This implements SOCK_DESTROY for TCP sockets. It causes all
blocking calls on the socket to fail fast with ECONNABORTED and
causes a protocol close of the socket. It informs the other end
of the connection by sending a RST, i.e., initiating a TCP ABORT
as per RFC 793. ECONNABORTED was chosen for consistency with
FreeBSD.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a SOCK_DESTROY operation, a destroy function
pointer to sock_diag_handler, and a diag_destroy function
pointer. It does not include any implementation code.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements an ILA tanslation table. This table can be
configured with identifier to locator mappings, and can be be queried
to resolve a mapping. Queries can be parameterized based on interface,
direction (incoming or outoing), and matching locator. The table is
implemented using rhashtable and is configured via netlink (through
"ip ila .." in iproute).
The table may be used as alternative means to do do ILA tanslations
other than the lw tunnels
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The start callback allows the caller to set up a context for the
dump callbacks. Presumably, the context can then be destroyed in
the done callback.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tcp_send_sendpage and tcp_sendmsg we check the route capabilities to
determine if checksum offload can be performed. This check currently
does not take the IP protocol into account for devices that advertise
only one of NETIF_F_IPV6_CSUM or NETIF_F_IP_CSUM. This patch adds a
function to check capabilities for checksum offload with a socket
called sk_check_csum_caps. This function checks for specific IPv4 or
IPv6 offload support based on the family of the socket.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the
set of features for offloading all checksums. This is a mask of the
checksum offload related features bits. It is incorrect to set both
NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for
features of a device.
This patch:
- Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where
NETIF_F_ALL_CSUM is being used as a mask).
- Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to
use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
switchdev drivers need to know the netdev on which the switchdev op was
invoked. For example, the STP state of a VLAN interface configured on top
of a port can change while being member in a bridge. In this case, the
underlying driver should only change the STP state of that particular
VLAN and not of all the VLANs configured on the port.
However, current switchdev infrastructure only passes the port netdev down
to the driver. Solve that by passing the original device down to the
driver as part of the required switchdev object / attribute.
This doesn't entail any change in current switchdev drivers. It simply
enables those supporting stacked devices to know the originating device
and act accordingly.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-12-11
Here's another set of Bluetooth & 802.15.4 patches for the 4.5 kernel:
- 6LoWPAN debugfs support
- New 802.15.4 driver for ADF7242 MAC IEEE802154
- Initial code for 6LoWPAN Generic Header Compression (GHC) support
- Refactor Bluetooth LE scan & advertising behind dedicated workqueue
- Cleanups to Bluetooth H:5 HCI driver
- Support for Toshiba Broadcom based Bluetooth controllers
- Use continuous scanning when establishing Bluetooth LE connections
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a static inline function ipv6_addr_prefix_copy which
copies a ipv6 address prefix(argument pfx) into the ipv6 address prefix.
The prefix len is given by plen as bits. This function mainly based on
ipv6_addr_prefix which copies one address prefix from address into a new
ipv6 address destination and zero all other address bits.
The difference is that ipv6_addr_prefix_copy don't get a prefix from an
ipv6 address, it sets a prefix to an ipv6 address with keeping other
address bits. The use case is for context based address compression
inside 6LoWPAN IPHC header which keeping ipv6 prefixes inside a context
table to lookup address-bits without sending them.
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: Łukasz Duda <lukasz.duda@nordicsemi.no>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch will introduce a 6lowpan entry into the debugfs if enabled.
Inside this 6lowpan directory we create a subdirectories of all 6lowpan
interfaces to offer a per interface debugfs support.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduces register and unregister functionality for lowpan
interfaces. While register a lowpan interface there are several things
which need to be initialize by the 6lowpan subsystem. Upcoming
functionality need to register/unregister per interface components e.g.
debugfs entry.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This flag just tells us whether hdev->adv_instances is empty or not.
We can equally well use the list_empty() function to get this
information.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The request to update HCI during power on is always coming either from
hdev->req_workqueue or through an ioctl, so it's safe to use
hci_req_sync for it. This way we also eliminate potential races with
incoming mgmt commands or other actions while powering on.
Part of this refactoring is the splitting of mgmt_powered() into
mgmt_power_on() and __mgmt_power_off() functions. The main reason is
the different requirements as far as hdev locking is concerned, as
highlighted with the __ prefix of the power off API.
Since the power on in the case of clearing the AUTO_OFF flag cannot be
done synchronously in the set_powered mgmt handler, the hci_power_on
work callback is extended to cover this (which also simplifies the
set_powered helper a lot).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the other discoverable changes are behind req_workqueue now it
only makes sense to move the discoverable timeout there as well.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The discoverable mode is intrinsically linked with the connectable
mode e.g. through sharing the same HCI command (Write Scan Enable) for
BR/EDR. It makes therefore sense to move it to hci_request.c and run
the changes through the same hdev->req_workqueue.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This way the connectable changes are synchronized against each other,
which helps avoid potential races. The connectable mode is also linked
together with LE advertising which makes is more convenient to have it
behind the same workqueue.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This paves the way for eventually performing advertising changes
through the hdev->req_workqueue. Some new APIs need to be exposed from
mgmt.c to hci_request.c and vice-versa, but many of them will go away
once hdev->req_workqueue gets used.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since Add/Remove Device perform the page scan updates independently
from the HCI command completion we've introduced a potential race when
multiple mgmt commands are queued. Doing the page scan updates through
the req_workqueue ensures that the state changes are performed in a
race-free manner.
At the same time, to make the request helper more widely usable,
extend it to also cover Inquiry Scan changes since those are behind
the same HCI command. This is also reflected in the new name of the
API as well as the work struct name.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Introduce sock->sk_cgrp_data which is a struct sock_cgroup_data.
->sk_cgroup_prioidx and ->sk_classid are moved into it. The struct
and its accessors are defined in cgroup-defs.h. This is to prepare
for overloading the fields with a cgroup pointer.
This patch mostly performs equivalent conversions but the followings
are noteworthy.
* Equality test before updating classid is removed from
sock_update_classid(). This shouldn't make any noticeable
difference and a similar test will be implemented on the helper side
later.
* sock_update_netprioidx() now takes struct sock_cgroup_data and can
be moved to netprio_cgroup.h without causing include dependency
loop. Moved.
* The dummy version of sock_update_netprioidx() converted to a static
inline function while at it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
netprio builds per-netdev contiguous priomap array which is indexed by
css->id. The array is allocated using kzalloc() effectively limiting
the maximum ID supported to some thousand range. This patch caps the
maximum supported css->id to USHRT_MAX which should be way above what
is actually useable.
This allows reducing sock->sk_cgrp_prioidx to u16 from u32. The freed
up part will be used to overload the cgroup related fields.
sock->sk_cgrp_prioidx's position is swapped with sk_mark so that the
two cgroup related fields are adjacent.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
CC: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 0d76d6e8b2 and merge
commit c402293bd7, reversing changes made
to c89359a42e.
The virtio-vsock device specification is not finalized yet. Michael
Tsirkin voiced concerned about merging this code when the hardware
interface (and possibly the userspace interface) could still change.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since no more DSA driver uses the polling callback, and since
the phylib handles the link detection, remove the link polling
work and timer code.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
needing to reshuffle and fix some bugs. I merged mac80211
to get the right base for some of these changes.
* new mac80211 API for upcoming driver changes: EOSP handling,
key iteration
* scan abort changes allowing to cancel an ongoing scan
* VHT IBSS 80+80 MHz support
* re-enable full AP client state tracking after fixes
* various small fixes (that weren't relevant for mac80211)
* various cleanups
-----BEGIN PGP SIGNATURE-----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=+5dd
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-12-07' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This pull request got a bit bigger than I wanted, due to
needing to reshuffle and fix some bugs. I merged mac80211
to get the right base for some of these changes.
* new mac80211 API for upcoming driver changes: EOSP handling,
key iteration
* scan abort changes allowing to cancel an ongoing scan
* VHT IBSS 80+80 MHz support
* re-enable full AP client state tracking after fixes
* various small fixes (that weren't relevant for mac80211)
* various cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement new functionality for aborting an ongoing scan.
Add NL80211_CMD_ABORT_SCAN to the nl80211 interface. After
aborting the scan, driver shall provide the scan status by
calling cfg80211_scan_done().
Reviewed-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Vidyullatha Kanchanapally <vkanchan@qti.qualcomm.com>
Signed-off-by: Sunil Dutt <usdutt@qti.qualcomm.com>
[change command to take wdev instead of netdev so that it
can be used on p2p-device scans]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add new VIF flag, that will allow get NOA update
notification when driver will request this, even
this is not pure P2P vif (eg. STA vif).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
add ieee80211_iter_keys_rcu() to iterate over uploaded
keys in atomic context (when rcu is locked)
The station removal code removes the keys only after
calling synchronize_net(), so it's not safe to iterate
the keys at this point (and postponing the actual key
deletion with call_rcu() might result in some
badly-ordered ops calls).
Add a flag to indicate a station is being removed,
and skip the configured keys if it's set.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can happen when the driver needs to send less frames
than expected and then needs to close the SP.
Mac80211 still needs to set the more_data properly based
on its buffer state (ps_tx_buffer and buffered frames on
other TIDs).
To that end, refactor the code that delivers frames upon
uAPSD trigger frames to be able to get only the more_data
bit without actually delivering those frames in case the
driver is just asking to set a NDP with EOSP and MORE_DATA
bit properly set.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function is a very simple wrapper around another one,
just adds a few default parameters, so replace it with a
static inline instead of using EXPORT_SYMBOL, reducing
the module size slightly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some devices or drivers cannot deal with having the same station
address for different virtual interfaces, say as a client to two
virtual AP interfaces. Rather than requiring each driver with a
limitation like that to enforce it, add a hardware flag for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
I want to get the full off-channel bugfix since later code depends on
it, as well as the AP client state change so I can revert it correctly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/ethernet/renesas/ravb_main.c
kernel/bpf/syscall.c
net/ipv4/ipmr.c
All three conflicts were cases of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
* fix scanning in mac80211 to not actively scan radar
channels (from Antonio)
* fix uninitialized variable in remain-on-channel that
could lead to treating frame TX as remain-on-channel
and not sending the frame at all
* remove NL80211_FEATURE_FULL_AP_CLIENT_STATE again, it
was broken and needs more work, we'll enable it later
* fix call_rcu() induced use-after-reset/free in mesh
(that was suddenly causing issues in certain tests)
* always request block-ack window size 64 as we found
some APs will otherwise crash (really ...)
* fix P2P-Device teardown sequence to avoid restarting
with uninitialized data
-----BEGIN PGP SIGNATURE-----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=vui7
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2015-12-02' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A small set of fixes for 4.4:
* fix scanning in mac80211 to not actively scan radar
channels (from Antonio)
* fix uninitialized variable in remain-on-channel that
could lead to treating frame TX as remain-on-channel
and not sending the frame at all
* remove NL80211_FEATURE_FULL_AP_CLIENT_STATE again, it
was broken and needs more work, we'll enable it later
* fix call_rcu() induced use-after-reset/free in mesh
(that was suddenly causing issues in certain tests)
* always request block-ack window size 64 as we found
some APs will otherwise crash (really ...)
* fix P2P-Device teardown sequence to avoid restarting
with uninitialized data
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
qdisc_tree_decrease_qlen() suffers from two problems on multiqueue
devices.
One problem is that it updates sch->q.qlen and sch->qstats.drops
on the mq/mqprio root qdisc, while it should not : Daniele
reported underflows errors :
[ 681.774821] PAX: sch->q.qlen: 0 n: 1
[ 681.774825] PAX: size overflow detected in function qdisc_tree_decrease_qlen net/sched/sch_api.c:769 cicus.693_49 min, count: 72, decl: qlen; num: 0; context: sk_buff_head;
[ 681.774954] CPU: 2 PID: 19 Comm: ksoftirqd/2 Tainted: G O 4.2.6.201511282239-1-grsec #1
[ 681.774955] Hardware name: ASUSTeK COMPUTER INC. X302LJ/X302LJ, BIOS X302LJ.202 03/05/2015
[ 681.774956] ffffffffa9a04863 0000000000000000 0000000000000000 ffffffffa990ff7c
[ 681.774959] ffffc90000d3bc38 ffffffffa95d2810 0000000000000007 ffffffffa991002b
[ 681.774960] ffffc90000d3bc68 ffffffffa91a44f4 0000000000000001 0000000000000001
[ 681.774962] Call Trace:
[ 681.774967] [<ffffffffa95d2810>] dump_stack+0x4c/0x7f
[ 681.774970] [<ffffffffa91a44f4>] report_size_overflow+0x34/0x50
[ 681.774972] [<ffffffffa94d17e2>] qdisc_tree_decrease_qlen+0x152/0x160
[ 681.774976] [<ffffffffc02694b1>] fq_codel_dequeue+0x7b1/0x820 [sch_fq_codel]
[ 681.774978] [<ffffffffc02680a0>] ? qdisc_peek_dequeued+0xa0/0xa0 [sch_fq_codel]
[ 681.774980] [<ffffffffa94cd92d>] __qdisc_run+0x4d/0x1d0
[ 681.774983] [<ffffffffa949b2b2>] net_tx_action+0xc2/0x160
[ 681.774985] [<ffffffffa90664c1>] __do_softirq+0xf1/0x200
[ 681.774987] [<ffffffffa90665ee>] run_ksoftirqd+0x1e/0x30
[ 681.774989] [<ffffffffa90896b0>] smpboot_thread_fn+0x150/0x260
[ 681.774991] [<ffffffffa9089560>] ? sort_range+0x40/0x40
[ 681.774992] [<ffffffffa9085fe4>] kthread+0xe4/0x100
[ 681.774994] [<ffffffffa9085f00>] ? kthread_worker_fn+0x170/0x170
[ 681.774995] [<ffffffffa95d8d1e>] ret_from_fork+0x3e/0x70
mq/mqprio have their own ways to report qlen/drops by folding stats on
all their queues, with appropriate locking.
A second problem is that qdisc_tree_decrease_qlen() calls qdisc_lookup()
without proper locking : concurrent qdisc updates could corrupt the list
that qdisc_match_from_root() parses to find a qdisc given its handle.
Fix first problem adding a TCQ_F_NOPARENT qdisc flag that
qdisc_tree_decrease_qlen() can use to abort its tree traversal,
as soon as it meets a mq/mqprio qdisc children.
Second problem can be fixed by RCU protection.
Qdisc are already freed after RCU grace period, so qdisc_list_add() and
qdisc_list_del() simply have to use appropriate rcu list variants.
A future patch will add a per struct netdev_queue list anchor, so that
qdisc_tree_decrease_qlen() can have more efficient lookups.
Reported-by: Daniele Fucini <dfucini@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Cong Wang <cwang@twopensource.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let netdev notifier listeners know about link and slave state change.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to state notifications.
We allow caller to indicate if the notification should happen now or later,
depending on if he holds rtnl mutex or not. Introduce bond_slave_link_notify
function (similar to bond_slave_state_notify) which is later on called
with rtnl mutex and goes over slaves and executes delayed notification.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing the np->opt RCU conversion, I found that UDP/IPv6 was
using a mixture of xchg() and sk_dst_lock to protect concurrent changes
to sk->sk_dst_cache, leading to possible corruptions and crashes.
ip6_sk_dst_lookup_flow() uses sk_dst_check() anyway, so the simplest
way to fix the mess is to remove sk_dst_lock completely, as we did for
IPv4.
__ip6_dst_store() and ip6_dst_store() share same implementation.
sk_setup_caps() being called with socket lock being held or not,
we have to use sk_dst_set() instead of __sk_dst_set()
Note that I had to move the "np->dst_cookie = rt6_get_cookie(rt);"
in ip6_dst_store() before the sk_setup_caps(sk, dst) call.
This is because ip6_dst_store() can be called from process context,
without any lock held.
As soon as the dst is installed in sk->sk_dst_cache, dst can be freed
from another cpu doing a concurrent ip6_dst_store()
Doing the dst dereference before doing the install is needed to make
sure no use after free would trigger.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If tcp_send_ack() can not allocate skb, we properly handle this
and setup a timer to try later.
Use __GFP_NOWARN to avoid polluting syslog in the case host is
under memory pressure, so that pertinent messages are not lost under
a flood of useless information.
sk_gfp_atomic() can use its gfp_mask argument (all callers currently
were using GFP_ATOMIC before this patch)
We rename sk_gfp_atomic() to sk_gfp_mask() to clearly express this
function now takes into account its second argument (gfp_mask)
Note that when tcp_transmit_skb() is called with clone_it set to false,
we do not attempt memory allocations, so can pass a 0 gfp_mask, which
most compilers can emit faster than a non zero or constant value.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They don't need to be any bigger than that and with this we start a new
bitfield for tracking association runtime stuff, like zero window
situation.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses multiple problems :
UDP/RAW sendmsg() need to get a stable struct ipv6_txoptions
while socket is not locked : Other threads can change np->opt
concurrently. Dmitry posted a syzkaller
(http://github.com/google/syzkaller) program desmonstrating
use-after-free.
Starting with TCP/DCCP lockless listeners, tcp_v6_syn_recv_sock()
and dccp_v6_request_recv_sock() also need to use RCU protection
to dereference np->opt once (before calling ipv6_dup_options())
This patch adds full RCU protection to np->opt
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry provided a syzkaller (http://github.com/google/syzkaller)
triggering a fault in sock_wake_async() when async IO is requested.
Said program stressed af_unix sockets, but the issue is generic
and should be addressed in core networking stack.
The problem is that by the time sock_wake_async() is called,
we should not access the @flags field of 'struct socket',
as the inode containing this socket might be freed without
further notice, and without RCU grace period.
We already maintain an RCU protected structure, "struct socket_wq"
so moving SOCKWQ_ASYNC_NOSPACE & SOCKWQ_ASYNC_WAITDATA into it
is the safe route.
It also reduces number of cache lines needing dirtying, so might
provide a performance improvement anyway.
In followup patches, we might move remaining flags (SOCK_NOSPACE,
SOCK_PASSCRED, SOCK_PASSSEC) to save 8 bytes and let 'struct socket'
being mostly read and let it being shared between cpus.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a cleanup to make following patch easier to
review.
Goal is to move SOCK_ASYNC_NOSPACE and SOCK_ASYNC_WAITDATA
from (struct socket)->flags to a (struct socket_wq)->flags
to benefit from RCU protection in sock_wake_async()
To ease backports, we rename both constants.
Two new helpers, sk_set_bit(int nr, struct sock *sk)
and sk_clear_bit(int net, struct sock *sk) are added so that
following patch can change their implementation.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit ab450605b3.
In IPv6, we cannot inherit the dst of the original dst. ndisc packets
are IPv6 packets and may take another route than the original packet.
This patch breaks the following scenario: a packet comes from eth0 and
is forwarded through vxlan1. The encapsulated packet triggers an NS
which cannot be sent because of the wrong route.
CC: Jiri Benc <jbenc@redhat.com>
CC: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The memory barrier in the helper wq_has_sleeper is needed by just
about every user of waitqueue_active. This patch generalises it
by making it take a wait_queue_head_t directly. The existing
helper is renamed to skwq_has_sleeper.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a fragmented multicast packet is received on an ethernet device which
has an active macvlan on top of it, each fragment is duplicated and
received both on the underlying device and the macvlan. If some
fragments for macvlan are processed before the whole packet for the
underlying device is reassembled, the "overlapping fragments" test in
ip6_frag_queue() discards the whole fragment queue.
To resolve this, add device ifindex to the search key and require it to
match reassembling multicast packets and packets to link-local
addresses.
Note: similar patch has been already submitted by Yoshifuji Hideaki in
http://patchwork.ozlabs.org/patch/220979/
but got lost and forgotten for some reason.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-11-23
Here's the first bluetooth-next pull request for the 4.5 kernel.
- Add new Get Advertising Size Information management command
- Add support for new system note message type on monitor channel
- Refactor LE scan changes behind separate workqueue to avoid races
- Fix issue with privacy feature when powering on adapter
- Various minor fixes & cleanups here and there
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Rainer Weikusat <rweikusat@mobileactivedefense.com> writes:
An AF_UNIX datagram socket being the client in an n:1 association with
some server socket is only allowed to send messages to the server if the
receive queue of this socket contains at most sk_max_ack_backlog
datagrams. This implies that prospective writers might be forced to go
to sleep despite none of the message presently enqueued on the server
receive queue were sent by them. In order to ensure that these will be
woken up once space becomes again available, the present unix_dgram_poll
routine does a second sock_poll_wait call with the peer_wait wait queue
of the server socket as queue argument (unix_dgram_recvmsg does a wake
up on this queue after a datagram was received). This is inherently
problematic because the server socket is only guaranteed to remain alive
for as long as the client still holds a reference to it. In case the
connection is dissolved via connect or by the dead peer detection logic
in unix_dgram_sendmsg, the server socket may be freed despite "the
polling mechanism" (in particular, epoll) still has a pointer to the
corresponding peer_wait queue. There's no way to forcibly deregister a
wait queue with epoll.
Based on an idea by Jason Baron, the patch below changes the code such
that a wait_queue_t belonging to the client socket is enqueued on the
peer_wait queue of the server whenever the peer receive queue full
condition is detected by either a sendmsg or a poll. A wake up on the
peer queue is then relayed to the ordinary wait queue of the client
socket via wake function. The connection to the peer wait queue is again
dissolved if either a wake up is about to be relayed or the client
socket reconnects or a dead peer is detected or the client socket is
itself closed. This enables removing the second sock_poll_wait from
unix_dgram_poll, thus avoiding the use-after-free, while still ensuring
that no blocked writer sleeps forever.
Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com>
Fixes: ec0d215f94 ("af_unix: fix 'poll for write'/connected DGRAM sockets")
Reviewed-by: Jason Baron <jbaron@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some boards have a gpio line tied to the switch reset pin. Allow this
gpio to be retrieved from the device tree, and take the switch out of
reset before performing the probe.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Get Advertising Size Information command allows to retrieve size
information for advertising data and scan response data fields depending
on the selected flags. This is useful if applications want to know the
available size ahead of time.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
