With the generic Broadcom Bluetooth support module, it is possible to
turn support for firmware and patchram download into an optional
feature.
To keep backwards compatibility with previous kernel configurations,
the new option defaults to enabled.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The new Broadcom Bluetooth support module provides generic functionality
for changing and checking the Bluetooth device address. Use these new
features instead of keeping a duplicate in the driver.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For all modern Bluetooth USB devices from Broadcom it makes a lot more
sense to use USB_VENDOR_AND_INTERFACE_INFO instead of manually adding
USB_DEVICE for each one of them. There are already interface entries
for these vendors and so just remove the duplicate device entries.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For the Apple Bluetooth devices that are Broadcom based, it makes sense
to read the chip information. It is a single HCI command and might help
gathering more information about these devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Broadcom devices expose their chip id via Read Verbose Config
Version Info command. While this information is not used at the
moment, it might be useful for debugging purposes and so read it
before patching the firmware. This makes it show up in dmesg and
HCI traces taken for the system.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
CSR controllers can do both LE scan and BR/EDR inquiry at once.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Intel controllers can do both LE scan and BR/EDR inquiry at once.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Atheros controllers can do both LE scan and BR/EDR inquiry at once.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Johan Hedberg says:
====================
Here's another set of Bluetooth & ieee802154 patches intended for 4.1:
- Added support for QCA ROME chipset family in the btusb driver
- at86rf230 driver fixes & cleanups
- ieee802154 cleanups
- Refactoring of Bluetooth mgmt API to allow new users
- New setting for static Bluetooth address exposed to user space
- Refactoring of hci_dev flags to remove limit of 32
- Remove unnecessary fast-connectable setting usage restrictions
- Fix behavior to be consistent when trying to pair already paired device
- Service discovery corner-case fixes
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple codepaths duplicate some simple code to read and
sanity-check local version information. Before I add a couple more
such codepaths, add a helper to reduce duplication.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
While qca_device_info is not coming from outside communication,
no reason to use specific endian type inside and fix the wrong
version comparison on big-endian platform.
Signed-off-by: Ben Young Tae Kim <ytkim@qca.qualcomm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of chipset does not allow to send a patch or config files through
HCI VS channel at early stage as well as they don't support to send
USB patch files to other channel except USB bulk path.
New callback added is for initialization of BT controller through USB
Signed-off-by: Ben Young Tae Kim <ytkim@qca.qualcomm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Broadcom firmware files are named with firmware version information
encoded into lmp_subver field. So BCM20702B0_002.001.014.0527.0607.hex
would be represented by 0x410e. To allow for an easier decoding of the
actual firmware names, provide an internal table that does the mapping
and request the firmware file by name.
Bluetooth: hci0: BCM20702B0 (002.001.014) build 0607
Now the complicated encoding of lmp_subver will be decoded and turned
into the name and firmware version information from the firmware files.
The previous attempt of using udev->product failed badly since it never
contains any matching entry to the actual hardware or firmware files
distributed by Broadcom in their Windows drivers. It is even worse since
it can change depending on if the internal bootstrapping happened before
the USB bus enumeration or after. This caused many race conditions.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds the device shutdown routine for Intel Bluetooth device.
Some platforms have BT LED issue with Intel Bluetooth device that BT LED goes
off 5 seconds after BT is turned off
For Intel Bluetooth device, the BT LED is turned off when:
- there is no active connection or radio activity
- USB is suspend
So, when the BT is turned off, it takes 5 seconds because USB suspend timeone
is 5 seconds by default. And if the USB suspend is not enabled, BT LED won't be
turned off.
To fix this issue, recently Intel Bluetooth firmware patch had been submitted
to turn off the BT LED immediately by the vendor specific command(0xFC3F). And
this patch sends this command to the device before closing the device.
For backward compatibility of this command with old firmware, this command was
supported before, but it behaves same as HCI_RESET internally. So, it won't be
the problem even if the system doesn't have the latest firmware patch.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There's now a proper wait_on_bit_timeout() API in linux/wait.h so we can
remove our own copy from btusb.c. Our copy had the task state and
timeout variables swapped so the patch also changes their order.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Intel Snowfield Peak Bluetooth controllers use a strict scanning
filter policy that filters based on Bluetooth device addresses and
not on RSSI.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Bluetooth controllers from Intel use a strict scanning filter
policy that filters based on Bluetooth device addresses and not on
RSSI. So tell the core about this.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The wait_on_bit_timeout() is a simpler and race-free way of waiting for
a bit to be cleared than the current code in btusb.c. This patch updates
the code to use the helper function (its btusb copy - to be later
updated to use a global one).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The test for BTUSB_DOWNLOADING must be after adding to the wait queue
and setting the TASK_INTERRUPTIBLE state. Otherwise the flag may get
cleared after we test for it and we end up getting a timeout since
schedule_timeout() waits for the full duration. This patch uses a
wait_on_bit_timeout() + wake_up_bit(). To perform the task both
race-free as well as in a much simpler way.
Since there's no global wait_on_bit_timeout() helper yet (even though
all the building blocks for it are in place) this patch creates a
temporary local btusb copy of it until the global one has made it to
upstream trees.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In general all Intel Bluetooth devices support retrieving of additional
exception information. However for older generations including Wilkens
Peak and Stone Peak it is not as simple. So for now only enable the
Intel specific error handling for Snowfield Peak and later devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Bluetooth controllers from Atheros use a strict scanning filter
policy that filters based on Bluetooth device addresses and not on
RSSI. So tell the core about this.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Bluetooth HCI transport specification for USB device defines on how
a standard AMP controller is identified and operated. This patch adds
the needed handling to hook it up to the Bluetooth stack.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Intel Bluetooth devices use the generic USB device/interface class
descriptors that are assigned to Bluetooth H:2 conforming transports.
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
However newer chips have a bootloader stage and require firmware to
be loaded before they are functional. To avoid any confusion for the
users, just ignore unknown Intel Bluetooth devices.
All the released Intel Bluetooth devices have an entry in the device
table identifying their setup and support requirements. The advantage
here is that older kernel can be booted with newer devices without
causing any disturbance.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
New entries to the USB blacklist/quirk device table should be sorted
by USB vendor id. Fix the recent entry fro Marvell devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Intel Bluetooth controllers can provide an additional exception
info string when a hardware error event occurs. The core will now
call hdev->hw_error to let the driver read out this information.
This change will cause a reset of the hardware to bring it back
into functional state and then read the Intel exception info
string and print it along with the error information.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The btusb_disconnect() callback calls hci_unregister_dev() which in turn
calls btusb_close() if the HCI device is powered. The btusb_close()
function in turn will call btusb_free_frags(). It's therefore
unnecessary to have another call to btusb_free_frags() in the
btusb_disconnect() function. Besides the redundancy the second call
seems to also cause some strange stability issues which this patch then
also fixes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When loading the Intel firmware it can happen that the firmware loading
complete vendor event arrives before the command complete event for the
last firmware fragment.
< HCI Command: Vendor (0x3f|0x0009) plen 7
01 02 fc 03 00 00 00
> HCI Event: Vendor (0xff) plen 5
06 00 00 00 00
> HCI Event: Command Complete (0x0e) plen 4
Vendor (0x3f|0x0009) ncmd 31
Status: Success (0x00)
This is mainly caused by the fact that the vendor command and its
command complete event are transported over the bulk endpoints. The
firmware loading complete event however is send over the interrupt
endpoint. So with just bad timing one event arrives before the other.
Currently the code does not account for it. There are precautions for
receiving firmware loading complete event quickly, but not for receiving
it before the command complete.
Introduce an extra flag that tracks when the firmware sending has
completed from the driver point of view and track the completion of
the firmware loading procedure with a different flag. That way the
wakeup can be handled properly.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some new upcoming drivers need to process HCI events or take extra
actions based on them before handing the event to the Bluetooth core
for processing. The new recv_event callback allows exactly such an
internal behavior.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Silicon Wave based devices do support Inquiry Result with RSSI and
so let the core know to enable them.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Roper Class 1 Bluetooth Dongle is another device that claims to
support Bluetooth 1.2 specification, but does not support the HCI
command for reading the local supported commands.
< HCI Command: Read Local Version Information (0x04|0x0001) plen 0
> HCI Event: Command Complete (0x0e) plen 12
Read Local Version Information (0x04|0x0001) ncmd 1
status 0x00
HCI Version: 1.2 (0x2) HCI Revision: 0x0
LMP Version: 1.2 (0x2) LMP Subversion: 0x757
Manufacturer: Silicon Wave (11)
It clearly claims Bluetooth 1.2 support and in that regard has the
same issue as the AVM BlueFritz! USB devices (Silicon Wave based),
but the HCI Read Local Supported Commands command fails.
< HCI Command: Read Local Supported Commands (0x04|0x0002) plen 0
> HCI Event: Command Status (0x0f) plen 4
Read Local Supported Commands (0x04|0x0002) status 0x01 ncmd 1
Error: Unknown HCI Command
Use the HCI_QUIRK_BROKEN_LOCAL_COMMANDS quirk for these devices and
the failing command will be skipped.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The AVM BlueFritz! 2.0 USB dongles do not support the HCI command for
reading the local supported commands. So set this quirk to let the
core know about it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Set hdev->set_bdaddr handler for ath3012. It sends the vendor specific HCI
command to change the public address. The change doesn't persist across
power cycle.
Signed-off-by: Toshi Kikuchi <toshik@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some vendors require special handling of the rx data from the USB
bulk endpoints. For that case provide an internal callback that
can overwrite it with a custom receive function.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Bluetooth controllers from Broadcom use a strict scanning filter
policy that filters based on Bluetooth device addresses and not on
RSSI. So tell the core about this.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
