Fixed compilation errors in case of non-KEXEC kernel
Rearranging code so that crashk_res gets updated.
- crashk_res is updated after mips_parse_crashkernel(),
after resource_init(), which is after arch_mem_init().
- The reserved memory is actually treated as Usable memory,
Unless we load the crash kernel, everything works.
Signed-off-by: Prem Mallappa <pmallappa@caviumnetworks.com>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/5805/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This change corrects DECstation HRT calibration, by removing the following
bugs:
1. Calibration period selection -- HZ / 10 has been chosen, however on
DECstation computers, HZ never divides by 10, as the choice for HZ is
among 128, 256 and 1024. The choice therefore results in a systematic
calibration error, e.g. 6.25% for the usual choice of 128 for HZ:
128 / 10 * 10 = 120
(128 - 120) / 128 -> 6.25%
The change therefore makes calibration use HZ / 8 that is always
accurate for the HZ values available, getting rid of the systematic
error.
2. Calibration starting point synchronisation -- the duration of a number
of intervals between DS1287A periodic interrupt assertions is measured,
however code does not ensure at the beginning that the interrupt has
not been previously asserted. This results in a variable error of e.g.
up to another 6.25% for the period of HZ / 8 (8.(3)% with the original
HZ / 10 period) and the usual choice of 128 for HZ:
1 / 16 -> 6.25%
1 / 12 -> 8.(3)%
The change therefore adds an initial call to ds1287_timer_state that
clears any previous periodic interrupt pending.
The same issue applies to both I/O ASIC counter and R4k CP0 timer
calibration on DECstation systems as similar code is used in both cases
and both pieces of code are covered by this fix.
On an R3400 test system used this fix results in a change of the I/O ASIC
clock frequency reported from values like:
I/O ASIC clock frequency 23185830Hz
to:
I/O ASIC clock frequency 24999288Hz
removing the miscalculation by 6.25% from the systematic error and (for
the individual sample provided) a further 1.00% from the variable error,
accordingly. The nominal I/O ASIC clock frequency is 25MHz on this
system.
Here's another result, with the fix applied, from a system that has both
HRTs available (using an R4400 at 60MHz nominal):
MIPS counter frequency 59999328Hz
I/O ASIC clock frequency 24999432Hz
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5807/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The kbldr.h header file required for this was neither committed in the
original submission in a3a0f8c8ed
"MIPS: PowerTV: Base files for Cisco PowerTV platform"
nor was it ever present in the git tree so this option never worked.
Fixes the following build problem:
arch/mips/powertv/reset.c:25:36: fatal error: asm/mach-powertv/kbldr.h: No such
file or directory
compilation terminated.
Cc: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: David VomLehn <dvomlehn@cisco.com>
Patchwork: https://patchwork.linux-mips.org/patch/5801/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The NR_CPUS_DEFAULT_1 introduced as an aid for the QEMU
platform in 72ede9b189
"[MIPS] Qemu: Fix Symmetric Uniprocessor support"
which was later removed in
302922e5f6
"[MIPS] Qemu: Remove platform."
On certain randconfigs it may happen for NR_CPUS to have an
empty value because not all SMP platforms select a suitable
NR_CPUS_DEFAULT_* value. We fix this by restoring the range
of NR_CPUS to 2..64 and drop the NR_CPUS_DEFAULT_{1,2} symbols.
The first one is no longer used and the latter is not needed since
NR_CPUS=2 is now the default value.
Fixes the following problem on a randconfig:
.config:164:warning: symbol value '' invalid for NR_CPUS
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5747/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The jmr3927_vec txx9_board_vec struct is defined in
txx9/jmr3927/setup.c which is only built if
CONFIG_TOSHIBA_JMR3927 is selected. This patch fixes the following
build problem:
arch/mips/txx9/generic/setup.c: In function 'select_board':
arch/mips/txx9/generic/setup.c:354:20: error:
'jmr3927_vec' undeclared (first use in this function)
arch/mips/txx9/generic/setup.c:354:20: note: each undeclared
identifier is reported only once for each function it appears in
make[3]: *** [arch/mips/txx9/generic/setup.o] Error 1
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5713/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The pci.c code depends on symbols which are only visible
if CONFIG_PCI is selected.
Also fixes the following problem on loongson allnoconfig:
arch/mips/built-in.o: In function `pcibios_init':
pci.c:(.init.text+0x528):
undefined reference to `register_pci_controller'
arch/mips/built-in.o:(.data+0xc):
undefined reference to `loongson_pci_ops'
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5584/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Dynamic function tracing was not working on MIPS. When doing dynamic
tracing, the tracer attempts to match up the passed in address with
the one the compiler creates in the mcount tables. The MIPS code was
passing in the return address from the tracing function call, but the
compiler tables were the address of the function call. So they
wouldn't match.
Just subtracting 8 from the return address will give the address of
the function call. Easy enough.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
[david.daney@cavium.com: Adjusted code comment and patch Subject.]
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/5592/
This is a fix for a bug introduced with commit
447cdf2628, submitted as archived here:
http://www.linux-mips.org/cgi-bin/mesg.cgi?a=linux-mips&i=20080312235002.c717dde3.yoichi_yuasa%40tripeaks.co.jp
regrettably with no further explanation.
The issue is with the CP0 Count register read erratum present on R4000 and
some R4400 processors. If this erratum is present, then a read from this
register that happens around the time it reaches the value stored in the
CP0 Compare register causes a CP0 timer interrupt that is supposed to
happen when the values in the two registers match to be missed. The
implication for the chips affected is the CP0 timer can be used either as
a source of a timer interrupt (a clock event) or as a source of a
high-resolution counter (a clock source), but not both at a time.
The erratum does not affect timer interrupt operation itself, because in
this case the CP0 Count register is only read while the timer interrupt
has already been raised, while high-resolution counter references happen
at random times.
Additionally some systems apparently have issues with the timer interrupt
line being routed externally and not following the usual CP0 Count/Compare
semantics. In this case we don't want to use the R4k clock event.
We've meant to address the erratum and the timer interrupt routing issue
in time_init, however the commit referred to above broke our solution.
What we currently have is we enable the R4k clock source if the R4k clock
event initialization has succeeded (the timer is present and has no timer
interrupt routing issue) or there is no CP0 Count register read erratum.
Which gives the following boolean matrix:
clock event | count erratum => clock source
------------+---------------+--------------
0 | 0 | 1 (OK)
0 | 1 | 0 (bug!) -> no interference, could use
1 | 0 | 1 (OK)
1 | 1 | 1 (bug!) -> can't use, interference
What we want instead is to enable the R4k clock source if there is no CP0
Count register read erratum (obviously) or the R4k clock event
initialization has *failed* -- because in the latter case we won't be
using the timer interrupt anyway, so we don't care about any interference
CP0 Count reads might cause with the interrupt. This corresponds to the
following boolean matrix:
clock event | count erratum => clock source
------------+---------------+--------------
0 | 0 | 1
0 | 1 | 1
1 | 0 | 1
1 | 1 | 0
This is implemented here, effectively reverting the problematic commit,
and a short explanation is given next to code modified so that the
rationale is known to future readers and confusion is prevented from
happening here again.
It is worth noting that mips_clockevent_init returns 0 upon success while
cpu_has_mfc0_count_bug returns 0 upon failure. This is because the former
function returns an error code while the latter returns a boolean value.
To signify the difference I have therefore chosen to compare the result of
the former call explicitly against 0.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5799/
get_user_pages_fast() is missing cache flushes for MIPS platforms with
cache aliases. Filesystem failures observed with DirectIO operations due
to missing flush_anon_page() that use page coloring logic to work with
cache aliases. This fix falls through to take slow_irqon path that calls
get_user_pages() that has required logic for platforms where
cpu_has_dc_aliases is true.
[ralf@linux-mips.org: Explicity include <asm/cpu-features.h>.]
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/5469/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The branch emulation needs to handle the OCTEON BBIT instructions,
otherwise we get SIGILL instead of emulation.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5726/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The hardware interrupt routing for boot CPU != 0 is wrong because it
will route all the hardware interrupts to TP0 which is not the one we
booted from. Fix this by properly checking which boot CPU we are booting
from and updating the right interrupt mask for the boot CPU. This fixes
booting on BCM3368 with bmips_smp_emabled = 0.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: blogic@openwrt.org
Cc: jogo@openwrt.org
Cc: cernekee@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/5650/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The PNX8335_PCI_ETHERNET_INT macro is defined in
arch/mips/include/asm/mach-pnx833x/irq-mapping.h
only if CONFIG_SOC_PNX8335 is selected.
Fixes the following randconfig problem:
arch/mips/pnx833x/common/platform.c:210:12:
error: 'PNX8335_PIC_ETHERNET_INT' undeclared here
(not in a function)
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5585/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current BMIPS SMP code assumes that the slave CPU is physical and
logical CPU 1, but on some systems such as BCM3368, the slave CPU is
physical CPU0. Fix the code to read the physical CPU (thread ID) we are
running this code on, and adjust the relocation vector address based on
it. This allows bringing up the second CPU on BCM3368 for instance.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: cernekee@gmail.com
Cc: jogo@openwrt.org
Cc: blogic@openwrt.org
Patchwork: https://patchwork.linux-mips.org/patch/5621/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 4df715aa ("MIPS: BMIPS: support booting from physical CPU other
than 0") changed the interupt routing when we are booting from physical
CPU 0, but the settings are actually correct if we are booting from
physical CPU 0 or CPU 1. Revert that specific change.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: cernekee@gmail.com
Cc: jogo@openwrt.org
Cc: blogic@openwrt.org
Patchwork: https://patchwork.linux-mips.org/patch/5622/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 6e7582bf35
"MIPS: PowerTV: use free_reserved_area() to simplify code"
merged in 3.11-rc1, broke the build for the powertv defconfig with
the following build error:
arch/mips/powertv/asic/asic_devices.c: In function 'platform_release_memory':
arch/mips/powertv/asic/asic_devices.c:533:7: error: passing argument 1 of
'free_reserved_area' makes pointer from integer without a cast [-Werror]
The free_reserved_area() function expects a void * pointer for the start
address and a void * pointer for the end one.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5624/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If neither BCM47XX_SSD nor BCM47XX_BCMA is selected, then no
CPU type is available leading to build problems. We fix
this problem by using MIPS32r1 as the default CPU type for
the BCM47XX platform.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5618/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It wasn't until GCC 4.3 I believe that the __SIZEOF_*__ predefined macros
were added. The change below switches <uapi/asm/siginfo.h> to the
_MIPS_SZLONG macro so that compilation with e.g. GCC 4.1.2 succeeds.
This is a user API header so I think this is even more important, for
older userland support. The change adds an unsuccessful default too, to
catch any compiler configuration oddities.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5630/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix build error below:
arch/mips/include/asm/mach-generic/spaces.h:29:0: warning:
"UNCAC_BASE" redefined [enabled by default]
In file included from arch/mips/include/asm/addrspace.h:13:0,
from arch/mips/include/asm/barrier.h:11,
from arch/mips/include/asm/bitops.h:18,
from include/linux/bitops.h:22,
from include/linux/kernel.h:10,
from include/asm-generic/bug.h:13,
from arch/mips/include/asm/bug.h:41,
from include/linux/bug.h:4,
from include/linux/page-flags.h:9,
from kernel/bounds.c:9:
arch/mips/include/asm/mach-ar7/spaces.h:20:0: note: this is the
location of the previous definition
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5583/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS fixes from Ralf Baechle:
"MIPS fixes for 3.11. Half of then is for Netlogic the remainder
touches things across arch/mips.
Nothing really dramatic and by rc1 standards MIPS will be in fairly
good shape with this applied. Tested by building all MIPS defconfigs
of which with this pull request four platforms won't build. And yes,
it boots also on my favorite test systems"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: kvm: Kconfig: Drop HAVE_KVM dependency from VIRTUALIZATION
MIPS: Octeon: Fix DT pruning bug with pip ports
MIPS: KVM: Mark KVM_GUEST (T&E KVM) as BROKEN_ON_SMP
MIPS: tlbex: fix broken build in v3.11-rc1
MIPS: Netlogic: Add XLP PIC irqdomain
MIPS: Netlogic: Fix USB block's coherent DMA mask
MIPS: tlbex: Fix typo in r3000 tlb store handler
MIPS: BMIPS: Fix thinko to release slave TP from reset
MIPS: Delete dead invocation of exception_exit().
Virtualization does not always need KVM capabilities so drop the
dependency. The KVM symbol already depends on HAVE_KVM.
Fixes the following problem on a randconfig:
warning: (REMOTEPROC && RPMSG) selects VIRTUALIZATION which has unmet direct
dependencies (HAVE_KVM)
warning: (REMOTEPROC && RPMSG) selects VIRTUALIZATION which has unmet
direct dependencies (HAVE_KVM)
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5443/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
During the pruning of the device tree octeon_fdt_pip_iface() is called
for each PIP interface and every port up to the port count is removed
from the device tree. However, the count was set to the return value of
cvmx_helper_interface_enumerate() which doesn't actually return the
count but just returns zero on success. This effectively removed *all*
ports from the tree.
Use cvmx_helper_ports_on_interface() instead to fix this. This
successfully restores the 3 ports of my ERLite-3 and fixes the "kernel
assigns random MAC addresses" issue.
Signed-off-by: Faidon Liambotis <paravoid@debian.org>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5587/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make KVM_GUEST depend on BROKEN_ON_SMP so that it cannot be enabled with
SMP.
SMP kernels use ll/sc instructions for an atomic section in the tlb fill
handler, with a tlbp instruction contained in the middle. This cannot be
emulated with trap & emulate KVM because the tlbp instruction traps and
the eret to return to the guest code clears the LLbit which makes the sc
instruction always fail.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Sanjay Lal <sanjayl@kymasys.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5588/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 6ba045f9fb (MIPS: Move generated code
to .text for microMIPS) deleted tlbmiss_handler_setup_pgd_array, but some
references were not converted. Fix that to enable building a MIPS kernel.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Jayachandran C. <jchandra@broadcom.com>
Acked-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5589/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a legacy irq domain for the XLP PIC interrupts. This will be used
when interrupts are assigned from the device tree. This change is required
after commit c5cdc67 "irqdomain: Remove temporary MIPS workaround code".
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Cc: Jayachandran C <jchandra@broadcom.com>
Patchwork: https://patchwork.linux-mips.org/patch/5597/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The on-chip USB controller on Netlogic XLP does not suppport
DMA beyond 32-bit physical address. Set the coherent_dma_mask
of the USB in its PCI fixup to support this.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C. <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5596/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
commit 6ba045f (MIPS: Move generated code to .text for microMIPS)
causes a panic at boot. The handler builder should test against
handle_tlbs_end, not handle_tlbs.
Signed-off-by: Tony Wu <tung7970@gmail.com>
Acked-by: Jayachandran C. <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5600/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 4df715aa ["MIPS: BMIPS: support booting from physical CPU other
than 0"] introduced a thinko which will prevents slave CPUs from being
released from reset on systems where we boot from TP0. The problem is
that we are checking whether the slave CPU logical CPU map is 0, which
is never true for systems booting from TP0, so we do not release the
slave TP from reset and we are just stuck. Fix this by properly checking
that the CPU we intend to boot really is the physical slave CPU (logical
and physical value being 1).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: blogic@openwrt.org
Cc: jogo@openwrt.org
Cc: cernekee@gmail.com
Cc: Florian Fainelli <florian@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/5598/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
panic() doesn't return so this call was useless.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: Alexander Sverdlin <alexander.sverdlin@nsn.com>
commit 3747069b25e419f6b51395f48127e9812abc3596 upstream.
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
and are flagged as __cpuinit -- so if we remove the __cpuinit from
the arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
related content into no-ops as early as possible, since that will get
rid of these warnings. In any case, they are temporary and harmless.
Here, we remove all the MIPS __cpuinit from C code and __CPUINIT
from asm files. MIPS is interesting in this respect, because there
are also uasm users hiding behind their own renamed versions of the
__cpuinit macros.
[1] https://lkml.org/lkml/2013/5/20/589
[ralf@linux-mips.org: Folded in Paul's followup fix.]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5494/
Patchwork: https://patchwork.linux-mips.org/patch/5495/
Patchwork: https://patchwork.linux-mips.org/patch/5509/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull networking fixes from David Miller:
"Just a bunch of small fixes and tidy ups:
1) Finish the "busy_poll" renames, from Eliezer Tamir.
2) Fix RCU stalls in IFB driver, from Ding Tianhong.
3) Linearize buffers properly in tun/macvtap zerocopy code.
4) Don't crash on rmmod in vxlan, from Pravin B Shelar.
5) Spinlock used before init in alx driver, from Maarten Lankhorst.
6) A sparse warning fix in bnx2x broke TSO checksums, fix from Dmitry
Kravkov.
7) Dummy and ifb driver load failure paths can oops, fixes from Tan
Xiaojun and Ding Tianhong.
8) Correct MTU calculations in IP tunnels, from Alexander Duyck.
9) Account all TCP retransmits in SNMP stats properly, from Yuchung
Cheng.
10) atl1e and via-rhine do not handle DMA mapping failures properly,
from Neil Horman.
11) Various equal-cost multipath route fixes in ipv6 from Hannes
Frederic Sowa"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (36 commits)
ipv6: only static routes qualify for equal cost multipathing
via-rhine: fix dma mapping errors
atl1e: fix dma mapping warnings
tcp: account all retransmit failures
usb/net/r815x: fix cast to restricted __le32
usb/net/r8152: fix integer overflow in expression
net: access page->private by using page_private
net: strict_strtoul is obsolete, use kstrtoul instead
drivers/net/ieee802154: don't use devm_pinctrl_get_select_default() in probe
drivers/net/ethernet/cadence: don't use devm_pinctrl_get_select_default() in probe
drivers/net/can/c_can: don't use devm_pinctrl_get_select_default() in probe
net/usb: add relative mii functions for r815x
net/tipc: use %*phC to dump small buffers in hex form
qlcnic: Adding Maintainers.
gre: Fix MTU sizing check for gretap tunnels
pkt_sched: sch_qfq: remove forward declaration of qfq_update_agg_ts
pkt_sched: sch_qfq: improve efficiency of make_eligible
gso: Update tunnel segmentation to support Tx checksum offload
inet: fix spacing in assignment
ifb: fix oops when loading the ifb failed
...
Pull MIPS updates from Ralf Baechle:
"MIPS updates:
- All the things that didn't make 3.10.
- Removes the Windriver PPMC platform. Nobody will miss it.
- Remove a workaround from kernel/irq/irqdomain.c which was there
exclusivly for MIPS. Patch by Grant Likely.
- More small improvments for the SEAD 3 platform
- Improvments on the BMIPS / SMP support for the BCM63xx series.
- Various cleanups of dead leftovers.
- Platform support for the Cavium Octeon-based EdgeRouter Lite.
Two large KVM patchsets didn't make it for this pull request because
their respective authors are vacationing"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
MIPS: SEAD3: Disable L2 cache on SEAD-3.
MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
MIPS: BCM63xx: Add SMP support to prom.c
MIPS: define write{b,w,l,q}_relaxed
MIPS: Expose missing pci_io{map,unmap} declarations
MIPS: Malta: Update GCMP detection.
Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
MIPS: APSP: Remove <asm/kspd.h>
SSB: Kconfig: Amend SSB_EMBEDDED dependencies
MIPS: microMIPS: Fix improper definition of ISA exception bit.
MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
MIPS: Declare emulate_load_store_microMIPS as a static function.
MIPS: Fix typos and cleanup comment
MIPS: Cleanup indentation and whitespace
MIPS: BMIPS: support booting from physical CPU other than 0
MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
MIPS: GIC: Fix gic_set_affinity infinite loop
MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
...
Since all architectures have been converted to use vm_unmapped_area(),
there is no remaining use for the free_area_cache.
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename LL_SO to BUSY_POLL_SO
Rename sysctl_net_ll_{read,poll} to sysctl_busy_{read,poll}
Fix up users of these variables.
Fix documentation for sysctl.
a patch for the socket.7 man page will follow separately,
because of limitations of my mail setup.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"This is a re-do of the net-next pull request for the current merge
window. The only difference from the one I made the other day is that
this has Eliezer's interface renames and the timeout handling changes
made based upon your feedback, as well as a few bug fixes that have
trickeled in.
Highlights:
1) Low latency device polling, eliminating the cost of interrupt
handling and context switches. Allows direct polling of a network
device from socket operations, such as recvmsg() and poll().
Currently ixgbe, mlx4, and bnx2x support this feature.
Full high level description, performance numbers, and design in
commit 0a4db187a9 ("Merge branch 'll_poll'")
From Eliezer Tamir.
2) With the routing cache removed, ip_check_mc_rcu() gets exercised
more than ever before in the case where we have lots of multicast
addresses. Use a hash table instead of a simple linked list, from
Eric Dumazet.
3) Add driver for Atheros CQA98xx 802.11ac wireless devices, from
Bartosz Markowski, Janusz Dziedzic, Kalle Valo, Marek Kwaczynski,
Marek Puzyniak, Michal Kazior, and Sujith Manoharan.
4) Support reporting the TUN device persist flag to userspace, from
Pavel Emelyanov.
5) Allow controlling network device VF link state using netlink, from
Rony Efraim.
6) Support GRE tunneling in openvswitch, from Pravin B Shelar.
7) Adjust SOCK_MIN_RCVBUF and SOCK_MIN_SNDBUF for modern times, from
Daniel Borkmann and Eric Dumazet.
8) Allow controlling of TCP quickack behavior on a per-route basis,
from Cong Wang.
9) Several bug fixes and improvements to vxlan from Stephen
Hemminger, Pravin B Shelar, and Mike Rapoport. In particular,
support receiving on multiple UDP ports.
10) Major cleanups, particular in the area of debugging and cookie
lifetime handline, to the SCTP protocol code. From Daniel
Borkmann.
11) Allow packets to cross network namespaces when traversing tunnel
devices. From Nicolas Dichtel.
12) Allow monitoring netlink traffic via AF_PACKET sockets, in a
manner akin to how we monitor real network traffic via ptype_all.
From Daniel Borkmann.
13) Several bug fixes and improvements for the new alx device driver,
from Johannes Berg.
14) Fix scalability issues in the netem packet scheduler's time queue,
by using an rbtree. From Eric Dumazet.
15) Several bug fixes in TCP loss recovery handling, from Yuchung
Cheng.
16) Add support for GSO segmentation of MPLS packets, from Simon
Horman.
17) Make network notifiers have a real data type for the opaque
pointer that's passed into them. Use this to properly handle
network device flag changes in arp_netdev_event(). From Jiri
Pirko and Timo Teräs.
18) Convert several drivers over to module_pci_driver(), from Peter
Huewe.
19) tcp_fixup_rcvbuf() can loop 500 times over loopback, just use a
O(1) calculation instead. From Eric Dumazet.
20) Support setting of explicit tunnel peer addresses in ipv6, just
like ipv4. From Nicolas Dichtel.
21) Protect x86 BPF JIT against spraying attacks, from Eric Dumazet.
22) Prevent a single high rate flow from overruning an individual cpu
during RX packet processing via selective flow shedding. From
Willem de Bruijn.
23) Don't use spinlocks in TCP md5 signing fast paths, from Eric
Dumazet.
24) Don't just drop GSO packets which are above the TBF scheduler's
burst limit, chop them up so they are in-bounds instead. Also
from Eric Dumazet.
25) VLAN offloads are missed when configured on top of a bridge, fix
from Vlad Yasevich.
26) Support IPV6 in ping sockets. From Lorenzo Colitti.
27) Receive flow steering targets should be updated at poll() time
too, from David Majnemer.
28) Fix several corner case regressions in PMTU/redirect handling due
to the routing cache removal, from Timo Teräs.
29) We have to be mindful of ipv4 mapped ipv6 sockets in
upd_v6_push_pending_frames(). From Hannes Frederic Sowa.
30) Fix L2TP sequence number handling bugs, from James Chapman."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1214 commits)
drivers/net: caif: fix wrong rtnl_is_locked() usage
drivers/net: enic: release rtnl_lock on error-path
vhost-net: fix use-after-free in vhost_net_flush
net: mv643xx_eth: do not use port number as platform device id
net: sctp: confirm route during forward progress
virtio_net: fix race in RX VQ processing
virtio: support unlocked queue poll
net/cadence/macb: fix bug/typo in extracting gem_irq_read_clear bit
Documentation: Fix references to defunct linux-net@vger.kernel.org
net/fs: change busy poll time accounting
net: rename low latency sockets functions to busy poll
bridge: fix some kernel warning in multicast timer
sfc: Fix memory leak when discarding scattered packets
sit: fix tunnel update via netlink
dt:net:stmmac: Add dt specific phy reset callback support.
dt:net:stmmac: Add support to dwmac version 3.610 and 3.710
dt:net:stmmac: Allocate platform data only if its NULL.
net:stmmac: fix memleak in the open method
ipv6: rt6_check_neigh should successfully verify neigh if no NUD information are available
net: ipv6: fix wrong ping_v6_sendmsg return value
...
Pull slave-dmaengine updates from Vinod Koul:
"Once you have some time from extended weekend celebrations please
consider pulling the following to get:
- Various fixes and PCI driver for dw_dmac by Andy
- DT binding for imx-dma by Markus & imx-sdma by Shawn
- DT fixes for dmaengine by Lars
- jz4740 dmac driver by Lars
- and various fixes across the drivers"
What "extended weekend celebrations"? I'm in the merge window, who has
time for extended celebrations..
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (40 commits)
DMA: shdma: add DT support
DMA: shdma: shdma_chan_filter() has to be in shdma-base.h
DMA: shdma: (cosmetic) don't re-calculate a pointer
dmaengine: at_hdmac: prepare clk before calling enable
dmaengine/trivial: at_hdmac: add curly brackets to if/else expressions
dmaengine: at_hdmac: remove unsuded atc_cleanup_descriptors()
dmaengine: at_hdmac: add FIFO configuration parameter to DMA DT binding
ARM: at91: dt: add header to define at_hdmac configuration
MIPS: jz4740: Correct clock gate bit for DMA controller
MIPS: jz4740: Remove custom DMA API
MIPS: jz4740: Register jz4740 DMA device
dma: Add a jz4740 dmaengine driver
MIPS: jz4740: Acquire and enable DMA controller clock
dma: mmp_tdma: disable irq when disabling dma channel
dmaengine: PL08x: Avoid collisions with get_signal() macro
dmaengine: dw: select DW_DMAC_BIG_ENDIAN_IO automagically
dma: dw: add PCI part of the driver
dma: dw: split driver to library part and platform code
dma: move dw_dmac driver to an own directory
dw_dmac: don't check resource with devm_ioremap_resource
...
Now that all users of the custom jz4740 DMA API have been converted to use
the dmaengine API instead we can remove the custom API and move all the code
talking to the hardware to the dmaengine driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Previously, it was assumed that the DMA controller clock is not gated
when the kernel starts running. While that is the power-on state, it is
safer to not rely on that.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Merge Kconfig menu diet patches from Dave Hansen:
"I think the "Kernel Hacking" menu has gotten a bit out of hand. It is
over 120 lines long on my system with everything enabled and options
are scattered around it haphazardly.
http://sr71.net/~dave/linux/kconfig-horror.png
Let's try to introduce some sanity. This set takes that 120 lines
down to 55 and makes it vastly easier to find some things. It's a
start.
This set stands on its own, but there is plenty of room for follow-up
patches. The arch-specific debug options still end up getting stuck
in the top-level "kernel hacking" menu. OPTIMIZE_INLINING, for
instance, could obviously go in to the "compiler options" menu, but
the fact that it is defined in arch/ in a separate Kconfig file keeps
it on its own for the moment.
The Signed-off-by's in here look funky. I changed employers while
working on this set, so I have signoffs from both email addresses"
* emailed patches from Dave Hansen <dave@sr71.net>:
hang and lockup detection menu
kconfig: consolidate printk options
group locking debugging options
consolidate compilation option configs
consolidate runtime testing configs
order memory debugging Kconfig options
consolidate per-arch stack overflow debugging options
Original posting:
http://lkml.kernel.org/r/20121214184202.F54094D9@kernel.stglabs.ibm.com
Several architectures have similar stack debugging config options.
They all pretty much do the same thing, some with slightly
differing help text.
This patch changes the architectures to instead enable a Kconfig
boolean, and then use that boolean in the generic Kconfig.debug
to present the actual menu option. This removes a bunch of
duplication and adds consistency across arches.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com> [for tile]
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge first patch-bomb from Andrew Morton:
- various misc bits
- I'm been patchmonkeying ocfs2 for a while, as Joel and Mark have been
distracted. There has been quite a bit of activity.
- About half the MM queue
- Some backlight bits
- Various lib/ updates
- checkpatch updates
- zillions more little rtc patches
- ptrace
- signals
- exec
- procfs
- rapidio
- nbd
- aoe
- pps
- memstick
- tools/testing/selftests updates
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (445 commits)
tools/testing/selftests: don't assume the x bit is set on scripts
selftests: add .gitignore for kcmp
selftests: fix clean target in kcmp Makefile
selftests: add .gitignore for vm
selftests: add hugetlbfstest
self-test: fix make clean
selftests: exit 1 on failure
kernel/resource.c: remove the unneeded assignment in function __find_resource
aio: fix wrong comment in aio_complete()
drivers/w1/slaves/w1_ds2408.c: add magic sequence to disable P0 test mode
drivers/memstick/host/r592.c: convert to module_pci_driver
drivers/memstick/host/jmb38x_ms: convert to module_pci_driver
pps-gpio: add device-tree binding and support
drivers/pps/clients/pps-gpio.c: convert to module_platform_driver
drivers/pps/clients/pps-gpio.c: convert to devm_* helpers
drivers/parport/share.c: use kzalloc
Documentation/accounting/getdelays.c: avoid strncpy in accounting tool
aoe: update internal version number to v83
aoe: update copyright date
aoe: perform I/O completions in parallel
...
saved_max_pfn is used to know the amount of memory that the previous
kernel used. And for powerpc, we set saved_max_pfn by passing the kernel
commandline parameter "savemaxmem=".
The only user of saved_max_pfn in mips is read_oldmem interface. Since we
have removed read_oldmem, so we don't need this parameter anymore.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prepare for killing free_all_bootmem_node() by using free_all_bootmem().
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Concentrate code to modify totalram_pages into the mm core, so the arch
memory initialized code doesn't need to take care of it. With these
changes applied, only following functions from mm core modify global
variable totalram_pages: free_bootmem_late(), free_all_bootmem(),
free_all_bootmem_node(), adjust_managed_page_count().
With this patch applied, it will be much more easier for us to keep
totalram_pages and zone->managed_pages in consistence.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: <sworddragon2@aol.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Michel Lespinasse <walken@google.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
