This fix alters the ordering of the IRQ and device registrations in the RTC
driver probe function. This change will apply to the RTC driver that supports
both DA9052 and DA9053 PMICs.
A problem could occur with the existing RTC driver if:
A system is started from a cold boot using the PMIC RTC IRQ to initiate a
power on operation. For instance, if an RTC alarm is used to start a
platform from power off.
The existing driver IRQ is requested before the device has been properly
registered.
i.e.
ret = da9052_request_irq()
comes before
rtc->rtc = devm_rtc_device_register();
In this case, an interrupt exists before the device has been registered and
the IRQ handler can be called immediately: this can happen be before the
memory for rtc->rtc has been allocated. The IRQ handler da9052_rtc_irq()
contains the function call:
rtc_update_irq(rtc->rtc, 1, RTC_IRQF | RTC_AF);
which in turn tries to access the unavailable rtc->rtc.
The fix is to reorder the functions inside the RTC probe. The IRQ is
requested after the RTC device resource has been registered so that
da9052_request_irq() is the last thing to happen.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
If a previously-set alarm was disabled and then triggered, it may still
be pending when a new alarm is configured.
Then, if the alarm is enabled before the pending alarm is cleared, then
an interrupt is immediately raised.
Unfortunately, when the alarm is cleared and enabled during the same I²C
block write, the chip (at least the DS1339 I have) considers that the
alarm is enabled before it is cleared, and raises an interrupt.
This patch ensures that the pending alarm is cleared before the alarm is
enabled.
Signed-off-by: Nicolas Boullis <nboullis@debian.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The i2c_smbus_read_i2c_block_data function returns 0 on success, not the
number of bytes written.
Hence, when there are 32 bytes or less to send, the
ds1307_native_smbus_write_block_data function returns 0 on success,
while it returns the number of bytes when there are more than 32.
The ds1307_write_block_data always returns the number of bytes on
success.
Signed-off-by: Nicolas Boullis <nboullis@debian.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The valid range of day of week register for DS1302 is 1 to 7. But the
set_time callback for rtc-ds1302 attempts to write the value of
tm->tm_wday which is in the range 0 to 6. While the get_time callback
correctly decodes the register.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Sergey Yanovich <ynvich@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The set_time callback for rtc-ds1302 doesn't write clock registers
because the error check for the return value from spi_write_then_read()
is not correct. spi_write_then_read() which returns zero on success.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Sergey Yanovich <ynvich@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Handle the Oscillator Failure (OF) bit on each read of date-time.
If the OF is set, an error is returned (-EINVAL) instead of the date-time.
The OF bit is cleared each time the date is set.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
To enable the wakealarm, the device must be able to wakeup.
This is done by setting the device wakeup capability to true with
'device_init_wakeup' function.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Previous 'commit c3b79770e5 ("Expire alarms after the time is set")'
and 'commit 48e9766726 ("remove disabled alarm functionality")' removed
the alarm support because the alarm irq was not functional.
Add the alarm IRQ functionality with newer functions than previous
code. Tested with 'rtctest' and the alarm is functional.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Replace the obsolete "simple_strtoul" function to "kstrtoul".
Remove some checkpatch's errors, warnings and checks :
- alignment with open parenthesis
- spaces around '<' and '<<'
- blank line after structure
- quoted string split across lines
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Replace bit shifts by BIT macro.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The driver used i2c_transfer methods to read and set date/time.
The smbus methods should be used.
This commit replaces i2c_transfer functions by i2c_smbus_XX_i2c_block_data
for reading and setting the datetime.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Remove the CONFIG_RTC_INTF_PROC and CONFIG_RTC_INTF_PROC_MODULE macro
which is not necessary anymore.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The driver used an old sysfs entry export.
Update it to use the DEVICE_ATTR_XX macro and remove the unnecessary
CONFIG_RTC_INTF_SYSFS macro.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Many drivers are defining a DRV_VERSION. This is often only used for
MODULE_VERSION and sometimes to print an info message at probe time. This
is kind of pointless as they are all versionned with the kernel anyway.
Also the core will print a message when a new rtc is found.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
mr is written twice with the same value, remove one of the
redundant assignments to mr.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
DS1302 is an half-duplex SPI device. The driver respects this fact now.
Pin configurations should be implemented using SPI subsystem.
Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
With commit 8bc2a40730 ("rtc: ds1307: add support for the
DT property 'wakeup-source'") we lost the ability for rtc irq
functionality for devices that are actually hooked on a real IRQ
line and have capability to wakeup as well. This is not an expected
behavior. So, instead of just not requesting IRQ, skip the IRQ
requirement only if interrupts are not defined for the device.
Fixes: 8bc2a40730 ("rtc: ds1307: add support for the DT property 'wakeup-source'")
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Michael Lange <linuxstuff@milaw.biz>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
while retrieving temperature from ds3231, the result may be overflow
since s16 is too small for a multiplication with 250.
ie. if temp_buf[0] == 0x2d, the result (s16 temp) will be negative.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Tested-by: Michael Tatarinov <kukabu@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Drivers:
- abx80x: handle both XT and RC oscillators, XT failure bit and autocalibration
- m41t80: avoid out of range year values
- rv8803: workaround an i2c HW issue
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PMVI
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull more RTC updates from Alexandre Belloni:
"A second pull request for v4.6 with a few fixesi before -rc1. The new
features for abx80x actually make the RTC behave correctly.
Drivers:
- abx80x: handle both XT and RC oscillators, XT failure bit and
autocalibration
- m41t80: avoid out of range year values
- rv8803: workaround an i2c HW issue"
* tag 'rtc-4.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: abx80x: handle the oscillator failure bit
rtc: abx80x: handle autocalibration
rtc: rv8803: workaround i2c HW issue
rtc: mcp795: add devicetree support
rtc: asm9260: remove incorrect __init/__exit annotations
rtc: m41t80: avoid out of range year values
rtc: s3c: Don't print an error on probe deferral
rtc: rv3029: stop mentioning rv3029c2
Handle the Oscillator Failure ('OF') bit from Oscillator Status register
(0x1D). This bit is cleared on set_time function and is read each time the
date/time is read, but only in case of XT Oscillator selection.
In RC mode, this bit is always set.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The autocalibration is separated in two bits to set in Oscillator
Control register (0x1c) :
- OSEL bit to select the oscillator type (XT or RC).
- ACAL bit to select the autocalibration type.
These functionnalities are exported in sysfs entries : "oscillator"
and "autocalibration". Respectively, the values are "xtal" for XT
oscillator and "rc" for RC oscillator and 0 to disable the
autocalibration cycle, 512 for a 512 seconds autocalibration cycle
and 1024 for a cycle of 1024 seconds.
Examples :
Set to XT Oscillator
echo xtal > /sys/class/rtc/rtc0/device/oscillator
Activate an autocalibration every 512 seconds
echo 512 > /sys/class/rtc/rtc0/device/autocalibration
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The rv8803 has a 60µs window where it will not answer on the i2c bus.
It also means there will be no ack for the communication. Make sure
communication is tried multiple times when this happens (the i2c subsystem
mandates -ENXIO is that case but the number of retries is host specific).
The critical parts are the probe function and the alarm callback so make
sure we handle the failure there.
Cc: stable@vger.kernel.org # v4.4
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add device tree support to the rtc-mcp795 driver.
Signed-off-by: Emil Bartczak <emilbart@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The probe and remove callbacks of the platform driver are marked __init
and __exit, respectively. However, this is not a correct way to annotate
them, as it will result in those sections to be discarded at link time
or after boot, while we can actually call them again based on manual
unbinding, or deferred probing.
Kbuild warns about the problem:
WARNING: drivers/rtc/rtc-asm9260.o(.data+0x0): Section mismatch in reference from the variable asm9260_rtc_driver to the function .init.text:asm9260_rtc_probe()
This removes the annotations, so we no longer branch into missing
code and avoid the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 125e550fd2 ("rtc: add Alphascale asm9260 driver")
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Avoid saving an out of range year value to the RTC. Reading that value
from the RTC again returns a totally wrong time value. For Example
$ timedatectl set-ntp no
$ timedatectl set-time "1990-01-01 12:12:00"
# Reboot
rtc-m41t80 0-0068: setting system clock to 2090-01-01 12:12:35 UTC (3786955955)
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The clock and source clock looked up by the driver may not be available
just because the clock controller driver was not probed yet so printing
an error in this case is not correct and only adds confusion to users.
However, knowing that a driver's probe was deferred may be useful so it
can be printed as a debug information.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
drivers/rtc: broken link fix
drm/i915 Fix typos in i915_gem_fence.c
Docs: fix missing word in REPORTING-BUGS
lib+mm: fix few spelling mistakes
MAINTAINERS: add git URL for APM driver
treewide: Fix typo in printk
There are only a few differences between PCF2127 and PCF2129 (PCF2127
has 512 bytes of general purpose SRAM and count-down timer).
The rtc-pcf2127 driver currently doesn't use the PCF2127 specific
functionality and Kconfig help text already says this driver supports
PCF2127/29, so we can simply add pcf2129 to device id list.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
pcf2127 has selectable I2C-bus and SPI-bus interface support.
This adds support for SPI interface.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
pcf2127 has selectable I2C-bus and SPI-bus interface support.
Currently rtc-pcf2127 driver only supports I2C.
This is preparation for support for SPI interface.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This adds support to
- enable/disable the thermometer
- set the temperature scanning interval
- read the current temperature that is used for temp compensation.
via hwmon interface
Signed-off-by: Michael Buesch <m@bues.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This simplifies the update of single bits in the eeprom.
Signed-off-by: Michael Buesch <m@bues.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
objtool reports the following warnings:
drivers/rtc/rtc-ds1685.o: warning: objtool: ds1685_rtc_work_queue()+0x0: duplicate frame pointer save
drivers/rtc/rtc-ds1685.o: warning: objtool: ds1685_rtc_work_queue()+0x3: duplicate frame pointer setup
drivers/rtc/rtc-ds1685.o: warning: objtool: ds1685_rtc_work_queue()+0x0: frame pointer state mismatch
The warning message needs to be improved, but what it really means in
this case is that ds1685_rtc_poweroff() has a possible code path where
it can actually fall through to the next function in the object code,
ds1685_rtc_work_queue().
The bug is caused by the use of the unreachable() macro in a place which
is actually reachable. That causes gcc to assume that the printk()
immediately before the unreachable() macro never returns, when in fact
it does. So gcc places the printk() at the very end of the function's
object code. When the printk() returns, the next function starts
executing.
The surrounding comment and printk message state that the code should
spin forever, which explains the unreachable() statement. However the
actual spin code is missing.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Year field must be in BCD format, according to
hym8563 datasheet.
Due to the bug year 2016 became 2010.
Fixes: dcaf038493 ("rtc: add hym8563 rtc-driver")
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
ds3232->mutex is used to protect for alarm operations which
need to access status and control registers.
But we can use rtc->ops_lock instead. rtc->ops_lock is held when most
of rtc_class_ops methods are called, so we only need to explicitly
acquire it from irq handler in order to protect form concurrent
accesses.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
ds3232-core requests irq with IRQF_SHARED, so irq can be shared by
several devices. But the irq handler for ds3232 unconditionally
disables the irq at first and the irq is re-enabled only when the
interrupt source was the ds3232's alarm. This behaviour breaks the
devices sharing the same irq in the various scenarios.
This converts to use threaded irq and remove outdated code in
suspend/resume paths.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Suggested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
UIE mode irqs are handled by the generic rtc core now. But there are
remaining unused code fragments for it.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add missing register access error checks and make it return error code
or print error message.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The rtctest (tools/testing/selftests/timers/rtctest.c) found that
reading ds3232 rtc device immediately return the value 0x20 (RTC_AF)
without waiting alarm interrupt.
This is because alarm_irq_enable() of ds3232 driver changes RTC_AF
flag in rtc->irq_data. So calling ioctl with RTC_AIE_ON generates
invalid value in rtc device.
The lower-level driver should not touch rtc->irq_data directly.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
According to "Feature Comparison of the DS323x Real-Time Clocks"
(http://pdfserv.maximintegrated.com/en/an/AN5143.pdf), DS3232 and
DS3234 are very similar.
This merges rtc-ds3232 and rtc-ds3234 with using regmap.
This change also enables to support alarm for ds3234.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Suggested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The trickle charger resistor can be enabled via device tree
property trickle-resistor-ohms.
Signed-off-by: Michael Buesch <m@bues.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This adds functions for access to the EEPROM memory on the rv3029.
Signed-off-by: Michael Buesch <m@bues.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This adds all (according to the data sheet) missing register and bit
definitions.
It also fixes the definition of the trickle charger bit masks.
Signed-off-by: Michael Buesch <m@bues.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The C2 suffix does not appear in the latest datasheet, so add
a device ID without it.
Signed-off-by: Michael Buesch <m@bues.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The C2 suffix does not appear anymore in the latest device and
data sheet versions.
Signed-off-by: Michael Buesch <m@bues.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
There are several arch-specific RTC drivers that can be successfully
compiled on other platforms. Add a COMPILE_TEST dependency for those.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
There are four architectures using this driver, but since we can
build it with COMPILE_TEST, we should try dealing with the absence
of the asm/rtc.h header file, to avoid getting a build error:
drivers/rtc/rtc-generic.c:12:21: fatal error: asm/rtc.h: No such file or directory
This creates an alternative use of the driver, allowing architectures
to pass a set of rtc_class_ops in platform data. We can convert the
four architectures to use this and then remove the original
code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The time and date register of the pcf8223 are undefined after a power
reset. Properly handle the OS bit and return -EINVAL when that bit is set.
It is properly removed when setting the time.
This solves an issue where the time and date may be valid for
rtc_valid_tm() but is not the current time.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
No members of struct pcf85063 are used anymore, remove the whole structure.
Reviewed-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
We call spin_lock_irqrestore with "flags" set to zero instead of to the
value from spin_lock_irqsave().
Fixes: aaaf5fbf56 ('rtc: add driver for DS1685 family of real time clocks')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Use macro REGMAP_IRQ_REG from regmap.h to initialise the
regmap irq table for max77686 to have better coding style
and improve readability.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Maxim Semiconductor's PMIC MAX77686 has RTC IP which is
reused in the MAX77620/MAX20024 PMICs.
Add support for these devices in MAX77686 RTC driver. This
device does not have RTC alarm pending status outside of
RTC IP. The RTC IP is having separate I2C address for its
register access.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The driver uses the MODULE_ALIAS() macro to export a platform module alias
to allow the module to be autoloaded if the device is registered using the
legacy platform registration mechanism but the driver is always used by OF
only machines so the alias is not needed and should just be removed.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
pcf85063_get_datetime() tries to handle a century bit but that bit is not
documented and the final value is never used anywhere else in the kernel.
Reviewed-by: Juergen Borleis <jbe@pengutronix.de>
Tested-by: Ulrich Ölmann <u.oelmann@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
drivers/rtc/rtc-vr41xx.c:229: warning: ‘vr41xx_rtc_alarm_irq_enable’ defined but not used
Apparently the conversion to alarm_irq_enable forgot to wire up the
callback.
Fixes: 16380c153a ("RTC: Convert rtc drivers to use the alarm_irq_enable method")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The Kconfig option for rv3029 is not mentioning any part number, explicitly
show rv3029.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
as3722 RTC IRQ is nested threaded and wired to the as3722 inerrupt
controller. So, this flag is not required for nested irqs anymore,
since commit 3c646f2c6a ("genirq: Don't suspend nested_thread irqs
over system suspend") was merged.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
tps80031 RTC IRQ is nested threaded and wired to the tps80031
inerrupt controller. So, this flag is not required for nested irqs
anymore, since commit 3c646f2c6a ("genirq: Don't suspend
nested_thread irqs over system suspend") was merged.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
tps65910 RTC IRQ is nested threaded and wired to the tps65910 inerrupt
controller. So, this flag is not required for nested irqs anymore,
since commit 3c646f2c6a ("genirq: Don't suspend nested_thread irqs
over system suspend") was merged.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
tps6586x RTC IRQ is nested threaded and wired to the tps6586x inerrupt
controller. So, this flag is not required for nested irqs anymore,
since commit 3c646f2c6a ("genirq: Don't suspend nested_thread irqs
over system suspend") was merged.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Palams RTC IRQ is nested threaded and wired to the Palmas inerrupt
controller. So, this flag is not required for nested irqs anymore,
since commit 3c646f2c6a ("genirq: Don't suspend nested_thread irqs
over system suspend") was merged.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The RTC entries are mostly grouped by vendor. Move the few outliers in
place.
Also, change the one occurrence of 'nxp' to 'NXP' to make all NXP
entries consistent.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This driver adds support for the PIC32 real time clock and calendar
peripheral:
- reading and setting time
- alarms provided by dedicated IRQ
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The alarm for rx8025 only has a minute accuracy, so unsupport UIE mode.
pcf8563 and hym8563 also have a minute accuracy and unsupport it.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The alarm for rx8025 only has a minute accuracy, so round up to nearest
minute when setting alarm. Without doing this, rtctest blocks one day
after setting alarm to 5 seconds later.
pcf8563 and hym8563 also have similar handling.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The ctrl1 register is accessed by alarm operations. But it is updated
in threaded interrupt handler without acquiring rtc->ops_lock.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
When IRQ line for this chips is connected, devm_request_threaded_irq()
refuses to register irq handler with the following message.
genirq: Threaded irq requested with handler=NULL and !ONESHOT for irq
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Few functions were marked inline even though they were relatively large
and sometimes used in multiple places. De-inline them to let the
compiler decide whether optimization makes sense. This fixes inline_hunt
report:
drivers/rtc/rtc-s5m.c: Deinline s5m8767_rtc_set_alarm_reg, save 704 bytes
drivers/rtc/rtc-s5m.c: Deinline s5m8767_wait_for_udr_update, save 192 bytes
Reported-by: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The Makefile/Kconfig currently controlling compilation of this code is:
obj-$(CONFIG_RTC_CLASS) += rtc-core.o
rtc-core-y := class.o interface.o
drivers/rtc/Kconfig:menuconfig RTC_CLASS
drivers/rtc/Kconfig: bool "Real Time Clock"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the code there is no doubt it is builtin-only.
We don't replace module.h with init.h since the file does need
to know what a struct module is.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
When setting a new time/date the RTC's clock must be stopped first, in
order to write the time/date registers in an atomic manner.
So, this change stops the clock first and then writes the time/date
registers and the clock control register (to re-enable the clock) in one
turn.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Check if the RTC signals an invalid time/date (due to a battery power loss
for example). In this case ignore the time/date until it is really set again.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
By using i2c_smbus_read_i2c_block_data() the code is now much simpler.
While at it: when reading the RTC's seconds register, all time/date registers
are frozen until the RTC's year register is read. So it is important to read
all time/date registers in one turn to not lose a second event. Make it more
clear why the read must happen in this way.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
pcf2123 has an offset register, which can be used to make minor
adjustments to the clock rate to compensate for temperature or
a crystal that is not exactly right.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
clock offset may be set and read in decimal parts per billion
attribute is /sys/class/rtc/rtcN/offset
The attribute is only visible for rtcs that have set_offset implemented.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
A number of rtc devices, such as the NXP pcf2123 include a facility
to adjust the clock in order to compensate for temperature or a
crystal, capacitor, etc, that results in the rtc clock not running
at exactly 32.768 kHz.
Data sheets I have seen refer to this as a clock offset, and measure it
in parts per million, however they often reference ppm to 2 digits of
precision, which makes integer ppm less than ideal.
We use parts per billion, which more than covers the precision needed
and works nicely within 32 bits
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fix a scheduling while atomic issue caused by rv8803_set_time()
holding a spinlock during the call to i2c_smbus_read_byte_data().
Signed-off-by: Oleksij Rempel <fixed-term.Oleksij.Rempel@de.bosch.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add support for RTC controller found on Alphascale asm9260
SoC.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
DS3231 has programmable square-wave output signal.
This enables to use this feature as a clock provider of
common clock framework.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
To make RTC block of MAX77686/MAX77802 as independent driver,
move the registration of i2c device, regmap for register access
and irq_chip for interrupt support inside the RTC driver.
Removed the same initialisation from MFD driver.
Having this change will allow to reuse this driver for different
PMIC/devices from Maxim Semiconductor if they kept same RTC IP on
different PMIC. Some of examples as PMIC MAX77620, MAX20024 where
same RTC IP used and hence driver for these chips will use this
driver only for RTC support.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Get rid of referring parent device info for register access
all the places by making regmap as part of max77686 rtc
device info. This will also remove the need of storing parent
device info in max77686 rtc device info as this is no more required.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
rtc_regmap should be used to access all RTC registers instead
of parent regmap regardless of what chip or property have it.
This makes the register access uniform and extendible for other
chips.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fix following check patch error in rtc-max77686 driver:
- Alignment should match open parenthesis.
- braces {} should be used on all arms of this statement.
- Prefer using the BIT macro
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
At the moment the "sun6i" RTC drivers depends on having two specific
SoC families selected.
The Allwinner A64 SoC has the same RTC, so extend the Kconfig option
to allow inclusion of the driver for all Allwinner SoCs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The RX6110 comes in two different variants: SPI and I2C.
This driver only supports the SPI variant.
If the need ever arises to also support the I2C variant, this driver
could easily be refactored to support both cases.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
pcf2123 data sheet recommends a software reset when the chip
is first powered on. This change avoids resetting the chip
every time the driver is loaded, which has some negative effects.
There are several registers including a clock rate adjustment that really
should survive a reload of the driver (or reboot).
In addition, stopping and restarting the clock to verify the chip is
there is not a good thing once the time is set.
According to the data sheet, the seconds register has a 1 in
the high bit when the voltage has gotten low. We check for this
condition, as well as whether the time retrieved from the chip is
valid. We reset the rtc only if the time is not reliable and valid.
This is sufficient for checking for the presence of the chip,
as either all zeros or all 0xff will result in an invalid time/date
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Refactor chip reset items into its own function, isolating it from
the rest of the device probe.
Subsequent commits will avoid calling this code.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add new functions pcf2123_write(), and pcf2123_write_reg().
Use named defines for the values being written.
This improves modularity and readability, and reduces lines of code.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Put read operations into a function.
This improves modularity and readability.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add defines for all 16 registers in the pcf2123.
Add defines for useful bits from several registers
I've tried to document all the registers, and
as best as possible, all the special bits they employ
Use BIT() wherever possible in the bit definitions
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
In drivers/rtc/rtc-rx8025.c is a broken link that is supposed to
lead to a form allowing users to subscribe to the lm-sensors mailing list.
The link <http://lists.lm-sensors.org/mailman/listinfo/lmsensors> leads
to a page with a 404 error. I believe the link should be replaced
with <lm-sensors@lm-sensors.org>.
Signed-off-by: Leslie Lau <laulinxk@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
DS3231 has the temperature registers with a resolution of 0.25
degree celsius. This enables to get the value through hwmon.
# cat /sys/class/i2c-adapter/i2c-2/2-0068/hwmon/hwmon0/temp1_input
21000
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
For RTC chips with no IRQ directly connected to the SoC, the RTC chip
can be forced as a wakeup source by stating that explicitly in
the device's .dts file using the "wakeup-source" boolean property.
This will guarantee the 'wakealarm' sysfs entry is available on the
device, if supported by the RTC.
With these changes to the driver rtc-ds1307 and the necessary entries
in the .dts file, I get an working ds1337 RTC on the Witty Pi extension
board by UUGear for the Raspberry Pi.
An example for the entry in the .dts file:
rtc: ds1337@68 {
compatible = "dallas,ds1337";
reg = <0x68>;
wakeup-source;
If the "wakeup-source" property is set, do not request an IRQ.
Set also UIE mode to unsupported, to get a working 'hwclock' binary.
Signed-off-by: Michael Lange <linuxstuff@milaw.biz>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The mt6397 RTC driver can be built either when the MFD_MT6397 driver
is enabled (which selects IRQ_DOMAIN), or when compile testing.
The latter however fails without IRQ domains:
drivers/rtc/rtc-mt6397.c: In function 'mtk_rtc_probe':
drivers/rtc/rtc-mt6397.c:326:13: error: implicit declaration of function 'irq_create_mapping' [-Werror=implicit-function-declaration]
rtc->irq = irq_create_mapping(mt6397_chip->irq_domain, res->start);
This adds an explicit dependency for the COMPILE_TEST case.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The rv8803 has its own driver that should be used. Remove its id from
the rx8025 driver.
Fixes: b1f9d790b5
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
For better readability, use to_spi_device() and kobj_to_dev() instead
of container_of().
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cleanup of entire driver of its dmesg output:
1. Remove printing of the function name, because printing device name is
sufficient. This also makes the dev_err()-like functions more compact
and readable (not need of line break).
2. Lower from info to debug printing of each RTC interrupt (no need to
make noise on each alarm).
3. Remove dev_info() at beginning of probe because a message is already
always printed by either probe failure or from registering the RTC
device as /dev/rtcX.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The max77686 RTC driver now supports the max77802 RTC as
well so there's no need to have a separate driver anymore.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The regmap_irq_get_virq() can return 0 or -EINVAL in error conditions
but driver checked only for value of 0.
This could lead to a cast of -EINVAL to an unsigned int used as a
interrupt number for devm_request_threaded_irq(). Although this is not
yet fatal (devm_request_threaded_irq() will just fail with -EINVAL) but
might be a misleading when diagnosing errors.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 6f1c1e71d9 ("mfd: max77686: Convert to use regmap_irq")
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The max77686 RTC only supports a range of 99 years so instead of using
year 1900 as the base, the year 2000 is used. This means that 1900 to
1999 are unsupported years.
The driver was printing a warning for those values but was returning a
error so for consistency, print an error message instead and don't say
that a year 2000 is assumed, since the year is not set.
Also, it is better to use dev_* log functions instead of pr_* to print
information about the device in the kernel log in a standardized way.
This also allows to remove the local pr_fmt() defined macro.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The MAX77686 and MAX77802 RTC IP blocks are very similar with only
these differences:
0) The RTC registers layout and addresses are different.
1) The MAX77686 use 1 bit of the sec/min/hour/etc registers as the
alarm enable while MAX77802 has a separate register for that.
2) The MAX77686 RTCYEAR register valid values range is 0..99 while
for MAX77802 is 0..199.
3) The MAX77686 has a separate I2C address for the RTC registers
while the MAX77802 uses the same I2C address as the PMIC regs.
5) The minimum delay before a RTC update (16 msecs vs 200 usecs).
There are separate drivers for MAX77686 and MAX77802 RTC IP blocks
but the differences are not that big so the driver can be extended
to support both instead of duplicating a lot of code in 2 drivers.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The max77686 driver is generic enough that can be used for other
Maxim RTC IP blocks but these might not have the same registers
layout so instead of accessing the registers directly, add a map
to translate offsets to the real registers addresses for each IP.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The driver has some hard-coded values such as the minimum delay needed
before a RTC update or the mask used for the sec/min/hour/etc registers.
Use a data structure that contains these values and pass as driver data
using the platform device ID table for each device.
This allows to make the driver's ops callbacks more generic so other RTC
that are similar but don't have the same values can also be supported.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Documentation/timers/timers-howto.txt suggest to use usleep_range()
instead of msleep() for small msec (1ms - 20ms) since msleep() will
often sleep for 20ms for any value in that range.
This is fine in this case since 16ms is the _minimum_ delay required
by max77686 for an RTC update but by using usleep_range() instead of
msleep(), the driver can support other RTC IP blocks with a shorter
minimum delay (i.e: in the range of usecs instead of msecs).
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
It is better to use the ARRAY_SIZE() macro instead of the array length
to avoid bugs if the array is later changed and the length not updated.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The function is always returning zero even in case of failures since
the ret value was not propagated to the callers. Fix the error path.
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
- Ground work for the new Power9 MMU from Aneesh Kumar K.V
- Optimise FP/VMX/VSX context switching from Anton Blanchard
- Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica Gupta,
Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling, Andrew Donnellan
- Allow wrapper to work on non-english system from Laurent Vivier
- Add rN aliases to the pt_regs_offset table from Rashmica Gupta
- Fix module autoload for rackmeter & axonram drivers from Luis de Bethencourt
- Include KVM guest test in all interrupt vectors from Paul Mackerras
- Fix DSCR inheritance over fork() from Anton Blanchard
- Make value-returning atomics & {cmp}xchg* & their atomic_ versions fully ordered from Boqun Feng
- Print MSR TM bits in oops messages from Michael Neuling
- Add TM signal return & invalid stack selftests from Michael Neuling
- Limit EPOW reset event warnings from Vipin K Parashar
- Remove the Cell QPACE code from Rashmica Gupta
- Append linux_banner to exception information in xmon from Rashmica Gupta
- Add selftest to check if VSRs are corrupted from Rashmica Gupta
- Remove broken GregorianDay() from Daniel Axtens
- Import Anton's context_switch2 benchmark into selftests from Michael Ellerman
- Add selftest script to test HMI functionality from Daniel Axtens
- Remove obsolete OPAL v2 support from Stewart Smith
- Make enter_rtas() private from Michael Ellerman
- PPR exception cleanups from Michael Ellerman
- Add page soft dirty tracking from Laurent Dufour
- Add support for Nvlink NPUs from Alistair Popple
- Add support for kexec on 476fpe from Alistair Popple
- Enable kernel CPU dlpar from sysfs from Nathan Fontenot
- Copy only required pieces of the mm_context_t to the paca from Michael Neuling
- Add a kmsg_dumper that flushes OPAL console output on panic from Russell Currey
- Implement save_stack_trace_regs() to enable kprobe stack tracing from Steven Rostedt
- Add HWCAP bits for Power9 from Michael Ellerman
- Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V
- Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins
- scripts/recordmcount.pl: support data in text section on powerpc from Ulrich Weigand
- Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand
- cxl: Fix possible idr warning when contexts are released from Vaibhav Jain
- cxl: use correct operator when writing pcie config space values from Andrew Donnellan
- cxl: Fix DSI misses when the context owning task exits from Vaibhav Jain
- cxl: fix build for GCC 4.6.x from Brian Norris
- cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris
- cxl: Enable PCI device ID for future IBM CXL adapter from Uma Krishnan
- Freescale updates from Scott: Highlights include moving QE code out of
arch/powerpc (to be shared with arm), device tree updates, and minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R5bX
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Core:
- Ground work for the new Power9 MMU from Aneesh Kumar K.V
- Optimise FP/VMX/VSX context switching from Anton Blanchard
Misc:
- Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica
Gupta, Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling,
Andrew Donnellan
- Allow wrapper to work on non-english system from Laurent Vivier
- Add rN aliases to the pt_regs_offset table from Rashmica Gupta
- Fix module autoload for rackmeter & axonram drivers from Luis de
Bethencourt
- Include KVM guest test in all interrupt vectors from Paul Mackerras
- Fix DSCR inheritance over fork() from Anton Blanchard
- Make value-returning atomics & {cmp}xchg* & their atomic_ versions
fully ordered from Boqun Feng
- Print MSR TM bits in oops messages from Michael Neuling
- Add TM signal return & invalid stack selftests from Michael Neuling
- Limit EPOW reset event warnings from Vipin K Parashar
- Remove the Cell QPACE code from Rashmica Gupta
- Append linux_banner to exception information in xmon from Rashmica
Gupta
- Add selftest to check if VSRs are corrupted from Rashmica Gupta
- Remove broken GregorianDay() from Daniel Axtens
- Import Anton's context_switch2 benchmark into selftests from
Michael Ellerman
- Add selftest script to test HMI functionality from Daniel Axtens
- Remove obsolete OPAL v2 support from Stewart Smith
- Make enter_rtas() private from Michael Ellerman
- PPR exception cleanups from Michael Ellerman
- Add page soft dirty tracking from Laurent Dufour
- Add support for Nvlink NPUs from Alistair Popple
- Add support for kexec on 476fpe from Alistair Popple
- Enable kernel CPU dlpar from sysfs from Nathan Fontenot
- Copy only required pieces of the mm_context_t to the paca from
Michael Neuling
- Add a kmsg_dumper that flushes OPAL console output on panic from
Russell Currey
- Implement save_stack_trace_regs() to enable kprobe stack tracing
from Steven Rostedt
- Add HWCAP bits for Power9 from Michael Ellerman
- Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V
- Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins
- scripts/recordmcount.pl: support data in text section on powerpc
from Ulrich Weigand
- Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand
cxl:
- cxl: Fix possible idr warning when contexts are released from
Vaibhav Jain
- cxl: use correct operator when writing pcie config space values
from Andrew Donnellan
- cxl: Fix DSI misses when the context owning task exits from Vaibhav
Jain
- cxl: fix build for GCC 4.6.x from Brian Norris
- cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris
- cxl: Enable PCI device ID for future IBM CXL adapter from Uma
Krishnan
Freescale:
- Freescale updates from Scott: Highlights include moving QE code out
of arch/powerpc (to be shared with arm), device tree updates, and
minor fixes"
* tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (149 commits)
powerpc/module: Handle R_PPC64_ENTRY relocations
scripts/recordmcount.pl: support data in text section on powerpc
powerpc/powernv: Fix OPAL_CONSOLE_FLUSH prototype and usages
powerpc/mm: fix _PAGE_SWP_SOFT_DIRTY breaking swapoff
powerpc/mm: Fix _PAGE_PTE breaking swapoff
cxl: Enable PCI device ID for future IBM CXL adapter
cxl: use -Werror only with CONFIG_PPC_WERROR
cxl: fix build for GCC 4.6.x
powerpc: Add HWCAP bits for Power9
powerpc/powernv: Reserve PE#0 on NPU
powerpc/powernv: Change NPU PE# assignment
powerpc/powernv: Fix update of NVLink DMA mask
powerpc/powernv: Remove misleading comment in pci.c
powerpc: Implement save_stack_trace_regs() to enable kprobe stack tracing
powerpc: Fix build break due to paca mm_context_t changes
cxl: Fix DSI misses when the context owning task exits
MAINTAINERS: Update Scott Wood's e-mail address
powerpc/powernv: Fix minor off-by-one error in opal_mce_check_early_recovery()
powerpc: Fix style of self-test config prompts
powerpc/powernv: Only delay opal_rtc_read() retry when necessary
...
The Microsoft Surface 3 tablet shares interrupt line between RTC and one of SPI
controllers. However, the rtc_cmos driver doesn't allow shared interrupts and
user sees the following warning
genirq: Flags mismatch irq 8. 00000080 (8086228E:02) vs. 00000000 (rtc0)
...
[<ffffffffa004eb01>] pxa2xx_spi_probe+0x151/0x600 [spi_pxa2xx_platform]
Allow RTC driver to use shared interrupts.
Seems we are on the safe side to do just this simple change since
cmos_interrupt() handler checks for the actual hardware status anyway.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The ds2404_chip_ops structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Before updating time and alarm the driver must set appropriate mask in
UDR register. For that purpose the driver uses common register
configuration and a lot of exceptions per device in the code. The
exceptions are not obvious, for example except the change in the logic
sometimes the fields are swapped (WUDR and AUDR between S2MPS14 and
S2MPS15). This leads to quite complicated code.
Try to make it more obvious by:
1. Documenting the UDR masks for devices and operations.
2. Adding fields in register configuration structure for each operation
(read time, write time and alarm).
3. Splitting the configuration per S2MPS13, S2MPS14 and S2MPS15 thus
removing exceptions for them.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Some devices from S2M/S5M family use different register update masks for
different operations (alarm and register update). Now the driver uses
common register configuration and a lot of exceptions per device in code.
Before eliminating the exceptions and using specific register
configuration for given device, make the auto-cleared mask a separate
field. This is merely a refactoring.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Remove the 'rtc' prefix from some of the fields in struct
s5m_rtc_reg_config because it is obvious - this is a RTC driver. No
functional changes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The simple_strtoul function is obsolete.
This patch replace it by kstrtoul.
Since kstrtoul is more strict, it permits to filter some invalid input that
simple_strtoul accept. For example:
echo '1022xxx' > /sys/devices/pnp0/00:03/rtc/rtc0/max_user_freq
cat /sys/devices/pnp0/00:03/rtc/rtc0/max_user_freq
1022
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The v3020_chip_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The Seiko Epson's RTC RX8900 layout register is compatible with the
RV8803. So let's add its ID in order to reuse the same driver.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The function can return negative values, so its result should
be assigned to signed variable.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This driver supports the following functions:
- reading and setting time
- alarms when connected to an IRQ
- reading and clearing the voltage low flags
Datasheet:
http://www.epsondevice.com/docs/qd/en/DownloadServlet?id=ID000956
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
If the driver is used on an ARM platform with SPARSE_IRQ defined,
semantics of NR_IRQS is different (minimal value of virtual irqs)
and by default it is set to 16, see arch/arm/include/asm/irq.h.
This value may be less than the actual number of virtual irqs, which
may break the driver initialization. The check removal allows to use
the driver on such a platform, and, if irq controller driver works
correctly, the check is not needed on legacy platforms.
Fixes a runtime problem:
rtc-lpc32xx 40024000.rtc: Can't get interrupt resource
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Minor issue, fix spelling mistake, happend -> happened
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
...and don't do it wrong.
"not ok or N/A" has length 13. Add the trailing newline, and the
snprintf return value will be 14. However, we lied to snprintf and
told it that only 13 bytes were available. Hence snprintf has only
written "not ok or N/" and a trailing '\0' to the buffer. Next we
continue lying, this time to the upper sysfs layer, claiming that we
wrote 14 meaningful bytes to the buffer. That'll make the upper layer
copy "not ok or N/" plus two nul bytes to user space (one nul byte
from snprintf, the other since sysfs takes care to clear the buffer
before giving it to the ->show method).
In the other cases, the claimed buffer size is closer to sufficient,
but we'll still get a nul byte instead of a newline written to user
space. There's absolutely no reason to try to predict the output
size, and there's plenty of room in the buffer, so just use sprintf.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This makes the generated code slightly smaller.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
driver did
| static void da9063_tm_to_data(struct rtc_time *tm, u8 *data,
| {
| const struct da9063_compatible_rtc_regmap *config = rtc->config;
|
| data[RTC_SEC] &= ~config->rtc_count_sec_mask;
| data[RTC_SEC] |= tm->tm_sec & config->rtc_count_sec_mask;
| ...
| }
| ...
| static int da9063_rtc_set_time(struct device *dev, struct rtc_time *tm)
| {
| ...
| u8 data[RTC_DATA_LEN];
| int ret;
|
| da9063_tm_to_data(tm, data, rtc);
which means that some bits of stack content (in 'data[]') was masked out
and written to the RTC.
Because da9063_tm_to_data() is used only by da9063_rtc_set_time() and
da9063_rtc_set_alarm(), we can write fields directly.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The data_year_param struct is never modified, so lets constify it.
This permit to remove cast since of_device_id is const also.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The variable year must be set as unsigned since it is used with
sunxi_rtc_data_year{.min|.max} and as parameter of is_leap_year() which
wait for unsigned int.
Only tm_year is not unsigned, but it is long.
This patch fix also the format of printing of min/max. (must use %u since
they are unsigned)
The parameter to of sunxi_rtc_setaie() must be set to uint since callers
give always uint data.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The driver core clears the driver data to NULL after device_release
or on probe failure
Signed-off-by: Nizam Haider <nijamh@cdac.in>
Acked-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add efi_procfs in efi_rtc_ops to show rtc-efi info in /proc/driver/rtc.
Most of the code comes from efi_rtc_proc_show() in efirtc.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
rtc-proc.c is not built as a module. Thus, rather than dealing with
THIS_MODULE's reference count, we should deal with rtc->owner's
reference count.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
When the chip increments the YEAR register and it already holds
bin2bcd(99) it reads as 0 afterwards. With this behaviour the last valid
day (without trickery) that has a representation is 2099-12-31 23:59:59.
So refuse to write later dates.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This fix alters the ordering of the IRQ and device registrations in the RTC
driver probe function. This change will apply to the RTC driver that supports
both DA9063 and DA9062 PMICs.
A problem could occur with the existing RTC driver if:
A system is started from a cold boot using the PMIC RTC IRQ to initiate a
power on operation. For instance, if an RTC alarm is used to start a
platform from power off.
The existing driver IRQ is requested before the device has been properly
registered.
i.e.
ret = devm_request_threaded_irq()
comes before
rtc->rtc_dev = devm_rtc_device_register();
In this case, the interrupt can be called before the device has been
registered and the handler can be called immediately. The IRQ handler
da9063_alarm_event() contains the function call
rtc_update_irq(rtc->rtc_dev, 1, RTC_IRQF | RTC_AF);
which in turn tries to access the unavailable rtc->rtc_dev.
The fix is to reorder the functions inside the RTC probe. The IRQ is
requested after the RTC device resource has been registered so that
get_irq_byname is the last thing to happen.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
In A.D. 1582 Pope Gregory XIII found that the existing Julian calendar
insufficiently represented reality, and changed the rules about
calculating leap years to account for this. Similarly, in A.D. 2013
Rockchip hardware engineers found that the new Gregorian calendar still
contained flaws, and that the month of November should be counted up to
31 days instead. Unfortunately it takes a long time for calendar changes
to gain widespread adoption, and just like more than 300 years went by
before the last Protestant nation implemented Greg's proposal, we will
have to wait a while until all religions and operating system kernels
acknowledge the inherent advantages of the Rockchip system. Until then
we need to translate dates read from (and written to) Rockchip hardware
back to the Gregorian format.
This patch works by defining Jan 1st, 2016 as the arbitrary anchor date
on which Rockchip and Gregorian calendars are in sync. From that we can
translate arbitrary later dates back and forth by counting the number
of November/December transitons since the anchor date to determine the
offset between the calendars. We choose this method (rather than trying
to regularly "correct" the date stored in hardware) since it's the only
way to ensure perfect time-keeping even if the system may be shut down
for an unknown number of years. The drawback is that other software
reading the same hardware (e.g. mainboard firmware) must use the same
translation convention (including the same anchor date) to be able to
read and write correct timestamps from/to the RTC.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
GregorianDay() is supposed to calculate the day of the week
(tm->tm_wday) for a given day/month/year. In that calcuation it
indexed into an array called MonthOffset using tm->tm_mon-1. However
tm_mon is zero-based, not one-based, so this is off-by-one. It also
means that every January, GregoiranDay() will access element -1 of
the MonthOffset array.
It also doesn't appear to be a correct algorithm either: see in
contrast kernel/time/timeconv.c's time_to_tm function.
It's been broken forever, which suggests no-one in userland uses
this. It looks like no-one in the kernel uses tm->tm_wday either
(see e.g. drivers/rtc/rtc-ds1305.c:319).
tm->tm_wday is conventionally set to -1 when not available in
hardware so we can simply set it to -1 and drop the function.
(There are over a dozen other drivers in drivers/rtc that do
this.)
Found using UBSAN.
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andrew Morton <akpm@linux-foundation.org> # as an example of what UBSan finds.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: rtc-linux@googlegroups.com
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With the actual code, read_alarm() always returns -EINVAL when called
during the RTC device registration. This prevents from retrieving an
already configured alarm in hardware.
This patch fixes the issue by moving the HAS_ALARM bit configuration
(if supported by the hardware) above the rtc_device_register() call.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Since commit 3fffd12839 ("i2c: allow specifying
separate wakeup interrupt in device tree") we have
automatic wakeup irq support for i2c devices. That
commit missed the fact that rtc-1307 had its own
wakeup irq handling and ended up introducing a
kernel splat for at least Beagle x15 boards.
Fix that by reverting original commit _and_ passing
correct interrupt names on DTS so i2c-core can
choose correct IRQ as wakeup.
Now that we have automatic wakeirq support, we can
revert the original commit which did it manually.
Fixes the following warning:
[ 10.346582] WARNING: CPU: 1 PID: 263 at linux/drivers/base/power/wakeirq.c:43 dev_pm_attach_wake_irq+0xbc/0xd4()
[ 10.359244] rtc-ds1307 2-006f: wake irq already initialized
Cc: Tony Lindgren <tony@atomide.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
RTC found in s2mps15 is almost same as one found on s2mps13
with few differences in RTC_UPDATE register fields, like:
1> Bit[4] and Bit[1] are reversed
- On s2mps13
WUDR -> bit[4], AUDR -> bit[1]
- On s2mps15
WUDR -> bit[1], AUDR -> bit[4]
2> In case of s2mps13, for alarm register, need to set both
WDUR and ADUR high, whereas for s2mps15 only set AUDR to high.
3> On s2mps15, WUDR, RUDR and AUDR functions should never be used
at the same time.
This patch add required changes to enable s2mps15 rtc timer.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Core:
- Fix rtctest error path
New drivers:
- Microcrystal RV8803
Subsystem wide cleanups:
- remove misuse of IRQF_NO_SUSPEND flag
Drivers:
- at91rm9200: clear RTC alarm status flag prior to suspending
- davinci: remove incorrect reference to probe function
- ds1307: Fix alarm programming for mcp794xx
- ds1390: trickle charger support, fix ds1390_get_reg
- isl1208: Pass the IRQF_ONESHOT flag
- opal: fix type of token
- pcf2127: fix RTC_READ_VL, remove useless driver version
- pcf85063: return an error when date is invalid
- pcf8563: add CLKOUT to common clock framework
- rx8025: remove unnecessary braces
- s3c: Set year, month, day value for setting alarm
- stmp3xxx: unify register access macros
- License fixes: pcf2127, da9063
- wakeup-source support for isl12057 and opal
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=sY2D
-----END PGP SIGNATURE-----
Merge tag 'rtc-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Core:
- Fix rtctest error path
New drivers:
- Microcrystal RV8803
Subsystem wide cleanups:
- remove misuse of IRQF_NO_SUSPEND flag
Drivers:
- at91rm9200: clear RTC alarm status flag prior to suspending
- davinci: remove incorrect reference to probe function
- ds1307: Fix alarm programming for mcp794xx
- ds1390: trickle charger support, fix ds1390_get_reg
- isl1208: Pass the IRQF_ONESHOT flag
- opal: fix type of token
- pcf2127: fix RTC_READ_VL, remove useless driver version
- pcf85063: return an error when date is invalid
- pcf8563: add CLKOUT to common clock framework
- rx8025: remove unnecessary braces
- s3c: Set year, month, day value for setting alarm
- stmp3xxx: unify register access macros
- License fixes: pcf2127, da9063
- wakeup-source support for isl12057 and opal"
* tag 'rtc-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (23 commits)
rtc: Add a driver for Micro Crystal RV8803
rtc: s3c: Set year, month, day value for setting alarm
rtc: ds1307: Fix alarm programming for mcp794xx
rtc: isl12057: enable support for the standard "wakeup-source" property
rtc: opal: enable support for the stardard "wakeup-source" property
rtc: isl1208: Pass the IRQF_ONESHOT flag
rtc: pcf8563: add CLKOUT to common clock framework
rtc: davinci: remove incorrect reference to probe function
rtc: at91rm9200: clear RTC alarm status flag prior to suspending
rtc: pcf2127: remove useless driver version
rtc: pcf2127: fix reading uninitialized value on RTC_READ_VL ioctl
rtc: stmp3xxx: unify register access macros
rtc: da9063: GPL copyright inconsistency fix
rtc: pcf85063: return an error when date is invalid
rtc: rx8025: remove unnecessary braces
rtc: ds1343: remove misuse of IRQF_NO_SUSPEND flag
rtc: ab8500: remove misuse of IRQF_NO_SUSPEND flag
rtc: pl031: remove misuse of IRQF_NO_SUSPEND flag
rtc: opal: fix type of token
rtc: ds1390: Add trickle charger device tree binding
...
This driver supports the following functions:
- reading and settings time
- alarms when connected to an IRQ
- reading and clearing the voltage low flags
- nvram
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This patch sets year, month, day value for set_alarm function.
The current driver omits to set the values.
This fixes setting wake alarm for dates different than current day.
Without the patch the alarm scheduled for tomorrow would fire today on
chosen time.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.kim@samsung.com>
Signed-off-by: KyungMin Park <kyungmin.park@samsung.com>
[k.kozlowski: Rebase and test the patch, update commit message]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
mcp794xx alarm registers must be written in BCD format. However, the
alarm programming logic neglected this by adding one to the value
after bin2bcd conversion has been already done, writing bad values
to month register in case the alarm being set is in October. In this
case, the alarm month value becomes 0x0a instead of the expected 0x10.
Fix by moving the +1 addition within the bin2bcd call also.
Fixes: 1d1945d261 ("drivers/rtc/rtc-ds1307.c: add alarm support for mcp7941x chips")
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Though the isl12057 rtc driver should and will continue to support the
legacy "isil,irq2-can-wakeup-machine" property to enable RTC as the
wakeup source, we need to add support for the new standard property
"wakeup-source".
This patch adds support for "wakeup-source" property in addition to the
existing "isil,irq2-can-wakeup-machine" property.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: rtc-linux@googlegroups.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
