If a command cannot be sent or there is a internal error an errno maybe
set instead of a command status.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If a hardware error occurs and the connections are flushed without a
disconnection_complete event being signaled, the temporary linkkeys are
not flushed.
This change ensures that any outstanding flushable linkkeys are flushed
when the connection are flushed from the hash table.
Additionally, this also makes use of test_and_clear_bit to avoid
multiple attempts to delete the link key that's already been flushed.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The handling of connection failures shall be handled by the request
completion callback as already done by hci_cs_le_create_conn, also make
sure to use hci_conn_failed instead of hci_le_conn_failed as the later
don't actually call hci_conn_del to cleanup.
Link: https://github.com/bluez/bluez/issues/340
Fixes: 8e8b92ee60 ("Bluetooth: hci_sync: Add hci_le_create_conn_sync")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN quirk which can be
used to mark HCI_Enhanced_Setup_Synchronous_Connection as broken even
if its support command bit are set since some controller report it as
supported but the command don't work properly with some configurations
(e.g. BT_VOICE_TRANSPARENT/mSBC).
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This attempts to cleanup the hci_conn if it cannot be aborted as
otherwise it would likely result in having the controller and host
stack out of sync with respect to connection handle.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
hci_le_conn_failed function's documentation says that the caller must
hold hdev->lock. The only callsite that does not hold that lock is
hci_le_conn_failed. The other 3 callsites hold the hdev->lock very
locally. The solution is to hold the lock during the call to
hci_le_conn_failed.
Fixes: 3c857757ef ("Bluetooth: Add directed advertising support through connect()")
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When one of the three connection complete events is received multiple
times for the same handle, the device is registered multiple times which
leads to memory corruptions. Therefore, consequent events for a single
connection are ignored.
The conn->state can hold different values, therefore HCI_CONN_HANDLE_UNSET
is introduced to identify new connections. To make sure the events do not
contain this or another invalid handle HCI_CONN_HANDLE_MAX and checks
are introduced.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=215497
Signed-off-by: Soenke Huster <soenke.huster@eknoes.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds hci_le_create_conn_sync and make hci_le_connect use it instead
of queueing multiple commands which may conflict with the likes of
hci_update_passive_scan which uses hci_cmd_sync_queue.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This makes hci_suspend_notifier use the hci_*_sync which can be
executed synchronously which is allowed in the suspend_notifier and
simplifies a lot of the handling since the status of each command can
be checked inline so no other work need to be scheduled thus can be
performed without using of a state machine.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This replaces the use of hci_update_background_scan with
hci_update_passive_scan which runs from cmd_work_sync and deal properly
with resolving list when LL privacy is enabled.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In Enhanced_Setup_Synchronous_Command, add support for msbc
coding format
Signed-off-by: Kiran K <kiran.k@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
For HFP offload use case, codec needs to be configured
before opening SCO connection. This patch sends
HCI_CONFIGURE_DATA_PATH command to configure doec before
opening SCO connection.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When connecting to a device using an RPA if the address has been
resolved by the controller (types 0x02 and 0x03) the identity address
shall be used as the actual RPA in the advertisement won't be visible
to the host.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replaces some non-inclusive terms based on the appropriate
language mapping table compiled by the Bluetooth SIG:
https://specificationrefs.bluetooth.com/language-mapping/Appropriate_Language_Mapping_Table.pdf
Specifically, these terms are replaced:
master -> initiator (for smp) or central (everything else)
slave -> responder (for smp) or peripheral (everything else)
The #define preprocessor terms are unchanged for now to not disturb
dependent APIs.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replaces some non-inclusive terms based on the appropriate
language mapping table compiled by the Bluetooth SIG:
https://specificationrefs.bluetooth.com/language-mapping/Appropriate_Language_Mapping_Table.pdf
Specifically, these terms are replaced when describing the
connectionless peripheral broadcast feature:
master -> central
slave -> peripheral
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When suspending, Bluetooth disconnects all connected peers devices. If
an LE connection is started but isn't completed, we will see an LE
Create Connection Cancel instead of an HCI disconnect. This just adds
a check to see if an LE cancel was the last disconnected device and wake
the suspend thread when that is the case.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If a peer device doesn't support eSCO 2M we should skip the params that
use it when setting up sync connection since they will always fail.
Signed-off-by: Yu Liu <yudiliu@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When an LE connection request is made, advertising is disabled and never
resumed. When a client has an active advertisement, this is disruptive.
This change adds resume logic for client-configured (non-directed)
advertisements after the connection attempt.
The patch was tested by registering an advertisement, initiating an LE
connection from a remote peer, and verifying that the advertisement is
re-activated after the connection is established. This is performed on
Hatch and Kukui Chromebooks.
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Drop repeated words in net/bluetooth/.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this patch if le_create_conn process is started restrict to
disable address resolution and same is disabled during
le_enh_connection_complete
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add functionality to disable and remove advertising instances,
and use that functionality in MGMT add/remove advertising calls.
Currently, advertising is globally-disabled, i.e. all instances are
disabled together, even if hardware offloading is available. This
patch adds functionality to disable and remove individual adv
instances, solving two issues:
1. On new advertisement registration, a global disable was done, and
then only the new instance was enabled. This meant only the newest
instance was actually enabled.
2. On advertisement removal, the structure was removed, but the instance
was never disabled or removed, which is incorrect with hardware offload
support.
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Reviewed-by: Shyh-In Hwang <josephsih@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If user decides to cancel the ongoing pairing process (e.g. by clicking
the cancel button on pairing/passkey window), abort any ongoing pairing
and then terminate the link if it was created because of the pair
device action.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch centralized the initialization of default parameters. This
is required to allow clients to more easily customize the default
system parameters.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
EIR flags should just hint if SSP may be supported but we shall verify
this with use of the actual features as the SSP bits may be disabled in
the lower layers which would result in legacy authentication to be
used.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
notifying using HCI_NOTIFY_CONN_ADD for SCO connection is generic in
case of mSBC audio. To differntiate SCO air mode introducing
HCI_NOTIFY_ENABLE_SCO_CVSD and HCI_NOTIFY_ENABLE_SCO_TRANSP.
Signed-off-by: Sathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Disabling LE_LEGACY_ADV when LE_EXT_ADV is enabled causes 'command
disallowed . This patch fixes that issue and disables EXT_ADV if
enabled.
Signed-off-by: Sathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Extended advertising Data is set during bluetooth initialization
by default which causes InvalidHCICommandParameters when setting
Extended advertising parameters.
As per Core Spec 5.2 Vol 2, PART E, Sec 7.8.53, for
advertising_event_property LE_LEGACY_ADV_DIRECT_IND does not
supports advertising data when the advertising set already
contains some, the controller shall return erroc code
'InvalidHCICommandParameters(0x12).
So it is required to remove adv set for handle 0x00. since we use
instance 0 for directed adv.
Signed-off-by: Sathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Disabling LEGACY_ADV when EXT_ADV is enabled causes
'command disallowed' during DIRECTED_ADV. This Patch fixes this
issue.
Signed-off-by: Sathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds BT_PHY socket option (read-only) which can be used to read
the PHYs in use by the underline connection.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In the implementation of hci_connect_le_scan() when conn is added via
hci_conn_add(), if hci_explicit_conn_params_set() fails the allocated
memory for conn is leaked. Use hci_conn_del() to release it.
Fixes: f75113a260 ("Bluetooth: add hci_connect_le_scan")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
It appears that some Broadcom controllers (eg BCM20702A0) reject LE Set
Advertising Parameters command if advertising intervals provided are not
within range for undirected and low duty directed advertising.
Workaround this bug by populating min and max intervals with 'valid'
values.
< HCI Command: LE Set Advertising Parameters (0x08|0x0006) plen 15
Min advertising interval: 0.000 msec (0x0000)
Max advertising interval: 0.000 msec (0x0000)
Type: Connectable directed - ADV_DIRECT_IND (high duty cycle) (0x01)
Own address type: Public (0x00)
Direct address type: Random (0x01)
Direct address: E2:F0:7B:9F:DC:F4 (Static)
Channel map: 37, 38, 39 (0x07)
Filter policy: Allow Scan Request from Any, Allow Connect Request from Any (0x00)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Advertising Parameters (0x08|0x0006) ncmd 1
Status: Invalid HCI Command Parameters (0x12)
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Tested-by: Sören Beye <linux@hypfer.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This makes use of controller sets when using Extended Advertising
feature thus offloading the scheduling to the controller.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Changes made to add HCI Write Authenticated Payload timeout
command for LE Ping feature.
As per the Core Specification 5.0 Volume 2 Part E Section 7.3.94,
the following code changes implements
HCI Write Authenticated Payload timeout command for LE Ping feature.
Signed-off-by: Spoorthi Ravishankar Koppad <spoorthix.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When trying to align the minimum encryption key size requirement for
Bluetooth connections, it turns out doing this in a central location in
the HCI connection handling code is not possible.
Original Bluetooth version up to 2.0 used a security model where the
L2CAP service would enforce authentication and encryption. Starting
with Bluetooth 2.1 and Secure Simple Pairing that model has changed into
that the connection initiator is responsible for providing an encrypted
ACL link before any L2CAP communication can happen.
Now connecting Bluetooth 2.1 or later devices with Bluetooth 2.0 and
before devices are causing a regression. The encryption key size check
needs to be moved out of the HCI connection handling into the L2CAP
channel setup.
To achieve this, the current check inside hci_conn_security() has been
moved into l2cap_check_enc_key_size() helper function and then called
from four decisions point inside L2CAP to cover all combinations of
Secure Simple Pairing enabled devices and device using legacy pairing
and legacy service security model.
Fixes: d5bb334a8e ("Bluetooth: Align minimum encryption key size for LE and BR/EDR connections")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203643
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The minimum encryption key size for LE connections is 56 bits and to
align LE with BR/EDR, enforce 56 bits of minimum encryption key size for
BR/EDR connections as well.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
This basically sets the random address for the adv instance
Random address can be set only if the instance is created which
is done in Set ext adv param.
Random address and rpa expire timer and flags have been added
to adv instance which will be used when the respective
instance is scheduled.
This introduces a hci_get_random_address() which returns the
own address type and random address (rpa or nrpa) based
on the instance flags and hdev flags. New function is required
since own address type should be known before setting adv params
but address can be set only after setting params.
< HCI Command: LE Set Advertising Set Random Address (0x08|0x0035) plen 7
Advertising handle: 0x00
Advertising random address: 3C:8E:56:9B:77:84 (OUI 3C-8E-56)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Advertising Set Random Address (0x08|0x0035) ncmd 1
Status: Success (0x00)
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch does extended advertising for directed advertising
if the controller supportes. Instance 0 is used for directed
advertising.
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use the selected PHYs by Set PHY Configuration management command
in extended create connection.
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This implements extended LE craete connection and enhanced
LE conn complete event if the controller supports.
For now it is as good as legacy LE connection and event as
no new features in the extended connection is handled.
< HCI Command: LE Extended Create Connection (0x08|0x0043) plen 26
Filter policy: White list is not used (0x00)
Own address type: Public (0x00)
Peer address type: Random (0x01)
Peer address: DB:7E:2E:1D:85:E8 (Static)
Initiating PHYs: 0x01
Entry 0: LE 1M
Scan interval: 60.000 msec (0x0060)
Scan window: 60.000 msec (0x0060)
Min connection interval: 50.00 msec (0x0028)
Max connection interval: 70.00 msec (0x0038)
Connection latency: 0 (0x0000)
Supervision timeout: 420 msec (0x002a)
Min connection length: 0.000 msec (0x0000)
Max connection length: 0.000 msec (0x0000)
> HCI Event: Command Status (0x0f) plen 4
LE Extended Create Connection (0x08|0x0043) ncmd 2
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 31
LE Enhanced Connection Complete (0x0a)
Status: Success (0x00)
Handle: 3585
Role: Master (0x00)
Peer address type: Random (0x01)
Peer address: DB:7E:2E:1D:85:E8 (Static)
Local resolvable private address: 00:00:00:00:00:00 (Non-Resolvable)
Peer resolvable private address: 00:00:00:00:00:00 (Non-Resolvable)
Connection interval: 67.50 msec (0x0036)
Connection latency: 0 (0x0000)
Supervision timeout: 420 msec (0x002a)
Master clock accuracy: 0x00
@ MGMT Event: Device Connected (0x000b) plen 40
LE Address: DB:7E:2E:1D:85:E8 (Static)
Flags: 0x00000000
Data length: 27
Name (complete): Designer Mouse
Appearance: Mouse (0x03c2)
Flags: 0x05
LE Limited Discoverable Mode
BR/EDR Not Supported
16-bit Service UUIDs (complete): 1 entry
Human Interface Device (0x1812)
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In case of using BT_ERR and BT_INFO, convert to bt_dev_err and
bt_dev_info when possible. This allows for controller specific
reporting.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If command is added to req then it should be freed in case if
hdev is down or HCI_ADVERTISING flag is set.
This introduces a helper in hci_request to purge the cmd_q
to make cmd_q internal to hci_request which is used to fix
the leak.
This also replace accessing of cmd_q in hci_conn with the
new helper.
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The hci_get_route() API is used to look up local HCI devices, however
so far it has been incapable of dealing with anything else than the
public address of HCI devices. This completely breaks with LE-only HCI
devices that do not come with a public address, but use a static
random address instead.
This patch exteds the hci_get_route() API with a src_type parameter
that's used for comparing with the right address of each HCI device.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
