Move USB PHYs to a standard arrays for Exynos EHCI/OHCI devices. This
resolves the conflict between Exynos EHCI/OHCI sub-nodes and generic USB
device bindings. Once the Exynos EHCI/OHCI sub-nodes are removed, the
boards can finally provide sub-nodes for the USB devices using generic USB
device bindings.
Suggested-by: Måns Rullgård <mans@mansr.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20190726081453.9456-4-m.szyprowski@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the ADC from exynos5420.dtsi to a shared file between Exynos5410 and
Exynos542x: exynos54xx.dtsi. Enable the ADC on Odroid XU board.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The ARM PMU and ARM architected timer nodes are part of ARM CPU design
therefore they should not be inside the soc node. This also fixes DTC
W=1 warnings like:
arch/arm/boot/dts/exynos3250.dtsi:106.21-135.5:
Warning (simple_bus_reg): /soc/fixed-rate-clocks: missing or empty reg/ranges property
arch/arm/boot/dts/exynos3250.dtsi:676.7-680.5:
Warning (simple_bus_reg): /soc/pmu: missing or empty reg/ranges property
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Enable support for ARM Performance Monitoring Units available in Cortex-A7
and Cortex-A15 CPU cores for Exynos54xx SoCs (5410, 5420 and 5422/5800).
The PMUs interrupts are defined in the common exynos54xx.dtsi device tree,
but the PMUs are enabled and have their interrupt CPU affinity defined
next to each SoC's cpus node.
Tested with perf on Odroid XU4 (Exynos5422):
armv7_cortex_a7 PMU driver: 5 counters available
armv7_cortex_a15 PMU driver: 7 counters available
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Marian Mihailescu <mihailescu2m@gmail.com>
Signed-off-by: Willy Wolff <willy.mh.wolff@gmail.com>
[mszyprow: reordered nodes according to krzk request, fixed typos]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Move Security Subsystem nodes common for Exynos5250 and Exynos54xx
to exynos5.dtsi to avoid duplication.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Pull "Samsung DTS ARM changes for 4.15" from Krzysztof Kozłowski:
1. Add new board: Hardkernel Odroid HC1.
2. Fix incomplete Odroid-XU3/4 thermal-zones definition leading to
possible overheat if first pair of A7+A15 cores is idle but rest of
CPUs are busy.
3. Add capacity-dmips-mhz properties for CPUs of octa-core SoCs.
4. Add power button to Odroid XU3/4.
5. Improvements in Gscaler, HDMI and Mixer blocks on Exynos5.
6. Add suspend quirk to DWC3 USB controller to fix enumeration of
SuperSpeed devices on Odroid XU4.
7. Add HDMI and MHL to Trats2.
8. Cleanups (redundant properties and nodes).
* tag 'samsung-dt-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
dt-bindings: samsung: Document binding for new Odroid HC1 board
ARM: dts: exynos: Add HDMI and Sil9234 to Trats2 board
ARM: dts: exynos: Add support for Hardkernel's Odroid HC1 board
ARM: dts: exynos: Move audio clocks configuration to odroidxu3-audio.dtsi
ARM: dts: exynos: Add dwc3 SUSPHY quirk
ARM: dts: exynos: Add status property to Exynos 542x Mixer nodes
ARM: dts: exynos: Add status property to Exynos 5250 HDMI and Mixer nodes
ARM: dts: exynos: Cleanup HDMI DCC definitions on Exynos5250 and Exynos542x boards
ARM: dts: exynos: Move HDMI PHY node from boards to exynos5250.dtsi
ARM: dts: exynos: Use specific compatibles for proper Gscaler limits on Exynos5250 and Exynos5420
ARM: dts: exynos: Remove redundant interrupt properties in gpio-keys on Odroid boards
ARM: dts: exynos: Add power button for Odroid XU3/4
ARM: dts: exynos: Remove the display-timing and delay from Rinato
ARM: dts: exynos: add exynos5422 cpu capacity-dmips-mhz information
ARM: dts: exynos: add exynos5420 cpu capacity-dmips-mhz information
ARM: dts: exynos: fix incomplete Odroid-XU3/4 thermal-zones definition
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm/boot/dts -type -f -name '*.dts*'
Dropped changes to ARM, Ltd. boards LED nodes and manually fixed up some
occurrences of uppercase hex.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Odroid XU4 board does not enumerate SuperSpeed devices.
This patch makes exynos5 series chips use USB SUSPHY quirk,
which solves the problem.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Replace hard-coded values of type of GIC interrupt and its flags with
respective macros from header to increase code readability.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Interrupt of type IRQ_TYPE_NONE is not allowed for GIC interrupts and
generates an error:
genirq: Setting trigger mode 0 for irq 16 failed (gic_set_type+0x0/0x68)
The GIC requires shared interrupts to be edge rising or level high.
Platform declares support for both. Arbitrarily choose level high
everywhere hoping it will work on each platform.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Alban Browaeys <alban.browaeys@gmail.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Move watchdog and Security SubSystem nodes from exynos5420.dtsi to file
shared with Exynos5410 and configure the clocks on the latter.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
On Exynos5410 the SPI interrupt for second USB DWC3 (called DRD: Dual
Role Device) is different - 200 instead of 73.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The USI/HSI2C nodes can be mostly shared between Exynos5420 and
Exynos5410 so move them to common DTSI.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Move USB 3.0 DWC and 2.0 EHCI/OHCI nodes from exynos5420.dtsi to
exynos54xx.dtsi common for entire family. For Exynos542x/5800 this
should not have functional impact but for Exynos5410 this effectively
adds USB support.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
The Exynos5410/542x/5800 are very similar designs. Create a new
DTSI with common nodes to remove DTS duplication. Although currently
only MCT and SysRAM are shared but in future more nodes will be added to
the common file.
The patch should not have functional impact.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
