For Tegra124 and Tegra210, the GPU partition cannot be toggled on and
off via the APBDEV_PMC_PWRGATE_TOGGLE_0 register. For these devices, the
partition is simply powered up and down via an external regulator.
For these devices, there is a separate register for controlling the
signal clamping of the partition and this is described in the PMC SoC
data by the "has_gpu_clamp" variable. Use this variable to determine if
the GPU partition can be controlled via the APBDEV_PMC_PWRGATE_TOGGLE_0
register and ensure that no one can incorrectly try to toggle the GPU
partition via the APBDEV_PMC_PWRGATE_TOGGLE_0 register.
Furthermore, we cannot use the APBDEV_PMC_PWRGATE_STATUS_0 register to
determine if the GPU partition is powered for Tegra124 and Tegra210.
However, if the GPU partition is powered, then the signal clamp for the
GPU partition should be removed and so use bit 0 of the
APBDEV_PMC_GPU_RG_CNTRL_0 register to determine if the clamp has been
removed (bit[0] = 0) and the GPU partition is powered.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The function tegra_powergate_is_powered() verifies that the partition
being queried is valid and so there is no need to check this before
calling tegra_powergate_is_powered() in powergate_show(). So remove this
extra check.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra power partitions are referenced by numerical IDs which are the
same values programmed into the PMC registers for controlling the
partition. For a given device, the valid partition IDs may not be
contiguous and so simply checking that an ID is not greater than the
maximum ID supported may not mean it is valid. Fix this by checking if
the powergate is defined in the list of powergates for the Tegra SoC.
Add a helper function for checking valid powergates and use where we
need to verify if the powergate ID is valid or not.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In tegra_powergate_set() the state of the powergates is read and OR'ed
with the bit for the powergate of interest. This unsigned 32-bit value
is then compared with a boolean value to test if the powergate is
already in the desired state. When turning on a powergate, apart from
the powergate that is represented by bit 0, this test will always
return false and so we may attempt to turn on the powergate when it is
already on.
After OR'ing the bit for the powergate, check if the result is not equal
to zero before comparing with the boolean value. Add a helper function
to return the current state of a powergate and use this in both
tegra_powergate_set() and tegra_powergate_is_powered() where we check
the powergate status.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra powergate and rail IDs are always positive values and so change
the type to be unsigned and remove the tests to see if the ID is less
than zero. Update the Tegra DC powergate type to be an unsigned as well.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The PMC base address pointer is initialised during early boot so that
early platform code may used the PMC public functions. During the probe
of the PMC driver the base address pointer is mapped again and the initial
mapping is freed. This exposes a window where a device accessing the PMC
registers via one of the public functions, could race with the updating
of the pointer and lead to a invalid access. Furthermore, the only
protection between multiple devices attempting to access the PMC registers
is when setting the powergate state to on or off. None of the other public
functions that access the PMC registers are protected.
Use the existing mutex to protect paths that may race with regard to
accessing the PMC registers.
Note that functions tegra_io_rail_prepare()/poll() either return a
negative value on failure or zero on success. Therefore, it is not
necessary to check if the return value is less than zero and so only
test that the return value is not zero to test for failure. This
simplifies the error handling with the mutex locking in place.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
During early initialisation, the PMC registers are mapped and the PMC SoC
data is populated in the PMC data structure. This allows other drivers
access the PMC register space, via the public Tegra PMC APIs, prior to
probing the PMC device.
When the PMC device is probed, the PMC registers are mapped again and if
successful the initial mapping is freed. If the probing of the PMC device
fails after the registers are remapped, then the registers will be
unmapped and hence the pointer to the PMC registers will be invalid. This
could lead to a potential crash, because once the PMC SoC data pointer is
populated, the driver assumes that the PMC register mapping is also valid
and a user calling any of the public Tegra PMC APIs could trigger an
exception because these APIs don't check that the mapping is still valid.
Fix this by updating the mapping and freeing the original mapping only if
probing the PMC device is successful.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra124 does not have an L2 power partition and the L2 cache is part of
the cluster 0 non-CPU (CONC) partition. Remove the L2 as a valid
partition for Tegra124. The TRM also shows that there is no L2 partition
for Tegra124.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The power partitions L2, HEG, CELP and C1NC do not exist on Tegra210 but
were incorrectly documented in the TRM. These will be removed from the
TRM and so also remove their definitions.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The debugfs entry for the PMC device will not be removed if the probe of
the device fails to register the restart handler. This leaves behind the
dangling debugfs entry with no driver backing it. Remove the entry to
avoid this.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Sparse reports the following warning for tegra_pmc_init_tsense_reset():
drivers/soc/tegra/pmc.c:741:6: warning: symbol 'tegra_pmc_init_tsense_reset' was not declared. Should it be static?
This function is only used internally by the PMC driver and so fix this
by making it static.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some members of the tegra_pmc structure are missing from the kernel-doc
comment for this structure. Add the missing members.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons:
- Rockchip rk3368 gains power domain support
- Small updates for the ARM spmi driver
- The Atmel PMC driver saw a larger rework, touching both
arch/arm/mach-at91 and drivers/clk/at91
- All reset controller driver changes alway get merged through
arm-soc, though this time the largest change is the addition
of a MIPS pistachio reset driver
- One bugfix for the NXP (formerly Freescale) i.MX weim bus driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HS4G
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons:
- Rockchip rk3368 gains power domain support
- Small updates for the ARM spmi driver
- The Atmel PMC driver saw a larger rework, touching both
arch/arm/mach-at91 and drivers/clk/at91
- All reset controller driver changes alway get merged through
arm-soc, though this time the largest change is the addition of a
MIPS pistachio reset driver
- One bugfix for the NXP (formerly Freescale) i.MX weim bus driver"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
bus: imx-weim: Take the 'status' property value into account
clk: at91: remove useless includes
clk: at91: pmc: remove useless capacities handling
clk: at91: pmc: drop at91_pmc_base
usb: gadget: atmel: access the PMC using regmap
ARM: at91: remove useless includes and function prototypes
ARM: at91: pm: move idle functions to pm.c
ARM: at91: pm: find and remap the pmc
ARM: at91: pm: simply call at91_pm_init
clk: at91: pmc: move pmc structures to C file
clk: at91: pmc: merge at91_pmc_init in atmel_pmc_probe
clk: at91: remove IRQ handling and use polling
clk: at91: make use of syscon/regmap internally
clk: at91: make use of syscon to share PMC registers in several drivers
hwmon: (scpi) add energy meter support
firmware: arm_scpi: add support for 64-bit sensor values
firmware: arm_scpi: decrease Tx timeout to 20ms
firmware: arm_scpi: fix send_message and sensor_get_value for big-endian
reset: sti: Make reset_control_ops const
reset: zynq: Make reset_control_ops const
...
Newly added support for additional SoCs:
- Axis Artpec-6 SoC family
- Allwinner A83T SoC
- Mediatek MT7623
- NXP i.MX6QP SoC
- ST Microelectronics stm32f469 microcontroller
New features:
- SMP support for Mediatek mt2701
- Big-endian support for NXP i.MX
- DaVinci now uses the new DMA engine dma_slave_map
- OMAP now uses the new DMA engine dma_slave_map
- earlyprintk support for palmchip uart on mach-tango
- delay timer support for orion
Other:
- Exynos PMU driver moved out to drivers/soc/
- Various smaller updates for Renesas, Xilinx, PXA, AT91, OMAP, uniphier
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ynNj
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"Newly added support for additional SoCs:
- Axis Artpec-6 SoC family
- Allwinner A83T SoC
- Mediatek MT7623
- NXP i.MX6QP SoC
- ST Microelectronics stm32f469 microcontroller
New features:
- SMP support for Mediatek mt2701
- Big-endian support for NXP i.MX
- DaVinci now uses the new DMA engine dma_slave_map
- OMAP now uses the new DMA engine dma_slave_map
- earlyprintk support for palmchip uart on mach-tango
- delay timer support for orion
Other:
- Exynos PMU driver moved out to drivers/soc/
- Various smaller updates for Renesas, Xilinx, PXA, AT91, OMAP,
uniphier"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: uniphier: rework SMP code to support new System Bus binding
ARM: uniphier: add missing of_node_put()
ARM: at91: avoid defining CONFIG_* symbols in source code
ARM: DRA7: hwmod: Add data for eDMA tpcc, tptc0, tptc1
ARM: imx: Make reset_control_ops const
ARM: imx: Do L2 errata only if the L2 cache isn't enabled
ARM: imx: select ARM_CPU_SUSPEND only for imx6
dmaengine: pxa_dma: fix the maximum requestor line
ARM: alpine: select the Alpine MSI controller driver
ARM: pxa: add the number of DMA requestor lines
dmaengine: mmp-pdma: add number of requestors
dma: mmp_pdma: Add the #dma-requests DT property documentation
ARM: OMAP2+: Add rtc hwmod configuration for ti81xx
ARM: s3c24xx: Avoid warning for inb/outb
ARM: zynq: Move early printk virtual address to vmalloc area
ARM: DRA7: hwmod: Add custom reset handler for PCIeSS
ARM: SAMSUNG: Remove unused register offset definition
ARM: EXYNOS: Cleanup header files inclusion
drivers: soc: samsung: Enable COMPILE_TEST
MAINTAINERS: Add maintainers entry for drivers/soc/samsung
...
As usual, we queue up a few fixes that don't seem urgent enough to go in
through -rc.
- a number of randconfig warning fixes from Arnd
- various small fixes for OMAP
- one somewhat larger patch to restore the OMAP3 cpuidle
tuning that was lost in a cleanup
- a small regression fix for cns3xxx PCI
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YJmM
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-urgent fixes from Arnd Bergmann:
"As usual, we queue up a few fixes that don't seem urgent enough to go
in through -rc.
- a number of randconfig warning fixes from Arnd
- various small fixes for OMAP
- one somewhat larger patch to restore the OMAP3 cpuidle tuning that
was lost in a cleanup
- a small regression fix for cns3xxx PCI"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
CNS3xxx: Fix PCI cns3xxx_write_config()
MAINTAINERS: unify email addrs for Kevin Hilman
CNS3xxx: remove unused *_VIRT definitions
ARM: OMAP2+: Fix hwmod clock for l4_ls
soc: TI knav_qmss: fix dma_addr_t printing
ARM: prima2: always enable reset controller
ARM: socfpga: hide unused functions
ARM: ux500: fix ureachable iounmap()
ARM: ks8695: fix __initdata annotation
ARM: mvebu: mark mvebu_hwcc_pci_nb as __maybe_unused
ARM: mv78xx0: avoid unused function warning
ARM: orion: only select I2C_BOARDINFO when using I2C
ARM: OMAP2+: Fix out of range register access with syscon_config.max_register
ARM: OMAP3: Add cpuidle parameters table for omap3430
ARM: davinci: make I2C support optional
ARM: davinci: DA8xx+DMx combined kernels need PATCH_PHYS_VIRT
ARM: davinci: avoid unused mityomapl138_pn_info variable
ARM: davinci: limit DT support to DA850
ARM: DRA7: hwmod: Add reset data for PCIe
ARM: DRA7: hwmod: Fix OCP2SCP sysconfig
...
Highlights:
- Restructure Linux PTE on Book3S/64 to Radix format from Paul Mackerras
- Book3s 64 MMU cleanup in preparation for Radix MMU from Aneesh Kumar K.V
- Add POWER9 cputable entry from Michael Neuling
- FPU/Altivec/VSX save/restore optimisations from Cyril Bur
- Add support for new ftrace ABI on ppc64le from Torsten Duwe
Various cleanups & minor fixes from:
- Adam Buchbinder, Andrew Donnellan, Balbir Singh, Christophe Leroy, Cyril
Bur, Luis Henriques, Madhavan Srinivasan, Pan Xinhui, Russell Currey,
Sukadev Bhattiprolu, Suraj Jitindar Singh.
General:
- atomics: Allow architectures to define their own __atomic_op_* helpers from
Boqun Feng
- Implement atomic{, 64}_*_return_* variants and acquire/release/relaxed
variants for (cmp)xchg from Boqun Feng
- Add powernv_defconfig from Jeremy Kerr
- Fix BUG_ON() reporting in real mode from Balbir Singh
- Add xmon command to dump OPAL msglog from Andrew Donnellan
- Add xmon command to dump process/task similar to ps(1) from Douglas Miller
- Clean up memory hotplug failure paths from David Gibson
pci/eeh:
- Redesign SR-IOV on PowerNV to give absolute isolation between VFs from Wei
Yang.
- EEH Support for SRIOV VFs from Wei Yang and Gavin Shan.
- PCI/IOV: Rename and export virtfn_{add, remove} from Wei Yang
- PCI: Add pcibios_bus_add_device() weak function from Wei Yang
- MAINTAINERS: Update EEH details and maintainership from Russell Currey
cxl:
- Support added to the CXL driver for running on both bare-metal and
hypervisor systems, from Christophe Lombard and Frederic Barrat.
- Ignore probes for virtual afu pci devices from Vaibhav Jain
perf:
- Export Power8 generic and cache events to sysfs from Sukadev Bhattiprolu
- hv-24x7: Fix usage with chip events, display change in counter values,
display domain indices in sysfs, eliminate domain suffix in event names,
from Sukadev Bhattiprolu
Freescale:
- Updates from Scott: "Highlights include 8xx optimizations, 32-bit checksum
optimizations, 86xx consolidation, e5500/e6500 cpu hotplug, more fman and
other dt bits, and minor fixes/cleanup."
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qkAt
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"This was delayed a day or two by some build-breakage on old toolchains
which we've now fixed.
There's two PCI commits both acked by Bjorn.
There's one commit to mm/hugepage.c which is (co)authored by Kirill.
Highlights:
- Restructure Linux PTE on Book3S/64 to Radix format from Paul
Mackerras
- Book3s 64 MMU cleanup in preparation for Radix MMU from Aneesh
Kumar K.V
- Add POWER9 cputable entry from Michael Neuling
- FPU/Altivec/VSX save/restore optimisations from Cyril Bur
- Add support for new ftrace ABI on ppc64le from Torsten Duwe
Various cleanups & minor fixes from:
- Adam Buchbinder, Andrew Donnellan, Balbir Singh, Christophe Leroy,
Cyril Bur, Luis Henriques, Madhavan Srinivasan, Pan Xinhui, Russell
Currey, Sukadev Bhattiprolu, Suraj Jitindar Singh.
General:
- atomics: Allow architectures to define their own __atomic_op_*
helpers from Boqun Feng
- Implement atomic{, 64}_*_return_* variants and acquire/release/
relaxed variants for (cmp)xchg from Boqun Feng
- Add powernv_defconfig from Jeremy Kerr
- Fix BUG_ON() reporting in real mode from Balbir Singh
- Add xmon command to dump OPAL msglog from Andrew Donnellan
- Add xmon command to dump process/task similar to ps(1) from Douglas
Miller
- Clean up memory hotplug failure paths from David Gibson
pci/eeh:
- Redesign SR-IOV on PowerNV to give absolute isolation between VFs
from Wei Yang.
- EEH Support for SRIOV VFs from Wei Yang and Gavin Shan.
- PCI/IOV: Rename and export virtfn_{add, remove} from Wei Yang
- PCI: Add pcibios_bus_add_device() weak function from Wei Yang
- MAINTAINERS: Update EEH details and maintainership from Russell
Currey
cxl:
- Support added to the CXL driver for running on both bare-metal and
hypervisor systems, from Christophe Lombard and Frederic Barrat.
- Ignore probes for virtual afu pci devices from Vaibhav Jain
perf:
- Export Power8 generic and cache events to sysfs from Sukadev
Bhattiprolu
- hv-24x7: Fix usage with chip events, display change in counter
values, display domain indices in sysfs, eliminate domain suffix in
event names, from Sukadev Bhattiprolu
Freescale:
- Updates from Scott: "Highlights include 8xx optimizations, 32-bit
checksum optimizations, 86xx consolidation, e5500/e6500 cpu
hotplug, more fman and other dt bits, and minor fixes/cleanup"
* tag 'powerpc-4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (179 commits)
powerpc: Fix unrecoverable SLB miss during restore_math()
powerpc/8xx: Fix do_mtspr_cpu6() build on older compilers
powerpc/rcpm: Fix build break when SMP=n
powerpc/book3e-64: Use hardcoded mttmr opcode
powerpc/fsl/dts: Add "jedec,spi-nor" flash compatible
powerpc/T104xRDB: add tdm riser card node to device tree
powerpc32: PAGE_EXEC required for inittext
powerpc/mpc85xx: Add pcsphy nodes to FManV3 device tree
powerpc/mpc85xx: Add MDIO bus muxing support to the board device tree(s)
powerpc/86xx: Introduce and use common dtsi
powerpc/86xx: Update device tree
powerpc/86xx: Move dts files to fsl directory
powerpc/86xx: Switch to kconfig fragments approach
powerpc/86xx: Update defconfigs
powerpc/86xx: Consolidate common platform code
powerpc32: Remove one insn in mulhdu
powerpc32: small optimisation in flush_icache_range()
powerpc: Simplify test in __dma_sync()
powerpc32: move xxxxx_dcache_range() functions inline
powerpc32: Remove clear_pages() and define clear_page() inline
...
1. Split out Exynos PMU driver implementation from arm/mach-exynos
to the drivers/soc/samsung which will allow re-use of it on ARM64.
2. Use generic DT cpufreq driver on Exynos542x/5800.
3. Minor cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/LNl
-----END PGP SIGNATURE-----
Merge tag 'samsung-soc-4.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/soc
Samsung Exynos (and older platforms) improvements for v4.6:
1. Split out Exynos PMU driver implementation from arm/mach-exynos
to the drivers/soc/samsung which will allow re-use of it on ARM64.
2. Use generic DT cpufreq driver on Exynos542x/5800.
3. Minor cleanups.
* tag 'samsung-soc-4.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: s3c24xx: Avoid warning for inb/outb
ARM: SAMSUNG: Remove unused register offset definition
ARM: EXYNOS: Cleanup header files inclusion
drivers: soc: samsung: Enable COMPILE_TEST
MAINTAINERS: Add maintainers entry for drivers/soc/samsung
drivers: soc: Add support for Exynos PMU driver
ARM: EXYNOS: Split up exynos5420 SoC specific PMU data
ARM: EXYNOS: Split up exynos5250 SoC specific PMU data
ARM: EXYNOS: Split up exynos4 SoC specific PMU data
ARM: EXYNOS: Split up exynos3250 SoC specific PMU data
ARM: EXYNOS: Move pmu specific headers under "linux/soc/samsung"
ARM: EXYNOS: Correct header comment in Kconfig file
ARM: EXYNOS: Use generic cpufreq driver for Exynos5422/5800
ARM: EXYNOS: Use generic cpufreq driver for Exynos5420
ARM: s3c64xx: use "depends on" instead of "if" after prompt
ARM: plat-samsung: use to_platform_device()
ARM: EXYNOS: Code cleanup in map.h
ARM: EXYNOS: Remove unused static mapping of CMU for exynos5
Signed-off-by: Olof Johansson <olof@lixom.net>
cpm_muram_alloc_common is called twice and both the times
spin_lock_irqsave is held.
Using GFP_KERNEL can sleep in spin_lock_irqsave context and cause
deadlock
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: Scott Wood <oss@buserror.net>
as cpm_muram_alloc_common is used only in this file,
making it static
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: Scott Wood <oss@buserror.net>
127 is the theoretical up boundary of QEIC number,
in fact there only be 44 qe_ic_info now.
add check to overflow for qe_ic_info
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Some minor fixes for the RSB and SRAM controller drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5Ffk
-----END PGP SIGNATURE-----
Merge tag 'sunxi-drivers-for-4.6' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/drivers
Merge "Allwinner drivers changes for 4.6" from Maxime Ripard:
Some minor fixes for the RSB and SRAM controller drivers
* tag 'sunxi-drivers-for-4.6' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
drivers: soc: sunxi: Fix mask generation for SRAM mapping
drivers: sunxi-rsb: fix error output type
The knav_qmss driver is currently broken when CONFIG_LPAE is
set, which is a bit surprising because I'd expect that any serious
users of this platforms would have more than 2GB of RAM and require
LPAE.
The compiler clearly warns about an incorrect use of dma_addr_t
in the debug kernel messages:
ti/knav_qmss_queue.c: In function 'knav_queue_setup_region':
ti/knav_qmss_queue.c:1025:117: warning: format '%x' expects argument of type 'unsigned int', but argument 9 has type 'dma_addr_t {aka long long unsigned int}' [-Wformat=]
ti/knav_qmss_queue.c:1025:117: warning: format '%x' expects argument of type 'unsigned int', but argument 10 has type 'dma_addr_t {aka long long unsigned int}' [-Wformat=]
ti/knav_qmss_queue.c: In function 'knav_queue_setup_link_ram':
ti/knav_qmss_queue.c:1175:118: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'dma_addr_t {aka long long unsigned int}' [-Wformat=]
This patch changes all the debugging output to use the correct
%pad format string that works with both 32-bit and 64-bit dma_addr_t.
As the variable naming is somewhat confusing here, I also change
all *_phys names to *_dma when they refer to bus addresses that
are used for DMA rather than a physical memory address as seen from
the CPU. This is particularly important on keystone, because the
two things are not the same there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Get some build coverage of Exynos PMU driver. It depends on
asm/cputype.h so its compilation is limited to ARM architectures.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
This patch moves Exynos PMU driver implementation from "arm/mach-exynos"
to "drivers/soc/samsung". This driver is mainly used for setting misc
bits of register from PMU IP of Exynos SoC which will be required to
configure before Suspend/Resume. Currently all these settings are done
in "arch/arm/mach-exynos/pmu.c" but moving ahead for ARM64 based SoC
support, there is a need of this PMU driver in driver/* folder.
This driver uses existing DT binding information and there should
be no functionality change in the supported platforms.
Signed-off-by: Amit Daniel Kachhap <amitdanielk@gmail.com>
[tested on Peach-Pi (Exynos5880)]
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[for testing on Trats2 (Exynos4412) and Odroid XU3 (Exynos5422)]
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[k.kozlowski: Rebased, add necessary infrastructure for building and
selecting drivers/soc because original patchset was on top of movement
SROMc to drivers/soc]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
If we fail to probe the driver, we should not directly break
from the for_each_available_child_of_node since it calls of_node_get
while iterating. This patch add of_node_put to fix the unbalanced
call pair.
Fixes: 7c696693a4 ("soc: rockchip: power-domain: Add power domain driver")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
With CONFIG_PM enabled do not call genpd->power_on manually as this
will cause the regulators being turned on once in SCPSYS probe and
then again when the genpd core turns on the domains. Instead, call
genpd->power_on only with CONFIG_PM disabled and tell the genpd core
that the domains are disabled when registered.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
GENMASK is inclusive on both ends, therefor one has to be
subtracted from the width.
Also fixes the mask for debug output.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
SCPSYS can't be built as module. Use builtin_platform_driver instead.
For this probe must not be __init and the data accessed can't be
__initconst. Remove this macros. To make the impact as small as possible,
fold scp_domain_data into scp_domain via a pointer.
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Reported-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Tested-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Since STAUPD interrupts aren't handled on mt8173, disable watchdog timeout
monitor of STAUPD to avoid WDT_INT triggered by STAUPD.
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Sometimes PMIC is too busy to send data in time to cause pmic wrap timeout,
because pmic wrap is waiting for FSM_VLDCLR after finishing WACS2_CMD. It
just return error when issue happened, so the state machine will stay on
FSM_VLDCLR state when data send back later by PMIC and timeout again in next
time because pmic wrap waiting for FSM_IDLE state at the beginning of the
read/write function.
Clear the vldclr when timeout if state machine stay on FSM_VLDCLR.
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Tested-by: Ricky Liang <jcliang@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver is modified to support RK3368 SoC.
Signed-off-by: zhangqing <zhangqing@rock-chips.com>
Reviewed-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Here's a single-SoC topic branch that we've staged separately. Mainly
because it was hard to sort the branch contents in a way that fit our
existing branches due to some refactorings.
The code has been in -next for quite a while, but we staged it in arm-soc
a bit late, which is why we've kept it separate from the other updates
and are sending it separately here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=LG3u
-----END PGP SIGNATURE-----
Merge tag 'armsoc-tegra' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC support for Tegra platforms from Olof Johansson:
"Here's a single-SoC topic branch that we've staged separately. Mainly
because it was hard to sort the branch contents in a way that fit our
existing branches due to some refactorings.
The code has been in -next for quite a while, but we staged it in
arm-soc a bit late, which is why we've kept it separate from the other
updates and are sending it separately here"
* tag 'armsoc-tegra' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: tegra: Add NVIDIA Jetson TX1 Developer Kit support
arm64: tegra: Add NVIDIA P2597 I/O board support
arm64: tegra: Add NVIDIA Jetson TX1 support
arm64: tegra: Add NVIDIA P2571 board support
arm64: tegra: Add NVIDIA P2371 board support
arm64: tegra: Add NVIDIA P2595 I/O board support
arm64: tegra: Add NVIDIA P2530 main board support
arm64: tegra: Add Tegra210 support
arm64: tegra: Add NVIDIA Tegra132 Norrin support
arm64: tegra: Add Tegra132 support
ARM: tegra: select USB_ULPI from EHCI rather than platform
ARM: tegra: Ensure entire dcache is flushed on entering LP0/1
amba: Hide TEGRA_AHB symbol
soc/tegra: Add Tegra210 support
soc/tegra: Provide per-SoC Kconfig symbols
A few fixes for fallout that we didn't catch in time in -next, or smaller
warning fixes that have been discovered since.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PRjJ
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A few fixes for fallout that we didn't catch in time in -next, or
smaller warning fixes that have been discovered since"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
soc: qcom/spm: shut up uninitialized variable warning
ARM: realview: fix device tree build
ARM: debug-ll: fix BCM63xx entry for multiplatform
ARM: dts: armadillo800eva Correct extal1 frequency to 24 MHz
gcc warns about the 'found' variable possibly being used uninitialized:
drivers/soc/qcom/spm.c: In function 'spm_dev_probe':
drivers/soc/qcom/spm.c:305:5: error: 'found' may be used uninitialized in this function [-Werror=maybe-uninitialized]
However, the code is correct because we know that there is
always at least one online CPU. This initializes the 'found'
variable to zero before the loop so the compiler knows
it does not have to warn about it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge third patch-bomb from Andrew Morton:
"I'm pretty much done for -rc1 now:
- the rest of MM, basically
- lib/ updates
- checkpatch, epoll, hfs, fatfs, ptrace, coredump, exit
- cpu_mask simplifications
- kexec, rapidio, MAINTAINERS etc, etc.
- more dma-mapping cleanups/simplifications from hch"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (109 commits)
MAINTAINERS: add/fix git URLs for various subsystems
mm: memcontrol: add "sock" to cgroup2 memory.stat
mm: memcontrol: basic memory statistics in cgroup2 memory controller
mm: memcontrol: do not uncharge old page in page cache replacement
Documentation: cgroup: add memory.swap.{current,max} description
mm: free swap cache aggressively if memcg swap is full
mm: vmscan: do not scan anon pages if memcg swap limit is hit
swap.h: move memcg related stuff to the end of the file
mm: memcontrol: replace mem_cgroup_lruvec_online with mem_cgroup_online
mm: vmscan: pass memcg to get_scan_count()
mm: memcontrol: charge swap to cgroup2
mm: memcontrol: clean up alloc, online, offline, free functions
mm: memcontrol: flatten struct cg_proto
mm: memcontrol: rein in the CONFIG space madness
net: drop tcp_memcontrol.c
mm: memcontrol: introduce CONFIG_MEMCG_LEGACY_KMEM
mm: memcontrol: allow to disable kmem accounting for cgroup2
mm: memcontrol: account "kmem" consumers in cgroup2 memory controller
mm: memcontrol: move kmem accounting code to CONFIG_MEMCG
mm: memcontrol: separate kmem code from legacy tcp accounting code
...
Driver updates for ARM SoCs. Some for SoC-family code under drivers/soc,
but also some other driver updates that don't belong anywhere else. We also
bring in the drivers/reset code through arm-soc.
Some of the larger updates:
- Qualcomm support for SMEM, SMSM, SMP2P. All used to communicate with other
parts of the chip/board on these platforms, all proprietary protocols that
don't fit into other subsystems and live in drivers/soc for now.
- System bus driver for UniPhier
- Driver for the TI Wakeup M3 IPC device
- Power management for Raspberry PI
+ Again a bunch of other smaller updates and patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=khZ5
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs. Some for SoC-family code under
drivers/soc, but also some other driver updates that don't belong
anywhere else. We also bring in the drivers/reset code through
arm-soc.
Some of the larger updates:
- Qualcomm support for SMEM, SMSM, SMP2P. All used to communicate
with other parts of the chip/board on these platforms, all
proprietary protocols that don't fit into other subsystems and live
in drivers/soc for now.
- System bus driver for UniPhier
- Driver for the TI Wakeup M3 IPC device
- Power management for Raspberry PI
+ Again a bunch of other smaller updates and patches"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
bus: uniphier: allow only built-in driver
ARM: bcm2835: clarify RASPBERRYPI_FIRMWARE dependency
MAINTAINERS: Drop Kumar Gala from QCOM
bus: uniphier-system-bus: add UniPhier System Bus driver
ARM: bcm2835: add rpi power domain driver
dt-bindings: add rpi power domain driver bindings
ARM: bcm2835: Define two new packets from the latest firmware.
drivers/soc: make mediatek/mtk-scpsys.c explicitly non-modular
soc: mediatek: SCPSYS: Add regulator support
MAINTAINERS: Change QCOM entries
soc: qcom: smd-rpm: Add existing platform support
memory/tegra: Add number of TLB lines for Tegra124
reset: hi6220: fix modular build
soc: qcom: Introduce WCNSS_CTRL SMD client
ARM: qcom: select ARM_CPU_SUSPEND for power management
MAINTAINERS: Add rules for Qualcomm dts files
soc: qcom: enable smsm/smp2p modular build
serial: msm_serial: Make config tristate
soc: qcom: smp2p: Qualcomm Shared Memory Point to Point
soc: qcom: smsm: Add driver for Qualcomm SMSM
...
This branch is the culmination of 5 years of effort to bring the ARMv6
and ARMv7 platforms together such that they can all be enabled and
boot the same kernel. It has been a tremendous amount of cleanup and
refactoring by a huge number of people, and creation of several new
(and major) subsystems to better abstract out all the platform details
in an appropriate manner.
The bulk of this branch is a large patchset from Arnd that brings several
of the more minor and older platforms we have closer to multiplatform
support. Among these are MMP, S3C64xx, Orion5x, mv78xx0 and realview
Much of this is moving around header files from old mach directories,
but there are also some cleanup patches of debug_ll (lowlevel debug
per-platform options) and other parts.
Linus Walleij also has some patchs to clean up the older ARM Realview
platforms by finally introducing DT support, and Rob Herring has some
for ARM Versatile which is now DT-only. Both of these platforms are
now multiplatform.
Finally, a couple of patches from Russell for Dove PMU, and a fix from
Valentin Rothberg for Exynos ADC, which were rebased on top of the
series to avoid conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z1AW
-----END PGP SIGNATURE-----
Merge tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform code updates from Arnd Bergmann:
"This branch is the culmination of 5 years of effort to bring the ARMv6
and ARMv7 platforms together such that they can all be enabled and
boot the same kernel. It has been a tremendous amount of cleanup and
refactoring by a huge number of people, and creation of several new
(and major) subsystems to better abstract out all the platform details
in an appropriate manner.
The bulk of this branch is a large patchset from Arnd that brings
several of the more minor and older platforms we have closer to
multiplatform support. Among these are MMP, S3C64xx, Orion5x, mv78xx0
and realview Much of this is moving around header files from old mach
directories, but there are also some cleanup patches of debug_ll
(lowlevel debug per-platform options) and other parts.
Linus Walleij also has some patchs to clean up the older ARM Realview
platforms by finally introducing DT support, and Rob Herring has some
for ARM Versatile which is now DT-only. Both of these platforms are
now multiplatform.
Finally, a couple of patches from Russell for Dove PMU, and a fix from
Valentin Rothberg for Exynos ADC, which were rebased on top of the
series to avoid conflicts"
* tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (75 commits)
ARM: realview: don't select SMP_ON_UP for UP builds
ARM: s3c: simplify s3c_irqwake_{e,}intallow definition
ARM: s3c64xx: fix pm-debug compilation
iio: exynos-adc: fix irqf_oneshot.cocci warnings
ARM: realview: build realview-dt SMP support only when used
ARM: realview: select apropriate targets
ARM: realview: clean up header files
ARM: realview: make all header files local
ARM: no longer make CPU targets visible separately
ARM: integrator: use explicit core module options
ARM: realview: enable multiplatform
ARM: make default platform work for NOMMU
ARM: debug-ll: move DEBUG_LL_UART_EFM32 to correct Kconfig location
ARM: defconfig: use correct debug_ll settings
ARM: versatile: convert to multi-platform
ARM: versatile: merge mach code into a single file
ARM: versatile: switch to DT only booting and remove legacy code
ARM: versatile: add DT based PCI detection
ARM: pxa: mark ezx structures as __maybe_unused
ARM: pxa: mark raumfeld init functions as __maybe_unused
...
Now that we have a generic library function for this, replace the
open-coded instance.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Cc: <zajec5@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Ground work for the new Power9 MMU from Aneesh Kumar K.V
- Optimise FP/VMX/VSX context switching from Anton Blanchard
- Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica Gupta,
Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling, Andrew Donnellan
- Allow wrapper to work on non-english system from Laurent Vivier
- Add rN aliases to the pt_regs_offset table from Rashmica Gupta
- Fix module autoload for rackmeter & axonram drivers from Luis de Bethencourt
- Include KVM guest test in all interrupt vectors from Paul Mackerras
- Fix DSCR inheritance over fork() from Anton Blanchard
- Make value-returning atomics & {cmp}xchg* & their atomic_ versions fully ordered from Boqun Feng
- Print MSR TM bits in oops messages from Michael Neuling
- Add TM signal return & invalid stack selftests from Michael Neuling
- Limit EPOW reset event warnings from Vipin K Parashar
- Remove the Cell QPACE code from Rashmica Gupta
- Append linux_banner to exception information in xmon from Rashmica Gupta
- Add selftest to check if VSRs are corrupted from Rashmica Gupta
- Remove broken GregorianDay() from Daniel Axtens
- Import Anton's context_switch2 benchmark into selftests from Michael Ellerman
- Add selftest script to test HMI functionality from Daniel Axtens
- Remove obsolete OPAL v2 support from Stewart Smith
- Make enter_rtas() private from Michael Ellerman
- PPR exception cleanups from Michael Ellerman
- Add page soft dirty tracking from Laurent Dufour
- Add support for Nvlink NPUs from Alistair Popple
- Add support for kexec on 476fpe from Alistair Popple
- Enable kernel CPU dlpar from sysfs from Nathan Fontenot
- Copy only required pieces of the mm_context_t to the paca from Michael Neuling
- Add a kmsg_dumper that flushes OPAL console output on panic from Russell Currey
- Implement save_stack_trace_regs() to enable kprobe stack tracing from Steven Rostedt
- Add HWCAP bits for Power9 from Michael Ellerman
- Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V
- Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins
- scripts/recordmcount.pl: support data in text section on powerpc from Ulrich Weigand
- Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand
- cxl: Fix possible idr warning when contexts are released from Vaibhav Jain
- cxl: use correct operator when writing pcie config space values from Andrew Donnellan
- cxl: Fix DSI misses when the context owning task exits from Vaibhav Jain
- cxl: fix build for GCC 4.6.x from Brian Norris
- cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris
- cxl: Enable PCI device ID for future IBM CXL adapter from Uma Krishnan
- Freescale updates from Scott: Highlights include moving QE code out of
arch/powerpc (to be shared with arm), device tree updates, and minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R5bX
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Core:
- Ground work for the new Power9 MMU from Aneesh Kumar K.V
- Optimise FP/VMX/VSX context switching from Anton Blanchard
Misc:
- Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica
Gupta, Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling,
Andrew Donnellan
- Allow wrapper to work on non-english system from Laurent Vivier
- Add rN aliases to the pt_regs_offset table from Rashmica Gupta
- Fix module autoload for rackmeter & axonram drivers from Luis de
Bethencourt
- Include KVM guest test in all interrupt vectors from Paul Mackerras
- Fix DSCR inheritance over fork() from Anton Blanchard
- Make value-returning atomics & {cmp}xchg* & their atomic_ versions
fully ordered from Boqun Feng
- Print MSR TM bits in oops messages from Michael Neuling
- Add TM signal return & invalid stack selftests from Michael Neuling
- Limit EPOW reset event warnings from Vipin K Parashar
- Remove the Cell QPACE code from Rashmica Gupta
- Append linux_banner to exception information in xmon from Rashmica
Gupta
- Add selftest to check if VSRs are corrupted from Rashmica Gupta
- Remove broken GregorianDay() from Daniel Axtens
- Import Anton's context_switch2 benchmark into selftests from
Michael Ellerman
- Add selftest script to test HMI functionality from Daniel Axtens
- Remove obsolete OPAL v2 support from Stewart Smith
- Make enter_rtas() private from Michael Ellerman
- PPR exception cleanups from Michael Ellerman
- Add page soft dirty tracking from Laurent Dufour
- Add support for Nvlink NPUs from Alistair Popple
- Add support for kexec on 476fpe from Alistair Popple
- Enable kernel CPU dlpar from sysfs from Nathan Fontenot
- Copy only required pieces of the mm_context_t to the paca from
Michael Neuling
- Add a kmsg_dumper that flushes OPAL console output on panic from
Russell Currey
- Implement save_stack_trace_regs() to enable kprobe stack tracing
from Steven Rostedt
- Add HWCAP bits for Power9 from Michael Ellerman
- Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V
- Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins
- scripts/recordmcount.pl: support data in text section on powerpc
from Ulrich Weigand
- Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand
cxl:
- cxl: Fix possible idr warning when contexts are released from
Vaibhav Jain
- cxl: use correct operator when writing pcie config space values
from Andrew Donnellan
- cxl: Fix DSI misses when the context owning task exits from Vaibhav
Jain
- cxl: fix build for GCC 4.6.x from Brian Norris
- cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris
- cxl: Enable PCI device ID for future IBM CXL adapter from Uma
Krishnan
Freescale:
- Freescale updates from Scott: Highlights include moving QE code out
of arch/powerpc (to be shared with arm), device tree updates, and
minor fixes"
* tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (149 commits)
powerpc/module: Handle R_PPC64_ENTRY relocations
scripts/recordmcount.pl: support data in text section on powerpc
powerpc/powernv: Fix OPAL_CONSOLE_FLUSH prototype and usages
powerpc/mm: fix _PAGE_SWP_SOFT_DIRTY breaking swapoff
powerpc/mm: Fix _PAGE_PTE breaking swapoff
cxl: Enable PCI device ID for future IBM CXL adapter
cxl: use -Werror only with CONFIG_PPC_WERROR
cxl: fix build for GCC 4.6.x
powerpc: Add HWCAP bits for Power9
powerpc/powernv: Reserve PE#0 on NPU
powerpc/powernv: Change NPU PE# assignment
powerpc/powernv: Fix update of NVLink DMA mask
powerpc/powernv: Remove misleading comment in pci.c
powerpc: Implement save_stack_trace_regs() to enable kprobe stack tracing
powerpc: Fix build break due to paca mm_context_t changes
cxl: Fix DSI misses when the context owning task exits
MAINTAINERS: Update Scott Wood's e-mail address
powerpc/powernv: Fix minor off-by-one error in opal_mce_check_early_recovery()
powerpc: Fix style of self-test config prompts
powerpc/powernv: Only delay opal_rtc_read() retry when necessary
...
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
floppy: make local variable non-static
exynos: fixes an incorrect header guard
dt-bindings: fixes some incorrect header guards
cpufreq-dt: correct dead link in documentation
cpufreq: ARM big LITTLE: correct dead link in documentation
treewide: Fix typos in printk
Documentation: filesystem: Fix typo in fs/eventfd.c
fs/super.c: use && instead of & for warn_on condition
Documentation: fix sysfs-ptp
lib: scatterlist: fix Kconfig description
The big thing here is Tegra210 support, which is really only the Kconfig
symbol. Other than that there's a few miscellaneous fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=zr7c
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.5-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into late/tegra
ARM: tegra: Core SoC changes for v4.5-rc1
The big thing here is Tegra210 support, which is really only the Kconfig
symbol. Other than that there's a few miscellaneous fixes.
* tag 'tegra-for-4.5-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: select USB_ULPI from EHCI rather than platform
ARM: tegra: Ensure entire dcache is flushed on entering LP0/1
amba: Hide TEGRA_AHB symbol
soc/tegra: Add Tegra210 support
soc/tegra: Provide per-SoC Kconfig symbols
Signed-off-by: Olof Johansson <olof@lixom.net>
The firmware driver can be a loadable module, but the power domain
can only be built-in, so we get a build error in an allmodconfig
kernel:
:(.text+0x17e59c): undefined reference to `rpi_firmware_property'
:(.text+0x17e51c): undefined reference to `rpi_firmware_get'
:(.text+0x17e244): undefined reference to `rpi_firmware_property'
This changes the dependency to only allow the power domain code
to be enabled when the firmware driver is built-in. Other users
of the firmware driver may still be loadable modules and not
everyone needs the power domains, so we don't change the firmware
code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
arm-soc next/drivers branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=GinK
-----END PGP SIGNATURE-----
Merge tag 'bcm2835-drivers-next-2015-12-28' of http://github.com/anholt/linux into next/drivers
Pull "BCM2835 drivers changes for 4.5" from Eric Anholt:
This pull request includes the bcm2835 changes for 4.5 targeting the
arm-soc next/drivers branch.
* tag 'bcm2835-drivers-next-2015-12-28' of http://github.com/anholt/linux:
ARM: bcm2835: add rpi power domain driver
dt-bindings: add rpi power domain driver bindings
ARM: bcm2835: Define two new packets from the latest firmware.
ls1 has qe and ls1 has arm cpu.
move qe from arch/powerpc to drivers/soc/fsl
to adapt to powerpc and arm
Signed-off-by: Zhao Qiang <qiang.zhao@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
eventually allow am33xx and am437x to support PM with their Cortex-M3
power management processor.
This driver has been waiting to get merged for quite a while but has
had dependencies to the remoteproc that are now out of the way.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1/5M
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.5/wakeup-m3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/drivers
TI wakeup M3 IPC device driver for v4.5 merge window. This driver will
eventually allow am33xx and am437x to support PM with their Cortex-M3
power management processor.
This driver has been waiting to get merged for quite a while but has
had dependencies to the remoteproc that are now out of the way.
* tag 'omap-for-v4.5/wakeup-m3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
soc: ti: Add wkup_m3_ipc driver
Documentation: dt: add bindings for TI Wakeup M3 IPC device
Signed-off-by: Olof Johansson <olof@lixom.net>
Add regulator support for scpsys driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=pz5g
-----END PGP SIGNATURE-----
Merge tag 'v4.4-next-soc' of https://github.com/mbgg/linux-mediatek into next/drivers
Change the scpsys to builtin_platform_driver_probe.
Add regulator support for scpsys driver.
* tag 'v4.4-next-soc' of https://github.com/mbgg/linux-mediatek:
drivers/soc: make mediatek/mtk-scpsys.c explicitly non-modular
soc: mediatek: SCPSYS: Add regulator support
Signed-off-by: Olof Johansson <olof@lixom.net>
The suspend() hook in the cpuidle_ops struct is always called on
the cpu entering idle, which means that the cpu parameter passed
to the suspend hook always corresponds to the local cpu, making
it somewhat redundant.
This patch removes the logical cpu parameter from the ARM
cpuidle_ops.suspend hook and updates all the existing kernel
implementations to reflect this change.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lina Iyer <lina.iyer@linaro.org>
Tested-by: Lina Iyer <lina.iyer@linaro.org>
Tested-by: Jisheng Zhang <jszhang@marvell.com> [psci]
Cc: Lina Iyer <lina.iyer@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
