to be more clear.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro 'A' used in internal BPF interpreter:
#define A regs[insn->a_reg]
was easily confused with the name of classic BPF register 'A', since
'A' would mean two different things depending on context.
This patch is trying to clean up the naming and clarify its usage in the
following way:
- A and X are names of two classic BPF registers
- BPF_REG_A denotes internal BPF register R0 used to map classic register A
in internal BPF programs generated from classic
- BPF_REG_X denotes internal BPF register R7 used to map classic register X
in internal BPF programs generated from classic
- internal BPF instruction format:
struct sock_filter_int {
__u8 code; /* opcode */
__u8 dst_reg:4; /* dest register */
__u8 src_reg:4; /* source register */
__s16 off; /* signed offset */
__s32 imm; /* signed immediate constant */
};
- BPF_X/BPF_K is 1 bit used to encode source operand of instruction
In classic:
BPF_X - means use register X as source operand
BPF_K - means use 32-bit immediate as source operand
In internal:
BPF_X - means use 'src_reg' register as source operand
BPF_K - means use 32-bit immediate as source operand
Suggested-by: Chema Gonzalez <chema@google.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Chema Gonzalez <chema@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull trivial tree changes from Jiri Kosina:
"Usual pile of patches from trivial tree that make the world go round"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
staging: go7007: remove reference to CONFIG_KMOD
aic7xxx: Remove obsolete preprocessor define
of: dma: doc fixes
doc: fix incorrect formula to calculate CommitLimit value
doc: Note need of bc in the kernel build from 3.10 onwards
mm: Fix printk typo in dmapool.c
modpost: Fix comment typo "Modules.symvers"
Kconfig.debug: Grammar s/addition/additional/
wimax: Spelling s/than/that/, wording s/destinatary/recipient/
aic7xxx: Spelling s/termnation/termination/
arm64: mm: Remove superfluous "the" in comment
of: Spelling s/anonymouns/anonymous/
dma: imx-sdma: Spelling s/determnine/determine/
ath10k: Improve grammar in comments
ath6kl: Spelling s/determnine/determine/
of: Improve grammar for of_alias_get_id() documentation
drm/exynos: Spelling s/contro/control/
radio-bcm2048.c: fix wrong overflow check
doc: printk-formats: do not mention casts for u64/s64
doc: spelling error changes
...
Conflicts:
drivers/net/bonding/bond_alb.c
drivers/net/ethernet/altera/altera_msgdma.c
drivers/net/ethernet/altera/altera_sgdma.c
net/ipv6/xfrm6_output.c
Several cases of overlapping changes.
The xfrm6_output.c has a bug fix which overlaps the renaming
of skb->local_df to skb->ignore_df.
In the Altera TSE driver cases, the register access cleanups
in net-next overlapped with bug fixes done in net.
Similarly a bug fix to send ALB packets in the bonding driver using
the right source address overlaps with cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Mention the recently added test suite in the documentation file.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 61b905da33 ("net: Rename skb->rxhash to skb->hash"), skb->rxhash
was renamed to skb->hash. Update references in Documentation
accordingly.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To benefit from special filters for single SFF or single EFF CAN identifier
subscriptions the CAN_EFF_FLAG bit and the CAN_RTR_FLAG bit has to be set
together with the CAN_(SFF|EFF)_MASK in can_filter.mask.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
An initial attempt on describing some of the odd APIs
provided by this driver.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
In particular, this patch tries to clarify internal BPF calling
convention and adds internal BPF examples, JIT guide, use cases.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/igb/e1000_mac.c
net/core/filter.c
Both conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The aggresive load balancing causes packet re-ordering as active
flows are moved from a slave to another within the group. Sometime
this aggresive lb is not necessary if the preference is for less
re-ordering. This parameter if used with value "0" disables
this dynamic flow shuffling minimizing packet re-ordering. Of course
the side effect is that it has to live with the static load balancing
that the hashing distribution provides. This impact is less severe if
the correct xmit-hashing-policy is used for the tlb setup.
The default value of the parameter is set to "1" mimicing the earlier
behavior.
Ran the netperf test with 200 stream for 1 min between two hosts with
4x1G trunk (xmit-lb mode with xmit-policy L3+4) before and after these
changes. Following was the command used for those 200 instances -
netperf -t TCP_RR -l 60 -s 5 -H <host> -- -r81920,81920
Transactions per second:
Before change: 1,367.11
After change: 1,470.65
Change-Id: Ie3f75c77282cf602e83a6e833c6eb164e72a0990
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-organized the xmit function for the lb mode separating tlb xmit
from the alb mode. This will enable use of the hashing policies
like 802.3ad mode. Also extended use of xmit-hash-policy to tlb mode.
Now the tlb-mode defaults to BOND_XMIT_POLICY_LAYER2 if the xmit policy
module parameter is not set (just like 802.3ad, or Xor mode).
Change-Id: I140257403d272df75f477b380207338d0f04963e
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added a new ancillary load (bpf call in eBPF parlance) that produces
a 32-bit random number. We are implementing it as an ancillary load
(instead of an ISA opcode) because (a) it is simpler, (b) allows easy
JITing, and (c) seems more in line with generic ISAs that do not have
"get a random number" as a instruction, but as an OS call.
The main use for this ancillary load is to perform random packet sampling.
Signed-off-by: Chema Gonzalez <chema@google.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Here is my initial pull request for the networking subsystem during
this merge window:
1) Support for ESN in AH (RFC 4302) from Fan Du.
2) Add full kernel doc for ethtool command structures, from Ben
Hutchings.
3) Add BCM7xxx PHY driver, from Florian Fainelli.
4) Export computed TCP rate information in netlink socket dumps, from
Eric Dumazet.
5) Allow IPSEC SA to be dumped partially using a filter, from Nicolas
Dichtel.
6) Convert many drivers to pci_enable_msix_range(), from Alexander
Gordeev.
7) Record SKB timestamps more efficiently, from Eric Dumazet.
8) Switch to microsecond resolution for TCP round trip times, also
from Eric Dumazet.
9) Clean up and fix 6lowpan fragmentation handling by making use of
the existing inet_frag api for it's implementation.
10) Add TX grant mapping to xen-netback driver, from Zoltan Kiss.
11) Auto size SKB lengths when composing netlink messages based upon
past message sizes used, from Eric Dumazet.
12) qdisc dumps can take a long time, add a cond_resched(), From Eric
Dumazet.
13) Sanitize netpoll core and drivers wrt. SKB handling semantics.
Get rid of never-used-in-tree netpoll RX handling. From Eric W
Biederman.
14) Support inter-address-family and namespace changing in VTI tunnel
driver(s). From Steffen Klassert.
15) Add Altera TSE driver, from Vince Bridgers.
16) Optimizing csum_replace2() so that it doesn't adjust the checksum
by checksumming the entire header, from Eric Dumazet.
17) Expand BPF internal implementation for faster interpreting, more
direct translations into JIT'd code, and much cleaner uses of BPF
filtering in non-socket ocntexts. From Daniel Borkmann and Alexei
Starovoitov"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1976 commits)
netpoll: Use skb_irq_freeable to make zap_completion_queue safe.
net: Add a test to see if a skb is freeable in irq context
qlcnic: Fix build failure due to undefined reference to `vxlan_get_rx_port'
net: ptp: move PTP classifier in its own file
net: sxgbe: make "core_ops" static
net: sxgbe: fix logical vs bitwise operation
net: sxgbe: sxgbe_mdio_register() frees the bus
Call efx_set_channels() before efx->type->dimension_resources()
xen-netback: disable rogue vif in kthread context
net/mlx4: Set proper build dependancy with vxlan
be2net: fix build dependency on VxLAN
mac802154: make csma/cca parameters per-wpan
mac802154: allow only one WPAN to be up at any given time
net: filter: minor: fix kdoc in __sk_run_filter
netlink: don't compare the nul-termination in nla_strcmp
can: c_can: Avoid led toggling for every packet.
can: c_can: Simplify TX interrupt cleanup
can: c_can: Store dlc private
can: c_can: Reduce register access
can: c_can: Make the code readable
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlM6jfsACgkQjTAFq1RaXHOVTwCeOyOYOJ+Ze2x33WydGcGsvX8a
QPoAoJVAcekmL5MVbcMTTvc8QL1AebAm
=4aEp
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-3.15-20140401' of git://gitorious.org/linux-can/linux-can
linux-can-fixes-for-3.15-20140401
Marc Kleine-Budde says:
====================
this is a pull request of 16 patches for the 3.15 release cycle.
Bjorn Van Tilt contributes a patch which fixes a memory leak in usb_8dev's
usb_8dev_start_xmit()s error path. A patch by Robert Schwebel fixes a typo in
the can documentation. The remaining patches all target the c_can driver. Two
of them are by me; they add a missing netif_napi_del() and return value
checking. Thomas Gleixner contributes 12 patches, which address several
shortcomings in the driver like hardware initialisation, concurrency, message
ordering and poor performance.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the name of the parameter to configure the sample point used
in iproute2's ip command. The correct writing is "sample-point" not
"sample_point".
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Further extend the current BPF documentation to document new BPF
engine internals. Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the MDIO bus documentation to mention that the MDIO bus reset
function is completely optional. It became optional with commit
e13934563d ("[PATCH] PHY Layer fixup")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
Documentation/devicetree/bindings/net/micrel-ks8851.txt
net/core/netpoll.c
The net/core/netpoll.c conflict is a bug fix in 'net' happening
to code which is completely removed in 'net-next'.
In micrel-ks8851.txt we simply have overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix double words "the the" in various files
within Documentations.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The documentation for how to use netlink mmap interface is incorrect.
The calls to setsockopt() require an additional argument.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since cd4d8fdad1 ("net: kernel panic in dev_hard_start_xmit:
remove faulty software TX time stamping") dev_hard_start_xmit()
will not provide software timestamps. It's a responsibility of
the drivers to call skb_tx_timestamp() at the right time.
Cc: linux-doc@vger.kernel.org
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Command line parameters QueuePairs, Node, EEE, DMAC and InterruptThrottleRate
do not exist these days. Remove all references to them in the Documentation
folder and update code comments.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a bindings description for the Altera Triple Speed Ethernet
(TSE) driver. The bindings support the legacy SGDMA soft IP as well as the
preferred MSGDMA soft IP. The TSE can be configured and synthesized in soft
logic using Altera's Quartus toolchain. Please consult the bindings document
for supported options.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/r8152.c
drivers/net/xen-netback/netback.c
Both the r8152 and netback conflicts were simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PK2i
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-devel-20140304' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
net-next: AF_RXRPC fixes and development
Here are some AF_RXRPC fixes:
(1) Fix to remove incorrect checksum calculation made during recvmsg(). It's
unnecessary to try to do this there since we check the checksum before
reading the RxRPC header from the packet.
(2) Fix to prevent the sending of an ABORT packet in response to another
ABORT packet and inducing a storm.
(3) Fix UDP MTU calculation from parsing ICMP_FRAG_NEEDED packets where we
don't handle the ICMP packet not specifying an MTU size.
And development patches:
(4) Add sysctls for configuring RxRPC parameters, specifically various delays
pertaining to ACK generation, the time before we resend a packet for
which we don't receive an ACK, the maximum time a call is permitted to
live and the amount of time transport, connection and dead call
information is cached.
(5) Improve ACK packet production by adjusting the handling of ACK_REQUESTED
packets, ignoring the MORE_PACKETS flag, delaying the production of
otherwise immediate ACK_IDLE packets and delaying all ACK_IDLE production
(barring the call termination) to half a second.
(6) Add more sysctl parameters to expose the Rx window size, the maximum
packet size that we're willing to receive and the number of jumbo rxrpc
packets we're willing to handle in a single UDP packet.
(7) Request ACKs on alternate DATA packets so that the other side doesn't
wait till we fill up the Tx window.
(8) Use a RCU hash table to look up the rxrpc_call for an incoming packet
rather than stepping through a hierarchy involving several spinlocks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The original documentation was very unclear.
The code fix is presumably related to the formerly unclear
documentation: SOCK_TIMESTAMPING_RX_SOFTWARE has no effect on
__sock_recv_timestamp's behavior, so calling __sock_recv_ts_and_drops
from sock_recv_ts_and_drops if only SOCK_TIMESTAMPING_RX_SOFTWARE is
set is pointless. This should have no user-observable effect.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
net/ipv6/sit.c
The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.
The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit e2d265d3b5 (canfd: add support for CAN FD in CAN_RAW sockets)
CAN FD frames with a payload length up to 8 byte are passed to legacy
sockets where the CAN FD support was not enabled by the application.
After some discussions with developers at a fair this well meant feature
leads to confusion as no clean switch for CAN / CAN FD is provided to the
application programmer. Additionally a compatibility like this for legacy
CAN_RAW sockets requires some compatibility handling for the sending, e.g.
make CAN2.0 frames a CAN FD frame with BRS at transmission time (?!?).
This will become a mess when people start to develop applications with
real CAN FD hardware. This patch reverts the bad compatibility code
together with the documentation describing the removed feature.
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Expose RxRPC parameters via sysctls to control the Rx window size, the Rx MTU
maximum size and the number of packets that can be glued into a jumbo packet.
More info added to Documentation/networking/rxrpc.txt.
Signed-off-by: David Howells <dhowells@redhat.com>
Add sysctls for configuring RxRPC protocol handling, specifically controls on
delays before ack generation, the delay before resending a packet, the maximum
lifetime of a call and the expiration times of calls, connections and
transports that haven't been recently used.
More info added in Documentation/networking/rxrpc.txt.
Signed-off-by: David Howells <dhowells@redhat.com>
The documentation misses a few of the supported flags. Fix this. Also
respect the dependency to CONFIG_XFRM for the IPSEC flag.
Cc: Fan Du <fan.du@windriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_3ad.h
drivers/net/bonding/bond_main.c
Two minor conflicts in bonding, both of which were overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently it's disabled because it's sometimes hard, in typical configs, to
make it work - because of the nature how the loadbalance modes work - as
it's hard to deliver valid arp replies to correct slaves by the switch.
However we still can use arp_validation in loadbalance with several other
configs, per example with arp_validate == 2 for backup with one broadcast
domain, without the switch(es) doing any balancing - this way we'd be (a
bit more) sure that the slave is up.
So, enable it to let users decide which one works/suits them best. Also
correct the mode limitation from BOND_OPT_ARP_VALIDATE.
CC: Nikolay Aleksandrov <nikolay@redhat.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Acked-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing the sysfs stubs for the Tx FIFOCFG and ATTRELI
(stashing) config registers, as these registers may only
be configured after a MAC reset, with the controller stopped
(i.e. during hw init, at probe() time). The current sysfs
stubs allow on-the-fly updates of these registers (the locking
measures are useless and only add unecessary code).
Changing these registers is discouraged. Only the default values
will be used instead.
Moreover, the stashing (ATTRELI) configuration options were
effectively disabled (didn't get to the hw anyway if changed)
because the stashing device_flags (HAS_BD_STASHING|HAS_BUF_STASHING)
were "accidentally" cleared during probe().
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY library was missing a bunch of newly added PHY driver callbacks
along with a smallish description of what they do, fix that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 684bad1107 "tcp: use PRR to reduce cwin in CWR state" removed all
calls to min_cwnd, so we can safely remove it.
Also, remove tcp_reno_min_cwnd because it was only used for min_cwnd.
Signed-off-by: Stanislav Fomichev <stfomichev@yandex-team.ru>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the commit 0e245dbaac
("drivers/net: delete the 3Com 3c505/3c507 intel i825xx support")
we clobbered the 3c505 driver (over a year ago) along with other
abandoned ISA drivers.
However, this orphaned README file escaped detection at that
time, and has lived on until today. Get rid of it now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the 00-INDEX files are somewhat outdated and some folders does
not contain 00-INDEX at all. Only outdated (with the notably exception
of spi) indexes are touched here, the 169 folders without 00-INDEX has
not been touched.
New 00-INDEX
- spi/* was added in a series of commits dating back to 2006
Added files (missing in (*/)00-INDEX)
- dmatest.txt was added by commit 851b7e16a0 ("dmatest: run test via
debugfs")
- this_cpu_ops.txt was added by commit a1b2a555d6 ("percpu: add
documentation on this_cpu operations")
- ww-mutex-design.txt was added by commit 040a0a3710 ("mutex: Add
support for wound/wait style locks")
- bcache.txt was added by commit cafe563591 ("bcache: A block layer
cache")
- kernel-per-CPU-kthreads.txt was added by commit 49717cb404
("kthread: Document ways of reducing OS jitter due to per-CPU
kthreads")
- phy.txt was added by commit ff76496347 ("drivers: phy: add generic
PHY framework")
- block/null_blk was added by commit 12f8f4fc03 ("null_blk:
documentation")
- module-signing.txt was added by commit 3cafea3076 ("Add
Documentation/module-signing.txt file")
- assoc_array.txt was added by commit 3cb989501c ("Add a generic
associative array implementation.")
- arm/IXP4xx was part of the initial repo
- arm/cluster-pm-race-avoidance.txt was added by commit 7fe31d28e8
("ARM: mcpm: introduce helpers for platform coherency exit/setup")
- arm/firmware.txt was added by commit 7366b92a77 ("ARM: Add
interface for registering and calling firmware-specific operations")
- arm/kernel_mode_neon.txt was added by commit 2afd0a0524 ("ARM:
7825/1: document the use of NEON in kernel mode")
- arm/tcm.txt was added by commit bc581770cf ("ARM: 5580/2: ARM TCM
(Tightly-Coupled Memory) support v3")
- arm/vlocks.txt was added by commit 9762f12d3e ("ARM: mcpm: Add
baremetal voting mutexes")
- blackfin/gptimers-example.c, Makefile was added by commit
4b60779d5e ("Blackfin: add an example showing how to use the
gptimers API")
- devicetree/usage-model.txt was added by commit 31134efc68 ("dt:
Linux DT usage model documentation")
- fb/api.txt was added by commit fb21c2f428 ("fbdev: Add FOURCC-based
format configuration API")
- fb/sm501.txt was added by commit e6a0498071 ("video, sm501: add
edid and commandline support")
- fb/udlfb.txt was added by commit 96f8d864af ("fbdev: move udlfb out
of staging.")
- filesystems/Makefile was added by commit 1e0051ae48
("Documentation/fs/: split txt and source files")
- filesystems/nfs/nfsd-admin-interfaces.txt was added by commit
8a4c6e19cf ("nfsd: document kernel interfaces for nfsd
configuration")
- ide/warm-plug-howto.txt was added by commit f74c91413e ("ide: add
warm-plug support for IDE devices (take 2)")
- laptops/Makefile was added by commit d49129accc
("Documentation/laptop/: split txt and source files")
- leds/leds-blinkm.txt was added by commit b54cf35a7f ("LEDS: add
BlinkM RGB LED driver, documentation and update MAINTAINERS")
- leds/ledtrig-oneshot.txt was added by commit 5e417281cd ("leds: add
oneshot trigger")
- leds/ledtrig-transient.txt was added by commit 44e1e9f8e7 ("leds:
add new transient trigger for one shot timer activation")
- m68k/README.buddha was part of the initial repo
- networking/LICENSE.(qla3xxx|qlcnic|qlge) was added by commits
40839129f7, c4e84bde1d, 5a4faa8737
- networking/Makefile was added by commit 3794f3e812 ("docsrc: build
Documentation/ sources")
- networking/i40evf.txt was added by commit 105bf2fe6b ("i40evf: add
driver to kernel build system")
- networking/ipsec.txt was added by commit b3c6efbc36 ("xfrm: Add
file to document IPsec corner case")
- networking/mac80211-auth-assoc-deauth.txt was added by commit
3cd7920a2b ("mac80211: add auth/assoc/deauth flow diagram")
- networking/netlink_mmap.txt was added by commit 5683264c39
("netlink: add documentation for memory mapped I/O")
- networking/nf_conntrack-sysctl.txt was added by commit c9f9e0e159
("netfilter: doc: add nf_conntrack sysctl api documentation") lan)
- networking/team.txt was added by commit 3d249d4ca7 ("net: introduce
ethernet teaming device")
- networking/vxlan.txt was added by commit d342894c5d ("vxlan:
virtual extensible lan")
- power/runtime_pm.txt was added by commit 5e928f77a0 ("PM: Introduce
core framework for run-time PM of I/O devices (rev. 17)")
- power/charger-manager.txt was added by commit 3bb3dbbd56
("power_supply: Add initial Charger-Manager driver")
- RCU/lockdep-splat.txt was added by commit d7bd2d68aa ("rcu:
Document interpretation of RCU-lockdep splats")
- s390/kvm.txt was added by 5ecee4b (KVM: s390: API documentation)
- s390/qeth.txt was added by commit b4d72c08b3 ("qeth: bridgeport
support - basic control")
- scheduler/sched-bwc.txt was added by commit 88ebc08ea9 ("sched: Add
documentation for bandwidth control")
- scsi/advansys.txt was added by commit 4bd6d7f356 ("[SCSI] advansys:
Move documentation to Documentation/scsi")
- scsi/bfa.txt was added by commit 1ec90174bd ("[SCSI] bfa: add
readme file")
- scsi/bnx2fc.txt was added by commit 12b8fc10ea ("[SCSI] bnx2fc: Add
driver documentation")
- scsi/cxgb3i.txt was added by commit c3673464eb ("[SCSI] cxgb3i: Add
cxgb3i iSCSI driver.")
- scsi/hpsa.txt was added by commit 992ebcf14f ("[SCSI] hpsa: Add
hpsa.txt to Documentation/scsi")
- scsi/link_power_management_policy.txt was added by commit
ca77329fb7 ("[libata] Link power management infrastructure")
- scsi/osd.txt was added by commit 78e0c621de ("[SCSI] osd:
Documentation for OSD library")
- scsi/scsi-parameter.txt was created/moved by commit 163475fb11
("Documentation: move SCSI parameters to their own text file")
- serial/driver was part of the initial repo
- serial/n_gsm.txt was added by commit 323e84122e ("n_gsm: add a
documentation")
- timers/Makefile was added by commit 3794f3e812 ("docsrc: build
Documentation/ sources")
- virt/kvm/s390.txt was added by commit d9101fca3d ("KVM: s390:
diagnose call documentation")
- vm/split_page_table_lock was added by commit 49076ec2cc ("mm:
dynamically allocate page->ptl if it cannot be embedded to struct
page")
- w1/slaves/w1_ds28e04 was added by commit fbf7f7b4e2 ("w1: Add
1-wire slave device driver for DS28E04-100")
- w1/masters/omap-hdq was added by commit e0a29382c6 ("hdq:
documentation for OMAP HDQ")
- x86/early-microcode.txt was added by commit 0d91ea86a8 ("x86, doc:
Documentation for early microcode loading")
- x86/earlyprintk.txt was added by commit a1aade4788 ("x86/doc:
mini-howto for using earlyprintk=dbgp")
- x86/entry_64.txt was added by commit 8b4777a4b5 ("x86-64: Document
some of entry_64.S")
- x86/pat.txt was added by commit d27554d874 ("x86: PAT
documentation")
Moved files
- arm/kernel_user_helpers.txt was moved out of arch/arm/kernel by
commit 37b8304642 ("ARM: kuser: move interface documentation out of
the source code")
- efi-stub.txt was moved out of x86/ and down into Documentation/ in
commit 4172fe2f8a ("EFI stub documentation updates")
- laptops/hpfall.c was moved out of hwmon/ and into laptops/ in commit
efcfed9bad ("Move hp_accel to drivers/platform/x86")
- commit 5616c23ad9 ("x86: doc: move x86-generic documentation from
Doc/x86/i386"):
* x86/usb-legacy-support.txt
* x86/boot.txt
* x86/zero_page.txt
- power/video_extension.txt was moved to acpi in commit 70e66e4df1
("ACPI / video: move video_extension.txt to Documentation/acpi")
Removed files (left in 00-INDEX)
- memory.txt was removed by commit 00ea8990aa ("memory.txt: remove
stray information")
- gpio.txt was moved to gpio/ in commit fd8e198cfc ("Documentation:
gpiolib: document new interface")
- networking/DLINK.txt was removed by commit 168e06ae26
("drivers/net: delete old parallel port de600/de620 drivers")
- serial/hayes-esp.txt was removed by commit f53a2ade0b ("tty: esp:
remove broken driver")
- s390/TAPE was removed by commit 9e280f6693 ("[S390] remove tape
block docu")
- vm/locking was removed by commit 57ea8171d2 ("mm: documentation:
remove hopelessly out-of-date locking doc")
- laptops/acer-wmi.txt was remvoed by commit 020036678e ("acer-wmi:
Delete out-of-date documentation")
Typos/misc issues
- rpc-server-gss.txt was added as knfsd-rpcgss.txt in commit
030d794bf4 ("SUNRPC: Use gssproxy upcall for server RPCGSS
authentication.")
- commit b88cf73d92 ("net: add missing entries to
Documentation/networking/00-INDEX")
* generic-hdlc.txt was added as generic_hdlc.txt
* spider_net.txt was added as spider-net.txt
- w1/master/mxc-w1 was added as mxc_w1 by commit a5fd9139f7 ("w1: add
1-wire master driver for i.MX27 / i.MX31")
- s390/zfcpdump.txt was added as zfcpdump by commit 6920c12a40
("[S390] Add Documentation/s390/00-INDEX.")
Signed-off-by: Henrik Austad <henrik@austad.us>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> [rcu bits]
Acked-by: Rob Landley <rob@landley.net>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Mark Brown <broonie@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Len Brown <len.brown@intel.com>
Cc: James Bottomley <JBottomley@parallels.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
From 038a821667f62c496f2bbae27081b1b612122a97 Mon Sep 17 00:00:00 2001
From: Martin Schwenke <martin@meltin.net>
Date: Tue, 28 Jan 2014 15:16:49 +1100
Subject: [PATCH] net: Document promote_secondaries
This option was added a long time ago...
commit 8f937c6099
Author: Harald Welte <laforge@gnumonks.org>
Date: Sun May 29 20:23:46 2005 -0700
[IPV4]: Primary and secondary addresses
Signed-off-by: Martin Schwenke <martin@meltin.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently I added a new AF_PACKET fanout operation mode in commit
2d36097, but I forgot to document it. Add PACKET_FANOUT_QM as an available mode
in the af_packet documentation. Applies to net-next.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current .init and .exit callbacks requires access to driver
private data structures. This is not a good seperation and abstraction.
Instead, we add a new .setup callback for allocating private data, and
pass the returned pointer to the other callbacks.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the introduction of IPV6_FL_F_REFLECT, there is no guarantee of
flow label unicity. This patch introduces a new sysctl to protect the old
behaviour, enable by default.
Changelog of V3:
* rename ip6_flowlabel_consistency to flowlabel_consistency
* use net_info_ratelimited()
* checkpatch cleanups
Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/xfrm/xfrm_policy.c
Steffen Klassert says:
====================
This pull request has a merge conflict between commits be7928d20b
("net: xfrm: xfrm_policy: fix inline not at beginning of declaration") and
da7c224b1b ("net: xfrm: xfrm_policy: silence compiler warning") from
the net-next tree and commit 2f3ea9a95c ("xfrm: checkpatch erros with
inline keyword position") from the ipsec-next tree.
The version from net-next can be used, like it is done in linux-next.
1) Checkpatch cleanups, from Weilong Chen.
2) Fix lockdep complaints when pktgen is used with IPsec,
from Fan Du.
3) Update pktgen to allow any combination of IPsec transport/tunnel mode
and AH/ESP/IPcomp type, from Fan Du.
4) Make pktgen_dst_metrics static, Fengguang Wu.
5) Compile fix for pktgen when CONFIG_XFRM is not set,
from Fan Du.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- drop dependency against CRC16
- move to new release version
- add size check at compile time for packet structs
- update copyright years in every file
- implement new bonding/interface alternation feature
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=BKos
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Included changes:
- drop dependency against CRC16
- move to new release version
- add size check at compile time for packet structs
- update copyright years in every file
- implement new bonding/interface alternation feature
Signed-off-by: David S. Miller <davem@davemloft.net>
Document how to use one AF_PACKET mmap socket for RX and TX.
Signed-off-by: Norbert van Bolhuis <nvbolhuis@aimvalley.nl>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new ip_no_pmtu_disc mode only allowes fragmentation-needed errors
to be honored by protocols which do more stringent validation on the
ICMP's packet payload. This knob is useful for people who e.g. want to
run an unmodified DNS server in a namespace where they need to use pmtu
for TCP connections (as they are used for zone transfers or fallback
for requests) but don't want to use possibly spoofed UDP pmtu information.
Currently the whitelisted protocols are TCP, SCTP and DCCP as they check
if the returned packet is in the window or if the association is valid.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: John Heffner <johnwheffner@gmail.com>
Suggested-by: Florian Weimer <fweimer@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While forwarding we should not use the protocol path mtu to calculate
the mtu for a forwarded packet but instead use the interface mtu.
We mark forwarded skbs in ip_forward with IPSKB_FORWARDED, which was
introduced for multicast forwarding. But as it does not conflict with
our usage in unicast code path it is perfect for reuse.
I moved the functions ip_sk_accept_pmtu, ip_sk_use_pmtu and ip_skb_dst_mtu
along with the new ip_dst_mtu_maybe_forward to net/ip.h to fix circular
dependencies because of IPSKB_FORWARDED.
Because someone might have written a software which does probe
destinations manually and expects the kernel to honour those path mtus
I introduced a new per-namespace "ip_forward_use_pmtu" knob so someone
can disable this new behaviour. We also still use mtus which are locked on a
route for forwarding.
The reason for this change is, that path mtus information can be injected
into the kernel via e.g. icmp_err protocol handler without verification
of local sockets. As such, this could cause the IPv4 forwarding path to
wrongfully emit fragmentation needed notifications or start to fragment
packets along a path.
Tunnel and ipsec output paths clear IPCB again, thus IPSKB_FORWARDED
won't be set and further fragmentation logic will use the path mtu to
determine the fragmentation size. They also recheck packet size with
help of path mtu discovery and report appropriate errors.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: John Heffner <johnwheffner@gmail.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing sysfs attributes in the proper section of the README
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
This change allows to follow a recommandation of RFC4942.
- Add "anycast_src_echo_reply" sysctl to control the use of anycast addresses
as source addresses for ICMPv6 echo reply. This sysctl is false by default
to preserve existing behavior.
- Add inline check ipv6_anycast_destination().
- Use them in icmpv6_echo_reply().
Reference:
RFC4942 - IPv6 Transition/Coexistence Security Considerations
(http://tools.ietf.org/html/rfc4942#section-2.1.6)
2.1.6. Anycast Traffic Identification and Security
[...]
To avoid exposing knowledge about the internal structure of the
network, it is recommended that anycast servers now take advantage of
the ability to return responses with the anycast address as the
source address if possible.
Signed-off-by: Francois-Xavier Le Bail <fx.lebail@yahoo.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update pktgen.txt for reference when using IPsec.
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Modify the existing Kconfig, Makefile, and MAINTAINERS to add the driver
to the kernel. Add a Makefile and a documentation
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Introduce TP_STATUS_VLAN_TPID_VALID bit into the documentation.
Signed-off-by: Atzm Watanabe <atzm@stratosphere.co.jp>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2013-12-19
1) Use the user supplied policy index instead of a generated one
if present. From Fan Du.
2) Make xfrm migration namespace aware. From Fan Du.
3) Make the xfrm state and policy locks namespace aware. From Fan Du.
4) Remove ancient sleeping when the SA is in acquire state,
we now queue packets to the policy instead. This replaces the
sleeping code.
5) Remove FLOWI_FLAG_CAN_SLEEP. This was used to notify xfrm about the
posibility to sleep. The sleeping code is gone, so remove it.
6) Check user specified spi for IPComp. Thr spi for IPcomp is only
16 bit wide, so check for a valid value. From Fan Du.
7) Export verify_userspi_info to check for valid user supplied spi ranges
with pfkey and netlink. From Fan Du.
8) RFC3173 states that if the total size of a compressed payload and the IPComp
header is not smaller than the size of the original payload, the IP datagram
must be sent in the original non-compressed form. These packets are dropped
by the inbound policy check because they are not transformed. Document the need
to set 'level use' for IPcomp to receive such packets anyway. From Fan Du.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
this is a pull request of four patches for net-next/master.
There is one patch by Markus Pargmann, which speeds up the c_can
driver, a patch by John Whitmore which updates the in tree
documentation. A patch by Jeff Kirsher which replaces the FSF's address
by a link and a patch by Alexander Shiyan which converts the mcp251x
driver to make use of managed resources.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This new mode discards all incoming fragmentation-needed notifications
as I guess was originally intended with this knob. To not break backward
compatibility too much, I only added a special case for mode 2 in the
receiving path.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/i40e/i40e_main.c
drivers/net/macvtap.c
Both minor merge hassles, simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed MAINTAINERS file to add Documentation/networking/can.txt to the list of
maintained files.
can.txt:
- Globally changed Socket CAN to SocketCAN
- Removed section 3.3 from the document
- Updated Section 7
- Corrected a few simple typos
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: John Whitmore <johnfwhitmore@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Create Documentation/networking/ipsec.txt to document IPsec
corner issues and other info, which will be useful when user
deploying IPsec.
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch significantly updates the BPF documentation and describes
its internal architecture, Linux extensions, and handling of the
kernel's BPF and JIT engine, plus documents how development can be
facilitated with the help of bpf_dbg, bpf_asm, bpf_jit_disasm.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are quite a lot of drivers touching a PHY device MII_BMCR
register to reset the PHY without taking care of:
1) ensuring that BMCR_RESET is cleared after a given timeout
2) the PHY state machine resuming to the proper state and re-applying
potentially changed settings such as auto-negotiation
Introduce phy_poll_reset() which will take care of polling the MII_BMCR
for the BMCR_RESET bit to be cleared after a given timeout or return a
timeout error code.
In order to make sure the PHY is in a correct state, phy_init_hw() first
issues a software reset through MII_BMCR and then applies any fixups.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a PACKET_QDISC_BYPASS socket option, that
allows for using a similar xmit() function as in pktgen instead
of taking the dev_queue_xmit() path. This can be very useful when
PF_PACKET applications are required to be used in a similar
scenario as pktgen, but with full, flexible packet payload that
needs to be provided, for example.
On default, nothing changes in behaviour for normal PF_PACKET
TX users, so everything stays as is for applications. New users,
however, can now set PACKET_QDISC_BYPASS if needed to prevent
own packets from i) reentering packet_rcv() and ii) to directly
push the frame to the driver.
In doing so we can increase pps (here 64 byte packets) for
PF_PACKET a bit:
# CPUs -- QDISC_BYPASS -- qdisc path -- qdisc path[**]
1 CPU == 1,509,628 pps -- 1,208,708 -- 1,247,436
2 CPUs == 3,198,659 pps -- 2,536,012 -- 1,605,779
3 CPUs == 4,787,992 pps -- 3,788,740 -- 1,735,610
4 CPUs == 6,173,956 pps -- 4,907,799 -- 1,909,114
5 CPUs == 7,495,676 pps -- 5,956,499 -- 2,014,422
6 CPUs == 9,001,496 pps -- 7,145,064 -- 2,155,261
7 CPUs == 10,229,776 pps -- 8,190,596 -- 2,220,619
8 CPUs == 11,040,732 pps -- 9,188,544 -- 2,241,879
9 CPUs == 12,009,076 pps -- 10,275,936 -- 2,068,447
10 CPUs == 11,380,052 pps -- 11,265,337 -- 1,578,689
11 CPUs == 11,672,676 pps -- 11,845,344 -- 1,297,412
[...]
20 CPUs == 11,363,192 pps -- 11,014,933 -- 1,245,081
[**]: qdisc path with packet_rcv(), how probably most people
seem to use it (hopefully not anymore if not needed)
The test was done using a modified trafgen, sending a simple
static 64 bytes packet, on all CPUs. The trick in the fast
"qdisc path" case, is to avoid reentering packet_rcv() by
setting the RAW socket protocol to zero, like:
socket(PF_PACKET, SOCK_RAW, 0);
Tradeoffs are documented as well in this patch, clearly, if
queues are busy, we will drop more packets, tc disciplines are
ignored, and these packets are not visible to taps anymore. For
a pktgen like scenario, we argue that this is acceptable.
The pointer to the xmit function has been placed in packet
socket structure hole between cached_dev and prot_hook that
is hot anyway as we're working on cached_dev in each send path.
Done in joint work together with Jesper Dangaard Brouer.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge 'net' into 'net-next' to get the AF_PACKET bug fix that
Daniel's direct transmit changes depend upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e40526cb20 introduced a cached dev pointer, that gets
hooked into register_prot_hook(), __unregister_prot_hook() to
update the device used for the send path.
We need to fix this up, as otherwise this will not work with
sockets created with protocol = 0, plus with sll_protocol = 0
passed via sockaddr_ll when doing the bind.
So instead, assign the pointer directly. The compiler can inline
these helper functions automagically.
While at it, also assume the cached dev fast-path as likely(),
and document this variant of socket creation as it seems it is
not widely used (seems not even the author of TX_RING was aware
of that in his reference example [1]). Tested with reproducer
from e40526cb20.
[1] http://wiki.ipxwarzone.com/index.php5?title=Linux_packet_mmap#Example
Fixes: e40526cb20 ("packet: fix use after free race in send path when dev is released")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Tested-by: Salam Noureddine <noureddine@aristanetworks.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Please pull this batch of updates intended for the 3.14 stream...
For the mac80211 bits, Johannes says:
"I have various improvements/cleanups/fixes all over, but the shortlog
shows that Luis's regulatory work and mesh work from the cozybit folks
are the biggest ones, along with the CSA fixes."
Along with that, we have big batches of updates to brcmfmac, rtlwifi,
and ath9k. There are updates to wcn36xx, rt2x00, and a handful of
others as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With the introduction of TCP Small Queues, TSO auto sizing, and TCP
pacing, we can implement Automatic Corking in the kernel, to help
applications doing small write()/sendmsg() to TCP sockets.
Idea is to change tcp_push() to check if the current skb payload is
under skb optimal size (a multiple of MSS bytes)
If under 'size_goal', and at least one packet is still in Qdisc or
NIC TX queues, set the TCP Small Queue Throttled bit, so that the push
will be delayed up to TX completion time.
This delay might allow the application to coalesce more bytes
in the skb in following write()/sendmsg()/sendfile() system calls.
The exact duration of the delay is depending on the dynamics
of the system, and might be zero if no packet for this flow
is actually held in Qdisc or NIC TX ring.
Using FQ/pacing is a way to increase the probability of
autocorking being triggered.
Add a new sysctl (/proc/sys/net/ipv4/tcp_autocorking) to control
this feature and default it to 1 (enabled)
Add a new SNMP counter : nstat -a | grep TcpExtTCPAutoCorking
This counter is incremented every time we detected skb was under used
and its flush was deferred.
Tested:
Interesting effects when using line buffered commands under ssh.
Excellent performance results in term of cpu usage and total throughput.
lpq83:~# echo 1 >/proc/sys/net/ipv4/tcp_autocorking
lpq83:~# perf stat ./super_netperf 4 -t TCP_STREAM -H lpq84 -- -m 128
9410.39
Performance counter stats for './super_netperf 4 -t TCP_STREAM -H lpq84 -- -m 128':
35209.439626 task-clock # 2.901 CPUs utilized
2,294 context-switches # 0.065 K/sec
101 CPU-migrations # 0.003 K/sec
4,079 page-faults # 0.116 K/sec
97,923,241,298 cycles # 2.781 GHz [83.31%]
51,832,908,236 stalled-cycles-frontend # 52.93% frontend cycles idle [83.30%]
25,697,986,603 stalled-cycles-backend # 26.24% backend cycles idle [66.70%]
102,225,978,536 instructions # 1.04 insns per cycle
# 0.51 stalled cycles per insn [83.38%]
18,657,696,819 branches # 529.906 M/sec [83.29%]
91,679,646 branch-misses # 0.49% of all branches [83.40%]
12.136204899 seconds time elapsed
lpq83:~# echo 0 >/proc/sys/net/ipv4/tcp_autocorking
lpq83:~# perf stat ./super_netperf 4 -t TCP_STREAM -H lpq84 -- -m 128
6624.89
Performance counter stats for './super_netperf 4 -t TCP_STREAM -H lpq84 -- -m 128':
40045.864494 task-clock # 3.301 CPUs utilized
171 context-switches # 0.004 K/sec
53 CPU-migrations # 0.001 K/sec
4,080 page-faults # 0.102 K/sec
111,340,458,645 cycles # 2.780 GHz [83.34%]
61,778,039,277 stalled-cycles-frontend # 55.49% frontend cycles idle [83.31%]
29,295,522,759 stalled-cycles-backend # 26.31% backend cycles idle [66.67%]
108,654,349,355 instructions # 0.98 insns per cycle
# 0.57 stalled cycles per insn [83.34%]
19,552,170,748 branches # 488.244 M/sec [83.34%]
157,875,417 branch-misses # 0.81% of all branches [83.34%]
12.130267788 seconds time elapsed
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These two flags are used for the same purpose, just
combine them into a no-ir flag to annotate no initiating
radiation is allowed.
Old userspace sending either flag will have it treated as
the no-ir flag. To be considerate to older userspace we
also send both the no-ir flag and the old no-ibss flags.
Newer userspace will have to be aware of older kernels.
Update all places in the tree using these flags with the
following semantic patch:
@@
@@
-NL80211_RRF_PASSIVE_SCAN
+NL80211_RRF_NO_IR
@@
@@
-NL80211_RRF_NO_IBSS
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_PASSIVE_SCAN
+IEEE80211_CHAN_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IBSS
+IEEE80211_CHAN_NO_IR
@@
@@
-NL80211_RRF_NO_IR | NL80211_RRF_NO_IR
+NL80211_RRF_NO_IR
@@
@@
-IEEE80211_CHAN_NO_IR | IEEE80211_CHAN_NO_IR
+IEEE80211_CHAN_NO_IR
@@
@@
-(NL80211_RRF_NO_IR)
+NL80211_RRF_NO_IR
@@
@@
-(IEEE80211_CHAN_NO_IR)
+IEEE80211_CHAN_NO_IR
Along with some hand-optimisations in documentation, to
remove duplicates and to fix some indentation.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[do all the driver updates in one go]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
SIOCSHWTSTAMP returns the real configuration to the application
using it, but there is currently no way for any other
application to find out the configuration non-destructively.
Add a new ioctl for this, making it unprivileged.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
After commit c9eeec26e3 ("tcp: TSQ can use a dynamic limit"), several
users reported throughput regressions, notably on mvneta and wifi
adapters.
802.11 AMPDU requires a fair amount of queueing to be effective.
This patch partially reverts the change done in tcp_write_xmit()
so that the minimal amount is sysctl_tcp_limit_output_bytes.
It also remove the use of this sysctl while building skb stored
in write queue, as TSO autosizing does the right thing anyway.
Users with well behaving NICS and correct qdisc (like sch_fq),
can then lower the default sysctl_tcp_limit_output_bytes value from
128KB to 8KB.
This new usage of sysctl_tcp_limit_output_bytes permits each driver
authors to check how their driver performs when/if the value is set
to a minimum of 4KB.
Normally, line rate for a single TCP flow should be possible,
but some drivers rely on timers to perform TX completion and
too long TX completion delays prevent reaching full throughput.
Fixes: c9eeec26e3 ("tcp: TSQ can use a dynamic limit")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Sujith Manoharan <sujith@msujith.org>
Reported-by: Arnaud Ebalard <arno@natisbad.org>
Tested-by: Sujith Manoharan <sujith@msujith.org>
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new documentation for the packets_per_slave option available
for balance-rr mode.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
here's a pull request for net-next.
It includes a patch by Oliver Hartkopp et al. that adds documentation
for the broadcast manager to Documentation/networking/can.txt. Three
patches by me that clean up the netlink handling code in the CAN core.
And another patch that removes a not needed function from the ti_hecc
driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Slow start now increases cwnd by 1 if an ACK acknowledges some packets,
regardless the number of packets. Consequently slow start performance
is highly dependent on the degree of the stretch ACKs caused by
receiver or network ACK compression mechanisms (e.g., delayed-ACK,
GRO, etc). But slow start algorithm is to send twice the amount of
packets of packets left so it should process a stretch ACK of degree
N as if N ACKs of degree 1, then exits when cwnd exceeds ssthresh. A
follow up patch will use the remainder of the N (if greater than 1)
to adjust cwnd in the congestion avoidance phase.
In addition this patch retires the experimental limited slow start
(LSS) feature. LSS has multiple drawbacks but questionable benefit. The
fractional cwnd increase in LSS requires a loop in slow start even
though it's rarely used. Configuring such an increase step via a global
sysctl on different BDPS seems hard. Finally and most importantly the
slow start overshoot concern is now better covered by the Hybrid slow
start (hystart) enabled by default.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Applications have started to use Fast Open (e.g., Chrome browser has
such an optional flag) and the feature has gone through several
generations of kernels since 3.7 with many real network tests. It's
time to enable this flag by default for applications to test more
conveniently and extensively.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be.h
drivers/net/netconsole.c
net/bridge/br_private.h
Three mostly trivial conflicts.
The net/bridge/br_private.h conflict was a function signature (argument
addition) change overlapping with the extern removals from Joe Perches.
In drivers/net/netconsole.c we had one change adjusting a printk message
whilst another changed "printk(KERN_INFO" into "pr_info(".
Lastly, the emulex change was a new inline function addition overlapping
with Joe Perches's extern removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
Joby Poriyath provided a xen-netback patch to reduce the size of
xenvif structure as some netdev allocation could fail under
memory pressure/fragmentation.
This patch is handling the problem at the core level, allowing
any netdev structures to use vmalloc() if kmalloc() failed.
As vmalloc() adds overhead on a critical network path, add __GFP_REPEAT
to kzalloc() flags to do this fallback only when really needed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Joby Poriyath <joby.poriyath@citrix.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds documentation about the broadcast manager. It's based on Brian
Thorne's initial patch http://marc.info/?l=linux-can&m=138119382015496&w=2 and
Daniele Venzano's work http://brownhat.org/docs/socketcan.html .
Signed-off-by: Brian Thorne <hardbyte@gmail.com>
Cc: Daniele Venzano <linux@brownhat.org>
Cc: Andre Naujoks <nautsch2@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Correct spelling typo in Documentation/networking
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Various typo fixes to netdev-FAQ.txt:
- capitalize Linux
- hyphenate dual-word adjectives
- minor punctuation fixes
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My university will stop email service for alumni in january 2014, please
use my new e-mail address instead.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
This is replaced by a userspace program, we don't need this
functionality to bloat the kernel.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Add new documentation for encap2+3 and encap3+4, also update the formula
for the old modes due to the changes.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
running bonding in ALB mode requires that learning packets be sent periodically,
so that the switch knows where to send responding traffic. However, depending
on switch configuration, there may not be any need to send traffic at the
default rate of 3 packets per second, which represents little more than wasted
data. Allow the ALB learning packet interval to be made configurable via sysfs
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Acked-by: Veaceslav Falico <vfalico@redhat.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the changes for Kconfig, i40e.txt, MAINTAINERS, Kbuild
and new i40e/Makefile to build i40e with the kernel.
New driver build option is CONFIG_I40E
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
CC: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
CC: e1000-devel@lists.sourceforge.net
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Document force_mld_version parameter in ip-sysctl.txt.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some synopsys ip implementation doesn't support DMA store and forward mode,
such as BF60x. So, set force_thresh_dma_mode to use DMA thresholds only.
Update document and devicetree as well.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update documentation to add fanout policies that are available.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After hearing many people over past years complaining against TSO being
bursty or even buggy, we are proud to present automatic sizing of TSO
packets.
One part of the problem is that tcp_tso_should_defer() uses an heuristic
relying on upcoming ACKS instead of a timer, but more generally, having
big TSO packets makes little sense for low rates, as it tends to create
micro bursts on the network, and general consensus is to reduce the
buffering amount.
This patch introduces a per socket sk_pacing_rate, that approximates
the current sending rate, and allows us to size the TSO packets so
that we try to send one packet every ms.
This field could be set by other transports.
Patch has no impact for high speed flows, where having large TSO packets
makes sense to reach line rate.
For other flows, this helps better packet scheduling and ACK clocking.
This patch increases performance of TCP flows in lossy environments.
A new sysctl (tcp_min_tso_segs) is added, to specify the
minimal size of a TSO packet (default being 2).
A follow-up patch will provide a new packet scheduler (FQ), using
sk_pacing_rate as an input to perform optional per flow pacing.
This explains why we chose to set sk_pacing_rate to twice the current
rate, allowing 'slow start' ramp up.
sk_pacing_rate = 2 * cwnd * mss / srtt
v2: Neal Cardwell reported a suspect deferring of last two segments on
initial write of 10 MSS, I had to change tcp_tso_should_defer() to take
into account tp->xmit_size_goal_segs
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Van Jacobson <vanj@google.com>
Cc: Tom Herbert <therbert@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements RFC6980: Drop fragmented ndisc packets by
default. If a fragmented ndisc packet is received the user is informed
that it is possible to disable the check.
Cc: Fernando Gont <fernando@gont.com.ar>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Gross says:
====================
A number of significant new features and optimizations for net-next/3.12.
Highlights are:
* "Megaflows", an optimization that allows userspace to specify which
flow fields were used to compute the results of the flow lookup.
This allows for a major reduction in flow setups (the major
performance bottleneck in Open vSwitch) without reducing flexibility.
* Converting netlink dump operations to use RCU, allowing for
additional parallelism in userspace.
* Matching and modifying SCTP protocol fields.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates the documentation to the Intel wired LAN drivers.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
