The H3 has an ARM Mali 400 GPU, so add binding to our DT.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The rk3328 quad-core Cortex A53 uses a Mali-450MP2 with 2 PPs, so
add a compatible for it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Rob Herring <robh@kernel.org>
On some socs Mali Utgard gpus have both soc power-domains and external
supplying regulators, so add an optional power-domains property for
reference.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Mali GPUs have a separate supplying regulator in a lot of socs,
so describe a mali-supply property. The already described
operating points will likely also need access to this regulator.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Some (older or lower power) Rockchip socs use Utgard-based Mali-GPUs.
So add the necessary compatibles for them. As the setup is the same for
all of them (needing only the additional reset line), they get added in
a somewhat condensed form, to not inflate the document unnecessary.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
As usual, device tree updates is the bulk of our material in this merge
window. This time around, 559 patches affecting both 32- and 64-bit
platforms.
Changes are too many to list individually, but some of the larger ones:
New platform/SoC support:
- Automotive:
+ Renesas R-Car D3 (R8A77995)
+ TI DT76x
+ MediaTek mt2712e
- Communication-oriented:
+ Qualcomm IPQ8074
+ Broadcom Stingray
+ Marvell Armada 8080
- Set top box:
+ Uniphier PXs3
Besides some vendor reference boards for the SoC above, there are also several
new boards/machines:
- TI AM335x Moxa UC-8100-ME-T open platform
- TI AM57xx Beaglebone X15 Rev C
- Microchip/Atmel sama5d27 SoM1 EK
- Broadcom Raspberry Pi Zero W
- Gemini-based D-Link DIR-685 router
- Freescale i.MX6:
+ Toradex Apalis module + Apalis and Ixora carrier boards
+ Engicam GEAM6UL Starter Kit
- Freescale i.MX53-based Beckhoff CX9020 Embedded PC
- Mediatek mt7623-based BananaPi R2
- Several Allwinner-based single-board computers:
+ Cubietruck plus
+ Bananapi M3, M2M and M64
+ NanoPi A64
+ A64-OLinuXino
+ Pine64
- Rockchip RK3328 Pine64/Rock64 board support
- Rockchip RK3399 boards:
+ RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
+ Theobroma Systems RK3399-Q7 SoM
- ZTE ZX296718 PCBOX Board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R45j
-----END PGP SIGNATURE-----
Merge tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM/arm64 Devicetree updates from Olof Johansson:
"As usual, device tree updates is the bulk of our material in this
merge window. This time around, 559 patches affecting both 32- and
64-bit platforms.
Changes are too many to list individually, but some of the larger
ones:
New platform/SoC support:
- Automotive:
+ Renesas R-Car D3 (R8A77995)
+ TI DT76x
+ MediaTek mt2712e
- Communication-oriented:
+ Qualcomm IPQ8074
+ Broadcom Stingray
+ Marvell Armada 8080
- Set top box:
+ Uniphier PXs3
Besides some vendor reference boards for the SoC above, there are also
several new boards/machines:
- TI AM335x Moxa UC-8100-ME-T open platform
- TI AM57xx Beaglebone X15 Rev C
- Microchip/Atmel sama5d27 SoM1 EK
- Broadcom Raspberry Pi Zero W
- Gemini-based D-Link DIR-685 router
- Freescale i.MX6:
+ Toradex Apalis module + Apalis and Ixora carrier boards
+ Engicam GEAM6UL Starter Kit
- Freescale i.MX53-based Beckhoff CX9020 Embedded PC
- Mediatek mt7623-based BananaPi R2
- Several Allwinner-based single-board computers:
+ Cubietruck plus
+ Bananapi M3, M2M and M64
+ NanoPi A64
+ A64-OLinuXino
+ Pine64
- Rockchip RK3328 Pine64/Rock64 board support
- Rockchip RK3399 boards:
+ RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
+ Theobroma Systems RK3399-Q7 SoM
- ZTE ZX296718 PCBOX Board"
* tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (559 commits)
ARM: dts: at91: at91sam9g45: add AC97
arm64: dts: marvell: mcbin: enable more networking ports
arm64: dts: marvell: add a reference to the sysctrl syscon in the ppv2 node
arm64: dts: marvell: add TX interrupts for PPv2.2
arm64: dts: uniphier: add PXs3 SoC support
ARM: dts: uniphier: add pinctrl groups of ethernet phy mode
ARM: dts: uniphier: fix size of sdctrl nodes
ARM: dts: uniphier: add AIDET nodes
arm64: dts: uniphier: fix size of sdctrl node
arm64: dts: uniphier: add AIDET nodes
Revert "ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2"
arm64: dts: uniphier: add reset controller node of analog amplifier
arm64: dts: marvell: add Device Tree files for Armada-8KP
arm64: dts: rockchip: add Haikou baseboard with RK3399-Q7 SoM
arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM
dt-bindings: add rk3399-q7 SoM
ARM: dts: rockchip: enable usb for rv1108-evb
ARM: dts: rockchip: add usb nodes for rv1108 SoCs
dt-bindings: update grf-binding for rv1108 SoCs
ARM: dts: aspeed-g4: fix AHB window size of the SMC controllers
...
- Convert more DT code to use of_property_read_* API.
- Improve DT overlay support when adding multiple overlays.
- Convert printk's to %pOF format specifiers. Most went via subsystem
trees, but picked up the remaining orphans.
- Correct unittests to use preferred "okay" for "status" property value.
- Add a KASLR seed property.
- Vendor prefixes for Mellanox, Theobroma System, Adaptrum, Moxa.
- Fix modalias buffer handling.
- Clean-up of include paths for building dtbs.
- Add bindings for amc6821, isl1208, tsl2x7x, srf02, and srf10 devices.
- Add nvmem bindings for MediaTek MT7623 and MT7622 SoC.
- Add compatible string for Allwinner H5 Mali-450 GPU.
- Fix links to old OpenFirmware docs with new mirror on devicetree.org.
- Remove status property from binding doc examples.
-----BEGIN PGP SIGNATURE-----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=IBAh
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"There's a few orphans in the conversion to %pOF printf specifiers
included here that no one else picked up.
Summary:
- Convert more DT code to use of_property_read_* API.
- Improve DT overlay support when adding multiple overlays
- Convert printk's to %pOF format specifiers. Most went via subsystem
trees, but picked up the remaining orphans
- Correct unittests to use preferred "okay" for "status" property
value
- Add a KASLR seed property
- Vendor prefixes for Mellanox, Theobroma System, Adaptrum, Moxa
- Fix modalias buffer handling
- Clean-up of include paths for building dtbs
- Add bindings for amc6821, isl1208, tsl2x7x, srf02, and srf10
devices
- Add nvmem bindings for MediaTek MT7623 and MT7622 SoC
- Add compatible string for Allwinner H5 Mali-450 GPU
- Fix links to old OpenFirmware docs with new mirror on
devicetree.org
- Remove status property from binding doc examples"
* tag 'devicetree-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (45 commits)
devicetree: Adjust status "ok" -> "okay" under drivers/of/
dt-bindings: Remove "status" from examples
dt-bindings: pinctrl: sh-pfc: Use generic node name
dt-bindings: Add vendor Mellanox
dt-binding: net/phy: fix interrupts description
virt: Convert to using %pOF instead of full_name
macintosh: Convert to using %pOF instead of full_name
ide: pmac: Convert to using %pOF instead of full_name
microblaze: Convert to using %pOF instead of full_name
dt-bindings: usb: musb: Grammar s/the/to/, s/is/are/
of: Use PLATFORM_DEVID_NONE definition
of/device: Fix of_device_get_modalias() buffer handling
of/device: Prevent buffer overflow in of_device_modalias()
dt-bindings: add amc6821, isl1208 trivial bindings
dt-bindings: add vendor prefix for Theobroma Systems
of: search scripts/dtc/include-prefixes path for both CPP and DTC
of: remove arch/$(SRCARCH)/boot/dts from include search path for CPP
of: remove drivers/of/testcase-data from include search path for CPP
of: return of_get_cpu_node from of_cpu_device_node_get if CPUs are not registered
iio: srf08: add device tree binding for srf02 and srf10
...
Pretty much any node can have a status property, so it doesn't need to
be in examples.
Converted with the following command and removed examples with SoC and
board specific splits:
git grep -l -E 'status.*=.*' Documentation/devicetree/ | xargs sed -i -E '/\sstatus.*=.*"(disabled|ok|okay)/d'
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
and the use of keep-power-in-suspend in non-sdio nodes as well as the
removal of the deprecated num-slots property from dwmmc nodes.
rk3328 gets support for spdif, io-domains and usb (including enablement
of usb on the evaluation board), while rk3368 gains support for spdif.
The biggest chunk of course aims for the rk3399 with a number of pcie
changes, support for the mali gpu, a new power-domain, sdmmc support
on the firefly board and dynamic-power-coefficients.
The gru family also gets support for their quite central pwm regulators
using the newly introduced vctrl regulator types.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlmET9EQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgZbjCACKFO9Hp8Xwwg2nEM8DL3i+MlGaqxjIrcsb
WskuVOJjkAA4hMnrd7XvbpzJJusAquGqMd042ZCWtrNa1AwzCy0ZkYjDFNL27rXH
DqrHmJZowSoTHxlo8QKaevXH3ZZnp8TDz4IqaD0+UZx7DgZSOjR1a+feseh1Jn/V
9WBUJhNAFtKMiJBkTIpaDUk0E6OxIspdvlJurYmwUvDbfZKlpZrXHYKXSuUhFS9s
JX4Dqi5eF96Mctpi8GhaHGf7awPQf4oQBZfsXxhhS/efzX/v0HWqUPt40o2THi0F
ZbFFE3xAFaWisA+cbg8xnzJc8ZAwz2UmS6FgQ9lrqKyGN74buwgP
=spNi
-----END PGP SIGNATURE-----
Merge tag 'v4.14-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt64
Pull "Rockchip dts64 changes for 4.14" from Heiko Stübner:
64bit Rockchip devicetree changes containing fixes for pinctrl typos
and the use of keep-power-in-suspend in non-sdio nodes as well as the
removal of the deprecated num-slots property from dwmmc nodes.
rk3328 gets support for spdif, io-domains and usb (including enablement
of usb on the evaluation board), while rk3368 gains support for spdif.
The biggest chunk of course aims for the rk3399 with a number of pcie
changes, support for the mali gpu, a new power-domain, sdmmc support
on the firefly board and dynamic-power-coefficients.
The gru family also gets support for their quite central pwm regulators
using the newly introduced vctrl regulator types.
* tag 'v4.14-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: update dynamic-power-coefficient for rk3399
arm64: dts: rockchip: add rk3328 spdif node
arm64: dts: rockchip: add rk3368 spdif node
arm64: dts: rockchip: enable sdmmc controller on rk3399-firefly
arm64: dts: rockchip: Add rk3328 io-domain node
arm64: dts: rockchip: kill pcie_clkreqn and pcie_clkreqnb for rk3399
arm64: dts: rockchip: change clkreq mode for rk3399-firefly
arm64: dts: rockchip: enable the GPU for RK3399-GRU
arm64: dts: rockchip: add ARM Mali GPU node for RK3399 SoCs
dt-bindings: gpu: add the RK3399 mali for rockchip specifics
arm64: dts: rockchip: remove abused keep-power-in-suspend
arm64: dts: rockchip: remove num-slots from all platforms
arm64: dts: rockchip: change clkreq mode for rk3399-evb
arm64: dts: rockchip: add SdioAudio pd control for rk3399
arm64: dts: rockchip: enable usb2 for RK3328 evaluation board
arm64: dts: rockchip: add usb2 nodes for RK3328 SoCs
arm64: dts: rockchip: set rk3399 dynamic CPU power coefficients
arm64: dts: rockchip: Use vctrl regulators for dynamic CPU voltages on Gru/Kevin
arm64: dts: rockchip: Update CPU regulator voltage ranges for Gru
arm64: dts: rockchip: fix typo in mmc pinctrl
Allwinner H5 has a Mali-450 MP4 GPU, which has a reset line like other
Allwinner SoCs with Mali Utgard, but it's a Mali-450, so it needs a new
compatible.
Add the new compatible to Mali Utgard binding document.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Rob Herring <robh@kernel.org>
RK3399's GPU uses the quad-core Mali-T860, which is the new generation of
high-end graphics processors from ARM.
This patch added "rockchip,rk3399-mali" for dt-bindings, in order to
support IPA of gpu thermal in later.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The binding rightfully only specifies compatibles for actual implementations
and not for the whole family. In the example an arm,mali-midgard slipped
through from downstream devicetrees though. So drop that to not confuse
people reading (or copying) that example.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
The ARM Mali Midgard GPU family is present in a number of SoCs
from many different vendors such as Samsung Exynos and Rockchip.
Import the device tree bindings documentation from the r16p0
release of the Mali Midgard GPU kernel driver:
https://developer.arm.com/-/media/Files/downloads/mali-drivers/kernel/mali-midgard-gpu/TX011-SW-99002-r16p0-00rel0.tgz
Remove the copyright and GPL licence header as deemed not necessary.
Redesign the "compatible" property strings to list all the Mali
Midgard GPU types and add vendor specific ones.
Drop the "clock-names" property as the Mali Midgard GPU uses only one
clock (the driver now needs to call clk_get with NULL).
Convert the "interrupt-names" property values to lower-case: "job",
"mmu" and "gpu".
Replace the deprecated "operating-points" optional property with
"operating-points-v2".
Omit the following optional properties in this initial version as they
are only used in very specific cases:
* snoop_enable_smc
* snoop_disable_smc
* jm_config
* power_model
* system-coherency
* ipa-model
Update the example accordingly to reflect all these changes, based on
rk3288 mali-t760.
CC: John Reitan <john.reitan@arm.com>
Signed-off-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This contains an update for the flow controller device tree binding as
well as the addition of the binding for the GP10B GPU found on the new
Tegra186 (Parker) SoC.
-----BEGIN PGP SIGNATURE-----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=EArG
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.12-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
dt-bindings: Updates for v4.12-rc1
This contains an update for the flow controller device tree binding as
well as the addition of the binding for the GP10B GPU found on the new
Tegra186 (Parker) SoC.
* tag 'tegra-for-4.12-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: Add documentation for GP10B GPU
dt-bindings: tegra: Update compatible strings for Tegra flowctrl
Signed-off-by: Olof Johansson <olof@lixom.net>
GP10B's definition is mostly similar to GK20A's and GM20B's. The only
noticeable difference is the use of power domains instead of a regulator
for power supply.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The operating-points-v2 binding gives a way to provide the OPP of the GPU.
Let's use it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
The reserved memory bindings allow us to specify which memory areas our
buffers can be allocated from.
Let's use it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
The ARM Mali Utgard GPU family is embedded into a number of SoCs from
Allwinner, Amlogic, Mediatek or Rockchip.
Add a binding for the GPU of that family.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
GM20B's definition is mostly similar to GK20A's, but requires an
additional clock.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
GK20A can optionally make use of an IOMMU.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The correct compatible name is "nvidia,gk20a".
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This is a quite large renaming to consolidate display related bindings
into a single "display" directory from various scattered locations of
video, drm, gpu, fb, mipi, and panel. The prior location was somewhat
based on the Linux driver location, but bindings should be independent
of that.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
There are a bunch of non-critical fixes here that I've collected over
the past few months, but the biggest part is Tegra210 support, in the
DC, DSI and SOR/HDMI drivers.
Also this finally restores DPMS with atomic mode-setting, something
that has been broken since the conversion and which I had originally
expected to take far less longer to fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=lxYn
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-4.3-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.3-rc1
There are a bunch of non-critical fixes here that I've collected over
the past few months, but the biggest part is Tegra210 support, in the
DC, DSI and SOR/HDMI drivers.
Also this finally restores DPMS with atomic mode-setting, something
that has been broken since the conversion and which I had originally
expected to take far less longer to fix.
* tag 'drm/tegra/for-4.3-rc1' of git://anongit.freedesktop.org/tegra/linux: (41 commits)
drm/tegra: sor: Add HDMI support
drm/tegra: sor: Add Tegra210 eDP support
drm/tegra: dc: Implement atomic DPMS
drm/tegra: sor: Restore DPMS
drm/tegra: dsi: Restore DPMS
drm/tegra: hdmi: Restore DPMS
drm/tegra: rgb: Restore DPMS
drm/tegra: sor: Use DRM debugfs infrastructure for CRC
drm/tegra: sor: Write correct head state registers
drm/tegra: sor: Constify display mode
drm/tegra: sor: Reset the correct debugfs fields
drm/tegra: sor: Set minor after debugfs initialization
drm/tegra: sor: Provide error messages in probe
drm/tegra: sor: Rename registers for consistency
drm/tegra: dpaux: Disable interrupt when detached
drm/tegra: dpaux: Configure pads as I2C by default
drm/tegra: dpaux: Provide error message in probe
drm/tegra: dsi: Add Tegra210 support
drm/tegra: dsi: Add Tegra132 support
drm/tegra: dsi: Add Tegra124 support
...
The SOR1 introduced on Tegra210 supports HDMI 2.0 and DisplayPort. Add
HDMI support and name the debugfs node after the type of SOR. The SOR
introduced with Tegra124 is known simply as "sor", whereas the
additional SOR found on Tegra210 is known as "sor1".
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SOR found on Tegra210 is very similar to the version found on
Tegra124, except that it no longer supports LVDS.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Fix misunderstanding in how use component framework.
drm_platform_init() is now call only when all the
sub-components are register themselves instead of the
previous broken two stages mechanism.
Update bindings documentation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Pull drm updates from Dave Airlie:
"This is the main drm pull, it has a shared branch with some alsa
crossover but everything should be acked by relevant people.
New drivers:
- ATMEL HLCDC driver
- designware HDMI core support (used in multiple SoCs).
core:
- lots more atomic modesetting work, properties and atomic ioctl
(hidden under option)
- bridge rework allows support for Samsung exynos chromebooks to
work finally.
- some more panels supported
i915:
- atomic plane update support
- DSI uses shared DSI infrastructure
- Skylake basic support is all merged now
- component framework used for i915/snd-hda interactions
- write-combine cpu memory mappings
- engine init code refactored
- full ppgtt enabled where execlists are enabled.
- cherryview rps/gpu turbo and pipe CRC support.
radeon:
- indirect draw support for evergreen/cayman
- SMC and manual fan control for SI/CI
- Displayport audio support
amdkfd:
- SDMA usermode queue support
- replace suballocator usage with more suitable one
- rework for allowing interfacing to more than radeon
nouveau:
- major renaming in prep for later splitting work
- merge arm platform driver into nouveau
- GK20A reclocking support
msm:
- conversion to atomic modesetting
- YUV support for mdp4/5
- eDP support
- hw cursor for mdp5
tegra:
- conversion to atomic modesetting
- better suspend/resume support for child devices
rcar-du:
- interlaced support
imx:
- move to using dw_hdmi shared support
- mode_fixup support
sti:
- DVO support
- HDMI infoframe support
exynos:
- refactoring and cleanup, removed lots of internal unnecessary
abstraction
- exynos7 DECON display controller support
Along with the usual bunch of fixes, cleanups etc"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (724 commits)
drm/radeon: fix voltage setup on hawaii
drm/radeon/dp: Set EDP_CONFIGURATION_SET for bridge chips if necessary
drm/radeon: only enable kv/kb dpm interrupts once v3
drm/radeon: workaround for CP HW bug on CIK
drm/radeon: Don't try to enable write-combining without PAT
drm/radeon: use 0-255 rather than 0-100 for pwm fan range
drm/i915: Clamp efficient frequency to valid range
drm/i915: Really ignore long HPD pulses on eDP
drm/exynos: Add DECON driver
drm/i915: Correct the base value while updating LP_OUTPUT_HOLD in MIPI_PORT_CTRL
drm/i915: Insert a command barrier on BLT/BSD cache flushes
drm/i915: Drop vblank wait from intel_dp_link_down
drm/exynos: fix NULL pointer reference
drm/exynos: remove exynos_plane_dpms
drm/exynos: remove mode property of exynos crtc
drm/exynos: Remove exynos_plane_dpms() call with no effect
drm/i915: Squelch overzealous uncore reset WARN_ON
drm/i915: Take runtime pm reference on hangcheck_info
drm/i915: Correct the IOSF Dev_FN field for IOSF transfers
drm/exynos: fix DMA_ATTR_NO_KERNEL_MAPPING usage
...
Align compatible strings for several IP blocks present on Tegra chips
with the latest doctrine from the DT maintainers:
http://marc.info/?l=devicetree&m=142255654213019&w=2
The primary objective here is to avoid checkpatch warnings, per:
http://marc.info/?l=linux-tegra&m=142201349727836&w=2
DT binding text files have been updated for the following IP blocks:
- PCIe
- SOR
- SoC timers
- AHB "gizmo"
- APB_MISC
- pinmux control
- UART
- PWM
- I2C
- SPI
- RTC
- PMC
- eFuse
- AHCI
- HDA
- XUSB_PADCTRL
- SDHCI
- SOC_THERM
- AHUB
- I2S
- EHCI
- USB PHY
N.B. The nvidia,tegra20-timer compatible string is removed from the
nvidia,tegra30-timer.txt documentation file because it's already
mentioned in the nvidia,tegra20-timer.txt documentation file.
This second version takes into account the following requests from
Rob Herring <robherring2@gmail.com>:
- Per-IP block patches have been combined into a single patch
- Explicit documentation about which compatible strings are actually
matched by the driver has been removed. In its place is implicit
documentation that loosely follows Rob's prescribed format:
"Must contain '"nvidia,<chip>-pcie", "nvidia,tegra20-pcie"' where
<chip> is tegra30, tegra132, ..." [...] "You should attempt to
document known values of <chip> if you use it"
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Dylan Reid <dgreid@chromium.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Jingchang Lu <jingchang.lu@freescale.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mikko Perttunen <mperttunen@nvidia.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Tejun Heo <tj@kernel.org>
Cc: "Terje Bergström" <tbergstrom@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-i2c@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-pwm@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Digital Video Out connector driver LCD panels.
Like HDMI and HDA it create bridge, encoder and connector
drm object.
Add binding description.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
High Quality Video Data Plane is hardware IP dedicated
to video rendering. Compare to GPD (graphic planes) it
have better scaler capabilities.
HQVDP use VID layer to push data into hardware compositor
without going into DDR. From data flow point of view HQVDP
and VID are nested so HQVPD update/disable VID.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
gpio used for HDMI hot plug detection is useless,
HDMI_STI register contains an hot plug detection status bit.
Fix binding documentation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Depending of the board configuration i2c for ddc could change,
this patch allow to use a phandle to specify which i2c controller to use.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Implement ganged mode support for the Tegra DSI driver. The DSI host
controller to gang up with is specified via a phandle in the device tree
and the resolved DSI host controller used for the programming of the
ganged-mode registers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Unlike the board branch, this keeps having large sets of changes for
every release, but that's quite expected and is so far working well.
Most of this is plumbing for various device bindings and new platforms,
but there's also a bit of cleanup and code removal for things that
are moved from platform code to DT contents (some OMAP clock code in
particular).
There's also a pinctrl driver for tegra here (appropriately acked),
that's introduced this way to make it more bisectable.
I'm happy to say that there were no conflicts at all with this branch
this release, which means that changes are flowing through our tree as
expected instead of merged through driver maintainers (or at least not
done with conflicts).
There are several new boards added, and a couple of SoCs. In no particular
order:
* Rockchip RK3288 SoC support, including DTS for a dev board that they
have seeded with some community developers.
* Better support for Hardkernel Exynos4-based ODROID boards.
* CCF conversions (and dtsi contents) for several Renesas platforms.
* Gumstix Pepper (TI AM335x) board support
* TI eval board support for AM437x
* Allwinner A23 SoC, very similar to existing ones which mostly has
resulted in DT changes for support. Also includes support for an Ippo
tablet with the chipset.
* Allwinner A31 Hummingbird board support, not to be confused with the
SolidRun i.MX-based Hummingboard.
* Tegra30 Apalis board support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=xxlY
-----END PGP SIGNATURE-----
Merge tag 'dt-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device-tree changes from Olof Johansson:
"Unlike the board branch, this keeps having large sets of changes for
every release, but that's quite expected and is so far working well.
Most of this is plumbing for various device bindings and new
platforms, but there's also a bit of cleanup and code removal for
things that are moved from platform code to DT contents (some OMAP
clock code in particular).
There's also a pinctrl driver for tegra here (appropriately acked),
that's introduced this way to make it more bisectable.
I'm happy to say that there were no conflicts at all with this branch
this release, which means that changes are flowing through our tree as
expected instead of merged through driver maintainers (or at least not
done with conflicts).
There are several new boards added, and a couple of SoCs. In no
particular order:
- Rockchip RK3288 SoC support, including DTS for a dev board that
they have seeded with some community developers.
- Better support for Hardkernel Exynos4-based ODROID boards.
- CCF conversions (and dtsi contents) for several Renesas platforms.
- Gumstix Pepper (TI AM335x) board support
- TI eval board support for AM437x
- Allwinner A23 SoC, very similar to existing ones which mostly has
resulted in DT changes for support. Also includes support for an
Ippo tablet with the chipset.
- Allwinner A31 Hummingbird board support, not to be confused with
the SolidRun i.MX-based Hummingboard.
- Tegra30 Apalis board support"
* tag 'dt-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (334 commits)
ARM: dts: Enable USB host0 (EHCI) on rk3288-evb
ARM: dts: add rk3288 ehci usb devices
ARM: dts: Turn on USB host vbus on rk3288-evb
ARM: tegra: apalis t30: fix device tree compatible node
ARM: tegra: paz00: Fix some indentation inconsistencies
ARM: zynq: DT: Clarify Xilinx Zynq platform
ARM: dts: rockchip: add watchdog node
ARM: dts: rockchip: remove pinctrl setting from radxarock uart2
ARM: dts: Add missing pinctrl for uart0/1 for exynos3250
ARM: dts: Remove duplicate 'interrput-parent' property for exynos3250
ARM: dts: Add TMU dt node to monitor the temperature for exynos3250
ARM: dts: Specify MAX77686 pmic interrupt for exynos5250-smdk5250
ARM: dts: cypress,cyapa trackpad is exynos5250-Snow only
ARM: dts: max77686 is exynos5250-snow only
ARM: zynq: DT: Remove DMA from board DTs
ARM: zynq: DT: Add CAN node
ARM: EXYNOS: Add exynos5260 PMU compatible string to DT match table
ARM: dts: Add PMU DT node for exynos5260 SoC
ARM: EXYNOS: Add support for Exynos5410 PMU
ARM: dts: Add PMU to exynos5410
...
Add DRM/KMS driver bindings documentation.
Describe the required properties for each of the hardware IPs drivers.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Add the device tree binding documentation for the GK20A GPU used in
Tegra K1 SoCs.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The DSI controllers are powered by a (typically 1.2V) regulator. Usually
this is always on, so there was no need to support enabling or disabling
it thus far. But in order not to consume any power when DSI is inactive,
give the driver a chance to enable or disable the supply as needed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Revert commit 18ebc0f404 "drm/tegra: hdmi: Enable VDD earlier for
hotplug/DDC" and instead add a new supply for the +5V pin on the HDMI
connector.
The vdd-supply property refers to the regulator that supplies the
AVDD_HDMI input on Tegra, rather than the +5V HDMI connector pin. This
was never a problem before, because all boards had that pin hooked up to
a regulator that was always on. Starting with Dalmore and continuing
with Venice2, the +5V pin is controllable via a GPIO. For reasons
unknown, the GPIO ended up as the controlling GPIO of the AVDD_HDMI
supply in the Dalmore and Venice2 DTS files. But that's not correct.
Instead, a separate supply must be introduced so that the +5V pin can be
controlled separately from the supplies that feed the HDMI block within
Tegra.
A new hdmi-supply property is introduced that takes the place of the
vdd-supply and vdd-supply is only enabled when HDMI is enabled rather
than all the time.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for eDP functionality found on Tegra124 and later SoCs. Only
fast link training is currently supported.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The head number of a given display controller is fixed in hardware and
required to program outputs appropriately. Relying on the driver probe
order to determine this number will not work, since that could yield a
situation where the second head was probed first and would be assigned
head number 0 instead of 1.
By explicitly specifying the head number in the device tree, it is no
longer necessary to rely on these assumptions. As a fallback, if the
property isn't available, derive the head number from the display
controller node's position in the device tree. That's somewhat more
reliable than the previous default but not a proper solution.
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit adds support for both DSI outputs found on Tegra. Only very
minimal functionality is implemented, so advanced features like ganged
mode won't work.
Due to the lack of other test hardware, some sections of the driver are
hardcoded to work with Dalmore.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The display controller primary clock was recently renamed to "dc", so
update the example to reflect that.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use the DRM panel framework to attach a panel to an output. If the panel
attached to a connector supports supports the backlight brightness
accessors, a property will be available to allow the brightness to be
modified from userspace.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Update all the Tegra DT bindings to require resets/reset-names properties
where the HW module has reset inputs. Remove any entries from clocks or
clock-names that were only required to identify reset inputs, rather than
referring to real clocks.
This is a DT-ABI-incompatible change. It is the first of two changes
required for me to consider the Tegra DT bindings as stable, the other
being conversion to the common DMA DT bindings.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-By: Terje Bergstrom <tbergstrom@nvidia.com>
Many of the Tegra DT binding documents say nothing about the clocks or
clock-names properties, yet those are present and required in DT files.
This patch simply updates the documentation file to match the implicit
definition of the binding, based on real-world DT content.
All Tegra bindings that mention clocks are updated to have consistent
wording and formatting of the clock-related properties.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-By: Terje Bergstrom <tbergstrom@nvidia.com>
patches, both new drivers and fixes to existing. A high percentage of
these are for Samsung platforms like Exynos. Core framework fixes and
some new features like automagical clock re-parenting round out the
patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=5GfA
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.12' of git://git.linaro.org/people/mturquette/linux
Pull clock framework changes from Michael Turquette:
"The common clk framework changes for 3.12 are dominated by clock
driver patches, both new drivers and fixes to existing. A high
percentage of these are for Samsung platforms like Exynos. Core
framework fixes and some new features like automagical clock
re-parenting round out the patches"
* tag 'clk-for-linus-3.12' of git://git.linaro.org/people/mturquette/linux: (102 commits)
clk: only call get_parent if there is one
clk: samsung: exynos5250: Simplify registration of PLL rate tables
clk: samsung: exynos4: Register PLL rate tables for Exynos4x12
clk: samsung: exynos4: Register PLL rate tables for Exynos4210
clk: samsung: exynos4: Reorder registration of mout_vpllsrc
clk: samsung: pll: Add support for rate configuration of PLL46xx
clk: samsung: pll: Use new registration method for PLL46xx
clk: samsung: pll: Add support for rate configuration of PLL45xx
clk: samsung: pll: Use new registration method for PLL45xx
clk: samsung: exynos4: Rename exynos4_plls to exynos4x12_plls
clk: samsung: exynos4: Remove checks for DT node
clk: samsung: exynos4: Remove unused static clkdev aliases
clk: samsung: Modify _get_rate() helper to use __clk_lookup()
clk: samsung: exynos4: Use separate aliases for cpufreq related clocks
clocksource: samsung_pwm_timer: Get clock from device tree
ARM: dts: exynos4: Specify PWM clocks in PWM node
pwm: samsung: Update DT bindings documentation to cover clocks
clk: Move symbol export to proper location
clk: fix new_parent dereference before null check
clk: wm831x: Initialise wm831x pointer on init
...
The exynos4 platform is only dt-based since 3.10, we should convert driver data
and ids to dt-based parsing methods. The rotator driver has a limit table to get
size limit of input picture. Each SoCs has slightly different limit value
compared with any others.
For example, exynos4210's max_size of RGB888 is 16k x 16k. But, others have
8k x 8k. Another example the exynos5250 should have multiple of 2 pixel size
for its X/Y axis. Thus, we should keep different tables for each of them.
This patch also includes desciptions of each nodes for the rotator and specifies
a example how to bind it.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Exynos5250 G2D IP requires only the gate clock. Update the
binding documentation accordingly.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Inki Dae <inki.dae@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
