Sometimes drivers need to execute one-off actions in their error handling
or device teardown paths. An example would be toggling a GPIO line to
reset the controlled device into predefined state.
To allow performing such actions when using managed resources let's allow
adding them to stack/group of devres resources.
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add the necessary code to create the needed platformdata from devicetree
informations.
The interrupt mode of the chip is not set via devicetree, as it is not
a property of the hardware but instead only a preferred type of operation.
This should probably be made settable via configfs in the future.
The option set as default is the mode the datasheet mentions as default.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When supporting devicetree the platformdata may not necessarily come
from the dev but may be generated in the driver instead.
Therefore keep the pointer in the driver struct instead of using
dev.platform_data.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Devicetree based platforms don't handle device callbacks very well
and until now no board has come along that needs more extended hwinit
than pulling the rst gpio high.
Therefore pull the reset handling directly into the driver and remove
the callbacks from the driver.
If extended device setup is needed at some later point, power-sequences
would probably be the solution of choice.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Previously the gpio was not configured at all.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This enables autoloading of tsc2005 driver when is compiled as a module.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tegra only supports, and always enables, device tree. Remove all ifdefs
and runtime checks for DT support from the driver. Platform data is
therefore no longer required. Delete the header that defines it, and
rework the driver to parse the device tree directly into struct
tegra_kbc.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
To properly setup event parameters for emulated events, pass
the appropriate flag to the slot initialization function. Also,
all MT-related events should be setup before initialization.
Incidentally, this solves the issue of doubly filtered pointer
events.
Reported-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The pointer emulation events are derived from contact values that
have already been filtered, so send the emulated events as is.
Reported-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make the constants referring to range and bandwidth public so they can
be used when initializing the platform data fields in the platform code.
Fix also some comments regarding the unit of measurement to use for the
range and bandwidth fields, the values are not actually expected to be
in G or HZ, the code in bma150.c just uses the BMA150_RANGE_xxx and
BMA150_BW_xxx constants like they are with no translation from actual
values in G or HZ.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Antonio Ospite <ao2@amarulasolutions.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When PM_RUNTIME is not defined, pm_runtime_get_sync() returns 1, see
include/linux/pm_runtime.c::__pm_runtime_resume(), and the check of the
return value was overlooking this, in this case bma150_open() would
return 1 which is not expected by upper layers.
Maybe the check for != -ENOSYS (Function not implemented) was meant to
cover this, but pm_runtime_get_sync() does not return this value.
For now fix the issue locally by checking explicitly for negative return
values.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Antonio Ospite <ao2@amarulasolutions.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Separate out the common trackstick probe/setup sequences, then call them
from each of the v3 init functions.
Credits: Emmanual Thome furnished the information on the trackstick init
and how it affected the report format.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Tested-by: Dave Turvene <dturvene@dahetral.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Rushmore touchpads are found on Dell E6230/E6430/E6530. They use the V3
protocol with slightly tweaked init sequences and report formats.
The E7 report is 73 03 0a, and the EC report is 88 08 1d
Credits: Emmanuel Thome reported the MT bitmap changes.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Tested-by: Dave Turvene <dturvene@dahetral.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A number of different ALPS touchpad protocols can reuse
alps_process_touchpad_packet_v3() with small tweaks to the bitfield
decoding. Create a new priv->decode_fields() callback that handles the
per-model differences.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Tested-by: Dave Turvene <dturvene@dahetral.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Newer touchpads use different constants, so make them runtime-
configurable.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Tested-by: Dave Turvene <dturvene@dahetral.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pinnacle class devices should return "88 07 xx" or "88 08 xx" when
entering command mode. If either the first byte or the second byte is
invalid, return an error.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Tested-by: Dave Turvene <dturvene@dahetral.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The official ALPS driver uses the EC report, not the E7 report, to detect
these devices. Also, they check for a range of values; the original
table-based code only checked for two specific ones.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Tested-by: Dave Turvene <dturvene@dahetral.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This allows alps_identify() to override these settings based on the
device characteristics, if it is ever necessary.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Tested-by: Dave Turvene <dturvene@dahetral.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In anticipation of adding more ALPS protocols and more per-device quirks,
use function pointers instead of switch statements to call functions that
differ from one device to the next.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Tested-by: Dave Turvene <dturvene@dahetral.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If the E6 report test passes, get the E7 and EC reports right away and
then try to match an entry in the table.
Pass in the alps_data struct, so that the detection code will be able to
set operating parameters based on information found during detection.
Change the version (psmouse->model) to report the protocol version only,
in preparation for supporting models that do not show up in the ID table.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Tested-by: Dave Turvene <dturvene@dahetral.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Several ALPS driver init sequences repeat a command three times, then
issue PSMOUSE_CMD_GETINFO to read the result. Move this into a helper
function to simplify the code.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Tested-by: Dave Turvene <dturvene@dahetral.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This will minimize the number of forward declarations needed when
alps_get_model() starts assigning function pointers.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Tested-by: Dave Turvene <dturvene@dahetral.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Not every type of ALPS touchpad is well-suited to table-based detection.
Start moving the various alps_model_data attributes into the alps_data
struct so that we don't need a unique table entry for every possible
permutation of protocol version, flags, byte0/mask0, etc.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Tested-by: Dave Turvene <dturvene@dahetral.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds support for the Cypress APA Smbus Trackpad type,
which uses a modified register map that fits within the
limitations of the smbus protocol.
Devices that use this protocol include:
CYTRA-116001-00 - Samsung Series 5 550 Chromebook trackpad
CYTRA-103002-00 - Acer C7 Chromebook trackpad
CYTRA-101003-00 - HP Pavilion 14 Chromebook trackpad
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Investigating the following gesture highlighted two slight implementation
errors with choosing which slots to report in which slot when multiple
contacts are present:
Action SGM AGM (MTB slot:Contact)
1. Touch contact 0 (0:0)
2. Touch contact 1 (0:0, 1:1)
3. Lift contact 0 (1:1)
4. Touch contacts 2,3 (0:2, 1:3)
In step 4, slot 1 was not being cleared first, which means the same
tracking ID was being used for reporting both the old contact 1 and the
new contact 3. This could result in "drumroll", where the old contact 1
would appear to suddenly jump to new finger 3 position.
Similarly, if contacts 2 & 3 are not detected at the same sample, step 4
is split into two:
Action SGM AGM (MTB slot:contact)
1. Touch contact 0 (0:0)
2. Touch contact 1 (0:0, 1:1)
3. Lift contact 0 (1:1)
4. Touch contact 2 (0:2, 1:1)
5. Touch contact 3 (0:2, 1:3)
In this case, there was also a bug. In step 4, when contact 1 moves from
SGM to AGM and contact 2 is first reported in SGM, slot 0 was actually
empty. So slot 0 can be used to report the new SGM (contact 0),
immediately. Since it was empty, contact 2 in slot 0 will get a new
tracking ID.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When removing the !S390 dependency from drivers/input/Kconfig
a couple of drivers don't compile because they have a dependency
on GENERIC_HARDIRQS. So add the missing dependencies.
Fixes e.g. this one:
drivers/input/keyboard/lm8323.c: In function ‘lm8323_suspend’:
drivers/input/keyboard/lm8323.c:801:2: error: implicit declaration of function ‘irq_set_irq_wake’
[-Werror=implicit-function-declaration]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It is time to switch to system wq instead creating a queue for the driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Convert the probe to use devm_*. At the same time reorder the calls
so we will register the input device as the last step when the driver
is loaded.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This device is a direct pipe from "hardware" to the input event subsystem,
allowing us to avoid having to route "keypad" style events through an
AT keyboard driver (gross!).
As with the other submissions this driver is cross architecture.
Signed-off-by: Mike A. Chan <mikechan@google.com>
[Tided up to work on x86]
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Yunhong Jiang <yunhong.jiang@intel.com>
Signed-off-by: Xiaohui Xin <xiaohui.xin@intel.com>
Signed-off-by: Jun Nakajima <jun.nakajima@intel.com>
Signed-off-by: Bruce Beare <bruce.j.beare@intel.com>
[Ported to 3.4]
Signed-off-by: Tom Keel <thomas.keel@intel.com>
[Cleaned up for 3.7 and submission]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Postpone claiming the port until the device is opened, instead of doing
that when the driver is loaded.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We have been using -EBUSY where we should have used -EIO or -ENOMEM,
so let's fix that and also add some diagnostic messages.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This will place the joystick's input device into propoer place in sysfs
hierarchy as long as th port has device assigned to it (i.e. it is not
legacy port).
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On resume from suspend there is a possibility for multi-byte scancodes
to be handled incorrectly. atkbd_reconnect disables the processing of
scancodes in software by calling atkbd_disable, but the keyboard may
still be active because no disconnect command was sent. Later, software
handling is re-enabled. If a multi-byte scancode sent from the keyboard
straddles the re-enable, only the latter byte(s) will be handled.
In practice, this leads to cases where multi-byte break codes (ex. "e0
4d" - break code for right-arrow) are misread as make codes ("4d" - make
code for numeric 6), leading to one or more unwanted, untyped characters
being interpreted.
The solution implemented here involves sending command f5 (reset
disable) to the keyboard prior to disabling software handling of codes.
Later, the command to re-enable the keyboard is sent only after we are
prepared to handle scancodes.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It is time to switch to system wq instead creating a queue for the driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This simplifies error handling and eliminates the need for implementing
remove() method.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch introduces a driver for Cypress All Points Addressable
I2C Trackpad, including the ones in 2012 Samsung Chromebooks.
This device is compatible with MT protocol type B, providing identifiable
contacts.
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
devm_* APIs are device managed and make the exit and clean up code
simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Laxman Dewangan<ldewangan@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tegra KBC driver have the default key mapping for 16x8 configuration.
The key mapping can be provided through platform data or through DT
and the mapping varies from platform to platform, hence this default
mapping is not so useful. Remove the default mapping to reduce the code
lines of the driver.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The NVIDIA's Tegra KBC has maximum 24 pins to make matrix keypad.
Any pin can be configured as row or column. The maximum column pin
can be 8 and maximum row pin can be 16.
Remove the assumption that all first 16 pins will be used as row
and remaining as columns and Add the property for configuring pins
to either row or column from DT. Update the devicetree binding
document accordingly.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use devm_* for memory, clock, irq, input device allocation. This reduces
code for freeing these resources.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix the following build warning when building driver with CONFIG_PM_SLEEP
not selected.
tegra-kbc.c:360:13: warning: 'tegra_kbc_set_keypress_interrupt' defined but not used [-Wunused-function]
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds keyreset functionality to the sysrq driver. It allows
certain button/key combinations to be used in order to trigger emergency
reboots.
Redefining the '__weak platform_sysrq_reset_seq' variable is required
to trigger the feature. Alternatively keys can be passed to the driver
via a module parameter.
This functionality comes from the keyreset driver submitted by
Arve Hjønnevåg in the Android kernel.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver, submitted on behalf of Cypress Semiconductor Corporation and
additional contributors, provides support for the Cypress PS/2 Trackpad.
Original code contributed by Dudley Du (Cypress Semiconductor Corporation),
modified by Kamal Mostafa and Kyle Fazzari.
BugLink: http://launchpad.net/bugs/978807
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Kyle Fazzari <git@status.e4ward.com>
Signed-off-by: Mario Limonciello <mario_limonciello@dell.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Acked-by: Herton Krzesinski <herton.krzesinski@canonical.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Reviewed-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch brings wacom driver in-sync with input-mt changes
made in release 3.7.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
