sh73a0 has divisor[12] setting as 1/7 on FRQCRA.
Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch improves the state of the AG5 clock
framework support. The main clock parent is
automatically detected, but most of the clocks
are not used by any driver or subsystem at this
point. More work is needed for support of multi
media hardware such as FSI and/or LCDC/MIPI-DSI.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch permuted clock arrays in the order of MSTP
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Just add port multiplex settings to enable i2c modules.
Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This consists of platform device resources/data for the board, and
simple clvdev entry for MSTP bit for keysc module.
This support only 49 of 80 key-switches on the board.
Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Ag5evm board now uses gpio api to initialize pins and peripherals.
Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
PFC definitions for sh73a0 to support GPIO and pinmux handling.
Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently the entry macros are all globbed together, this simply splits
them out in to their insular variants. Future work such as the GIC
generalization will replace some of these and tidy the abstraction up
further.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds initial support for Renesas SH-Mobile AG5.
At this point the AG5 CPU support is limited to the ARM
core, SCIF serial and a CMT timer together with L2 cache
and the GIC. The AG5EVM board also supports Ethernet.
Future patches will add support for GPIO, INTCS, CPGA
and platform data / driver updates for devices such as
IIC, LCDC, FSI, KEYSC, CEU and SDHI among others.
The code in entry-macro.S will be cleaned up when the
ARM IRQ demux code improvements have been merged.
Depends on the AG5EVM mach-type recently registered but
not yet present in arch/arm/tools/mach-types.
As the AG5EVM board comes with 512MiB memory it is
recommended to turn on HIGHMEM.
Many thanks to Yoshii-san for initial bring up.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently each one of the CPUs manually selects the same feature set, and
there's a reasonable expectation that none of these will change for
future CPUs in the SH-Mobile / R-Mobile family, so we move those over to
the top-level ARCH_SHMOBILE.
While we're at it, all of the CPUs support optional GPIOs via the PFC,
do not have I/O ports, and expect sparse IRQ, so we bring the
configuration in line across the board.
This more or less brings the ARM-based parts in sync with their SH
counterparts.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The addition of CONFIG_SECURITY_DMESG_RESTRICT resulted in a build
failure when CONFIG_PRINTK=n. This is because the capabilities code
which used the new option was built even though the variable in question
didn't exist.
The patch here fixes this by moving the capabilities checks out of the
LSM and into the caller. All (known) LSMs should have been calling the
capabilities hook already so it actually makes the code organization
better to eliminate the hook altogether.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
arm: omap1: devices: need to return with a value
OMAP1: camera.h: add missing include
omap: dma: Add read-back to DMA interrupt handler to avoid spuriousinterrupts
OMAP2: Devkit8000: Fix mmc regulator failure
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (w83795) Check for BEEP pin availability
hwmon: (w83795) Clear intrusion alarm immediately
hwmon: (w83795) Read the intrusion state properly
hwmon: (w83795) Print the actual temperature channels as sources
hwmon: (w83795) List all usable temperature sources
hwmon: (w83795) Expose fan control method
hwmon: (w83795) Fix fan control mode attributes
hwmon: (lm95241) Check validity of input values
hwmon: Change mail address of Hans J. Koch
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: sysfs: fix printk warnings
PCI: fix pci_bus_alloc_resource() hang, prefer positive decode
PCI: read current power state at enable time
PCI: fix size checks for mmap() on /proc/bus/pci files
x86/PCI: coalesce overlapping host bridge windows
PCI hotplug: ibmphp: Add check to prevent reading beyond mapped area
Make sure I2C adapters being registered have the required struct
fields set. If they don't, problems will happen later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
It's about time to make it clear that i2c_adapter.id is deprecated.
Hopefully this will remind the last user to move over to a different
strategy.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Drivers don't need to include <linux/i2c-id.h>, especially not when
they don't use anything that header file provides.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Michael Hunold <michael@mihu.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Delete unused I2C adapter IDs. Special cases are:
* I2C_HW_B_RIVA was still set in driver rivafb, however no other
driver is ever looking for this value, so we can safely remove it.
* I2C_HW_B_HDPVR is used in staging driver lirc_zilog, however no
adapter ID is ever set to this value, so the code in question never
runs. As the code additionally expects that I2C_HW_B_HDPVR may not
be defined, we can delete it now and let the lirc_zilog driver
maintainer rewrite this piece of code.
Big thanks for Hans Verkuil for doing all the hard work :)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
A few new i2c-drivers came into the kernel which clear the clientdata-pointer
on exit. This is obsolete meanwhile, so fix it and hope the word will spread.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Alan Cox <alan@linux.intel.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Move the logging bits from kernel.h into printk.h so that
there is a bit more logical separation of the generic from
the printk logging specific parts.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The fix in commit 6b4e81db25 ("i8k: Tell gcc that *regs gets
clobbered") to work around the gcc miscompiling i8k.c to add "+m
(*regs)" caused register pressure problems and a build failure.
Changing the 'asm' statement to 'asm volatile' instead should prevent
that and works around the gcc bug as well, so we can remove the "+m".
[ Background on the gcc bug: a memory clobber fails to mark the function
the asm resides in as non-pure (aka "__attribute__((const))"), so if
the function does nothing else that triggers the non-pure logic, gcc
will think that that function has no side effects at all. As a result,
callers will be mis-compiled.
Adding the "+m" made gcc see that it's not a pure function, and so
does "asm volatile". The problem was never really the need to mark
"*regs" as changed, since the memory clobber did that part - the
problem was just a bug in the gcc "pure" function analysis - Linus ]
Signed-off-by: Jim Bos <jim876@xs4all.nl>
Acked-by: Jakub Jelinek <jakub@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On the W83795ADG, there's a single pin for BEEP and OVT#, so you
can't have both. Check the configuration and don't create beep
attributes when BEEP pin is not available.
The W83795G has a dedicated BEEP pin so the functionality is always
available there.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
When asked to clear the intrusion alarm, do so immediately. We have to
invalidate the cache to make sure the new status will be read. But we
also have to read from the status register once to clear the pending
alarm, as writing to CLR_CHS surprising won't clear it automatically.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
We can't read the intrusion state from the real-time alarm registers
as we do for all other alarm flags, because real-time alarm bits don't
stick (by definition) and the intrusion state has to stick until
explicitly cleared (otherwise it has little value.)
So we have to use the interrupt status register instead, which is read
from the same address but with a configuration bit flipped in another
register.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Don't expose raw register values to user-space. Decode and encode
temperature channels selected as temperature sources as needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Temperature sources are not correlated directly with temperature
channels. A look-up table is required to find out which temperature
sources can be used depending on which temperature channels (both
analog and digital) are enabled.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Expose fan control method (DC vs. PWM) using the standard sysfs
attributes. I've made it read-only as the board should be wired for
a given mode, the BIOS should have set up the chip for this mode, and
you shouldn't have to change it. But it would be easy enough to make
it changeable if someone comes up with a use case.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
There were two bugs:
* Speed cruise mode was improperly reported for all fans but fan1.
* Fan control method (PWM vs. DC) was mixed with the control mode.
It will be added back as a separate attribute, as per the standard
sysfs interface.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
This clears the following build-time warnings I was seeing:
drivers/hwmon/lm95241.c: In function "set_interval":
drivers/hwmon/lm95241.c:132:15: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_max2":
drivers/hwmon/lm95241.c:278:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_max1":
drivers/hwmon/lm95241.c:277:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_min2":
drivers/hwmon/lm95241.c:249:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_min1":
drivers/hwmon/lm95241.c:248:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_type2":
drivers/hwmon/lm95241.c:220:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
drivers/hwmon/lm95241.c: In function "set_type1":
drivers/hwmon/lm95241.c:219:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result
This also fixes a small race in set_interval() as a side effect: by
working with a temporary local variable we prevent data->interval from
being accessed at a time it contains the interval value in the wrong
unit.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Davide Rizzo <elpa.rizzo@gmail.com>
My old mail address doesn't exist anymore. This changes all occurrences
to my new address.
Signed-off-by: Hans J. Koch <hjk@hansjkoch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cast pci_resource_start() and pci_resource_len() to u64 for printk.
drivers/pci/pci-sysfs.c:753: warning: format '%16Lx' expects type 'long long unsigned int', but argument 9 has type 'resource_size_t'
drivers/pci/pci-sysfs.c:753: warning: format '%16Lx' expects type 'long long unsigned int', but argument 10 has type 'resource_size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6:
fsl-diu-fb: drop dead ioctl define
MAINTAINERS: Add an fbdev git tree entry.
OMAP: DSS: Fix documentation regarding 'vram' kernel parameter
OMAP: VRAM: Fix boot-time memory allocation
OMAP: VRAM: improve VRAM error prints
sisfb: limit POST memory test according to PCI resource length
fbdev: sh_mobile_lcdc: use correct number of modes, when using the default
fbdev: sh_mobile_lcdc: use the standard CEA-861 720p timing
fbdev: sh_mobile_hdmi: properly clean up modedb on monitor unplug
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: intc: Fix up build failure introduced by radix tree changes.
MAINTAINERS: update the sh git tree entry.
sh: clkfwk: fix up compiler warnings.
sh: intc: Fix up initializers for gcc 4.5.
rtc: rtc-sh - fix a memory leak
* 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
ARM: mach-shmobile: ap4evb: add fsib 44100Hz rate
MAINTAINERS: update the ARM SH-Mobile git tree entry.
ARM: mach-shmobile: ap4evb: Mark NOR boot loader partitions read-only.
ARM: mach-shmobile: intc-sh7372: fix interrupt number
This area of the code has always been a bit delicate due to the
subtleties of lock ordering. The problem is that for "normal"
alloc/dealloc, we always grab the inode locks first and the rgrp lock
later.
In order to ensure no races in looking up the unlinked, but still
allocated inodes, we need to hold the rgrp lock when we do the lookup,
which means that we can't take the inode glock.
The solution is to borrow the technique already used by NFS to solve
what is essentially the same problem (given an inode number, look up
the inode carefully, checking that it really is in the expected
state).
We cannot do that directly from the allocation code (lock ordering
again) so we give the job to the pre-existing delete workqueue and
carry on with the allocation as normal.
If we find there is no space, we do a journal flush (required anyway
if space from a deallocation is to be released) which should block
against the pending deallocations, so we should always get the space
back.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
The radix tree retry logic got a bit of an overhaul and subsequently
broke the virtual IRQ subgroup build. Simply switch over to
radix_tree_deref_retry() as per the filemap changes, which the virq
lookup logic was modelled after in the first place.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The fsl-diu-fb driver no longer uses this define, and we have a common one
to cover this already (FBIO_WAITFORVSYNC).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that there's an fbdev git tree (this is also what is pulled in to
-next), stub it in to the MAINTAINERS entry.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
