* Filter out "default" transfer mode values (0x00 - default PIO mode,
0x01 - default PIO mode w/ IORDY disabled) in write handler for obsoleted
/proc/ide/hd?/settings:current_speed setting.
Allowing "default" transfer mode values is a dangerous thing to do as
we don't support programming controller to the "default" transfer mode
and devices often use different values for the default and maximum PIO
mode (i.e. PIO2 default and PIO4 maximum) so the controller will stay
programmed for higher PIO mode while device will use the lower PIO mode.
There is no functionality loss as by using special IOCTLs device can
still be programmed to "default" transfer modes (it is only useful for
debugging/testing purposes anyway).
* Remove no longer needed IDE_HFLAG_ABUSE_SET_DMA_MODE host flag, it was
previously used by few host drivers to program the controller to PIO0
timings for "default" transfer mode == 0x01 (although some host drivers
would program invalid PIO timings instead).
* Cleanup ide_set_xfer_rate() and add BUG_ON().
Suggested-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Filter out invalid transfer mode values (0x02-0x07) in write handler
for obsoleted /proc/ide/hd?/settings:current_speed setting.
While at it:
* Use XFER_UDMA_6 define.
Suggested-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Lets remove dead Virtual DMA support for now so it doesn't clutter
core IDE code (it can be bring back when there is a need for it):
* Remove IDE_HFLAG_VDMA host flag.
* Remove ide_drive_t.vdma flag.
* cs5520.c: remove stale FIXMEs, cs5520_dma_host_set() and cs5520_dma_ops
(also there is no longer a need to set IDE_HFLAG_NO_ATAPI_DMA).
There should be no functional changes caused by this patch.
Cc: TAKADA Yoshihito <takada@mbf.nifty.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Alan Cox has noticed some time ago that hpt34x is broken
(http://lkml.org/lkml/2007/7/3/257):
"No the old driver doesn't even do that. It starts up. It spuriously
adjusts some non writable PCI BAR registers, prints a message about
resources being in use already then exits."
Reported-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove no longer needed ->INB, ->OUTB and ->OUTBSYNC methods.
Then:
* Remove no longer used default_hwif_[mm]iops() and ide_[mm_]outbsync().
* Cleanup SuperIO handling in ns87415.c.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_read_bcount_and_ireason() helper and use it instead of ->INB
in {cdrom_newpc,ide_pc}_intr().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_read_ireason() helper and use instead of ->INB for reading
ATAPI Interrupt Reason register.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_TFLAG_IN_FEATURE taskfile flag for reading Feature
register and handle it in ->tf_read.
* Convert ide_read_error() to use ->tf_read instead of ->INB,
then uninline and export it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert SELECT_DRIVE() to use ->tf_load instead of ->OUTB.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert actual_try_to_identify() to use ->tf_load instead of ->OUTB.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert ide_config_drive_speed() to use ->tf_load instead of ->OUTB.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Write ATA Feature register before ATA Sector Count register as
a preparation to use ->tf_load in ide_config_drive_speed().
This change shouldn't affect anything (just an usual paranoia).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->set_irq method for setting nIEN bit of ATA Device Control
register and use it instead of ide_set_irq().
While at it:
* Use ->set_irq in init_irq() and do_reset1().
* Don't use HWIF() macro in ide_check_pm_state().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove ide_read_altstatus() inline helper.
* Add ->read_altstatus method for reading ATA Alternate Status
register and use it instead of ->INB.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove ide_read_status() inline helper.
* Add ->read_status method for reading ATA Status register
and use it instead of ->INB.
While at it:
* Don't use HWGROUP() macro.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->exec_command method for writing ATA Command register
and use it instead of ->OUTBSYNC.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out simplex handling from ide_pci_dma_base() to
ide_pci_check_simplex().
* Set hwif->dma_base early in ->init_dma method / ide_hwif_setup_dma()
and reset it in ide_init_port() if DMA initialization fails.
* Use ->read_sff_dma_status instead of ->INB in ide_pci_dma_base().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Export sff_dma_ops and then remove ide_setup_dma().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use ->dma_base + offset instead of ->dma_{status,command}
and remove no longer needed ->dma_{status,command}.
While at it:
* Use ATA_DMA_* defines.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use I/O ops directly in ide_dma_host_set(), ide_dma_setup(),
ide_dma_start() and __ide_dma_end().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->read_sff_dma_status method for reading DMA Status register
and use it instead of ->INB.
While at it:
* Use inb() directly in ns87415.c::ns87415_dma_end().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'hw_regs_t **hws' argument to ide_device_add[_all]() and convert
host drivers + ide_legacy_init_one() + ide_setup_pci_device[s]() to use
it instead of calling ide_init_port_hw() directly.
[ However if host has > 1 port we must still set hwif->chipset to hint
consecutive ide_find_port() call that the previous slot is occupied. ]
* Unexport ide_init_port_hw().
v2:
* Use defines instead of hard-coded values in buddha.c, gayle.c and q40ide.c.
(Suggested by Geert Uytterhoeven)
* Better patch description.
v3:
* Fix build problem in ide-cs.c. (Noticed by Stephen Rothwell)
There should be no functional changes caused by this patch.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move ide_pci_setup_ports() call out from do_ide_setup_pci_device()
to ide_setup_pci_device[s]().
* Drop no longer needed idx argument from do_ide_setup_pci_device().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move ide_find_port() call to pmac_ide_setup_device().
While at it:
- fix return value (s/-ENODEV/-ENOENT/)
- add DRV_NAME define and use it to set name field of pmac_port_info
- use ide_find_port_slot() instead of ide_find_port()
- remove superfluous error message (ide_find_port_slot() takes care of it)
- drop IDE interface number from driver banner message (but include bus type)
v2:
* Build fix (thanks to Stephen Rothwell for noticing the issue).
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Pass pmif instead of hwif to pmac_ide_do_{suspend,resume}().
* Store pmif instead of hwif in ->driver_data.
* Use dev_get_drvdata() instead of ->hwif_data to obtain pmif.
v2:
* Build fixes from Stephen Rothwell.
There should be no functional changes caused by this patch.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure that each error condition during the execution of an
HDIO_DRIVE_RESET ioctl is actually reported to the calling process.
Also, unify the exit path of reset_pollfunc() when returning ide_stopped
since the need of ->port_ops->reset_poll() to be treated specially has
vanished (way back, it seems).
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Cc: "Alan Cox" <alan@lxorguk.ukuu.org.uk>
Cc: "Randy Dunlap" <randy.dunlap@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove some code which has been made obsolete and hasn't worked properly
before anyway. Part of the infrastructure may be reintroduced in a
follow up patch to implement a working command aborting facility.
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Cc: "Alan Cox" <alan@lxorguk.ukuu.org.uk>
Cc: "Randy Dunlap" <randy.dunlap@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Currently, the code path executing an HDIO_DRIVE_RESET ioctl is broken
in various ways. Most importantly, it is treated as an out of band
request in an illegal way which may very likely lead to system lock ups.
Use the drive's request queue to avoid this problem (and fix a locking
issue for free along the way).
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Cc: "Alan Cox" <alan@lxorguk.ukuu.org.uk>
Cc: "Randy Dunlap" <randy.dunlap@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch moves hd.c to drivers/block/
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: rmk@arm.linux.org.uk
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since the later move to drivers/block/ will break the link order,
the module_init() has to become a late_initcall().
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: rmk@arm.linux.org.uk
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
After commit 80aa31cb46
(ide: remove CONFIG_BLK_DEV_HD_IDE config option (take 2))
the indirection through BLK_DEV_HD_ONLY is no longer required.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: rmk@arm.linux.org.uk
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is a precaution just to make sure a new pc is clean when allocated.
There should be no functional change introduced by this patch.
[bart: ported it over IDE changes]
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There's no need for this function since it is used only once.
[bart: ported it over IDE changes]
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
As a nice side effect, this minimizes the IRQ handler execution time.
There should be no functionality change resulting from this patch.
[bart: remove extra newlines from ide_cd_do_request()]
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
... by factoring out the rq preparation code into a separate
function called in the request routine. As a nice side effect,
this minimizes the IRQ handler execution time.
There should be no functionality change resulting from this patch.
[bart: s/HWGROUP()/drive->hwif->hwgroup/ and remove extra newline]
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
... by factoring out the rq preparation code into a separate
function called in the request routine. As a nice side effect,
this minimizes the IRQ handler execution time.
There should be no functionality change resulting from this patch.
[bart: s/HWGROUP()/drive->hwif->hwgroup/ and remove extra newlines]
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Do what the compiler does anyway: inline a function that is used only once.
This saves us the overhead of a function call and the function is small enough
to be embedded in the callsite anyways.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Call cdrom_start_packet_command() only from the ->do_request() routine.
As a nice side effect, this improves code readability a bit.
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is done in the request issue path anyway.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move ide_find_port_slot() call closer to ide_device_add().
This is basically a preparation for the future changes.
Cc: Jeremy Higdon <jeremy@sgi.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move ide_find_port_slot() call closer to ide_device_add().
This is basically a preparation for the future changes.
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Try to probe first interface even if ide_hwifs[]'s slot for the second
interface cannot be obtained.
While at it:
- Add DRV_NAME define and use it for request_dma() instead of hwif->name.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Return -ENOENT on ide_find_port() failure.
While at it:
- Cleanup rapide_probe() a bit.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
v2:
On Sunday 15 June 2008, Geert Uytterhoeven wrote:
> As ide-taskfile.c uses scatterlists, it should include <linux/scatterlist.h>.
(v1 broke IDE build on m68k, thanks to Geert for finding the bug)
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide_set_handler() bugs on ->handler == NULL so no need to do it
in set_geometry_intr().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Allow any command requesting DMA data phase for HDIO_DRIVE_TASKFILE ioctl
and remove no longer needed task_dma_ok()
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add DRV_NAME define to ide-h8300.c.
* Fix ide-h8300.c, swarm.c and sgiioc4.c to set .name field in
struct ide_port_info to DRV_NAME, then convert these host drivers
to use ide_find_port_slot() instead of ide_find_port().
* Print message on error in ide_find_port_slot().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert the driver to use struct ide_port_info.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert the driver to use struct ide_port_info.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert the driver to use struct ide_port_info.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert the driver to use ->init_dev method instead of open-coding devices
init in cmd640x_init().
While at it:
- fix printk()-s to use KERN_INFO level instead of the default KERN_ERR
- use DRV_NAME define in printk()-s
- set proper ->pio_mask also for CONFIG_BLK_DEV_CMD640_ENHANCED=n
There should be no functional changes caused by this patch
(except fixing printk()-s levels).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Change ->port_init_devs method to take 'ide_drive_t *' as an argument
instead of 'ide_hwif_t *' and rename it to ->init_dev.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Register secondary interface also when user requested not to probe devices.
While at it:
- remove write-only second_port_toggled variable
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This driver was only used by arch/ppc code and is obsolete
now with the move to common arch/powerpc code.
[bart: port it over IDE tree, remove leftover 'choice' from Kconfig]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert the driver to use struct ide_port_info.
There should be no functional changes caused by this patch.
Acked-by: Maciej W. Rozycki <macro@linux-mips.org>
Tested-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Alan has fixed PCI layer handling of PCI IDE in Compatibility mode so
PCI BAR 0/1 (and/or 2/3) content reported by kernel should never be zero.
Tighten checks on PCI BARs and also fix printk() message while on it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move ide_find_port() and default_hwif_mmiops() calls from icside_setup()
to icside_register_v{5,6}().
* Convert icside_setup() to initialize hw_regs_t instead ide_hwif_t
and icside_register_v{5,6}() to use ide_init_port_hw().
* Rename icside_setup() to icside_setup_ports().
There should be no functional changes caused by this patch.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move ecard_set_drvdata() from icside_probe() to icside_register_v{5,6}(),
then use state->ioc_base instead of hwif->hwif_data in icside_maskproc()
and icside_dma_test_irq().
While at it:
* Add sel field to struct icside_state, then use state->{sel,ioc_base}
instead of ->{select,config}_data in icside_dma_setup().
There should be no functional changes caused by this patch.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert the driver to use struct ide_port_info.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert the driver to use struct ide_port_info - as a nice side-effect
this fixes hwif->channel initialization.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use &auide_hwif directly instead of using hwif->hwif_data.
While at it:
* No need to initialize hwif->{select,config}_data.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'parent' field to hw_regs_t for optional parent device pointer (needed
by macio PMAC IDE controllers) and set hwif->dev in ide_init_port_hw().
* Update au1xxx-ide.c, sgiioc4.c, pmac.c and setup-pci.c accordingly.
v2:
* Update scc_pata.c.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move PIO blacklist to ide-pio-blacklist.c.
While at it:
- fix comment
- fix whitespace damage
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
All ide_pio_cycle_time() users already select CONFIG_IDE_TIMINGS
so move the function from ide-lib.c to ide-timings.c.
While at it:
- convert ide_pio_cycle_time() to use ide_timing_find_mode()
- cleanup ide_pio_cycle_time() a bit
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Also update my Copyrights while at it.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Also fix (disabled) debugging code while at it.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Don't include ide-timing.h in cs5535 and sis5513 host drivers
(they don't need it currently).
* Convert ide-timing.h to ide-timings.c library and add CONFIG_IDE_TIMINGS
config option to be selected by host drivers using the library.
While at it:
- fix ide_timing_find_mode() placement
v2:
* Add missing EXPORT_SYMBOLs. (Stephen Rothwell <sfr@canb.auug.org.au>)
There should be no functional changes caused by this patch.
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Also fix placement of comments in ide_timing_compute() while at it.
There should be no functional changes caused by this patch
(md5sum was verified to be the same before/after the patch).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Check requested xfer mode against xfer modes instead of XFER_* masks
in ide_timing_compute() and cs5535.c::cs5535_set_speed().
* Remove XFER_[MODE,MWDMA,EPIO,PIO] masks.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move struct ide_timing and IDE_TIMING_* defines to <linux/ide.h>
from drivers/ide/ide-timing.h.
While at it:
- use u8/u16 instead of short for struct ide_timing fields
- use enum for IDE_TIMING_*
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove unused XFER_UDMA_SLOW from ide_timing[].
While at it:
- fix re-defining XFER_PIO_5 (no need to define it in ide-timing.h as
it is defined in <linux/ata.h> which is included by <linux/hdreg.h>)
- fix whitespace damage
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove the old BAST IDE driver, as we are now using the platform-pata
support.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This uses the dma safe check for REQ_TYPE_ATA_PC. The dma safe check
is used for only sg requests but it should be used for other non fs
commands.
This uses blk_queue_update_dma_pad to make the intention clear though
ide don't use the blk APIs so it doesn't change anything.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Some REQ_TYPE_ATA_PC commands uses the stack buffers for DMA, which
leads to memory corruption on a non-coherent platform.
With regard to alignment and padding, ide-cd has the the dma safe
check for sg requests and REQ_TYPE_ATA_PC. This adds the stack buffer
check to that check.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver of ITE8212 in pass-through mode (it8212.noraid=1 on cmndline)
attempts to use the field `.dma_host_set' of the struct ide_dma_ops in
`ide_config_drive_speed' which is set to NULL by default.
So give a value to all fields of the struct ide_dma_ops.
Signed-off-by: Dimitri Gorokhovik <dimitri.gorokhovik@free.fr>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There is an outdated version information comment in ide-cs.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (80 commits)
ide-floppy: fix unfortunate function naming
ide-tape: unify idetape_create_read/write_cmd
ide: add ide_pc_intr() helper
ide-{floppy,scsi}: read Status Register before stopping DMA engine
ide-scsi: add more debugging to idescsi_pc_intr()
ide-scsi: use pc->callback
ide-floppy: add more debugging to idefloppy_pc_intr()
ide-tape: always log debug info in idetape_pc_intr() if debugging is enabled
ide-tape: add ide_tape_io_buffers() helper
ide-tape: factor out DSC handling from idetape_pc_intr()
ide-{floppy,tape}: move checking of ->failed_pc to ->callback
ide: add ide_issue_pc() helper
ide: add PC_FLAG_DRQ_INTERRUPT pc flag
ide-scsi: move idescsi_map_sg() call out from idescsi_issue_pc()
ide: add ide_transfer_pc() helper
ide-scsi: set drive->scsi flag for devices handled by the driver
ide-{cd,floppy,tape}: remove checking for drive->scsi
ide: add PC_FLAG_ZIP_DRIVE pc flag
ide-tape: factor out waiting for good ireason from idetape_transfer_pc()
ide-tape: set PC_FLAG_DMA_IN_PROGRESS flag in idetape_transfer_pc()
...
mv idefloppy_transfer_pc1 idefloppy_start_pc_transfer
mv idefloppy_transfer_pc2 idefloppy_transfer_pc
which describes their functionality and disambiguates them. There should be no
functionality change introduced by this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
A straightforward one. There should be no functional change resulting from this
change.
[bart: minor fixups]
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide-tape.c: add 'drive' argument to idetape_update_buffers().
* Add generic ide_pc_intr() helper to ide-atapi.c and then
convert ide-{floppy,tape,scsi} device drivers to use it.
* ide-tape.c: remove no longer needed DBG_PC_INTR.
There should be no functional changes caused by this patch
(unless the debugging is explicitely compiled in).
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Read Status Register before stopping DMA engine to match ide-tape
device driver - it should be safe and shouldn't affect anything.
This is a preparation for adding generic ide_pc_intr() helper.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add more debugging to idefloppy_pc_intr() to match ide-tape's
idetape_pc_intr().
While at it:
* Correct the first debug message.
* Log device name with "DMA finished" message.
This is a preparation for adding generic ide_pc_intr() helper.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add DBG_PC_INTR debug level and use it to always log debug info
in idetape_pc_intr() if debugging is enabled.
While at it:
* Use drive->name instead of tape->name.
* Log device name with "DMA finished" message.
This is a preparation for adding generic ide_pc_intr() helper.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_tape_io_buffers() helper which is a wrapper for
idetape_{in,out}put_buffers() and convert idetape_pc_intr()
to use it.
* Remove no longer used idetape_io_buf typedef.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>---
Factor out DSC handling from idetape_pc_intr() to ide_tape_handle_dsc()
helper as a preparation for adding generic ide_pc_intr() helper.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move checking/resetting of ->failed_pc from ide*_pc_intr() to ->callback
as a preparation for adding generic ide_pc_intr() helper.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>---
Add generic ide_issue_pc() helper to ide-atapi.c and then
convert ide-{floppy,tape,scsi} device drivers to use it.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add PC_FLAG_DRQ_INTERRUPT pc flag, set it in ide*_do_request()
and check for it (instead of checking for IDE*_FLAG_DRQ_INTERRUPT)
in ide*_issue_pc(). This is a preparation for adding generic
ide_issue_pc() helper.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide-atapi.c file for generic ATAPI support together with
CONFIG_IDE_ATAPI config option.
* Add generic ide_transfer_pc() helper to ide-atapi.c and then
convert ide-{floppy,tape,scsi} device drivers to use it.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove checking for drive->scsi which is no longer set by IDE core code
(leave the flag since it will be re-used for generic ATAPI support).
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add PC_FLAG_ZIP_DRIVE pc flag, set it in idefloppy_do_request()
and check for it (instead of checking for IDEFLOPPY_FLAG_ZIP_DRIVE)
in idefloppy_transfer_pc(). This is a preparation for adding
generic ide_transfer_pc() helper.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Factor out waiting for good ireason from idetape_transfer_pc()
to ide_tape_wait_ireason() as a preparation for adding generic
ide_transfer_pc() helper.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Set PC_FLAG_DMA_IN_PROGRESS flag in idetape_transfer_pc() instead of
idetape_issue_pc() to match the other ATAPI device drivers.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Start DMA engine and set PC_FLAG_DMA_IN_PROGRESS flag in
idefloppy_transfer_pc1() instead of idefloppy_issue_pc()
so the Status Register and the Interrupt Reason Register
are checked first.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use PC_FLAG_DMA_OK flag instead of PC_FLAG_DMA_RECOMMENDED one.
* Remove no longer used PC_FLAG_DMA_RECOMMENDED flag.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Merge pc->idefloppy_callback and pc->idetape_callback into pc->callback.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The appropriate functionality of the callback is established through querying
the ATAPI packet command in pc->c[0].
While at it, simplify if (floppy->failed_pc)-branch to be found in the original
idefloppy_request_sense_callback().
Bart:
- keep handling for blk_pc_request() requests unchanged + add FIXME
- add uptodate variable + leave just one idefloppy_end_request() call
- add newline to the debug message
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The appropriate functionality of the callback is established through querying
the ATAPI packet command in pc->c[0].
While at it:
- add uptodate variable + leave just one idetape_end_request() call
- don't use HWGROUP() macro
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
idetape_retry_pc() always returns ide_stopped so make it void.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Log device name instead of driver name in *_pc_intr() and *_transfer_pc*().
While at it:
* Merge two consecutive printk()-s in *_pc_intr() together.
* Replace "floppy"/"tape"/"scsi" references in printk()-s by "device".
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Check IDEFLOPPY_FLAG_ZIP_DRIVE flag in idefloppy_transfer_pc1()
and skip idefloppy_transfer_pc2()-phase if the flag is not set.
* Always use idefloppy_transfer_pc1() in idefloppy_issue_pc()
and remove no longer needed idefloppy_transfer_pc().
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
PC_FLAG_DMA_IN_PROGRESS flag is never set if DMA support is disabled.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide_dma_off() prints info about DMA being disabled.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide_dma_off() prints info about DMA being disabled.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide_do_drive_cmd is called only with ide_preempt action argument. So
we can remove the action argument in ide_do_drive_cmd and ide_action_t
typedef.
This patch also includes two minor cleanups: 1) ide_do_drive_cmd
always succeeds so we don't need the return value; 2) the callers use
blk_rq_init before ide_do_drive_cmd so there is no need to initialize
rq->errors.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove drive->ctl (it is always equal to 0x08 after init time).
While at it:
* Use ATA_DEVCTL_OBS define.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since scc_pata host driver no longer uses IDE PCI layer / ide_dma_setup()
and all other ->mmio users set also IDE_HFLAG_MMIO host flag we can safely
remove ->mmio flag.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move IRQ unmasking out from ->tf_load method to its users.
There should be no functional changes caused by this patch
(SELECT_MASK() is NOP except for hpt366, icside and sgiioc4).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Always call SELECT_MASK(..., 0) in ide_tf_load() (needs to be done
to match ide_set_irq(..., 1)) and then remove IDE_TFLAG_NO_SELECT_MASK
taskfile flag.
This change should only affect hpt366 and icside host drivers since
->maskproc(..., 0) for sgiioc4 is equivalent to ide_set_irq(..., 1).
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix one place in do_probe() which used ->OUTB directly instead
of calling SELECT_DRIVE() (so ->selectproc method is also used).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is a preparation for removal of ->dma_status field from ide_hwif_t.
There should be no functional changes caused by this patch.
Acked-by: Jeremy Higdon <jeremy@sgi.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Just use the new & shiny ide_pad_transfer() helper instead.
Also remove the superfluous check for 'drive->media == ide_disk'
while at it (ide_ata_error() is used only for ide_disk devices).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide_cd_init_rq is not used by ide-cd_ioctl any more. Only
cdrom_queue_request_sense use it. This converts
cdrom_queue_request_sense to use blk_rq_init directly and removes
ide_cd_init_rq.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Borislav Petkov <petkovbb@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide_init_drive_cmd just calls blk_rq_init. This converts the users of
ide_init_drive_cmd to use blk_rq_init directly and removes
ide_init_drive_cmd.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Borislav Petkov <petkovbb@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Now all the users of ide_do_drive_cmd using ide_wait/head_wait are
converted to use blk_execute_rq this removes the ide_wait/head_wait
path in ide_do_drive_cmd.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Borislav Petkov <petkovbb@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This converts ide_cd_queue_pc to use blk_execute_rq, necessitating
changing the ide_cd_queue_pc prototype into a form that doesn't takes
a pointer to request struct. ide_cd_queue_pc works like scsi_execute.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Borislav Petkov <petkovbb@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Call __elv_add_request() with 'plug' == 1 (so the device will be
plugged) and then use __generic_unplug_device() instead of calling
ide_do_request() directly.
v2:
* For blk_pm_resume_request() requests the queue is stopped so we
need to call ->request_fn explicitly.
Thanks to:
- Rafael for reporting/bisecting the bug
- Borislav/Rafael for testing the fix
This is a preparation for converting IDE to use blk_execute_rq().
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Borislav Petkov <petkovbb@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Set REQ_PREEMPT request flag in ide_do_drive_cmd() users
for ide_preempt and ide_head_wait action types.
* Remove setting REQ_PREEMPT from ide_do_drive_cmd().
While at it:
* Set 'where' variable outside ide_lock.
This is a preparation for converting IDE to use blk_execute_rq().
There should be no functional changes caused by this patch.
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Borislav Petkov <petkovbb@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Replace the FIT() macro with the kernel-provided clamp_val() macro.
FIT was always being called with a member of a struct ide_timing,
which are shorts, and constant constraints for the min and max.
Thus we can use clamp_val, rather than clamp_t.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since ide_driveid_update() uses polling to execute the IDENTIFY DEVICE command
but clears nIEN bit in the control register and doesn't mask the IDE interrupt,
the latter does happen and lead to the corresponding message to appear:
ide0: unexpected interrupt, status=0x58, count=1
when e.g. running hdparm with option -X with a non-PCI IDE driver...
Signed-off-by: Mikhail Cherkashin <mcherkashin@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix tRP timing for UDMA mode 4 according to the ATA specification.
Signed-off-by: Mikhail Cherkashin <mcherkhashin@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sparse shows the following warning:
CHECK drivers/ide/legacy/ide-cs.c
drivers/ide/legacy/ide-cs.c:378:6: warning: symbol 'ide_release' was
not declared. Should it be static?
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
CC: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The code in module ide-cs does not conform to the current standard if
setting CONFIG_PCMCIA_DEBUG to "y", and loading the module with the
option "pc_debug=N". When that is fixed, then a warning results that
version is defined but not used. This patch fixes both situations.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
CC: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The driver uses completely bogus rounding formula for calculating period from
the IDECLK frequency which gives one-off period values (e.g. 11 ns with 100 MHz
IDECLK) which in turn can lead to overclocked IDE transfer timings. Actually,
rounding is just wrong in this case, so use a mere division for a safe result.
While at it, also:
- give 'ide_palm_clk' variable a more suitable name;
- get rid of the useless 'ideclkp' variable;
- drop the LISP stype 'p' postfix from the 'clkp' variable's name. :-)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: mcherkashin@ru.mvista.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add __ide_default_irq() inline helper and use it instead of
ide_default_irq() in ide-probe.c and ns87415.c (all host drivers
except IDE PCI ones always setup hwif->irq so it is enough to
check only for I/O bases 0x1f0 and 0x170).
This fixes post-2.6.25 regression since ide_default_irq()
define could shadow ide_default_irq() inline.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Holding ide_lock for ide_release_dma_engine() call is unnecessary
and triggers WARN_ON(irqs_disabled()) in dma_free_coherent().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
class->dev_release is called by device_release() iff dev->release
is not present so ide_port_class_release() is never called and the
last hwif->gendev reference is not dropped.
Fix it by removing ide_port_class_release() and get_device() call
from ide_register_port() (device_create_drvdata() takes a hwif->gendev
reference anyway).
This patch fixes hang on wait_for_completion(&hwif->gendev_rel_comp)
in ide_unregister() reported by Pavel Machek.
Cc: Pavel Machek <pavel@suse.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Now that we support warm-plug mate port will be registered
even if there are no devices attached to it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This reverts commit ac1623625c.
It was premature to remove it now, we will do it post-2.6.26.
Thanks to Russell King for noticing the issue.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove the old BAST IDE driver, as we are now using the platform-pata
support.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Up to now, Kingston compactflash cards (ab)used the Toshiba Manufacturer's ID,
In their new CF cards, they use a new one. Let's the ide subsystem
recognize CF cards with the new id.
Signed-off-by: Christophe Niclaes <cniclaes@develtech.com>
Acked-by: Philippe De Muyter <phdm@macqel.be>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Addition of Transcend 1GB 45x id so that it is properly detected.
[bart: fix typo in ide-cs's ID spotted by Alan Cox]
Signed-off-by: William Peters <w1ll14@gmail.com>
Signed-off-by: Kristoffer Ericson <Kristoffer_e1@hotmail.com>
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>
CC: linux-ide@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Some ATAPI devices take longer than the current max timeout value to
become ready (i.e. TEAC DV-W28ECW takes 6 ms) so increase the timeout
value to 10 ms.
This fixes kernel.org bugzilla bug #10887:
http://bugzilla.kernel.org/show_bug.cgi?id=10887
Reported-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver expected a *virtual* address in the IDE platform device's memory
resource and didn't request the memory region for the register block. Fix this
taking into account the fact that DaVinci SoC devices are fixed-mapped to the
virtual memory early and we can get their virtual addresses using IO_ADDRESS()
macro, not having to call ioremap()...
While at it, also do some cosmetic changes...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
We can't probe all legacy ISA IDE ports by default as the resources may be
occupied by other ISA devices. Add "probe_mask" module parameter and probe
only first two ISA IDE ports by default leaving the decision about probing
the rest to the user (systems with ISA ide2-6 should be very, very rare).
This fixes a regression caused by:
commit 343a3451e2
Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date: Tue Jun 10 20:56:36 2008 +0200
ide-generic: add missing hwif->chipset setup
...
Reported-by: Mikael Pettersson <mikpe@it.uu.se>
Bisected-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
hwif content is already freed after ide_release() call so cache
hwif->io_ports.{data,ctl}_addr in local variables in ide_detach().
This fixes post-2.6.25 regression.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Fix probing by using ide_port_scan() and moving "retry loop"
from ide_config() to idecs_register().
* Don't fail probe if there are no devices attached to a port.
* Remove (now redundant) error message from ide_config().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->cable_detect method and remove no longer needed pmif->cable_80 flag
(there is also no need to mask ->udma_mask now).
This fixes:
- forced ignoring of cable detection (needed for some CF devices & debug)
- cable detection for warm-plug
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add PIO 4 support.
While at it:
* Use a single struct ide_port_info instance for OPTi621 and OPTi621X.
Based on a bugreport from Juergen Kosel & inspired by pata_opti.c code.
Tested-by: Juergen Kosel <juergen.kosel@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use pre-calculated PIO timings in ->set_pio_mode.
* Remove no longer needed compute_clocks(), cmpt_clk(), struct pio_clocks_s,
PIO_* defines and OPTI621_DEBUG define.
There should be no functional changes caused by this patch.
Based on a bugreport from Juergen Kosel & inspired by pata_opti.c code.
Tested-by: Juergen Kosel <juergen.kosel@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Set drive->drive_data to 'pio + XFER_PIO_0' instead of 'pio',
then simplify selecting maximum adress setup timing.
* Remove no longer needed compute_pios() and opti621_port_init_devs().
* Program devices timings separately in ->set_pio_mode.
Based on a bugreport from Juergen Kosel & inspired by pata_opti.c code.
Tested-by: Juergen Kosel <juergen.kosel@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use PCI clock value provided by controller instead of depending on
a default (or user supplied) value.
Based on a bugreport from Juergen Kosel & inspired by pata_opti.c code.
Tested-by: Juergen Kosel <juergen.kosel@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
These controllers don't support DMA.
Based on a bugreport from Juergen Kosel & inspired by pata_opti.c code.
Tested-by: Juergen Kosel <juergen.kosel@gmx.de>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch limits BLK_DEV_HD_ONLY to the ARM platforms offering
IRQ_HARDDISK, fixing the following compile error on others:
<-- snip -->
...
CC drivers/ide/legacy/hd.o
...
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/legacy/hd.c: In function 'hd_times_out':
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/legacy/hd.c:542: error: 'IRQ_HARDDISK' undeclared (first use in this function)
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/legacy/hd.c:542: error: (Each undeclared identifier is reported only once
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/legacy/hd.c:542: error: for each function it appears in.)
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/legacy/hd.c: In function 'do_hd_request':
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/legacy/hd.c:661: error: 'IRQ_HARDDISK' undeclared (first use in this function)
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/legacy/hd.c: In function 'hd_init':
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/ide/legacy/hd.c:765: error: 'IRQ_HARDDISK' undeclared (first use in this function)
make[3]: *** [drivers/ide/legacy/hd.o] Error 1
<-- snip -->
Reported-by: Adrian Bunk <bunk@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Don't fail the probe if there are no devices attached to the controller.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert the driver to use struct ide_port_info - as a nice side-effect
this fixes racy setup of ->io_32bit/unmask settings (after ide_device_add()
call device can be already in use).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
hwif->dev was set too late (after ide_device_add() call)
so hwif->gendev.parent was not initialized properly.
Fix it by setting hw.dev and letting ide_init_port_hw()
do the rest.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide_find_port() now depends on ->chipset being set for occupied ide_hwifs[]
slots so all host drivers have to initialize hwif->chipset properly.
This patch fixes a regression on hosts with > 1 port or with a single port
but no devices attached to it for an affected host drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
hwif->chipset need to be set properly or ide-generic driver will break once
we make a final step in fixing host drivers' dependence on ide_hwifs[].
Problem was catched early thanks to IDE tree exposure in -mm / -next trees
and reported by people listed people (thank you guys!).
Reported-by: "John Keller" <jpk@sgi.com>
Reported-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Reported-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
I forgot to remove the ide_etrax100 chipset type when removing the
ETRAX_IDE driver.
Reported-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There is a race from when a device is created with device_create() and
then the drvdata is set with a call to dev_set_drvdata() in which a
sysfs file could be open, yet the drvdata will be NULL, causing all
sorts of bad things to happen.
This patch fixes the problem by using the new function,
device_create_drvdata().
Cc: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Macintosh IDE driver (macide) doesn't check whether it's actually running
on Mac hardware, causing a crash if it isn't.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Disable Virtual DMA support for now (it causes system hangs).
Thanks to TAKADA Yoshihito for the help with debugging the problem.
Reported-by: TAKADA Yoshihito <takada@mbf.nifty.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Don't ask to enable no longer existing config options
("Use DMA by default when available" and "Special UDMA Feature").
* PIIX host driver doesn't support Victory66 chipset.
* "ide0=cmd640_vlb" -> "cmd640.probe_vlb"
* "ide=doubler" -> "gayle.doubler"
* Amiga IDE doubler support is a feature for gayle host driver
not a separate host driver.
* Remove Andre's mail.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
SELECT_MASK() can now become static.
[bart: remove space between function name and open parenthesis]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Following recent changes to ide_hwif_t update the SWARM IDE driver to use
hw_regs_t to initialize port mapping. Plus minor layout adjustments along
the lines of other drivers.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Patch re-ordering could be harmful:
commit 1fd1890594
Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date: Sat Apr 26 22:25:24 2008 +0200
ide: add IDE_HFLAG_SERIALIZE_DMA host flag
...
is buggy because ->init_dma method / ide_hwif_setup_dma() is called
before IDE_HFLAG_SERIALIZE_DMA host flag is checked.
Fix it by checking IDE_HFLAG_SERIALIZE[_DMA] after DMA initialization.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Thursday 01 May 2008, Jeremy Kerr wrote:
> Hi all,
>
> On QS20 Cell machines, Linus' current git tree explodes on boot:
>
> SiI680: IDE controller (0x1095:0x0680 rev 0x02) at PCI slot
> 0000:00:0a.0
> SiI680: BASE CLOCK == 133
> SiI680: 100% native mode on irq 51
> ide0: MMIO-DMA
> ide1: MMIO-DMA
> Unable to handle kernel paging request for data at address
> 0xa000100081220080
> Faulting instruction address: 0xc000000000024748
> cpu 0x2: Vector: 300 (Data Access) at [c00000001e143420]
> pc: c000000000024748: ._insw_ns+0x10/0x30
> lr: c000000000037fc4: .spiderpci_readsw+0x24/0x6c
> sp: c00000001e1436a0
> msr: 9000000000001032
> dar: a000100081220080
> dsisr: 40000000
> current = 0xc00000003d060000
> paca = 0xc000000000623880
> pid = 1, comm = swapper
> enter ? for help
> [link register ] c000000000037fc4 .spiderpci_readsw+0x24/0x6c
> [c00000001e1436a0] c00000000062ce63 (unreliable)
> [c00000001e143730] c0000000000379d4 .iowa_readsw+0x78/0xa8
> [c00000001e1437c0] c000000000037a98 .iowa_insw+0x94/0xd4
> [c00000001e143850] c00000000022a190 .ata_input_data+0x298/0x2ec
> [c00000001e143910] c00000000022b600 .try_to_identify+0x2c0/0x6d4
> [c00000001e1439d0] c00000000022bb54 .do_probe+0x140/0x35c
> [c00000001e143a80] c00000000022bfbc .ide_probe_port+0x24c/0x670
> [c00000001e143b50] c00000000022d09c .ide_device_add_all+0x2ec/0x690
> [c00000001e143c00] c00000000022d4a4 .ide_device_add+0x64/0x74
> [c00000001e143c90] c00000000022f834 .ide_setup_pci_device+0x58/0x7c
> [c00000001e143d30] c00000000038bdf8
> [c00000001e143e10] c000000000486fb0 .ide_scan_pcibus+0x8c/0x178
> [c00000001e143ea0] c000000000460c00 .kernel_init+0x1c4/0x344
> [c00000001e143f90] c000000000024a1c .kernel_thread+0x4c/0x68
>
> It looks like we're trying to do PIO accesses (which appear to be
> broken, but that's another issue) to this MMIO device. In
> ata_input_data, we see that:
>
> u8 mmio = (hwif->host_flags & IDE_HFLAG_MMIO) ? 1 : 0;
>
> Gives mmio == 0.
>
> (what's the difference between hwif->mmio and ID_HFLAG_MMIO?)
>
> In the siimage driver, hwif->host flags is initially set up correctly
> (host_flags includes IDE_HFLAG_MMIO), but we then *clear* this bit in
> ide_init_port:
>
> hwif->host_flags = d->host_flags;
>
> where d is the struct ide_port_info for this chipset. In my case,
> d->host_flags is 0x0. It looks like this will be the same for all of
> the siimage chipsets.
Don't over-write hwif->host_flags in ide_init_port(), some host drivers
set IDE_HFLAG_MMIO or IDE_HFLAG_NO_IO_32BIT host flag early.
Thanks to Jeremy Kerr for the excellent analysis of the bug.
Reported-by: Jeremy Kerr <jk@ozlabs.org>
Tested-by: Jeremy Kerr <jk@ozlabs.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Ben Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
We don't need init_hwif_ali15x3() on the PowerPC systems either.
Before:
ALI15X3: IDE controller (0x10b9:0x5229 rev 0xc8) at PCI slot 0001:03:1f.0
ALI15X3: 100% native mode on irq 19
ide0: BM-DMA at 0x1120-0x1127
ide1: BM-DMA at 0x1128-0x112f
hda: SONY DVD RW AW-Q170A, ATAPI CD/DVD-ROM drive
hda: UDMA/66 mode selected
ide0: Disabled unable to get IRQ 14.
ide0: failed to initialize IDE interface
ide1: Disabled unable to get IRQ 15.
ide1: failed to initialize IDE interface
After:
ALI15X3: IDE controller (0x10b9:0x5229 rev 0xc8) at PCI slot 0001:03:1f.0
ALI15X3: 100% native mode on irq 19
ide0: BM-DMA at 0x1120-0x1127
ide1: BM-DMA at 0x1128-0x112f
hda: SONY DVD RW AW-Q170A, ATAPI CD/DVD-ROM drive
hda: UDMA/66 mode selected
ide0 at 0x1100-0x1107,0x110a on irq 19
ide1 at 0x1110-0x1117,0x111a on irq 19
hda: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
ide0 works well, though I can't test ide1, it isn't traced out on
the board.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Some change to the IDE layer are causing the siimage driver to crash
at boot with a NULL dereference. This is due to the sil_dma_ops not
containing all the necessary pointers. I suppose it used to just
"override" the defaults while now, it needs to contain everything.
[bart: while at it: sil_dma_ops should be const now (pointed out by Sergei)]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>,
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: Skip I/O merges when disabled
block: add large command support
block: replace sizeof(rq->cmd) with BLK_MAX_CDB
ide: use blk_rq_init() to initialize the request
block: use blk_rq_init() to initialize the request
block: rename and export rq_init()
block: no need to initialize rq->cmd with blk_get_request
block: no need to initialize rq->cmd in prepare_flush_fn hook
block/blk-barrier.c:blk_ordered_cur_seq() mustn't be inline
block/elevator.c:elv_rq_merge_ok() mustn't be inline
block: make queue flags non-atomic
block: add dma alignment and padding support to blk_rq_map_kern
unexport blk_max_pfn
ps3disk: Remove superfluous cast
block: make rq_init() do a full memset()
relay: fix splice problem
Use proc_create()/proc_create_data() to make sure that ->proc_fops and ->data
be setup before gluing PDE to main tree.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Peter Osterlund <petero2@telia.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Neil Brown <neilb@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a preparation for changing rq->cmd from the static array to a
pointer.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This converts ide to use blk_rq_init to initialize the request.
This is a preparation for large command support, which needs to
initialize the request in a proper way (that is, just doing a memset()
will not work).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix 18 errors and several warnings given by checkpatch.pl:
- use of C99 // comments;
- trailing whitespace;
- 'switch' and 'case' not at the same indentation level;
- no space before the open parenthesis of the 'if' and 'switch' statements;
- space between function name and open parenthesis (though I have introduced
such warnins in some places since the code looks prettier with the spaces);
- including <asm/io.h> instead of <linux/io.h>;
- line over 80 characters.
In addition to these changes, also do the following:
- make the arrays in sil_set_pio_mode() 'static', and make the arrays in
sil_set_dma_mode() 'static const';
- change the string of the 'if' statements into the 'switch' statement in
sil_pata_udma_filter();
- drop the needless '==' operators from the 'if' statements where a condition
is a mere bit test;
- remove needless initializer for the 'tmp' variable in init_chipset_siimage();
- beautify groups of the variable initializers and assignment operators;
- add new line after variable definitions;
- remove new line between the comment and the statements it refers to;
- remove needless curly braces and parentheses;
- fix typos, capitalize acronyms, etc. in the comments...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ETRAX_IDE was marked as broken last year with the comment
"it doesn't even compile currently".
Remove it since it won't get fixed in the near future.
On Mon, Apr 14, 2008 at 02:50:19PM +0200, Mikael Starvik wrote:
> You can remove it for now and we will resubmit a new if/when we get around
> to fix it.
[bart: ported it over IDE tree]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Cc: Jesper Nilsson <Jesper.Nilsson@axis.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use 'hwif->dma_base + {4,8}' instead of hwif->dma_prdtable in
{ide,scc}_dma_setup().
* Remove no longer needed ->dma_prdtable field from ide_hwif_t.
While at it:
* Use ATA_DMA_TABLE_OFS define.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use 'hwif->dma_base + {1,3}' instead of hwif->dma_vendor{1,3} in
pdc202xx_new host driver.
* Remove no longer needed ->dma_vendor{1,3} fields from ide_hwif_t.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->dma_host_set and ->dma_start methods (+ __scc_dma_end() helper)
so scc_ide_{in,out}b() can be used directly.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Skip "VLB sync" in ata_{in,out}put_data() if host uses MMIO.
* Use I/O ops directly in ata_vlb_sync() an drop no longer needed
'ide_drive_t *drive' argument.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_pad_transfer() helper (which uses ->{in,out}put_data methods
internally so the transfer is also padded to drive+host requirements)
and use it instead of ide_atapi_{write_zeros,discard_data}().
* Remove no longer needed ide_atapi_{write_zeros,discard_data}().
Cc: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove no longer used ->INW and ->OUTW methods.
While at it:
* scc_pata.c: scc_ide_{out,in}w() is called only in scc_tf_{load,read}()
so inline it there.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->tf_read method so out{b,w}(), in{b,w}() and superio_ide_inb()
can be used directly.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->tf_{load,read} methods so scc_ide_{outb,outw,inb,inw}()
can be used directly.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->tf_{load,read} methods so outb()/inb() and mm_outw()/mm_inw()
can be used directly.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->tf_{load,read} methods so cris_ide_{outb,outw,inb,inw}()
can be used directly.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->tf_load and ->tf_read methods to ide_hwif_t and set the default
methods in default_hwif_transport().
* Use ->tf_{load,read} instead o calling ide_tf_{load,read}() directly.
* Make ide_tf_{load,read}() static.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Factor out debugging code from ide_tf_load() to ide_tf_dump() helper
and update ide_tf_load() users accordingly.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_execute_pkt_cmd() helper for executing PACKET command,
then convert ATAPI device drivers to use it.
As a nice side-effect this fixes ide-{floppy,tape,scsi} w.r.t.
ide_lock taking (ide-cd was OK).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
