The DTK-2451 and DTH-2452 have a buggy HID descriptor which incorrectly
contains a Cintiq-like report, complete with pen tilt, rotation, twist, serial
number, etc. The hardware doesn't actually support this data but our driver
duitifully sets up the device as though it does. To ensure userspace has a
correct view of devices without updated firmware, we clean up this incorrect
data in wacom_setup_device_quirks.
We're also careful to clear the WACOM_QUIRK_TOOLSERIAL flag since its presence
causes the driver to wait for serial number information (via
wacom_wac_pen_serial_enforce) that never comes, resulting in
the pen being non-responsive.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Fixes: 8341720642 ("HID: wacom: Queue events with missing type/serial data for later processing")
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The touch sensors on the 2nd-gen Intuos tablets don't use a 4096x4096
sensor like other similar tablets (3rd-gen Bamboo, Intuos5, etc.).
The incorrect maximum XY values don't normally affect userspace since
touch input from these devices is typically relative rather than
absolute. It does, however, cause problems when absolute distances
need to be measured, e.g. for gesture recognition. Since the resolution
of the touch sensor on these devices is 10 units / mm (versus 100 for
the pen sensor), the proper maximum values can be calculated by simply
dividing by 10.
Fixes: b5fd2a3e92 ("Input: wacom - add support for three new Intuos devices")
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Detecting the number of supported touches for a particular device used
to be tricky, both because early forms of the driver didn't have a very
good HID parser and because early hardware didn't always advertise the
actual number. At the time, we added a block of code which would ensure
that touch_max would always be equal to at least 1 on any touch device,
and relied on setting touch_max to e.g. 2 only for the multitouch-capable
exceptions.
The common case has since flipped, and the driver and descriptors can
reliably detect the number of touches supported by modern sensors.
Because of this, it makes sense to remove the fixup code and instead
place static declarations of "touch_max = 1" for these old devices. It
isn't entirely clear if all 2-finger devices actually report a maximum
number of touches so we leave these declarations still in place.
For the eagle-eyed, the "> BAMBOO_PT" condition was originally equivalent
to ">= TABLETPC", which is what the intent was. This commit doesn't have
to consider the types introduced in the interim since they shouldn't be
affected, hence why only the tablet PC definitions have been modified.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The 1st-generation Intuos tablets (CTL-X80) include an "in range" flag
like some professional tablets. To ensure the pen remains usable at as
large as distance as possible (and to preemptively disable touch when
it is nearby) we need to ensure that we handle these "in range" events.
Handling of tool type identification has been moved to occur only when
the pen is fully in prox rather than any time the "stylus_in_proximity"
flag changes (which is controlled by the further-out "in range" flag).
Link: https://sourceforge.net/p/linuxwacom/bugs/358/
Link: https://github.com/linuxwacom/xf86-input-wacom/issues/14
Link: https://github.com/linuxwacom/xf86-input-wacom/issues/17
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Tested-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The code path for recent Bluetooth devices omits an exit report which
resets all the values of the device.
Fixes: 4922cd26f0 ("HID: wacom: Support 2nd-gen Intuos Pro's Bluetooth classic interface")
Cc: <stable@vger.kernel.org> # 4.11
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Wacom Bluetooth reports contain multiple pen frames per report.
Each frame contains a flag indicating if the frame is valid.
Future Wacom devices with this type of report may contain HID
descriptors, add support for this usage to the generic codepath
of the Wacom driver.
Signed-off-by: Aaron Armstrong Skomra <skomra@gmail.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some Wacom devices contain contain Pen and Pad usages in
the same report. Future devices of this type may utilize
HID Descriptors.
The generic code path of the Wacom driver previously
assumed pen, touch, and pad reports were delivered in
separate reports. This patch adds support for processing
each collection of a report separately, in order to support
reports with multiple tools.
Signed-off-by: Aaron Armstrong Skomra <skomra@gmail.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adds support for the second-generation "One by Wacom" tablets. These
devices are similar to the last generation, but a slightly different size
and reporting a higher number of pressure levels.
Signed-off-by: Mx Jing <jingmingxuan@outlook.com>
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Touch toggle softkeys send a '1' while pressed and a '0' while released,
requring the kernel to keep track of wether touch should be enabled or
disabled. The code does not handle the state transitions properly,
however. If the key is pressed repeatedly, the following four states
of states are cycled through (assuming touch starts out enabled):
Press: shared->is_touch_on => 0, SW_MUTE_DEVICE => 1
Release: shared->is_touch_on => 0, SW_MUTE_DEVICE => 1
Press: shared->is_touch_on => 1, SW_MUTE_DEVICE => 0
Release: shared->is_touch_on => 1, SW_MUTE_DEVICE => 1
The hardware always properly enables/disables touch when the key is
pressed but applications that listen for SW_MUTE_DEVICE events to provide
feedback about the state will only ever show touch as being enabled while
the key is held, and only every-other time. This sequence occurs because
the fallthrough WACOM_HID_WD_TOUCHONOFF case is always handled, and it
uses the value of the *local* is_touch_on variable as the value to
report to userspace. The local value is equal to the shared value when
the button is pressed, but equal to zero when the button is released.
Reporting the shared value to userspace fixes this problem, but the
fallthrough case needs to update the shared value in an incompatible
way (which is why the local variable was introduced in the first place).
To work around this, we just handle both cases in a single block of code
and update the shared variable as appropriate.
Fixes: d793ff8187 ("HID: wacom: generic: support touch on/off softkey")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Aaron Skomra <aaron.skomra@wacom.com>
Tested-by: Aaron Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Userspace expects to receive tool type and serial number information
for the active pen in the very first kernel report, if such data is
supported by the hardware. While this expectation is not an issue for
EMR devices, AES sensors will often send several packets worth of in-
range data before relaying type/serial data to the kernel. Sending this
data "late" can result in proximity-tracking issues by xf86-input-wacom,
or an inability to distinguish different pens by input-wacom.
Options for dealing with this situation include ignoring reports from
the tablet until we get the necessary data, or using the information
from the last-seen pen instead of the (eventual) real data. Neither
option is particularly attractive: the former results in truncated
strokes and the latter causes issues with switching between pens.
This commit instead opts to queue up events with missing information
until we receive a report which contains it. At that point, we can
update the driver's state variables (id[0] and serial[0]) and replay
the queued events.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Current AES sensors relay tool type and serial number information with
a different set of usages than those prescribed by the modern (i.e.
MobileStudio Pro and newer) EMR tablet standard. To ensure the driver
properly understands these usages, we modify them to be compatible.
The identifying information is split across three consecutive fields:
a 16-bit WACOM_HID_WT_SERIALNUMBER (which is more accurately described
as WACOM_HID_WD_TOOLTYPE), a 32-bit HID_DG_TOOLSERIALNUMBER, and an
8-bit 0xFF000000 (which should be WACOM_HID_WD_SERIALHI). While we're
at it, we also define proper min/max values since may may be undefined
on some devices.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Wacom Pro Pen 3D includes a third barrel switch which is intended to
be particularly useful in applications where one frequency uses pan, zoom,
and rotate to navigate around a scene or model. The pen is compatible with
the MobileStudio Pro, 2nd-gen Intuos Pro, and Cintiq Pro. When the third
button is pressed, these devices set both the HID_DG_BARRELSWITCH and
HID_DG_BARRELSWITCH2 usages since their HID descriptors do not include a
usage specific to the button.
Rather than send both BTN_STYLUS and BTN_STYLUS2 when the third button is
pressed, userspace (libinput) has requested that we detect this condition
and report a newly-defined BTN_STYLUS3 event instead. We could define a
quirk specific to devices compatible with the Pro Pen 3D, but the liklihood
of seeing both barrel switch bits set with other pens/devices is low enough
to not worry about (pens mechanically prevent accidental activation of
multiple switches).
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 3e70969e44.
This commit causes a few problems for userspace. The most noteworthy are
problems related to the distinguishing of different pens and pointer jumps
when entering proximity. Userspace is written with the expectation that a
pen will provide its tool ID and serial number (if available) in the very
first in-prox report. By sending BTN_TOOL_PEN when the tablet starts
communicating rather than waiting until a tool ID/serial number is
available, userspace ends up treating all pens as being the same and
lacking a serial number. Similarly, userspace assumes that the first
report will contain X/Y data, but by marking the pen as being in-prox
without an X/Y coordinate, userspace ends up warping the pen to the last-
known X/Y location. As of commit 5b40104edf ("HID: wacom: generic: Reset
events back to zero when pen leaves") this means warping to (0,0).
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As a pen leaves, we need to be sure to reset all events back to zero
so that userspace is able to get the complete pen state when it enters
proximity again.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When a pen is first able to to be sensed by the tablet, we would like
to inform userspace that a tool is nearby so that it can attempt to
perform palm rejection. Unfortunately, we don't know any information
about the tool that is nearby, so the best we can do is send a prox
event for a generic BTN_TOOL_PEN. If the pen later comes closer and
enters proximity, we can determine the actual tool type and send
BTN_TOOL_PEN out of prox if necessary.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The legacy Intuos codepath and tablet behavior (e.g. the 1st-gen Intuos
Pro, Cintiq 27, etc.) would result in a BTN_TOOL_* event not being cleared
to zero until the tool had completely left the sensing range of the
tablet. Before the final "out of prox" packet would be sent, zero or
more "in range" packets could be sent to indicate that a pen was still
detectable but not within a useful distance. These "in range" packets
were used by the driver to keep touch input disabled at greater pen
distances. In addition to keeping the `stylus_in_proximity` flag set,
the driver would leave the current BTN_TOOL_* marked as being in
proximity as well.
The new HID codepath also sets `stylus_in_proximity` based on the "sense"
flag, but does not leave the current BTN_TOOL_* marked as being in prox.
This information is potentially useful to for a future userspace-based
palm rejection, so this patch modifies the driver to continue sending it.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The terminology used to describe the various degrees of pen proximity
within the wacom_wac_pen_report function does not match that used elsewhere
in the generic codepath. Specifically, the names of the variables "prox"
and "range" were inspired by the non-generic codepaths. To make the generic
codepath internally consistent, replace these terms with "range" and "sense"
respectively.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The tool ID information sent in ABS_MISC is expected to be reset to 0
when a tool leaves proximity. Not doing this can cause problems if a
tool is removed and then re-introduced. Kernel event filtering will
prevent the (identical) ABS_MISC event from being sent when the tool
re-enters proxmity. This can cause userspace to not properly set the
tool ID.
Fixes: f85c9dc678 ("HID: wacom: generic: Support tool ID and additional tool types")
Cc: stable # v4.10 <stable@vger.kernel.org>
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The latest generation of pro devices (MobileStudio Pro, 2nd-gen Intuos
Pro, Cintiq Pro) send a serial number of '0' whenever the pen is too far
away for reliable communication. Userspace defines that a serial number
of '0' is invalid, so we need to be careful not to actually forward
this value. Additionally, since EMR ISDv4 devices do not support serial
numbers or tool IDs, we'd like to not send these events if they aren't
necessary.
The existing code achieves these goals by adding a check for a non-zero
serial number within the wacom_wac_pen_report function. The MSC_SERIAL
and ABS_MISC events are only sent if the serial number is non-zero. This
code fails, however when the pen for a pro device leaves proximity. When
the pen leaves prox and the tablet sends a serial of 0, wacom_wac_pen_event
dutifully clears the serial number. When wacom_wac_pen_report is called,
it does not send either the MSC_SERIAL of the exiting tool nor an ABS_MISC
event.
This patch prevents the wacom_wac_pen_event function from clearing an
already-set serial number. This ensures that we have the serial number
handy when exiting proximity, but requires us to manually clear it
afterwards to ensure the driver does not send stale data (e.g. when
switching between AES pens that report a serial nubmer of 0 for the
first few fully in-proximity packets).
Fixes: f85c9dc678 ("HID: wacom: generic: Support tool ID and additional tool types")
Cc: stable # v4.10 <stable@vger.kernel.org>
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The MobileStudio Pro, Cintiq Pro, and 2nd-gen Intuos Pro devices use a
different coordinate system for their touchring and pen twist than prior
devices. Prior devices had zero aligned to the tablet's left and would
increase clockwise. Userspace expects data from the kernel to be in this
old coordinate space, so adjustments are necessary.
While the coordinate system for pen twist is formally defined by the HID
standard, no such definition existed for the touchring at the time these
tablets were introduced. Future tablets are expected to report touchring
data using the same "zero-up clockwise-increasing" coordinate system
defined for twist.
Fixes: 50066a042d ("HID: wacom: generic: Add support for height, tilt, and twist usages")
Fixes: 4922cd26f0 ("HID: wacom: Support 2nd-gen Intuos Pro's Bluetooth classic interface")
Fixes: 60a2218698 ("HID: wacom: generic: add support for touchring")
Cc: stable@vger.kernel.org # 4.10, 4.11
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The wacom driver's IRQ handler for Bluetooth reports from the 2nd-gen
Intuos Pro does not correctly process negative numbers. Values for
tilt and rotation (which can go negative) are instead interpreted as
unsigned and so jump to very large values when the data should be
negative. This commit properly casts the data to ensure we report
negative numbers when necessary.
Fixes: 4922cd2 ("HID: wacom: Support 2nd-gen Intuos Pro's Bluetooth classic interface")
Cc: stable@vger.kernel.org # v4.11
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cintiq 12 has 10 expresskey buttons. The bit shift for the last
two buttons were off by 5.
Fixes: c7f0522 ("HID: wacom: Slim down wacom_intuos_pad processing")
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Tested-by: Matthieu Robin <matthieu@macolu.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The WACOM_HID_WD_TOUCHRINGSTATUS usage is a single bit which tells us
whether the touchring is currently in use or not. Because we need to
reset the axis value to 0 when the finger is removed, we call
'wacom_map_usage' to ensure that the required type/code values are
associated with the usage. The 'wacom_map_usage' also sets up the axis
range and resolution, however, which is not desired in this particular
case.
Although xf86-input-wacom doesn't do really do anything with the ring's
range or resolution, the libinput driver (for Wayland environments)
uses these values to provide proper angle indications to userspace.
Fixes: 60a2218698 ("HID: wacom: generic: add support for touchring")
Cc: stable@vger.kernel.org
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
trivial fix to spelling mistake in hid_warn warning message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Generic battery handling code is spread between the pen and pad codepaths
since battery usages may appear in reports for either. This makes it
difficult to concisely see the logic involved. Since battery data is
not treated like other data (i.e., we report it through the power_supply
subsystem rather than through the input subsystem), it makes reasonable
sense to split the functionality out into its own functions.
This commit has the generic battery handling duplicate the same pattern
that is used by the pen, pad, and touch interfaces. A "mapping" function
is provided to set up the battery, an "event" function is provided to
update the battery data, and a "report" function is provided to notify
the power_supply subsystem after all the data has been read. We look at
the usage itself rather than its collection to determine if one of the
battery functions should handle it. Additionally, we unconditionally
call the "report" function since there is no particularly good way to
know if a report contained a battery usage; 'wacom_notify_battery()'
will filter out any duplicate updates, however.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
At the moment, our driver relies on 'wacom_battery_get_property()' to
determine the most likely battery state (e.g charging, discharging, or
full) based on the information available. It is not always possible
for the function to properly determine this, however. For instance,
whenever an AES pen leaves proximity the battery state becomes
indeterminite. This commit adds the ability to provide it with explict
state information if desired. Whenever explicit state is not required
(the majority of circumstances), WACOM_POWER_SUPPLY_STATUS_AUTO can
be used in its place.
Three uses of explicit battery status are added: two wireless disconnect
paths and the AES case mentioned above.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When support for the HID_DG_BATTERYSTRENGTH usage was added for AES devices,
it appears that the value was read, but never actually forwarded to the
power_supply subystem for userspace's benefit. Let's correct that.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
AES sensors use the value 0 to indicate "not available" rather than
"completely dead". Such values are often sent for dozens of reports
while the pen is being brought into proximity and can cause userspace
to get the wrong impression about the actual battery state.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The power_supply subsystem expects us to provide it with capacity values
measured in percent. In particular, AES devices (HID_DG_BATTERYSTRENGTH)
use the range 0-255, which needs to be rescaled. The MobileStudio Pro
(WACOM_HID_WD_BATTERY_LEVEL) uses the range 0-100, but there's no guarantee
that future devices will share the same range.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The following Smatch complaint was generated in response to commit
2a6cdbd ("HID: wacom: Introduce new 'touch_input' device"):
drivers/hid/wacom_wac.c:1586 wacom_tpc_irq()
error: we previously assumed 'wacom->touch_input' could be null (see line 1577)
The 'touch_input' and 'pen_input' variables point to the 'struct input_dev'
used for relaying touch and pen events to userspace, respectively. If a
device does not have a touch interface or pen interface, the associated
input variable is NULL. The 'wacom_tpc_irq()' function is responsible for
forwarding input reports to a more-specific IRQ handler function. An
unknown report could theoretically be mistaken as e.g. a touch report
on a device which does not have a touch interface. This can be prevented
by only calling the pen/touch functions are called when the pen/touch
pointers are valid.
Fixes: 2a6cdbd ("HID: wacom: Introduce new 'touch_input' device")
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It apears that devices designed around Wacom's G11 chipset (e.g. Lenovo
ThinkPad Yoga 260, Lenovo ThinkPad X1 Yoga, Dell XPS 12 9250, Dell Venue
8 Pro 5855, etc.) suffer from a common issue in their HID descriptors.
The logical maximum is not updated for the "Contact Identifier" usage,
leaving it as just "1" despite these devices being capable of tracking
far more touches.
Commit 60a2218698 began ignoring usages with out-of-range values,
causing problems for devices based on this chipset. Touches after
the first will have an out-of-range Contact Identifier, and ignoring
that usage will cause the kernel to incorrectly slot each finger's
events (along with all the knock-on userspace effects that entails).
This commit checks for these buggy descriptors and updates the maximum
where required. Prior chipsets have used "255" as the maximum (and the
G11, at least, doesn't seem to actually use IDs outside the range of
1..CONTACTMAX) so continue using this value.
Cc: stable@vger.kernel.org
Fixes: 60a2218698 ("HID: wacom: generic: add support for touchring")
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Because HID_DG_TOOLSERIALNUMBER doesn't first cast the value recieved from HID
to an unsigned type, sign-extension rules can cause the value of
wacom_wac->serial[0] to inadvertently wind up with all 32 of its highest bits
set if the highest bit of "value" was set.
This can cause problems for Tablet PC devices which use AES sensors and the
xf86-input-wacom userspace driver. It is not uncommon for AES sensors to send a
serial number of '0' while the pen is entering or leaving proximity. The
xf86-input-wacom driver ignores events with a serial number of '0' since it
cannot match them up to an in-use tool. To ensure the xf86-input-wacom driver
does not ignore the final out-of-proximity event, the kernel does not send
MSC_SERIAL events when the value of wacom_wac->serial[0] is '0'. If the highest
bit of HID_DG_TOOLSERIALNUMBER is set by an in-prox pen which later leaves
proximity and sends a '0' for HID_DG_TOOLSERIALNUMBER, then only the lowest 32
bits of wacom_wac->serial[0] are actually cleared, causing the kernel to send
an MSC_SERIAL event. Since the 'input_event' function takes an 'int' as
argument, only those lowest (now-cleared) 32 bits of wacom_wac->serial[0] are
sent to userspace, causing xf86-input-wacom to ignore the event. If the event
was the final out-of-prox event, then xf86-input-wacom may remain in a state
where it believes the pen is in proximity and refuses to allow other devices
under its control (e.g. the touchscreen) to move the cursor.
It should be noted that EMR devices and devices which use both the
HID_DG_TOOLSERIALNUMBER and WACOM_HID_WD_SERIALHI usages (in that order) would
be immune to this issue. It appears only AES devices are affected.
Fixes: f85c9dc678 ("HID: wacom: generic: Support tool ID and additional tool types")
Cc: stable@vger.kernel.org
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These two functions awkwardly break up the otherwise-contiguous chunk of
related Intuos IRQ functions with a 500 line tangent about the operation
of the EKR. Their presence makes it difficult to read/navigate through the
the Intuos code. Since there is no dependency between these functions, it
is possible to simply move them down somewhat. This commit moves them
to be after the final Intuos IRQ function.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commits d793ff8 and 4082da8 introduced two pad usages which do not
actually send pad input events. To make sure we do not post empty
pad packets, pad_input_event_flag is introduced. Turn on the flag
for real pad input events so we can synchronize them properly.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 3b164a00a9 ("HID: wacom: Cleanup unsupported device_type
for BAMBOO_PT") cleaned up Bamboo devices which our driver falsely
claimed had touch. Bamboo One Medium also does not have touch.
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit f85c9dc ("Support tool ID and additional tool types") introduced mouse
and lens cursor tools to generic codepath, which covers both display (direct)
and opaque tablets (indirect devices). However, mouse and lens cursor tools are
only provided for opaque tablets. This patch ignores mouse and lens cursor tools
if the device is a display tablet.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The features struct for the second gen Intuos Pro uses the wrong constant for
the resolution. This fix is for commit 4922cd2.
Fixes: 4922cd2 ("HID: wacom: Support 2nd-gen Intuos Pro's Bluetooth classic interface")
Signed-off-by: Aaron Armstrong Skomra <skomra@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Wacom Cintiq Pro has a softkey to turn touch on/off. Since it is
a softkey, hardware/firmware still reports touch events no matter
what state the softkey is. We need to ignore touch events when
the key is in off mode.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Wacom Cintiq Pro added a touch key to switch the tablet between
display and opaque mode. This patch informs the change by removing
the old devices and creating new ones with proper properties.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Tested-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch add support to the 3 touch keys on Wacom Cintiq Pro. These touch
keys are in the middle of the other two keys on the top edge of the tablet.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The prox/range bits included in the Bluetooth reports from the Intuos Pro
were being ignored, leading to two issues. Firstly, the pen would never
announce a BTN_TOOL_PEN event with value 0, leaving userspace to believe
the pen was always active. Secondly, the driver would continue to send
events for data while the packet's "prox" bit was clear. This can lead
to sudden incorrect pointer jumps if the pen is slowly moved away from
the tablet surface.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Non-generic devices have numbered_buttons set for both pen and
touch interfaces by default. The actual number of buttons on the
interface is normally manually decided later, which is different
from what those HID generic devices are processed, where number
of buttons are directly retrieved from HID descriptors.
This patch adds the missed HID_GENERIC check and moves the statement
to wacom_setup_pad_input_capabilities since it's not a quirk anymore.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 025bcc1 performed cleanup work on the 'wacom_pl_irq' function, making
it follow the standards used in the rest of the codebase. The change
unintiontionally allowed the function to send input events from reports
that are not marked as being in prox. This can cause problems as the
report values for X, Y, etc. are not guaranteed to be correct. In
particular, occasionally the tablet will send a report with these values
set to zero. If such a report is received it can caus an unexpected jump
in the XY position.
This patch surrounds more of the processing code with a proximity check,
preventing these zeroed reports from overwriting the current state. To
be safe, only the tool type and ABS_MISC events should be reported when
the pen is marked as being out of prox.
Fixes: 025bcc1540 ("HID: wacom: Simplify 'wacom_pl_irq'")
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for the LEDs around the mode switch to the generic code path in
support of the second generation Intuos Pro.
Signed-off-by: Aaron Skomra <aaron.skomra@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
