Add Runtime PM support to the sh_eth driver.
The clock to the ethernet hardware block will be
enabled as long as the network device is up.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the sh_eth driver to allow passing the mac address
using the platform data structure. This to simplify board
setup code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows the CAN controller driver to define the number of echo
skb's used for the local loopback (echo), as suggested by Kurt Van
Dijck, with the function:
struct net_device *alloc_candev(int sizeof_priv,
unsigned int echo_skb_max);
The CAN drivers have been adapted accordingly. For the ems_usb driver,
as suggested by Sebastian Haas, the number of echo skb's has been
increased to 10, which improves the transmission performance a lot.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function bond_create_proc_entry is currently of type int.
Two versions of this function exist:
The one in the ifdef CONFIG_PROC_FS branch always return 0.
The one in the else branch (which is empty) return nothing.
When CONFIG_PROC_FS is undef, this cause the following warning:
drivers/net/bonding/bond_main.c: In function `bond_create_proc_entry':
drivers/net/bonding/bond_main.c:3393: warning: control reaches end of
non-void function
No caller of this function use the returned value.
So change the returned type from int to void and remove the
useless return 0; .
Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Reported-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mdio module now handles reconfiguration of pause advertising
through ethtool, but not initialisation. Add the necessary
initialisation to tenxpress_phy_init().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mdio45_ethtool_gset_npage() and mdio45_ethtool_gset(), check MDIO
pause frame advertising flags and set the corresponding ethtool flags.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if pause autoneg is off we do not set either pause
advertising flag. If autonegotiation of speed and duplex settings is
enabled, there is no way for the link partner to distinguish this from
our refusing to use pause frames.
We should instead set the advertising flags according to the forced
mode so that the link partner can follow our lead. This is consistent
with the behaviour of other drivers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks to various cleanups and refactorings this is now straightforward:
convert the gianfar driver to dev_pm_ops, plus add ->restore() callback
that will fully reinitialize MAC internal registers and BDs.
Note that I kept legacy suspend/resume callbacks so that this patch
doesn't depend on PowerPC changes (i.e. dev_pm_ops support for OF
platform drivers).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After hibernation we want to just reinitialize BDs, no need to allocate
anything. So, factor out BDs initialization code from
gfar_alloc_skb_resourses().
Also, teach gfar_init_bds() to reuse already allocated RX SKBs, i.e.
just call gfar_init_rxbdp() if a SKB was already allocated and mapped.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to just reinitialize RX BDs after hibernation, no need to
map the skb->data again. So let's factor gfar_init_rxbdp() out of
gfar_new_rxbdp().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For hibernation we want to call gfar_init_mac() without need to
free/allocate_skb_resources sequence, so save the DMA address into a
private struct, and move tbase/rbase initialization to gfar_init_mac().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two new functions implemented: gfar_alloc_skb_resources() and
gfar_init_mac(). We'll use gfar_init_mac() for restoring after
hibernation.
The patch just moves the code around, there should be no functional
changes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
startup_gfar() sets the wrap bit for the last rxbd just after
gfar_new_rxbdp() call, which is issued for all rxbds. And
gfar_new_rxbdp() has the following check already:
if (bdp == priv->rx_bd_base + priv->rx_ring_size - 1)
lstatus |= BD_LFLAG(RXBD_WRAP);
So we don't need to set the bit again.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove dma_free_coherent() from stop_gfar() and gfar_start() calls,
place it into free_skb_resources(). That makes SKB resources management
more understandable, plus free_skb_resources() will be used as a cleanup
routine for gfar_alloc_skb_resources() that will be implemented soon.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're going to split the startup_gfar() into 3 separate functions,
so let's cleanup the code a little bit so that cosmetic changes
won't distract attention from logical ones.
- Remove needless casts (e.g. (struct sk_buff **)kmalloc());
- Turn 'unsigned long vaddr;' into 'void *vaddr', to avoid casting;
- Add new 'struct device *dev' variable as a shorthand for
'&priv->ofdev->dev' that is used all over the place, also rename
'struct net_device *dev' to 'struct net_device *ndev';
- Turn printk(KERN_ERR ...) to pr_err(...), which is shorter;
- Don't return bogus -1 (i.e. -EPERM) when request_irq() fails;
- Turn '&priv->regs->' to just '®s->'.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/cnic.c: In function 'cnic_init_storm_conn_bufs':
drivers/net/cnic.c:1757: error: implicit declaration of function 'csum_ipv6_magic'
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool set settings to pasemi_mac_ethtool.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add iSCSI support for bnx2x devices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Shmulik Ravid - Rabinovitz <shmulikr@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hardware and software structures for bnx2x devices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor ring init. code for subsequent 10G patches. Also add rtnl_lock()
in cnic_uio_open() to prevent race condition with netdev events.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the main CNIC registration, callback, MAC addr. setup functions.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Shmulik Ravid - Rabinovitz <shmulikr@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to initialize hardware blocks used for iSCSI.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Shmulik Ravid - Rabinovitz <shmulikr@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For iSCSI MAC address setup in later patches.
Signed-off-by: Shmulik Ravid - Rabinovitz <shmulikr@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the SPQ (slow-path queue) operations will be used
by the cnic code in later patches.
Signed-off-by: Shmulik Ravid - Rabinovitz <shmulikr@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx_ring->sbq_buf_len now holds the length of the mapped portion of the
buffer rather than the overall length.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver has nothing to do, but this marker prevents the event from
showing up 'not handled'.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove explicit setting of error reporting bits.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need PHY drivers to initialize in a static kernel before
the MAC drivers that use them. So link them in first.
Based upon a report by Felix Radensky.
Signed-off-by: David S. Miller <davem@davemloft.net>
It is somewhat non-sensical to allow selecting wireless
drivers without showing wireless core code options, and
since the wext refactoring this has made it possible to
generate configurations that will not build. Avoid this
and make wireless drivers select the wireless options.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This came in through the patch titled:
libertas: first stab at cfg80211 support
I only noticed it because it breaks compat-wireless :)
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: sujith.manoharan@atheros.com
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows the recently added backplane device IDs that support KR
to fail over to KX during link setup. This is accomplished by the new MAC
link setup function ixgbe_setup_mac_link_smartspeed(). Comments were also
updated to better document the reason for the delays chosen for KX, KX4, BX,
BX4 and KR connections.
Signed-off-by: Don Skidmore <don.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch will add the device ID for the 82599-based Ethernet
Express Module X520-P2 SFI card.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the EMAC V4 implementations support 16K Tx FIFOs. This
patch adds support for this functionality and fixes typos in the
Tx FIFO size error messages.
Signed-off-by: Dave Mitchell <dmitchell@appliedmicro.com>
Acked-by: Prodyut Hazarika <phazarika@appliedmicro.com>
Acked-by: Victor Gallardo <vgallardo@appliedmicro.com>
Acked-by: Loc Ho <lho@appliedmicro.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was accidentally omitted from one of the previous patches for firmware event
handling. The handler needs to the enable firmware irq mask when it's done
processing or it may not get any more events interrupts.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call set_multi API after reset recovery. This was exposed by tripping
tx_timeout.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add wait for NIC fifo and MGMNT fifo to empty before applying reset.
Otherwise broken frames can be processed by management processor and
cause it to hang.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The addresses were being added to the filter properly, but were not
being enabled. This adds enable bit to filter write.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcast/multicast should always be routed to the default (zeroeth) rx
ring. Broadcast frames are already routed correctly. This fixes
routing for multicast frames.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently frames are routed based on their type and MAC address. This
patch adds the port number on which the frame arrived to the routing.
This prevents problems in the case where both interfaces have the same MAC address in
a routing configuration.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix RX queue table size and change from random to default hash values.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
